Search
Filters
total: 135
Search results for: RESONANT FREQUENCY
-
A Self-Equalized Waveguide Filter With Frequency-Dependent (Resonant) Couplings
PublicationThis letter presents a design of a fifth-order linear phase filter with frequency-dependent couplings. The filter is composed of a triplet that is directly coupled to two resonators at the input and output. To provide group delay flattening a cross-coupling in the trisection has a strongly dispersive character with a negative slope parameter. To achieve this, an E-plane stub with a septum was used. To further improve the filter...
-
Prediction of Ship Resonant Rolling - Related Dangerous Zones with Regard to the Equivalent Metacentric Height Governing Natural Frequency of Roll
PublicationPotentially dangerous zones corresponding to dynamical stability phenomena, possibly encountered by ships sailing in rough sea, are estimated nowadays with the use of the method recommended by IMO in the guidance coded MSC.1/Circ.1228. In this IMO method the parameter governing the natural period of roll is the initial metacentric height. Some earlier studies revealed that the initial metacentric height...
-
Resonant ultrasonic spectroscopy in high-voltage varistor spectroscopy
PublicationResonant spectroscopy is an effective non-destructive testing method focused on defects in tested objects. The testing procedure, based on the resonant pattern, allows rejection of the tested samples with defects which do not fit the pattern. A sweeping frequency method has been used to measure the spectrum of resonances in high-voltage varistors. As a result we can observe resonances that depend directly on inhomogeneity of the...
-
Fast bubble dynamics and sizing
PublicationSingle bubble sizing is usually performed by measuring the resonant bubble response using the Dual Frequency Ultrasound Method. However, in practice, the use of millisecond-duration chirp-like waves yields nonlinear distortions of the bubble oscillations. In comparison with the resonant curve obtained under harmonic excitation, it was observed that the bubble dynamic response shifted by up to 20 percent of the resonant frequency...
-
Non-isolated resonant quasi-Z-source network DC–DC converter
PublicationA novel non-isolated resonant quasi-impedance (quasi-Z)-source network DC–DC converter is proposed. The resonant impedance source network is derived from the quasi-Z-source network by including the autotransformer-based resonant cell instead of the second inductor of the quasi-Z-network. The leakage inductance of the autotransformer and two resonant capacitors connected in series with the autotransformer windings constitute a high-frequency...
-
Diagnostics of high-voltage varistor quality using resonant ultrasound spectroscopy
PublicationResonant spectroscopy is an effective nondestructive testing method focused on defects detection in tested objects. Resonance spectrum contains an information about the mechanical properties and particularly about the structural homogeneity of the whole object. A swept frequency method has been used to measure the selected resonant frequencies range. The system for measurement of resonant ultrasound spectroscopy of high-voltage...
-
Resonant Frequencies in Microstrip Structure with Omega Medium Substrate
PublicationThe paper presents the research on a rectangular microstrip structure with multilayer substrate containing dielectric and omega medium layers. The effect of pseudochiral medium layer location in the substrate and its thickness on the resonant frequency of the rectangular microstrip structure is investigated. The numerical analysis of investigated structures is based on expansion of electric and magnetic fields. Utilizing the continuity...
-
Automatic tuning of a resonant circuit in wireless power supply systems for biomedical sensors
PublicationIn this paper, a tuning method of a resonant circuit suited for wireless powering of miniature endoscopic capsules is presented and discussed. The method allows for an automatic tuning of the resonant frequency and matching impedance of a full wave rectifier loading the resonant circuit. Thereby, the receiver tunes so as to obtain the highest power efficiency under given conditions of transmission. A prototype receiver for wireless...
-
Substrate Integrated Waveguide-Based Frequency-Tunable Self-Octaplexing Antenna
PublicationThis communication presents the first-ever substrate integrated waveguide (SIW)-based frequency-tunable self-octaplexing antenna (SOA) for wireless communication. The structure is arranged by implementing eight distinct patches with planar 50-ohm feedlines at the top of the SIW cavity, which realize eight distinct resonant frequencies. Independent tuning of each resonant frequency is achieved by incorporating appropriately allocated...
-
Errors in the analysis of series resonant inverter/converter assuming sinusoidal waveforms of voltage and current
PublicationIn this paper the theory and simulation results of the series resonant inverter / converter are presented. In this work the authors carried out a detailed comparative analysis of results obtained using the method of AC analysis in the steady state for the first harmonic with the results of computer simulation. The AC analysis under certain conditions can lead to errors disqualifying this method. In particular, these errors appear...
