Search
Filters
total: 5894
-
Catalog
displaying 1000 best results Help
Search results for: three-level inverter
-
СИСТЕМА КОНТРОЛЯ СОСТОЯНИЯ ИЗОЛЯЦИИ ЭЛЕКТРОПРИВОДОВ В СЕТЯХ С ГЛУХОЗАЗЕМЛЕННОЙ НЕЙТРАЛЬЮ (System of insulation status monitoring for electric drives in networks with a dead-earth neutral)
PublicationПредложен метод контроля изоляции частотно-регулируемых электроприводов в сетях с глухозаземленной нейтралью. Система контроля изоляции включается в момент остановки электропривода. Ключи инвертора коммутируются по специальному закону, и с помощью сигнала трансформатора тока, который изме- ряет ток во всех трех фазах привода одновременно, определяется ток утечки. Рассмотрена схема датчика тока утечки и приведены экспериментальные...
-
A Wind Energy Conversion System Based on a Generator with Modulated Magnetic Flux
PublicationIn this work, the concept of an energy conversion system for wind turbines based on the modified permanent magnet synchronous generator (PMSG) is presented. In the generator, a pair of three-phase windings is used, one of which is connected in a “star” and the second in a “delta” configuration. At the outputs of both windings, two six-pulse uncontrolled (diode) rectifiers are included. These rectifiers are mutually coupled by a...
-
Resonant DC link inverters for AC motor drive systems – critical evaluation
PublicationIn this survey paper, resonant and quasiresonant DC link inverters are reexamined for AC motor drive applications. Critical evaluation of representative topologies is based on simulation and waveform analysis to characterize current/voltage stress of components, control timing constraints and feasibility. A special concern over inverter common-mode voltage and voltage gradient du/dt limitation capacity is discussed for motor bearing...
-
Failure analysis of a high-speed induction machine driven by a SiC-inverter and operating on a common shaft with a high-speed generator
PublicationDue to ongoing research work, a prototype test rig for testing high-speed motors/generators has been developed. Its design is quite unique as the two high- speed machines share a single shaft with no support bearings between them. A very high maximum operating speed, up to 80,000 rpm, was required. Because of the need to minimise vibration during operation at very high rotational speeds, rolling bearings were used. To eliminate...
-
Augmented speed control scheme of dual induction motors with mutual flux angle control loop
PublicationThis paper proposes an augmented speed control scheme of dual induction motors fed by a five-leg voltage source inverter (VSI) with a common/shared-leg. An additional control loop is proposed here and based on the mutual flux angle – the difference between flux angular positions of the IMs. The main purpose of this research is to minimize the energy losses in the common inverter leg by controlling the mutual flux angle, at equal...
-
Quasi-discrete modelling of PMSM phase currents in drives with low switching-to-fundamental frequency ratio
PublicationThis study proposes a new quasi-discrete approach to modelling the permanent magnet synchronous motor (PMSM). The quasi-discrete modelling reflects the impact of continuous rotor movement, which takes place during a control cycle, on the shape of motor current waveforms. This provides much improvement in current modelling accuracy under inverter low switching-to-fundamental frequency operation. The proposed approach may be used...
-
Transient modeling in common DC link of power converters
PublicationПредмет исследования. Представлена математическая модель силовых преобразователей электропривода, питающихся от общего звена постоянного тока, на примере тяговых электроприводов карьерного самосвала БЕЛАЗ-90 мощностью 280 кВт. Модель выполнена в пакете MATLAB/Simulink. Новизна предложенной модели заключается в применении новой топологии силовой схемы для исследования работы двух инверторов, под- ключенных к одному звену постоянного...
-
Synchronized six-step voltage generation in high-speed PMSM drive
PublicationSynchronized voltage generation has already been considered in the context of pulse width modulation (PWM). References prove that synchronized PWM substantially decreases subharmonics in inverter output voltage when operating with low switching-to-fundamental frequency ratio. This paper identifies problems of unsynchronized voltage generation in electric drives under six-step inverter operation. Guidelines for the synchronization...
-
Bezczujnikowe sterowanie trakcyjnym silnikiem IPMSM małej mocy
PublicationThis paper describes an algorithm for estimation of IPMSM angular rotor position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. Control of the IPMSM electromagnetic torque requires a precise estimation of the rotor angular position throughout the wide speed range. This involves using a set of estimation methods switched with the dependence on the actual rotor...
