Search
Filters
total: 233
Search results for: dynamic sampling
-
Dynamic Headspace Sampling as an Initial Step for Sample Preparation in Chromatographic Analysis
PublicationThis work represents a brief summary of the use of dynamic headspace (DHS) as a technique for sample preparation in chromatographic analysis. Despite numerous developments in the area of analyte isolation and enrichment, DHS remains one of the fundamental methods used with GC. In our opinion, interest in this technique will not diminish significantly because it conforms to stipulations of green analytical chemistry. Moreover, DHS...
-
Green Sample Collection
PublicationThe term of “green sample collection” is directly associated with both passive and dynamic analytical tools which allow for simultaneous management of the stage of collection and isolation and/or enrichment of a broad spectrum of chemical compounds from environmental samples. The use of passive sampling techniques at the stage of sample collection makes it possible to obtain in a simple yet inexpensive manner an analytical information...
-
Employment of passive sampling in monitoring indoor air quality in selected residences in a Tri-city area in Poland
PublicationTime-weighted average concentrations of selected volatile compounds were measured in chosen residences in a Tri-City area of Poland by means of passive sampling. The results were compared to those obtained by dynamic technique – sorption tubes filled with Tenax TA sorbent. Results obtained by employing the two techniques were similar. Total volatile organic compound (TVOC) parameters were also determined. An attempt was also...
-
Determination of Volatile Organic Compounds in Indoor Air in the Gdansk Area Using Permeation Passive Samplers
PublicationPassive dosimetry — known for over a hundred years — is still a useful tool in monitoring air pollutants. In this work, permeation passive samplers were used to determine indoor air quality in 22 apartments located in the Gdansk area in the northern part of Poland. The results obtained by the passive sampling technique were compared to those obtained by dynamic sampling. Attempts were also made to identify indoor sources of...
-
Monitoring of volatile organic compounds (VOCs) in atmospheric air. Part II. Sample collection and preparation
PublicationThe paper reviews literature information on air sampling techniques commonly used for monitoring volatile organic compounds (VOCs) levels in atmospheric air. It describes containers for collecting samples of atmospheric air, such as vacuum canisters and bags made from synthetic materials. It discusses dynamic, passive and denudational techniques for sampling analytes from air combining isolation with preliminary enrichment, and...
-
Sliding friction of alumina (Al2O3) with friction induced vibrations
Open Research DataTest files containing data on experiments in self mated sliding contact of alumina Al2O3 lubricated with either water or paraffin oil. Tests run in variable load/velocity conditions and with different dynamic settings of the test rig (PT-3 tribometer). The aim of the research was to attempt in finding correlations between the dynamic characteristics...
-
Online Volatile Compound Emissions Analysis Using a Microchamber/Thermal Extractor Coupled to Proton Transfer Reaction-Mass Spectrometry
PublicationIndoor air is a complex and dynamic mixture comprising manifold volatile organic compounds (VOCs) that may cause physiological and/or psychological discomfort, depending on the nature of exposure. This technical note presents a novel approach to analyze VOC emissions by coupling a microchamber/thermal extractor (μ-CTE) system to a proton transfer reaction-mass spectrometer (PTR-MS). This configuration provides an alternative to...
-
Evaluating Performance and Accuracy Improvements for Attention-OCR
PublicationIn this paper we evaluated a set of potential improvements to the successful Attention-OCR architecture, designed to predict multiline text from unconstrained scenes in real-world images. We investigated the impact of several optimizations on model’s accuracy, including employing dynamic RNNs (Recurrent Neural Networks), scheduled sampling, BiLSTM (Bidirectional Long Short-Term Memory) and a modified attention model. BiLSTM was...
-
A Universal Gains Selection Method for Speed Observers of Induction Machine
PublicationProperties of state observers depend on proper gains selection. Each method of state estimation may require the implementation of specific techniques of finding those gains. The aim of this study is to propose a universal method of automatic gains selection and perform its verification on an induction machine speed observer. The method utilizes a genetic algorithm with fitness function which is directly based on the impulse response...
