Search
Filters
total: 281
Search results for: DIRECT SHEAR
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Shaft friction from the DMT and direct shear interface tests
PublicationThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Design of poroelastic wearing course with the use of direct shear test
PublicationPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Scale effect in shaft friction from direct shear tests
PublicationPrzeanalizowano wartości maksymalne tarcia uzyskane w aparacie bezpośredniego ścinania w kontakcie konstrukcja-grunt dla piasków kwarcowych i węglanowych oraz gładkiego i szorstkiego kontaktu. Badania przeprowadzono przy regulowanej sztywności normalnej kontaktu, przy różnej składowej normalnej naprężenia w kontakcie i różnym zagęszczeniu gruntu. Określono efekt skali jako stosunek wartości tarcia mobilizowanego na modelu do tarcia...
-
FE-analysis of shearing of granular bodies in a direct shear box
PublicationW artykule przedstawiono wyniki numerycznej obszernej analizy testu bezpośredniego ścinania. w materiałach granulowanych. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. Analizę wykonano dla różnego poziomu obciażenia, długości charakterystycznej, wskaźnika porowatości, długości próbki W analizie uwzględniono lokalizacje odkształceń stycznych.
-
Direct shear stress vs strain relation for fiber reinforced composites
PublicationThe majority of fiber reinforced composites exhibit strong non-linear behavior in in-plane shear state. The effect is attributed to the micro-cracks appearing in the matrix and can be modeled on the micro and macro level. In this work the author proposes constitutive laws describing the non-linear in-plane shear response, which can be alternative for the relations commonly considered in the literature. The proposed equations are...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Applications of permeability, oedometer and direct shear tests to the sand mixed with waste tire crumb
PublicationThe amount of the used waste rubbers in the world has been increasing every year, and their utilization, become a major environmental problem worldwide. The present experimental work has been performed to investigate the influence of rubber inclusion on the behavior of a sand. Geotechnical properties of the sand, and sand with tire crumb at various ratios mixtures (0%, 2.5%, 7.5%, and 15%) were investigated through a series of...
-
Discrete modelling results of a direct shear test for granular materials versus FE results
PublicationArtykuł porównuje wyniki DEM i MES dla testu bezpośredniego ścinania materiałów granulowanych. Obliczenia MES wykonano przy zastosowaniu mikropolarnego modelu hipoplastycznego. W obliczeniach DEM z kulami i momentami kontaktu zwrócono uwagę na zjawiska mikrostrukturalne w strefie ścinania na poziomie ziaren.
-
Verification of punching shear outside the shear cap by the direct method
PublicationThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
FE-simulations of a direct and a true simple shear test
PublicationPorównano dwa aparaty ścinania: aparat bezpośredniego ścinania i aparat prostego ścinania. Analizy pola naprężeń i odkształceń dokonano stosując metodę elementów skończonych i mikropolarne prawo hypoplastyczne. Analiza ta pokazała, że pole naprężeń i odkształceń jest niejednorodne w obu aparatach, szczególnie w aparacie bezpośredniego ścinania.
-
FE-simulations of a direct wall shear box test.
PublicationW artykule przedstawiono wyniki numerycznej anlizy lokalizacji odkształceń stycznych w materiałach granulowanych podczas bezposredniego ścinania przy ścianie. Obliczenia przeprowadzono z mikropolarnym modelem hipoplastycznym. Obliczenia wykonano w płaskim stanie odkształcenia stosując metodę elementów skończonych. Wyniki numeryczne porównano z wynikami doświadczalnymi.
-
FE-simulations of a direct and a true simple shear test within a polar hypoplasticity
PublicationW artykule przedstawiono wyniki numerycznej analizy testu bezpośredniego ścinania i testu prostego ścinania w materiałach granulowanych. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. W analizie uwzględniono lokalizację odkształceń stycznych.
-
Inflow of fly ash on selected geotechnical parameters of soft soils.
Open Research DataThe reaserch presents the experimental results made on samples of soft soils mixed with fly ash in different proportions (10%, 20%, 30%). The files contains the data directly from direct shear aparatus and oedometer.
