Search
Filters
total: 2119
filtered: 1698
displaying 1000 best results Help
Search results for: incompressible flows
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublicationTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
The influence of sterilization with EnbioJet Microwave Flow Pasteurizer on composition and bioactivity of aronia and blue-berried honeysuckle juices
PublicationIn this study, fruit juices that are rich sources of anthocyanins, obtained from aronia (Am. chokeberry, Aronia melanocarpa) and blueberry honeysuckle (Lonicera caerulea L. var. edulis) were used to examine the preservation of plant phytochemicals and bioactivity upon sterilization -either thermal, or with an EnbioJet microwave flow pasteurizer. The chemical properties verified included determinations of anthocyanins and other...
-
Electrohydrodynamic Secondary Flow and Particle Collection Efficiency in a One-sided Spike-plate Type Electrostatic Precipitator
PublicationIn this work, results of electrohydrodynamic secondary flow and particle collection efficiency measurements in an electrostatic precipitator under positive and negative voltage polarity are presented. The electrostatic precipitator had two plate collecting electrodes and a single spike discharge electrode. The spike tips were only on one side of the discharge electrode, therefore called a one-sided spike electrode. The electrohydrodynamic...
-
FE-investigations of granular flow in silos using an uncoupled ALE-formulation and a non-local hypoplastic model
PublicationArtykuł omawia wyniki naporu materiału sypkiego podczas przepływu w silosach z i bez wkładek. Obliczenia wykonano wykorzystując niepołączone sformułowanie ALE na bazie prawa sprężysto-plastycznego według Druckera-Pragera. Zbadano wpływ kształtu i położenia wkładki na wielkość naporu i rodzaj przepływu.
-
Quantitative estimation of volume changes of granular materials during silo flow using X-ray tomography.
PublicationW artykule przedstawiono wyniki badań doświadczalnych nad zmianami objętościowymi materiału granulowanego podczas przepływu silosowego. Badania wykonano przy zastosowaniu tomografii rentgenowskiej. Wyniki porównano z wynikami doświadczalnymi przy zastosowaniu cyfrowej obróbki zdjęć płynącego materiału.
-
Modelling of Capillary Pressure-driven Water Flow in Unsaturated Concrete Using Coupled DEM/CFD Approach.
PublicationSformułowano nowatorskie, połączone podejście do modelowania dwufazowego przepływu wody napędzanego kapilarami w nienasyconym betonie. Dzięki połączeniu metody elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych proces został zbadany numerycznie w mezoskali w warunkach dwuwymiarowych. Niewielkie próbki betonu o uproszczonej mezostrukturze cząstek poddano w pełni sprzężonym hydromechanicznym...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublicationThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
Evaluating the comfort of use of protective footwear: Validation of a method based on microclimate parameters and peripheral blood flow
Publication -
Impedance plethysmography as a tool for assessing exertion-related blood flow changes in the lower limbs in healthy subjects
Publication -
Fluid structure interaction study of non-Newtonian Casson fluid in a bifurcated channel having stenosis with elastic walls
PublicationFluid–structure interaction (FSI) gained a huge attention of scientists and researchers due to its applications in biomedical and mechanical engineering. One of the most important applications of FSI is to study the elastic wall behavior of stenotic arteries. Blood is the suspension of various cells characterized by shear thinning, yield stress, and viscoelastic qualities that can be assessed by using non-Newtonian models. In this...
-
Modeling of medium flow processes in transportation pipelines - the synthesis of their state-space models and the analysis of the mathematical properties of the models for leak detection purposes
PublicationThe dissertation concerns the issue of modeling the pipeline flow process under incompressible and isothermal conditions, with a target application to the leak detection and isolation systems. First, an introduction to the model-based process diagnostics is provided, where its basic terminology, tools, and methods are described. In the following chapter, a review of the state of the art in the field of leak detection and isolation...
-
Propagation of initially sawtooth periodic and impulsive signals in a quasi-isentropic magnetic gas
PublicationThe characteristics of propagation of sawtooth periodic and impulsive signals at a transducer are analytically studied in this work. A plasma under consideration is motionless and uniform at equilibrium, and its perturbations are described by a system of ideal magnetohydrodynamic equations. Some generic heating/cooling function, which in turn depends on equilibrium thermodynamic parameters, may destroy adiabaticity of a flow and...