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublicationCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
AeroSense Measurements: Wind Tunnel Ecole Centrale Lyon
Open Research DataData from wind tunnel tests of Aerosesne measurement system installed on NACA 63418 aerfoil in the anechoic wind tunnel at the Ecole Centrale Lyon.
-
Performance Analysis of Machine Learning Methods with Class Imbalance Problem in Android Malware Detection
PublicationDue to the exponential rise of mobile technology, a slew of new mobile security concerns has surfaced recently. To address the hazards connected with malware, many approaches have been developed. Signature-based detection is the most widely used approach for detecting Android malware. This approach has the disadvantage of being unable to identify unknown malware. As a result of this issue, machine learning (ML) for detecting malware...
-
Sampling Strategies: Statistics of Sampling
PublicationEach step of the analytical procedure has a significant influence on the final result of the analysis. In the majority of cases the analytical procedure encompasses sampling because the analysis of the entire object (material) is usually not possible. Thus it is necessary to include the uncertainty related to sampling procedure in the uncertainty budget calculations. In the paper: the most important properties of the analysed...
-
Adaptive Sampling for Non-intrusive Reduced Order Models Using Multi-Task Variance
PublicationNon-intrusive reduced order modeling methods (ROMs) have become increasingly popular for science and engineering applications such as predicting the field-based solutions for aerodynamic flows. A large sample size is, however, required to train the models for global accuracy. In this paper, a novel adaptive sampling strategy is introduced for these models that uses field-based uncertainty as a sampling metric. The strategy uses...
-
The Application of a Mobile Unmanned Device for Monitoring Water and Sediment Pollution in the Port of Gdynia
PublicationPollution in the Port of Gdynia can encompass various types of substances and contaminants that affect the quality of water and sediment in this region. Ships entering and leaving the port can release pollutants such as oil, fuel, waste, and chemicals into the water. Controlling and monitoring these pollutants is a crucial part of environmental stewardship. In recent years, uncrewed units have been increasingly in use for in situ...
-
Validation of atmospheric aerosols sampling in equivalent fractions
PublicationPhysical properties and chemical composition of atmospheric aerosols are of extreme importance, in many fields of interest, namely the Environment even with legal implications. Atmospheric sampling poses inherent problems with consequent demands on sampling optimisation, with sampling strategies requiring validation. In this work a study was conducted aiming at validating the collection of atmospheric aerosols in equivalent fractions....
-
Validation of a sampling procedure
PublicationEach step of the analytical procedure influences the final results in a significant way. In the majority of cases the analytical procedure encompasses sampling because the analysis of the entire object (material) is usually not possible. Thus it is necessary to include the uncertainty related to sampling procedure in the uncertainty budget calculations. This paper describes two basic ways of estimating the sampling uncertainty,...
-
Passive sampling and/or extraction techniques in environmental analysis: a review
PublicationThe current state-of-the-art of passive sampling and/or extraction methods for long-term monitoring of pollutants in different environmental compartments is discussed in this review. Passive dosimeters that have been successfully used to monitor organic and inorganic contaminants in air, water, sediments, and soil are presented. The application of new approaches to the determination of pollutants at the sampling stage is discussed....
-
Sample preparation and recent trends in volatolomics for diagnosing gastrointestinal diseases
PublicationThe analysis of the human volatilome can be successfully used for rapid and non-invasive diagnostics of gastrointestinal diseases. However, the introduction of techniques based on detection of volatiles is limited, among other factors, by difficulties which arise during the sampling stage and instrumental analysis. The aim of this article was to review and discuss medical and analytical literature on the analysis of volatiles in...
-
Uniform sampling in constrained domains for low-cost surrogate modeling of antenna input characteristics
PublicationIn this letter, a design of experiments technique that permits uniform sampling in constrained domains is proposed. The discussed method is applied to generate training data for construction of fast replacement models (surrogates) of antenna input characteristics. The modeling process is design-oriented with the surrogate domain spanned by a set of reference designs optimized with respect to the performance figures and/or operating...