-
Direct design of Controlled Modulus Columns (CMC) based on in-situ testing
PublicationIn this paper, the serviceability limit state and bearing capacity of tension screw displacement piles were analyzed using the results of static pile load tests, carried out on the test plot near the Elbląg city, and field, and laboratory tests. The paper presents the methodology of determining the pile load-settlement curve using different types of t-z transfer functions. The new method of constructing the pile load-settlement...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublicationThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublicationThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Influence of Soft Soil Samples Quality on the Compressibility and Undrained Shear Strength – Seven Lessons Learned From the Vistula Marshlands
PublicationThis technical article presents the influence of sample quality on the compressibility parameters and undrained shear strength ( c u ) of soft soils from the Vistula Marshlands. The analysis covers: (1) quality of soft soil according to three criteria: void ratio (Δ e / e 0 index), volumetric strain (Δ ɛ v ) and C r / C c ratio; (2) influence of storage time on quality; (3) influence of sample quality on undrained shear strength...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublicationCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
Interlaboratory Test to Characterize the Cyclic Behavior of Bituminous Interlayers: An Overview of Testing Equipment and Protocols
PublicationThe performance assessment of multi-layered pavements strongly depends on the mechanical behavior of the interface between bituminous layers. So far, comprehensive studies have been carried out mainly using quasi-static laboratory tests focusing on the interlayer shear strength at failure. However, it is generally recognized that cyclic shear testing will lead to the determination of parameters which are more closely linked to...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublicationAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Comparative 3D DEM simulations of sand–structure interfaces with similarly shaped clumps versus spheres with contact moments.
PublicationThree-dimensional simulations of a monotonic quasi-static interface behaviour between initially dense cohesionless sand and a rigid wall of different roughness during tests in a parallelly guided direct shear test under constant normal stress are presented. Numerical modelling was carried out by the discrete element method (DEM) using clumps in the form of convex non-symmetric irregularly shaped grains. The clumps had an aspect...
-
Nano soil improvement technique using cement
PublicationNano soil-improvement is an innovative idea in geotechnical engineering. Nanomaterials are among the newest additives that improve soil properties. Herein, laboratory tests, such as unconfined compressive strength, direct shear test, and initial tests, were conducted to investigate the geotechnical properties of Kelachay clay with micro- and nanosized cement to evaluate its particles in untreated soil and observe changes in the...
-
A Generalized Framework Towards Structural Mechanics of Three-layered Composite Structures
PublicationThree-layered composite structures find a broad application. Increasingly, composites are being used whose layer thicknesses and material properties diverge strongly. In the perspective of structural mechanics, classical approaches to analysis fail at such extraordinary composites. Therefore, emphasis of the present approach is on arbitrary transverse shear rigidities and structural thicknesses of the individual layers. Therewith...
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublicationThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Load introduction to composite columns revisited—Significance of force allocation and shear connection stiffness
PublicationThe AISC 360-16 Specification recommends that the design shear force between parts of a composite column in the load introduction area shall be calculated based on the force allocation at ultimate limit state. Applicability of this straightforward method to the load levels that usually arise in slender composite columns is questionable, as this capacity-based force allocation is only true when the axial force is equal to the plastic...
-
Identification of Shear Modulus Parameters of Half-space Inhomogeneous by Depth
PublicationThe paper propose a method for determining of the parameters of the exponential shear modulus of a functionally graded half-space based on the solution of the problem of a pure shear of an elastic functionally graded half-space by a strip punch. The solution of the integral equation of the contact problem is constructed by asymptotic methods with respect to the dimensionless parameter. The dependence of contact stresses on the...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublicationThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Verification of Selected Calculation Methods Regarding Shear Strength in Reinforced and Prestressed Concrete Beams
PublicationThe purpose of this article was an attempt to compare selected calculation methods regarding shear strength in reinforced and prestressed concrete beams. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008 [1], ACI 318- 14 [2] and fib Model Code for Concrete Structures 2010 [3]. The analysis also consists of methods published in technical literature. Calculations of shear strengths were made based...
-
The Influence of Shear Deformation in analysis of plane frames
PublicationThe focus of the paper is to investigate the influence of shear deformation effect on the distribution of internal forces and frame deformation. To estimate shear deformation effect, the Timoshenko beam theory and the concept of shear deformation coefficients are used. Analysis of example frames gives the possibility to evaluate what have the most impact on size of shear deformation and in which type of frames the shear deformation...
-
Verification of selected calculation methods regarding shear strength in beams without web reinforcement
PublicationThe purpose of the article was to compare selected calculation methods regarding shear strength in reinforced concrete beams without web reinforcement. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008, ACI 318-14 and fib Model Code for Concrete Structures 2010. The analysis also consists of authorial methods published in technical literature. Calculations of shear strengths were made based on experimental...