-
Modeling the impact of rotor movement on non-linearity of motor currents waveforms in high-speed PMSM drives
PublicationMotor current measurement techniques as well as predictive control algorithms for electric drives rely on an assumption of linear motor currents changes resulting from constant inverter output voltages. Recent research has reported that this assumption does not hold in motors with short electrical time constant, and in drives whose rotor position advances substantially during a control period. This paper proposes a simulation model...
-
The multiscalar control of induction motor with the sliding mode controllers
PublicationThe control structure of induction motor is proposed in this paper. The structure of multiscalar control with conventional PI - controllers is well known in literature. The sliding mode multiscalar control (SMMC) conception is presented in this paper. The induction motor is fed by voltage source inverter. Comparison between two multiscalar control method is showed.
-
Oversizing the photovoltaic generator capacity in a micro photovoltaic plant
PublicationA significant part of photovoltaic micro installations in Poland is characterized by photovoltaic generator oversizing in relation to the inverter. The idea of oversizing, however, still raises doubts among some plant owners. In the paper, the energy yield of installation with an oversized and not oversized photovoltaic generator is presented on selected examples, showing the legitimacy of oversizing.
-
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublicationIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
Appendix E
PublicationThe advance of variable speed drives systems (VSDs) engineering highlights the need of specific technical guidance provision by electrical machines and drives manufacturers, so that such applications can be properly designed to present advantages in terms of both energy efficiency and expenditure. This book presents problems and solutions related to inverter-fed electrical motors. Practically orientated, the book describes the...
-
Romanika Okraszewska dr inż. arch.
PeopleRomanika Okraszewska, Ph.D., Eng. Arch., is an Assistant Professor at the Faculty of Civil and Environmental Engineering of Gdańsk University of Technology (GUT). Graduated from the mathematical and informatical class at the National Education Commission High School in Gdańsk. Graduated from two faculties of Gdańsk University of Technology, Architecture and Urban Planning (2002) and Management and Economics (2004). Participant...
-
Synteza bezczujnikowego sterowania maszyną indukcyjną klatkową zasilaną z falownika prądu
PublicationSynteza bezczujnikowego sterowania maszyną indukcyjną klatkową zasilaną z falownika prądu stanowi cel niniejszej monografii. Praca zawiera podstawowe informacje na temat modelowania układu napędowego z maszyną indukcyjną klatkową zasilaną z falownika prądu. Przedstawiono informacje na temat linearyzacji nieliniowych obiektów. Na pod-stawie metody syntezy strukturalnej opracowano nowe transformacje do postaci zmien-nych multiskalarnych,...
-
Increasing the Utilization of dc-link Voltage of a Five-Leg VSI Based on Rotor Angle Control of Dual Induction Motors
PublicationThis paper introduces an increased utilization of the dc-link voltage of a five-leg voltage source inverter (VSI) based on the rotor flux angle control technique for dual induction motors, IM. The main purpose is to utilize additional abilities provided by a multi-motor drive system in limited operating conditions. Generally, a multi-motor drive system is widely used in electric vehicles (EVs), traction systems and in several industrial...
-
Electric shock hazard in circuits with variable-speed drives
PublicationThe conventional approach to electrical safety under fault condition in typical power systems considers earth fault currents of sinusoidal waveform and frequency of 50/60 Hz. However, in circuits with variable-speed drives, there is earth fault current flow with harmonics, and these harmonics influence the threshold of ventricular fibrillation. The paper presents earth fault current waveforms in circuits with variable-speed drives...
-
Simulation model of IPMSM drive with rotor position estimator
PublicationThe paper presents a simulation model of electric drive consisting of: IPMSM motor, inverter and digital controller. The model was designed in Mathlab/Simulink. By modelling of the controller its discrete operation was taken into account in order to simulate precisely a specific sensorless control algorithm. A method for estimation of angular rotor position was proposed. Its mathematical algorithm was explained and errors were...
-
Compensation of Dead Time Effects for Shunt Active Power Filters
PublicationThe paper presents a comprehensive approach to the compensation of the grid current distortion for shunt active power filter systems. Four different sources of current distortion are addressed: imperfect grid synchronization caused by the distortion in the grid voltages, time delays in the estimation of compensating currents and grid voltages, fluctuations of the dc bus voltage, and the distortion of inverter output voltages due...
-
Pulse-Width Modulation of Power Electronic DC–AC Converter
PublicationThe Second Edition of High Performance Control of AC Drives with Matlab®/Simulink delivers an updated and thorough overview of topics central to the understanding of AC motor drive systems. The book includes new material on medium voltage drives, covering state-of-the-art technologies and challenges in the industrial drive system, as well as their components, and control, current source inverter-based drives, PWM techniques for...