-
Accurate design of pseudoelliptic inline SIW filters with frequency-dependent couplings
PublicationThis paper presents an accurate synthesis method for inline SIW (Substrate Integrated Waveguide) generalized Chebyshev bandpass filters with frequency-dependent couplings. The technique is based on the synthesis of a coupling matrix that takes into account the impedance of the frequency-dependent stub. Thus, a loading effect compensation in adjacent resonators (via resonant frequency adjustment) and coupling elements (via coupling-value...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublicationUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
-
A Substrate Integrated Waveguide (SIW) Bandpass Filter in A Box Configuration With Frequency-Dependent Coupling
PublicationThis letter presents the design of a microwave bandpass filter with frequency-dependent coupling implemented in substrate integrated waveguide (SIW) technology. The proposed filter implements a four-pole generalized Chebyshev filtering function with two transmission zeros. Resonators are arranged in an extended box configuration with dispersive coupling on a main signal path, which produces an extra zero in comparison to classical...
-
On ship roll resonance frequency
PublicationThe paper deals with the problem of modeling of rolling motion under a variety of excitation parameters. Special emphasis is put on the analysis and prediction of the frequency of the resonant mode of rolling, since it is often an essential issue in terms of motion of a ship related to her safety against capsizing or excessive amplitudes of roll. The research is performed for both free rolling and excited rolling and it is based...
-
A Novel Coupling Matrix Synthesis Technique for Generalized Chebyshev Filters With Resonant Source–Load Connection
PublicationThis paper reports a novel synthesis method for microwave bandpass filters with resonant source–load connection. In effect, a network realizing N+1 transmission zeros (where N is the number of reflection zeros) is obtained. The method is based on a prototype transversal coupling matrix (N+2, N+2) with source and load connected by a resonant circuit formed by a capacitor in parallel with a frequency-invariant susceptance. To complement...
-
WARUNKI REZONANSOWE W WĘŹLE Z KOMPENSATOREM SVC
PublicationInstalowanie kompensatorów statycznych w sieciach rozdzielczych i przesyłowych służy poprawie profili napięciowych. Kompensatory jako źródła mocy biernej zwiększają stabilność napięciową systemu. Pozwalają także na szybszą odbudowę systemu w przypadku awarii napięciowej. W artykule zaprezentowano wpływ struktury i wysterowania układu SVC na zmianę impedancji w układzie zasilania. Ma to bezpośredni wpływ na częstotliwości, przy...
-
Development of a compact microstrip resonant cell aimed at efficient microwave component size reduction
PublicationA comprehensive comparison of a wide collection of compact microstrip resonant cells (CMRCs) found in the extensive body of literature has been presented. The evaluation of different CMRC designs has led to the selection of the most promising CMRC geometry for the efficient miniaturisation of modern microwave components. In order to showcase the vital effectiveness of the approach, the initially selected CMRC has been notably...
-
Resonance in Rectangular Microstrip Structure Loaded with a Pseudochiral Medium Layer
PublicationA rectangular microstrip structure with multilayer substrate containing dielectric and pseudochiral medium layers is studied in this paper. The effect of Omega medium layer location in the substrate and its thickness on the complex resonant frequency of the rectangular microstrip structure is investigated.
-
Frequency-Reconfigurable Hybrid SIW-Based Self-Diplexing Antenna Using Solid and Liquid Dielectric Loading
PublicationThis paper presents a novel frequencyreconfigurable self-diplexing antenna (SDA) utilizing a hybrid substrate-integrated waveguide (SIW). The antenna comprises a radiating slot, a feeding network, and a hybrid SIW cavity featuring half-mode circular and half-mode rectangular SIW structures. The unique feature of this antenna lies in its fine-tuning capability of each resonant frequency by inserting or injecting solid and liquid...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Classification of high-voltage varistors into groups of differentiated quality
PublicationThe research was aimed on defining a factor of quality for high-voltage varistors using Non-Destructive Testing (NDT) techniques, which could be applied during the production testing. The newly proposed parameter Q determined on the basis of the lowest resonant frequency fr measured within the preselected frequency range was taken into account. The parameter Q was defined for ZnO structures after firing, without metallized contacts....
-
Microfluidic SIW-Based Tunable Self-Diplexing Antenna for Sub-6 GHz Band Applications
PublicationThis work introduces a novel frequency tunable self-diplexing antenna (SDA) design based on substrate integrated waveguide (SIW) technology. A modified A-shaped slot is employed on the cavity’s top plane, which is excited by two independent 50 Ω microstrip feed lines to operate at each resonant frequency. The frequency flexibility of the proposed antenna allows for fine-tuning at each resonance frequency. The frequency flexibility...