-
Shear resistance of low height precast concrete lintels
PublicationThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Characterization of the Functionally Graded Shear Modulus of a Half-Space
PublicationIn this article, a method is proposed for determining parameters of the exponentialy varying shear modulus of a functionally graded half-space. The method is based on the analytical solution of the problem of pure shear of an elastic functionally graded half-space by a strip punch. The half-space has the depth-wise exponential variation of its shear modulus, whose parameters are to be determined. The problem is reduced to an integral...
-
Possible effects of the 1984 St. Clair River ice jam on bed changes
PublicationThis study examines the possible effect of the record ice jam of 1984 in the St. Clair River on river bed changes and conveyance. Numerical simulations were made to examine the flow and bed shear stresses during the jam formation and release periods. Simulation results indicate that the ice jam in the river did not cause a significant increase in bed shear stress compared to pre- and post-jam open water conditions. The insignificant...
-
Determination of Changes in Viscosity of Hydrogel Depending on Shear Rates
PublicationThe datasets entitled Determination of changes in viscosity of hydrogel depending on shear rate contain the results of viscosity measurements using a Brookfield viscometer, with different kinds of spindles and shear rates. The data allowed the used hydrogel preparations to be characterised and their functional parameters, as substances modifying the rheology of thickeners and determining the effect of shear rate on the viscosity...
-
Simulations of Shear Zones and Cracks in Engineering Materials Using eXtended Finite Element Method
PublicationNumerical simulations of cracks and shear zones in quasi-brittle materials are presented. Extended Finite Element Method is used to describe both cracks and shear zones. In a description of tensile cracks, a Rankine criterion is assumed. A discrete Mohr-Coulomb law is adopted for simulations of shear zones. Results of simple numerical tests: unixial tension, bending and biaxial compression are demonstrated.
-
Acoustic Heating Produced in the Thermoviscous Flow of a Shear-Thinning Fluid
PublicationThis study is devoted to the instantaneous acoustic heating of a shear-thinningfluid. Apparent viscosity of a shear-thinning fluid depends on the shear rate. Thatfeature distinguishes it from a viscous Newtonian fluid. The special linear combi-nation of conservation equations in the differential form makes it possible to derivedynamic equations governing both the sound and non-wave entropy mode inducedin the field of sound. These...
-
Temperature influences on shear stability of a nanosize plate with piezoelectricity effect
PublicationPurpose The purpose of this paper is to predict the mechanical behavior of a piezoelectric nanoplate under shear stability by taking electric voltage into account in thermal environment. Design/methodology/approach Simplified first-order shear deformation theory has been used as a displacement field. Modified couple stress theory has been applied for considering small-size effects. An analytical solution has been taken into account...
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublicationCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublicationPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublicationIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
Investigations on strength and fracture in RC beams scaled along height or length
PublicationThe objective of the present paper is to identify experimentally and theoretically differing failure mechanisms in reinforced concrete beams subjected to four-point bending for a separate variation of the depth and length at the constant thickness. Experiments were performed on reinforced concrete beams under four-point bending. Different failure mechanisms included steel yielding, diagonal tension or shear- compression depending...
-
Influence of addition of carbon nanotubes on rheological properties of selected liquid lubricants - a computer simulation study
PublicationThis work is motivated by the improvement of anti-friction properties of lubricants by addition of CNTs proved experimentally in literature. In particular, a methodology is developed to compute the shear viscosity of liquid lubricants (Propylene Glycol) based on Molecular Dynamics simulation. Non-Equilibrium molecular dynamics (NEMD) approach is used with a reactive force field ReaxFF implemented in LAMMPS. The simulations are...
-
Analyses of Shear Angle in Orthogonal Cutting of Pine Wood
PublicationThe determination of energy effects for wood machining processes, such as cutting power and cutting forces, is very useful in designing of manufacture process of wooden products. A more accurate prediction of cutting forces requires a correct determination of the shear angle value, which can be determined using various models. In this article, shear angle values for an orthogonal linear cutting process of pine wood are determined. The...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublicationThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublicationIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
Equivalent Single Layer Models in Free Vibration Analysis of Laminated Multi-Layered Plates
PublicationThe performance of selected equivalent single-layer (ESL) models is evaluated within several classical benchmark tests for small amplitude free vibration analysis of multi-layered plates. The authors elaborated their own Finite Element software based on the first-order shear deformation (FOSD) theory with some modifications incorporated including a correction of the transverse shear stiffness and an application of zigzag type functions....