-
Comprehensive compensation of grid current distortion by shunt active power filters
PublicationThe paper presents a comprehensive approach to the compensation of grid current distortion in shunt active power filter systems. Four sources of current distortion are addressed: imperfect grid synchronization caused by the distortion in the grid voltages, time delays in the evaluation of grid voltages and computation of compensating currents, fluctuations of the dc bus voltage, and the distortion of inverter output voltages due...
-
Usługi publiczne jako czynnik miastotwórczy i wyznacznik rangi miasta w sieci osadniczej na przykładzie małych miast Polski północnej
PublicationMałe miasta, podobnie jak większe, pełnią różne funkcje egzogeniczne wyspecjalizowane, a także funkcje standardowe, zwane też centralnymi (Domański 1972), polegające na obsłudze bliskiego, a nieraz też dalszego otoczenia. Są z tego powodu koncentracjami miejsc pracy dla mieszkańców swoich i otoczenia. Jedną z funkcji miastotwórczych są usługi. Ich udział w strukturze zatrudnienia, jak wykazywał Fourastier (Goryński 1966) rośnie...
-
Evaluation the environmental fate of pharmaceuticals using a level III model based on poly-parameter linear free energy relationships
PublicationOpisano możliwości zastosowania modelu ''Level III Model'' do opisu losu środowiskowego pozostałości farmaceutyków w środowisku. Zastosowany model umożliwia oszacowanie trwałości, stężeń oraz transportu poszczególnych zanieczyszczeń pomiędzy poszczególnymi elementami składowymi środowiska (powietrze, woda, gleba i osady denne).
-
Estimation of interior-permanent-magnet-synchronous-motor rotor position by analysis of phase-current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM rotor angular position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Calculation of the motor position is performed in every PWM cycle. The standard SV-PWM method is used to determine...
-
Possibility of Fault Detection in Sensorless Electric Drives
PublicationThe work presents a fault detection method for an induction motor drive system with inverter output filter. This approach make use of a load torque state observer, which complete structure is presented along with the used control structure. Moreover, the demonstrated drive system operates without rotor speed measurement in conjunction with the multiscalar control. The verification of the demonstrated idea was performed on an experimental...
-
Development and performance analysis of a novel multiphase doubly-fed induction generator
PublicationThis paper presents the research into the design and performance analysis of a novel five-phase doubly-fed induction generator (DFIG). The designed DFIG is developed based on standard induction motor components and equipped with a five-phase rotor winding supplied from the five-phase inverter. This approach allows the machine to be both efficient and reliable due to the ability of the five-phase rotor winding to operate during...
-
Sensorless algorithm for sustaining controllability of IPMSM drive in electric vehicle after resolver fault
PublicationThis paper presents a sensorless algorithm designated for the emergency control of an interior permanent magnet synchronous motor (IPMSM) drive in electric or hybrid vehicle. The algorithm is based on analysing the derivatives of motor phase currents measured over the duration of particular inverter states. The method is computationally simple and does not require additional hardware since the derivatives are measured indirectly....
-
IPMSM rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes an algorithm for estimation of IPMSM angular rotor position. The algorithm uses derivatives of motor phase currents resulting from PWM modulation to obtain the rotor position. The presented method is designed for medium- and high-speed range, since it is based on determination of the EMF vector. Algorithm is characterised by a very simple formulae. The calculation of rotor position is performed in every PWM...
-
Wireless Charging Station Design for Electric Scooters: Case Study Analysis
PublicationThis study proposes an example of a wireless charging station design for a small-scale vehicle available on the market. The article analyzes basic transmitter inverter topologies and their compensation methods in terms of flexibility of control, tolerance to uncertainty in positioning, and the possibility of decreasing the integration price. Our comprehensive analysis focuses on the battery voltage range, energy capacity, cost,...
-
Induction machine behavioral modeling for prediction of EMI propagation.
PublicationThis paper presents the results of wideband behavioral modeling of an induction machine (IM). The proposed solution enables modeling the IM differential- and common-mode impedance for a frequency range from 1 kHz to 10 MHz. Methods of parameter extraction are derived from the measured IM impedances. The developed models of 1.5 kW and 7.5 kW induction machines are designed using the Saber Sketch scheme editor and simulated in the...