-
Shielded HMSIW-based frequency-tunable self-quadruplexing antenna using different solid/liquid dielectrics
PublicationThis article proposes a frequency-tunable self-quadruplexing antenna based on a shielded half-mode substrate integrated waveguide (S-HMSIW). In order to reduce the size of the HMSIW cavity resonator and to obtain quad-band characteristics, a modied E-shaped slot is engraved on the top of the metal. The experimental validation is carried out after analyzing the data using a circuit model. Flexibility of each resonant frequency is...
-
A novel microstrip dual-layer rat-race coupler with compact size and enhanced bandwidth
PublicationMicrowave hybrid couplers are crucial components of mixers, phase shifters, amplifiers and other high-frequency systems. Conventional couplers are characterized by large size which limits their usefulness in modern applications. In this work, a novel compact rat-race coupler with enhanced bandwidth has been proposed. The structure consists of six compact microstrip resonant cells. It is implemented on two separate layers which permits...
-
Efficient Analysis of Noise Induced in Low-Voltage Installations Placed Inside Buildings with Lightning Protection Systems
PublicationThis paper describes an efficient approach to the broadband analysis of lightning protection systems (LPSs) using the method of moments (MoM) implemented in the frequency domain. The adaptive frequency sampling (AFS) algorithm, based on a rational interpolation of the relevant observable (e.g., voltage, current, electric or magnetic field) which describes the properties of the LPS, is employed to reduce the number of samples computed...
-
SiC-based phase-shift dual half bridge DC-DC converter as a key component of multilevel cascaded MV converters
PublicationThe paper describes SiC-based dual half bridge (DHB) DC-DC converter considered as a key component of high frequency isolated multilevel cascaded medium voltage converters. Two topologies of bi-directional DC-DC converters: the resonant half-bridge DC-DC converter and the phase-shift DHB converter are compared in the paper. Experimental results of SiC-based 50 kHz DHB DC-DC converter are presented in the paper.
-
A Low-Profile Metal-backed Dipole Loaded with Closely Coupled Arc-shaped Open Stubs for On-metal Tag Design with Wide Frequency Tuning Capability
PublicationThis research has presented a single-layer metal-backed dipole antenna, which consists of a feedline loaded with two pairs of closely-coupled arc-shaped open stubs, for designing a metal-mountable tag that features tuning capability over a wide range of frequency. Here, the stubs can generate sufficient inductive reactance for bringing down the tag resonant frequency tunable in both the regulated UHF RFID passbands (North American...
-
Metamaterial-Based Sub-Microwave Electromagnetic Field Energy Harvesting System
PublicationThis paper presents the comprehensive analysis of the sub-microwave, radio frequency band resonant metastructures’ electromagnetic properties with a particular emphasis on the possibility of their application in energy harvesting systems. Selected structures based on representative topologies of metamaterials have been implemented in the simulation environment. The models have been analyzed and their substitute average electromagnetic...
-
Development and Assessment of Regeneration Methods for Peptide-Based QCM Biosensors in VOCs Analysis Applications
PublicationCleaning a quartz crystal microbalance (QCM) plays a crucial role in the regeneration of its biosensors for reuse. Imprecise removal of a receptor layer from a transducer’s surface can lead to unsteady operation during measurements. This article compares three approaches to regeneration of the piezoelectric transducers using the electrochemical, oxygen plasma and Piranha solution methods. Optimization of the cleaning method allowed...
-
Accurate Modeling of Frequency Selective Surfaces Using Fully-Connected Regression Model with Automated Architecture Determination and Parameter Selection Based on Bayesian Optimization
PublicationSurrogate modeling has become an important tool in the design of high-frequency structures. Although full-wave electromagnetic (EM) simulation tools provide an accurate account for the circuit characteristics and performance, they entail considerable computational expenditures. Replacing EM analysis by fast surrogates provides a way to accelerate the design procedures. Unfortunately, modeling of microwave passives is a challenging...
-
Hybrid piezoelectric motor based on electroactive lubrication principle
PublicationA novel conception of hybrid piezoelectric motor is presented in this paper. Proposed conception required synchronised work of quasi-static and resonant piezoelectric actuators that results in a rotary movement. The motor's working principle is explained and the main characteristics are described. Studied topology is compared to the existing piezoelectric motors with regards to its field of applications. The assembling process...