-
Modeling and simulation of blood flow under the influence of radioactive materials having slip with MHD and nonlinear mixed convection
PublicationRadioactive materials are widely in industry, nuclear plants and medical treatments. Scientists and workers in these fields are mostly exposed to such materials, and adverse effects on blood and temperature profiles are observed. In this regard, objective of the current study is to model and simulate blood based nanofluid with three very important radioactive materials, named as Uranium dioxide (UO2), Thorium dioxide (ThO2) and...
-
Investigation of the flow, heat and mass transfer and emissions in pulverized fuel fired boiler using physical and numerical modeling.
PublicationPraca przedstawia wykorzystanie techniki modelowania fizycznego trójwymiarowego oraz obliczeń numerycznych umożliwiających symulację rzeczywistych procesów spalania paliw stałych i gazowych w urządzeniach energetycznych. Dodatkowo wyniki obliczeń porównano z wynikami modelowania fizycznego oraz pomiarów na obiekcie rzeczywistym.
-
Does Post-Activation Performance Enhancement Occur during the Bench Press Exercise under Blood Flow Restriction?
Publication -
Modeling of heat and fluid flow in granular layers using high-order compact schemes and volume penalization method
Publication -
Does blood flow restriction influence the maximal number of repetitions performed during the bench press? A pilot study
Publication -
Hydrogel Delivery System Containing Calendulae flos Lyophilized Extract with Chitosan as a Supporting Strategy for Wound Healing Applications
Publication -
A robust optimization model for affine/quadratic flow thinning: A traffic protection mechanism for networks with variable link capacity
Publication -
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublicationW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
Direct Current Atmospheric Pressure Microdischarge Generated between a Miniature Flow Helium Microjet and a Flowing Liquid Cathode
Publication -
Decolorization of organic dyes solution by atmospheric pressure glow discharge system working in a liquid flow-through mode
Publication -
The Acute Effects of External Compression With Blood Flow Restriction on Maximal Strength and Strength-Endurance Performance of the Upper Limbs
Publication -
Flow structure, heat transfer and scaling analysis in the case of thermo-magnetic convection in a differentially heated cylindrical enclosure
PublicationThe experimental, numerical and scaling analysis in the case of thermo-magnetic convection in a thermosyphon-like enclosure filled with a paramagnetic fluid is presented. Visualization of temperature field together with the numerical simulation gave an information about the flow structure, which indicated “finger-like” structures of hot and cold streams advecting each other. Their number depended on the Rayleigh number and also...
-
Inverse method for axisymmetric and blade-to-blade viscous flow models in cylindrical coordinates using stream-function transformation
PublicationZaproponowano nową metodę odwrotną rozwiązywania dwuwymiarowych zagadnień projektowych we współrzędnych cylindrycznych. Użyto współrzędnych funkcji prądu uzależniając kształt opływanej geometrii od kształtu linii prądu. Metodę zwalidowano. Pokazano zastosowanie do przepływów osiowosymetrycznych jak i na powierzchniach cylindrycnych.
-
Multi-DBD plasma actuator for flow separation control around NACA 0012 and NACA 0015 airfoil models
PublicationIn this paper application of innovative multi-DBD plasma actuator for flow separation control is presented. The influence of the airflowgenerated by this actuator on the flow around NACA 0012 and NACA 0015 airfoil models was investigated. The results obtained from 2D PIVmeasurements showed that the multi-DBD actuator with floating interelectrode can be attractive for leading and trailing edge separation control.
-
Modeling two phase flow in large scale fractured porous media with an extended multiple interacting continua method
PublicationWe present a two phase flow conceptual model, the corresponding simulator (2pMINC) and a workflow for large-scale fractured reservoirs, based on a continuum fracture approach which uses the multiple interacting continua (MINC) method complemented with an improved upscaling technique. The complex transient behavior of the flow processes in fractured porous media is captured by subgridding the coarse blocks in nested volume elements...
-
Nowy system diagnostyki cieplno-przepływowej obiektów energetycznych.The new system of power units thermal and flow diagnostics.
PublicationPrzedstawiono zmodernizowany system diagnostyki urządzeń składowych obiegów cieplnych bloków energetycznych. Wskazano na zalety zastosowania do tego sztucznych sieci neuronowych (SSN). Opisano dokładność SSN zastosowanych do poszukiwania typów degradacji geometrycznych i do rozpoznawania rozmiarów degradacji geometrycznych.
-
Badania wrzenia R22 w rurkach z powłoką porowatą. Investigation of R22 flow boiling in porous tubes.