-
Indirect Measurement of Motor Current Derivatives in PMSM Sensorless Drives
PublicationMotor current derivatives contain useful information for control algorithms, especially in sensorless electric drives. The measurement of motor current derivatives in electric motors supplied by voltage source inverter can be performed using di/dt transducers. However, in such a solution additional sensors have to be installed, e.g. Rogowski coils. Another approach is to measure current derivatives indirectly – by oversampling...
-
Sampling Procedures in Studies of Cloud Water Composition: A Review
PublicationThe authors set out and classify the principles of operation of known types of cloud water collectors, and critically review their advantages and drawbacks. Analysis of the literature has yielded information on the parameters of various type of collectors—sampling time, the type of cloud from which the water sample was taken, droplet diameter collected with 50% efficiency (cut off), sample analytes/ parameters determined, types...
-
Unconventional and user-friendly sampling techniques of semi-volatile organic compounds present in an indoor environment: An approach to human exposure assessment
PublicationThe commonly applied solutions used to assess the potential risk of human exposure to semi-volatile organic compounds (SVOCs) are based on the investigation of biological samples collected in an invasive or non-invasive manner. For SVOCs, which are typically introduced to humans through the respiratory system, dermal adsorption, or digestive system, sampling solutions generally used in the indoor environments are classified as...
-
Assessment of baby disposable diapers application for urine collection and determination of phthalate metabolites
PublicationThe baby disposable diapers were investigated as a sampling material for urine collection and validated for the evaluation of the exposure of children to xenobiotics. Phthalate metabolites detected in urine samples were chosen as proof-of-concept analytes. For the determination of phthalate metabolites in children’s urine samples, high performance liquid chromatography coupled with tandem mass spectrometry (HPLC-MS/MS) was used. Two...
-
Improved Uniform Sampling in Constrained Domains for Data-Driven Modelling of Antennas
PublicationData-driven surrogate modelling of antenna structures is an attractive way of accelerating the design process, in particular, parametric optimization. In practice, construction of surrogates is hindered by curse of dimensionality as well as wide ranges of geometry parameters that need to be covered in order to make the model useful. These difficulties can be alleviated by constrained performance-driven modelling with the surrogate...
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublicationIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
Using A Particular Sampling Method for Impedance Measurement
PublicationThe paper presents an impedance measurement method using a particular sampling method which is an alternative to DFT calculation. The method uses a sine excitation signal and sampling response signals proportional to current flowing through and voltage across the measured impedance. The object impedance is calculated without using Fourier transform. The method was first evaluated in MATLAB by means of simulation. The method was...
-
Application of passive sampling techniques as a usable tool in the field of environmental quality monitoring
PublicationAnalysis of literature data published for the past 20 years leads to the conclusion, that passive sampling technique has been developing very quickly and is commonly used in the field of monitoring pollutants in air, water and soil environment. The popularity of application of passive sampling techniques in analytical and environmental chemistry results from its many advantages e.g.: Simplicity in use, low costs of exploitation,...
-
Continuous blood pressure monitoring by photoplethysmography - signal preprocessing requirements based on blood flow modelling
PublicationObjective. The aim of the study is to investigate the effect of the signal sampling frequency and low-pass filtering on the accuracy of the localisation of the fiducial points of the photoplethysmographic signal (PPG), and thus on the estimation of the blood pressure (i.e. the accuracy of the estimation). Approach. Statistical analysis was performed on 3,799 data samples taken from a publicly available database. Four PPGfiducial...
-
Effectiveness of Random Field Approach in Serviceability Limit State Analysis of Strip Foundation
PublicationThis work conducts a probabilistic inquiry on how the variability of the parameter defining soil deformability affects the settlement of the foundation located on the soil. The analysis addresses the random foundation model to relevantly estimate the probability of allowable deflection exceedance. The constitutive model parameter is based either on a single random variable or a random field. The computations incorporate direct...
-
Flexible Knowledge–Vision–Integration Platform for Personal Protective Equipment Detection and Classification Using Hierarchical Convolutional Neural Networks and Active Leaning
PublicationThis work is part of an effort to develop of a Knowledge-Vision Integration Platform for Hazard Control (KVIP-HC) in industrial workplaces, adaptable to a wide range of industrial environments. The paper focuses on hazards resulted from the non-use of personal protective equipment (PPE). The objective is to test the capability of the platform to adapt to different industrial environments by simulating the process of randomly selecting...