-
Design of Microwave-Based Angular Displacement Sensor
PublicationThis letter presents a novel microwave-based rotation sensor having a wide dynamic range to detect and measure the angular displacement in terms of the change in resonant frequency. The proposed sensor is based on the microstrip technology, where a rotor comprised of a complementary splitring resonator (CSRR) placed on the ground plane of the microstrip line is free to rotate around its axis. The mechanical rotation of CSRR determines...
-
Microwave Ring Resonator Based Pressure Sensor
PublicationThis paper demonstrates a microwave pressure sensor, which is based on microstrip line-fed ring resonators. The first ring resonator is loaded with the concentric cylindrical shafts, while the same number of the hollow shanks as the shafts are mounted on the second ring resonator. The arrangement of the cylindrical shaft and hollow shank allows for mechanical movement between two substrates while maintaining electrical contact....
-
Efficient model order reduction for FEM analysis of waveguide structures and resonators
PublicationAn efficient model order reduction method for three-dimensional Finite Element Method (FEM) analysis of waveguide structures is proposed. The method is based on the Efficient Modal Order Reduction (ENOR) algorithm for creating macro-elements in cascaded subdomains. The resulting macro-elements are represented by very compact submatrices, leading to significant reduction of the overall number of unknowns. The efficiency of the model...
-
Multi-transformer primary-side regulated flyback converter for supplying isolated IGBT and MOSFET drivers
PublicationThis paper presents primary-side voltage regulated multi-transformer quasi-resonant flyback converter (MTFC) for supplying isolated power switch drivers. The proposed topology offers distinct advantages over frequently used flyback converter possessing one high frequency transformer with isolated multiple outputs. Particularly, when a large number of separate dc supply units is required, then MTFC enables improved regular distribution...
-
Uncertainty Quantification of Additive Manufacturing Post-Fabrication Tuning of Resonator-Based Microwave Sensors
PublicationReconfigurability, especially in terms of the ability of adjusting the operating frequency, has become an important prerequisite in the design of modern microwave components and systems. It is also pertinent to microwave sensors developed for a variety of applications such as characterization of material properties of solids or liquids. This paper discusses uncertainty quantification of additive-manufacturing-based post-fabrication...
-
Ultrasonic spectroscopy of silicon single crystal
PublicationSpecimens of Si single crystals with different crystal orientation [100] and [110] were studied by the electro-ultrasonic spectroscopy (EUS) and Resonant Ultrasonic Spectroscopy (RUS). A silicon single crystal is an anisotropic crystal, so its properties are different in different directions in the material relative to the crystal orientation. EUS is based on interaction of two signals: electric AC signal and ultrasonic signal,...
-
Badania eksperymentalne rezonansowego przetwornika piezoelektrycznego typu "unimorph"
PublicationW artykule opisano badania eksperymentalne piezoelektrycznego rezonansowego przetwornika zastosowanego do pomiaru właściwości mechanicznych tkanek miękkich. Po krótkim wstępie w kolejnych punktach przedstawiono opis stanowiska pomiarowego oraz metody pomiaru odkształceń prototypów, przesunięć częstotliwości rezonansowej, impedancji elektromechanicznej i parametrów schematów zastępczych. W dalszej...
-
Compact Substrate-Integrated Hexagonal Cavity-Backed Self-Hexaplexing Antenna for Sub-6 GHz Applications
PublicationA self-multiplexing SIW antenna based on hexagonal SIW cavity is proposed. The self-hexaplexing antenna consists of different sizes of resonating elements, which provide the hexaband operations. The antenna resonates at 5 GHz, 5.17 GHz, 5.32 GHz, 5.53 GHz, 5.62 GHz, and 5.72 GHz by employing different slot lengths between the resonating elements. The proposed antenna provides the individual tunable characteristics of the operating...
-
Millimeter Wave Negative Refractive Index Metamaterial Antenna Array
PublicationIn this paper, a novel negative refractive index metamaterial (NIM) is developed and characterized. The proposed metamaterial exhibits negative effective permittivity (εeffe) and negative effective permeability (µeffe) at millimeter wave frequency of 28GHz. This attractive feature is utilized to enhance the gain of a microstrip patch antenna (MPA). Two thin layers of 5 5 subwavelength unit cell array of NIM are placed above a...