PublicationW pracy przedstawiono wyniki pomiarów współczynnika przejmowania ciepła przy wrzeniu w przepływie R22 w poziomej rurce z aluminiową powłoką porowatą. Otrzymane dane odniesiono do wyników uzyskanych dla gładkiej stalowej rurki oraz rurki typu microfin. Rurka gładka i z powłoką porowatą była wykonana ze stali nierdzewnej o grubości ścianki 0.6 mm. Grubość powłoki porowatej wynosiła 0,2 mm. Eksperymenty prowadzono przy stopniu suchości...
-
Pressure-induced flow processing behind the superior mechanical properties and heat-resistance performance of poly(butylene succinate)
PublicationWe propose a pressure-induced flow (PIF) processing method for the simultaneous enhancement of strength, toughness, and heat resistance of biodegradable poly(butylene succinate) (PBS). The pressure and temperature were systematically adjusted to optimize the tensile strength of PBS. Under the optimized processing conditions, the structured PBS was characterized by relatively high strength of 89.5 MPa, toughness of 21.4 kJ·m−2 ,...
-
Uncertainty of mass flow measurement using centric and eccentric orifice for Reynolds number in the range 10,000 ≤ Re ≤ 20,000
PublicationThe article analyses the impact of the Reynolds number on the estimated uncertainty of the mass flow rate measurement using an orifice plate. The objects of the research were two types of orifices: centric (ISA) and eccentric, with the diameter ratio β = 0.5. Studies were performed by Monte Carlo simulation and experiments for Reynolds numbers in the range 10,000 ≤ Re ≤ 20,000. The obtained results have shown that for both orifice...
-
Improved semi-empirical method for determination of heat transfer coefficient in flow boiling in conventional and small diameter tubes
PublicationPraca dotyczy przedstawienia poprawionego modelu umożliwiającego wyznaczanie współczynnika przejmowania ciepła w kanałach o małych średnicach jaj i tych tradycyjnych. Model zweryfikowano na 6 czynnikach chłodnuiczych uzyskując bardzo zadowalającą zgodność.
-
A High-Arctic flow-through lake system hydrochemical changes: Revvatnet, southwestern Svalbard (years 2010–2018)
PublicationLake ecosystems are strongly coupled to features of their surrounding landscapes such as geomorphology, lithology, vegetation and hydrological characteristics. In the 2010–2018 summer seasons, we investigated an Arctic flow-through lake system Revvatnet, located in the vicinity of the coastal zone of Hornsund fjord in Svalbard, characterising its hydrological properties and the chemical composition of its waters. The lake system...
-
Double-diffusive natural convection energy transfer in magnetically influenced Casson fluid flow in trapezoidal enclosure with fillets
PublicationThe prime motive of this disquisition is to deal with mathematical analysis of natural convection energy transport driven by combined buoyancy effects of thermal and solutal diffusion in a trapezoidal enclosure. Casson fluid rheological constitutive model depicting attributes of viscoelastic liquids is envisioned. The influence of the inclined magnetic field governed by Lorentz field law is also considered. To raise the essence...
-
Energy losses in hydrostatic drive:Drive investigation method compatible with diagram of power increase opposite to the direction of power flow
PublicationEnergy losses and efficiency of drive motor must be presented as functions of physical quantities independent of losses in the motor. Such quantities are speed and load required by the driven device, changing in the drive operating field. Speed and load decide of the useful power and, in differentiated way, of kinds and values of losses in the motor. But energy losses and efficiency of drive motors are evaluated as functions of...
-
Combining X-ray tomogrpahy imaging and DEM simulations to investigate granular material flow during silo discharging
PublicationEven after few decades of research, the study of particle motion taking place during silo discharging hasn’t been fully addressed, both experimentally and numerically, because of nontrivial behaviors that occur during associated flow patterns. For instance, discrete element method (DEM) has shown good qualitative prediction potential of velocity profile, but, on the other hand, frequently failed to match quantitatively experimental...
-
Modelling of Objects Behaviour for Their Re-identification in Multi-camera Surveillance System Employing Particle Filters and Flow Graphs
PublicationAn extension of the re-identification method of modeling objects behavior in muti-camera surveillance systems, related to adding a particle filter to the decision-making algorithm is covered by the paper. A variety of tracking methods related to a single FOV (Field of Vision) are known, proven to be quite different for inter-camera tracking, especially in case of non-overlapping FOVs. The re-identification methods refer to the...