-
In-ADC, Rank-Order Filter for Digital Pixel Sensors
PublicationThis paper presents a new implementation of the rank-order filter, which is established on a parallel-operated array of single-slope (SS) analog-to-digital converters (ADCs). The SS ADCs use an “on-the-ramp processing” technique, i.e., filtration is performed along with analog-to-digital conversion, so the final states of the converters represent a filtered image. A proof-of-concept 64 × 64 array of SS ADCs, integrated with MOS...
-
Sensorless IPMSM drive with rotor position estimator based on analysis of phase current derivatives
PublicationThis paper describes a sensorless Interior Permanent Magnet Synchronous Motor (IPMSM) drive designed for traction applications. Wide-speed sensorless operation is provided with the use of three methods of rotor position estimation designed for: a standstill, low- and high-speed range. The paper focuses on the high-speed estimation algorithm. The estimator uses the derivatives of motor phase currentsresulting from PWM modulation...
-
Digital Processing of Frequency–Pulse Signal in Measurement System
PublicationThe work presents the issue of the use of multichannel measurement systems of sensors processing input value to impulse signal frequency. The frequency impulse signal obtained from such sensors is often required to be processed at the same time with a voltage signal which is obtained from other sensors used in the same measurement system. In such case, it is usually necessary to sample the output signals from all sensors in the...
-
Error analysis of calculating average d-q current components using Regular Sampling and Park transformation in FOC drives
PublicationIn electric drives using voltage source inverters, motor currents contain ripple component resulting from pulse-width modulated (PWM) voltage. The frequency range of the ripples is much higher than the bandwidth of current control. Therefore the control is performed on the basis of a fundamental current component, i.e. average value with the averaging time being the PWM period. In majority of cases the average current is measured...
-
Analytical modeling of electric drives for vehicle traction control systems
PublicationWheel-torque control bandwidth in vehicle dynamics model is crucial in evaluating optimal tracking ability of tire slip and in analysis of control system stability. Electric drives’ control dynamics are influenced by timing of digital control events, e.g. by sampling instant of motor currents. Reflecting this timing in drive analytical models is therefore important for analysis of vehicle traction systems. The paper considers five...
-
Particulate Material Analysis in Air
PublicationThe chapter presents the methods and techniques used to asses the PM10 in air and different instruments typically used in analysis of PM, including sampling of particle by using filters and other systems. Besides the methods recommended by different national standards the other methods, especially electronic microscopy are also described.
-
BEXUS 30 Stardust – Preliminary Results of Investigation of Microbes in the Stratosphere
PublicationThe stratospheric microbiome has been investigated several times using the methods of classical microbiology. In this experiment, we have combined them with some novel approaches.. Diversification of methods has helped better describe the collected microorganisms. The results of the experiment may help better understand the mechanisms of survivability of microorganisms in stratospheric conditions.
-
Derivation of motor mean phase currents in PMSM drives operating with low switching-to-fundamental frequency ratio
PublicationPulse width modulation (PWM) of inverter output voltage causes the waveforms of motor phase cur-rents to consist of distinctive ripples. In order to provide suitable feedback for the motor current con-trollers, the mean value must be extracted from the currents’ waveforms in every PWM cycle. A com-mon solution to derive the mean phase currents is to sample their value at the midpoint of a symmetrical PWM cycle. Using an assumption...
-
Ellipse-fitting algorithm implementation in the impedance measurement system based on DAQ card with FPGA
PublicationThe paper presents an implementation of the ellipse-fitting algorithm in the impedance measurement system based on DAQ card equipped with FPGA chip. The method implementation was tested by simulation means as well as experimentally in the designed and presented measurement system. Finally, the limit values of sampling parameters which assures satisfying accuracy were given.
-
Application of passive sampling technique in monitoring research on quality of atmospheric air in the area of Tczew, Poland.