-
Quasi-ciągły pomiar geometrii rozjazdów kolejowych
PublicationW czasie budowy nowych torów i rozjazdów kolejowych, jak również w procesie ich utrzymania, należy wykonać odpowiednie pomiary i ocenić stan geometrii badanej infrastruktury. Pomiary te mogą być wykonane z wykorzystaniem jednego z trzech systemów pomiarowych: pojazdami pomiarowymi, maszynami do budowy i utrzymania lub urządzeniami lekkimi i ręcznymi. W artykule przedstawiona została metoda pomiarów szerokości toru i przechyłki...
-
Frequency-Variant Double-Zero Single-Pole Reactive Coupling Networks for Coupled-Resonator Microwave Bandpass Filters
PublicationIn this work, a family of frequency-variant reactive coupling (FVRC) networks is introduced and discussed as new building blocks for the synthesis of coupled-resonator bandpass filters with real or complex transmission zeros (TZs). The FVRC is a type of nonideal frequency-dependent inverter that has nonzero elements on the diagonal of the impedance matrix, along with a nonlinear frequency-variation profile of its transimpedance...
-
WYDATKI INWESTYCYJNE WOJEWÓDZTW SAMORZĄDOWYCH PO WPROWADZENIU INDYWIDUALNEGO WSKAŹNIKA ZADŁUŻENIA
PublicationOkreślenie dopuszczalnego poziomu zadłużenia jest ważną kwestią dla każdej jednostki samorządu terytorialnego w Polsce, a jej ranga jeszcze rośnie, jeśli samorząd odczuwa silną presję na dbanie o rozwój obszaru, na którym funkcjonuje, borykając się równocześnie z niedostatkiem dochodów. Taka sytuacja dotyczy większości województw samorządowych, które spośród wszystkich szczebli struktury samorządowej...
-
Control system for contactless electrical energy transfer with varying air gap
PublicationInductive power transfer (IPT) is a system by which electrical energy may be transmitted without electrical connection through a large air gap between coils. Systems usually considered in the literature are the ones with a constant air gap. The paper describes the analysis of IPT, which allows for supplying an electrical load in the conditions of slow, in relation to the dynamics of power supply, changes in the dimensions of the...
-
Voltage and frequency regulation of a standalone induction generator by reduced-rating power electronic compensators - comparative evaluation
PublicationIn this paper are considered two fundamental topologies of power electronic compensators for voltage and frequency control of a standalone self-excited induction generator (IG) system. These are voltage and current source inverter based shunt compensators with energy storage. The aim of this study is to assess main features of both topologies in dynamic and steady-state IG operation. The whole system is modelled with the aid of...
-
A Novel Synthesis Technique for Microwave Bandpass Filters with Frequency-Dependent Couplings
PublicationThis paper presents a novel synthesis technique for microwave bandpass filters with frequency-dependent couplings. The proposed method is based on the systematic extraction of a dispersive coupling coefficient using an optimization technique based on the zeros and poles of scattering parameters representing two coupled resonators.The application of this method of synthesis is illustrated using two examples involving four and five-pole...
-
IDENTYFIKACJA CZYNNIKÓW WPŁYWAJĄCYCH NA BEZPIECZEŃSTWO EKSPLOATACJI STATKU NA ŚRÓDLĄDOWEJ DRODZE WODNEJ W DELCIE WISŁY
PublicationKażdego roku w Polsce, na śródlądowych drogach wodnych rejestrowane są przez Urzędy Żeglugi Śródlądowej, Państwową Straż Pożarną i Policję wypadki i incydenty, prowadzące zarówno do uszkodzenia infrastruktury jak i uszczerbku na zdrowiu. Poprawa poziomu bezpieczeństwa wymaga dogłębnej analizy i wyciągania wniosków z zaistniałych sytuacji awaryjnych. Istotną rzeczą jest identyfikacja i usystematyzowanie zagrożeń występujących w...
-
Library Information Skills - Level 1
e-Learning CoursesThe Gdańsk Tech Library offers Library Information Skills e-course to the students enrolled in English-language degree programmes at Gdańsk University of Technology (Gdańsk Tech). It is an obligatory course. There is a test at the end of the e-course. Information skills, or in other words information literacy, means knowing what kind of information a student is looking for, where to find it, how to evaluate, communicate and use...