-
Decahedral-shaped anatase titania photocatalyst particles: Synthesis in a newly developed coaxial-flow gas-phase reactor
PublicationDecahedral-shaped anatase particles (DAPs) were prepared by a gas-phase process consisting of titanium(IV) chloride oxidation. The use of a coaxial-flow gas-phase reactor resulted in high reaction yield (ca. 70%) and good reproducibility of DAPs production. The influence of controlled and resultant preparation parameters on the process course and on DAPs properties (such as specific surface area, particle size and particle morphology)...
-
Application of Particle Image Velocimetry method for monitoring the volume changes during silo flow on the basis of X-radiographs
PublicationW artykule przedstawiono wyniki badań nad zastosowaniem techniki pomiarowej PIV (Particle Image Velocimetry) do analizy zmian objętościowych zachodzących w materiale sypkim w czasie opróżniania silosu prostokątnego. Jako mateirły do analizy wykorzystano cyfrowe radiografy uzyskane z kontynualnej rejestracji z użyciem systemu tomografii promieni X. Szcególny nacisk położono na analizę zmian objętościowych zachodzącyh w kanale przepływu.
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublicationW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublicationThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Deterministic versus stochastic modelling of unsaturated flow in a sandy field soil based on dual tracer breakthrough data
PublicationThe 216 km2 Neuenhagen Millcreeck catchment can be characterized as a drought sensitive landscape in NE Germany. It is therefore a fundamental human interest to understand how water that fell as precipitation moves through the unsaturated soils and recharges groundwater. Additionally, a better knowledge of nutrient transport from soil to groundwater is important also, especially in landscapes with light sandy soils. For a better...
-
Initial Report on Numerical Modeling of Blood Flow in Myocardial Bridge Region of Coronary Artery: Concept of Model Validation
PublicationThe paper presents a numerical method of blood flow simulation within the coronary artery covered by the myocardial bridge. The myocardial bridge is a congenital coronary abnormality caused by the blood vessel location under one of the heart muscles. In this case, the blood flow within the vessel is partially disturbed which can cause several consequences. The presented numerical simulation allowed us to estimate the blood flow...
-
New hybrid quadrature schemes for weakly singular kernels applied to isogeometric boundary elements for 3D Stokes flow
PublicationThis work proposes four novel hybrid quadrature schemes for the efficient and accurate evaluation of weakly singular boundary integrals (1/r kernel) on arbitrary smooth surfaces. Such integrals appear in boundary element analysis for several partial differential equations including the Stokes equation for viscous flow and the Helmholtz equation for acoustics. The proposed quadrature schemes apply a Duffy transform-based quadrature...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublicationThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Modelling of shear localization during granular flow within non-local hypoplasticity using material point method
PublicationArtykuł omawia wyniki numeryczne dotyczące powstawania lokalizacji odkształceń stycznych w materiałach granulowanych Obliczenia wykonano dla ściskania dwuosiowego i przypływu silosowego stosując hipoplastyczny model konstytutywny rozszerzony o długość charakterystyczną w ramach nielokalnej teorii. Zastosowano podejście punktów materialnych w celu uniknięcia nadmiernej deformacji elementów skończonych.
-
Wave energy attenuation in fields of colliding ice floes – Part 2: A laboratory case study
Publication -
Equivariant Morse equation
PublicationThe paper is concerned with the Morse equation for flows in a representation of a compact Lie group. As a consequence of this equation we give a relationship between the equivariant Conley index of an isolated invariant set of the flow given by x˙ = − ∇f(x) and the gradient equivariant degree of ∇f. Some multiplicity results are also presented.
-
ANALYSIS OF THE IMPACT OF THE PLANNED SEWAGE DISCHARGE FROM THE ‘NORTH’ POWER PLANT ON THE VISTULA WATER QUALITY
PublicationThe paper presents results of analysis of the industrial sewage discharge impact from the ‘North’ Power Plant on the Vistula water quality around 45+330 of the river kilometer. For the analysis, the two-dimensional models of flow, impurities and temperature transport were used. Hydrological conditions of the analyzed section of the river, characteristic flows and bathymetry of the riverbed in the first instance were defined....
-
The assessment of metrological properties of segmental orifice based on simulations and experiments
PublicationSegmental orifices are often used to measure flows of heterogeneous mixtures, especially in flow meters in the power industry, for example. The orifice (with module m= 0.25) was installed in a stainless-steel pipe with internal diameter of 50 mm, placed in a hydraulic water system. The research was performed for Reynolds numbers ranging from 9,000 to 17,000. The flow characteristics of this orifice obtained based on simulation...