PublicationThis paper presents the results of atmospheric air quality research in Tczew (adjacent to the Vistula River) on the content of BTEX compounds. Analytical procedure applied during the sampling of the analytes from the air used the passive sampling technique (diffusive passive sampler, Radiello®). For determination of BTEX compounds in atmospheric air, two-stage thermal desorption technique combined with gas chromatography (TD-GC-FID)...
-
Waveform design for fast clutter cancellation in noise radars
PublicationCanceling clutter is an important, but computation-ally intensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. The proposed scheme is potentially capable of canceling clutter in real-time, even for high sampling rates.
-
Analytical Techniques Used in Monitoring of Atmospheric Air Pollutants
PublicationThe air pollution monitoring is one of the most pressing environmental problems today. The paper describes common air pollutants, their interaction and impact on the environment, and classifies the techniques and methods applied in air studies. Furthermore, the review characterizes the selected collection and sampling techniques used for gas sample analysis. Finally, the schematic diagrams of typical designs of systems applied...
-
Simulation of electric hearing - influence of simulation parameters on quality of output signal
PublicationW środowisku programistycznym Matlab stworzono symulację słuchu elektrycznego pacjenta implantowanego. W symulacji zastosowano algorytm przetwarzania wykorzystywany w komercyjnych systemach implantów ślimakowych - CIS (Continuous Interleaved Sampling). W pracy zbadano wpływ ilości kanałów, jak i innych parametrów sygnałów wyjściowych przy zastosowaniu sygału mowy jako sygnału wejściowego symulacji.
-
Polyethylene glycol-coated solid-phase microextraction fibres for the extraction of polar analytes-A review
PublicationThe article discusses the merits and limitations of commercially available solid-phase microextraction (SPME) fibres and compares them with the new type of extraction coatings, in particular those containing polyethylene glycol as sorbent, as well as the methods of the preparation of the latter. It also analyses their possible application for the extraction of a broad spectrum of analytes, with particular emphasis on the sampling...
-
Fast clutter cancellation for noise radars via waveform design
PublicationCanceling clutter is an important, but very expensive part of signal processing in noise radars. It is shown that considerable improvements can be made to a simple least squares canceler if minor constraints are imposed onto noise waveform. Using a combination of FPGA and CPU, the proposed scheme is capable of canceling both stationary clutter and moving targets in real-time, even for high sampling rates.
-
Sea spray as a secondary source of chlorinated persistent organic pollutants? - Conclusions from a comparison of seven fresh snowfall events in 2019 and 2021
PublicationSecondary sources of persistent organic pollutants (POPs) gain in importance worldwide as primary sources decline. In this work, we aim to determine whether sea spray may be a secondary source of chlorinated POPs to the terrestrial Arctic, since a similar mechanism was proposed there only for the more water-soluble POPs. To this end, we have determined polychlorinated biphenyls and organochlorine pesticides concentrations in fresh...
-
Quality of Analytical Results: Classifiying Errors and Estimating Measurement Uncertainty
PublicationThe most important parameter of each analytical result is its reliability. An analytical result is not a constant value; each result has two properties, error and uncertainty. The sources of both these parameters have to be known and their values determined (estimated). All analytical results are obtained by applying an appropriate measuring procedure. The need for reliable results requires application of reliable analytical procedures,...
-
Determination of volatile organic compounds in water samples using membrane-solid phase microextraction (M-SPME) (headspace version)
PublicationThe results of a study on the use of membrane-solid phase microextraction (M-SPME) for sampling volatile organic compounds (VOCs) from the headspace above the liquid medium are presented. The sampled VOCs were subsequently quantified by gas chromatography (GC). Two systems were compared in this study, i.e. a novel two-phase sorption system (M-SPME), and a commercial fibre. Headspace sampling using SPME was optimized with respect...
-
Current trends in solid-phase microextraction (SPME) fibre catings
PublicationThis critical review presents information on known and innovative approaches to the manufacture of fibre coatings used in solid-phase microextraction (SPME). The properties, advantages and drawbacks of the different types of commercially available SPME fibre coatings are discussed in detail, as are those of novel types of coatings and the methodologies of their preparation. The applications of fibre coatings in the solid-phase...