-
ZARZĄDZANIE ZESPOŁEM WIRTUALNYM JAKO WYZWANIE DLA LIDERA ZESPOŁU
PublicationRozdział dotyczy zarządzania zespołem wirtualnym, który charakteryzuje się rozproszeniem członków zespołu oraz współpracą za pośrednictwem technologii informacyjnej. Tak funkcjonujące zespoły nakładają na lidera dodatkowe wyzwania związane z koniecznością kompensowania braku bezpośredniego kontaktu oraz samodzielnością poszczególnych osób w zespole. Przedstawiono najważniejsze zadania, które podnoszą efektywność zarządzania zespołem...
-
Indirect Measurement of Motor Current Derivatives in PMSM Sensorless Drives
PublicationMotor current derivatives contain useful information for control algorithms, especially in sensorless electric drives. The measurement of motor current derivatives in electric motors supplied by voltage source inverter can be performed using di/dt transducers. However, in such a solution additional sensors have to be installed, e.g. Rogowski coils. Another approach is to measure current derivatives indirectly – by oversampling...
-
Accurate design of pseudoelliptic inline SIW filters with frequency-dependent couplings
PublicationThis paper presents an accurate synthesis method for inline SIW (Substrate Integrated Waveguide) generalized Chebyshev bandpass filters with frequency-dependent couplings. The technique is based on the synthesis of a coupling matrix that takes into account the impedance of the frequency-dependent stub. Thus, a loading effect compensation in adjacent resonators (via resonant frequency adjustment) and coupling elements (via coupling-value...
-
Dynamic characteristics of the proton exchange membrane fuel cell module
PublicationThe paper describes a fuel cell based system and its performance. The system is based on two fuel cell units, DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and a set of measurement instruments. In the study presented in the paper a dynamic response of the proton exchange membrane (PEM) fuel cell system to unit step change load as well as to periodical load changing cycles...
-
Three Seas Economic Journal
Journals -
Od modelu biznesu przedsiębiorstwa do modelu biznesu organizacji publicznej
PublicationZadowolenie obywateli z jakości życia jest związane z poziomem zaspokajania ich potrzeb, wśród których występuje możliwość korzystania z dóbr publicznych. Wiąże się to z dostępem do usług publicznych. Gospodarzami w zakresie świadczenia tych usług są organizacji publiczne. Zatem z rozumowania logicznego wynika, że wzrost zadowolenia mieszkańców może nastąpić wówczas, gdy podniesie się dostępność i poziom jakości usług publicznych....
-
Simulation Studies of Control Systems for Doubly Fed Induction Generator Supplied by the Current Source Converter
PublicationThe control system for a Doubly Fed Induction Generator (DFIG) supplied by a grid-connected Current Source Converter (CSC) is presented in this paper. Nonlinear transformation of DFIG model to the multi-scalar form is proposed. The nonlinear control strategy of active and reactive power of DFIG is realized by feedback linearization. In the proposed control scheme, the DFIG model and CSI parameters are included. Two Proportional-Integral...
-
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
PublicationIn order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming (ADP) technique based on the internal model principle (IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback, merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization...
-
Time-domain measurement methods for R, L and C sensors based on aversatile direct sensor-to-microcontroller interface circuit
PublicationtIn the paper new time-domain measurement methods for determining values of resistive (R), inductive(L) and capacitive (C) sensors based on a versatile direct sensor-to-microcontroller interface for microcon-trollers with internal analog-to-digital converters (ADCs) and analog comparators (ACs) are presented.The interface circuit consists of a reference resistor Rrworking as a voltage divider, a given R, L or C sensorand a microcontroller...
-
Gdyńskie chłodnie portowe - studium przypadku przemysłowej architektury portowej okresu modernizmu
PublicationArtykuł podejmuje tematykę obiektów monumentalnej architektury przemysłowej portu gdyńskiego, o funkcji chłodni. Rozwój technologii chłodzenia spowodował, że od połowy XIX w. obiekty takie budowano w dużych, zazwyczaj międzynarodowych ośrodkach dla zapewnienia wysokiego poziomu obsługi handlu produktami łatwo psującymi się. Dynamiczny rozwój portowego zaplecza Gdyni w okresie międzywojennym zaowocował powstaniem aż trzech budowli...
-
Jan Ostoj dr hab.
PeopleProf. Assoc. dr hab. Jan Ostoj – rector of the Bielsko-Biała School of Finances and Law between 1999 and 2020, currently head of Banking and Finances Department at the same school, lecturer and researcher in the area of economics and finances with more than 40 years of experience. Co-creator of two faculties of the school managed and two off-campus teaching centres. Previously employed at the Faculty of Social Sciences at the University...