-
PREDICTION OF SHIP MOTIONS IN IRREGULAR WAVES BASED ON RESPONSE AMPLITUDE OPERATORS EVALUATED EXPERIMENTALLY IN NOISE WAVES
PublicationThe most common methods for predicting ship roll motions in a specified sea state are direct measurements of motions in a representative irregular wave realisation (time domain) or calculations of motions from response amplitude operators (RAOs) in the frequency domain. The result of the first method is valid only for the tested sea state, whilst the second method is more flexible but less accurate. RAO-based predictions are calculated...
-
Inverse Modeling and Optimization of CSRR-based Microwave Sensors for Industrial Applications
PublicationDesign optimization of multivariable resonators is a challenging topic in the area of microwave sensors for industrial applications. This paper proposes a novel methodology for rapid re-design and parameter tuning of complementary split-ring resonators (CSRRs). Our approach involves inverse surrogate models established using pre-optimized resonator data as well as analytical correction techniques to enable rapid adjustment of geometry...
-
Planar Microwave Bragg Reflector Resonant Dielectric Sensor
PublicationIn this paper, a periodic structure is used to design a microwave Bragg reflector with the help of hexagonal lattice, which provides a 5 GHz wide stopband between the low-pass band with cut-off frequency 2.6 GHz and the bandpass response with start and stop frequency 7.8 GHz and 10.5 GHz, respectively. A defect in lattice allows passing a narrowband signal at 6 GHz which is found, from the dispersion relation, to be in the region...
-
Modal FEM Analysis of Ferrite Resonant Structures
PublicationThe finite-element method (FEM) is applied for modal analysis of ferrite-loaded spherical resonators. To improve the efficiency of the numerical calculations, the body-of-revolution (BOR) technique is utilized. Due to the frequency-dependent ferrite permeability, FEM leads to a nonlinear eigenvalue problem that is challenging to solve. To this end, Beyn’s method is proposed. The effectiveness of the proposed approach is confirmed...
-
Examples of AFM applications in liquid environment
Open Research DataImportant advantage of atomic force microscopy (also tunneling microscopy) is the ability to work in different environments (vacuum, controlled atmosphere, liquid environment). The last one, open interesting possibilities, such as imaging of delicate biological materials in their natural state. The use of electrochemical mode allows for the modification...
-
A Low-Profile 3-D Printable Metastructure for Performance Improvement of Aperture Antennas
PublicationIn order to increase the radiation performance of aperture-type antennas, this paper demonstrates a low-profile, planar, single-layer, three-dimensional (3-D) printable metastructure. The proposed hybridized metastructure is highly transparent as it is made out of novel hybrid meta-atoms having transmission coefficient magnitudes greater than -0.72 dB and fully complies with the near-field phase transformation principle. The hybridized...
-
Analysis of nonlinear eigenvalue problems for guides and resonators in microwave and terahertz technology
PublicationThis dissertation presents developed numerical tools for investigating waveguides and resonators' properties for microwave and terahertz technology. The electromagnetics analysis requires solving complex eigenvalue problems, representing various parameters such as resonant frequency or propagation coefficient. Solving equations with eigenvalue boils down to finding the roots of the determinant of the matrix. At the beginning, one...
-
Modeling of free vibrations and resonant frequencies of simply-supported submerged horizontal plate
PublicationA theoretical approach was applied to study the vibration of simple-supported submerged horizontal plate. The derived analytical solution was used to determine natural frequencies for a horizontal plate vibrating in fluid. The investigations were conducted for a very wide range of material density and elasticity modulus covering all materials used in engineering practice. Analysis shows that plate vibration frequency decreases...
-
On Rapid Design Optimization and Calibration of Microwave Sensors Based on Equivalent Complementary Resonators for High Sensitivity and Low Fabrication Tolerance
PublicationThis paper presents the design, optimization, and calibration of multivariable resonators for mi-crowave dielectric sensors. An optimization technique for circular complementary split ring reso-nator (CC-SRR) and square complementary split ring resonator (SC-SRR) is presented to achieve the required transmission response in a precise manner. The optimized resonators are manufac-tured using a standard photolithographic technique...
-
Identification of the mechanical properties of the skin by electromechanical impedance analysis of resonant piezoelectric actuator
PublicationThis paper is devoted to the analysis and verification of developed piezoelectric sensor/actuator for measuring the mechanical properties of soft tissues, especially human skin. The key element of the measurement structure is an electromechanical system that uses both the reverse piezoelectric effect (vibration generation – stimulation of the tissues in the appropriate frequency range) and direct piezoelectric effect (system response...