Filters
total: 1268
filtered: 1072
displaying 1000 best results Help
Search results for: VEHICULAR ROADS
-
Analysis od dynamic loads on lightweight footbridge caused by lorry passing underneath
PublicationW artykule przedstawiono analizę drgań lekkiej kładki dla pieszych wywołanych przejazdem ciężarówki z dużą prędkością pod spodem konstrukcji.
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublicationThis paper presents a description of an effective method for determining loads due to waves, current and wind acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was...
-
Mechanical behaviour of the implant used in human hernia repair under physiological loads
PublicationIn laparoscopic operations of abdominal hernias some recurrences still take place, even when applying a surgical mesh. This is usually caused by a failure of the connection between the tissue and the implant. The study deals with the influence of an implant’s orientation on forces in joints, which connect the mesh to human tissues. In the paper, the implant is modelled as a membrane structure within framework of the Finite Element...
-
Sensitivity analysis of buckling loads of bisymmetric I-section columns with bracing elements
PublicationWyznaczono pierwsza wariacje siły krytycznej wyboczenia słupa o przekroju bisymetrycznym otwartym przy wariacji sztywnosci i połozenia stezen. Przyjeto załozenia klasycznej teorii pretów cienkosciennych o nieodkształcalnym przekroju poprzecznym. Analizowano zarówno stezenia boczne jak i stezenia ograniczajacespaczenie oraz skrecenie przekroju poprzecznego. Stezenia modelowano jako podpory sprezyste. W przykładzie numerycznym zbadano...
-
On delamination threshold loads in low velocity impact on glass-carbon/epoxy composites.
PublicationZbadano możliwości zastąpienia badań udarowych o niskiej energii ze spadającą masą badaniami quasi-statycznymi przy analogicznym obciążeniu próbki dla laminatów epoksydowych wzmocnionych włóknami węglowymi i szklanymi oraz węglowymi. Uzyskano dobrą zgodność wyników obu typów badań , co znajduje potwierdzenie w wynikach innych badaczy.
-
On numerical analysis of a thin-walled I-beam with warping stiffenes undertorsional loads
PublicationPraca jest streszczeniem referatu wygłoszonego na międzynarodowej konferencji Metody Komputerowe w Mechanice, Wisła, 3-6 czerwca 2003. Przedstawiono problem numerycznej analizy belek cienkościennych ze stężeniami. Omówiono dwa modele jednowymiarowe: jeden bazujący na koncepcji skupionej sztywności bimomentowej, a drugi na zastosowaniu superelementu MES. Otrzymane wyniki porównano z rezultatami analizy MES przy zastosowaniu dyskretyzacji...
-
The large rotations theory of elasto-viscoplastic shells subjected to thedynamic and thermal loads.
PublicationPrzedstawiono problemy sprężysto- lepkoplastycznej analizy geometrycznie nieliniowych płyt i powłok poddanych obciążeniom dynamicznym w różnych temperaturach. W obliczeniach zastosowano teorię ścinania pierwszego rzędu i konstytutywne prawo Chaboche´a w wariantach z uwzględnieniem wpływu temperatury na stałe materiałowe. Do całkowania równań ruchu użyto metody różnic centralnych, a do całkowania równań konstytutywnych regułę...
-
Spectral criterion of infinite fatigue life of beams under asymmetric random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych stałym i zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium nieograniczonej trwałości...
-
Spectral criterion of infinite fatigue life of beams under combined random loads
PublicationRozpatrywana jest trwałość zmęczeniowa belek poddanych zmiennym obciążeniom osiowym, giętnym i skrętnym o znanych gęstościach widmowych mocy i zerowych wartościach średnich. Założono, że materiał posiada granicę zmęczenia i jest zgodny z modelem Kelvina-Voigta, oraz że składowe naprężenia są stacjonarne, stacjonarnie skorelowane i różniczkowalne w sensie średniokwadratowym. Zdefiniowano naprężenie równoważne i sformułowano kryterium...
-
Possibility of defining of the average loads of main propulsion on the basis of ship design parameters.
PublicationZaprezentowano możliwość określania zależności między mocą holowania wybranych typów statków a średnim obciążeniem napędu głównego podczas pływania swobodnego. Przedstawione badania umożliwiają wyznaczenie średnich obciążeń napędu głównego podczas pływania swobodnego przy wykorzystaniu parametrów projektowych statku zawartych w założeniach armatorskich.
-
Nonlocalized thermal behavior of rotating micromachined beams under dynamic and thermodynamic loads
PublicationRotating micromachined beams are one of the most practical devices with several applications from power generation to aerospace industries. Moreover, recent advances in micromachining technology have led to huge interests in fabricating miniature turbines, gyroscopes and microsensors thanks to their high quality/reliability performances. To this end, this article is organized to examine the axial dynamic reaction of a rotating...
-
Operational loads of dredge pumps in their basic service states on selected types of dredgers
PublicationArtykuł przedstawia wyniki badań eksploatacyjnych dotyczący jednego z najważniejszych odbiorników energii mechanicznej na pogłębiarkach - pomp gruntowych. Badania eksploatacyjne obejmowały pomiary parametrów charakteryzujących obciążenia pomp gruntowych w dwóch podstawowych stanach ich eksploatacji, a mianowicie podczas załadunku ładowni gruntowej (pogłębiarki lub szalandy) oraz podczas refulowania gruntu na ląd.
-
HIERARCHICAL CYCLES IN MODERN POWER SYSTEMS – EXERGY ANALYSIS UNDER PART LOADS
PublicationThe aim of the paper is to investigate thermodynamic efficiency of advanced hierarchic power cyclesunder partial loads by using of exergy analyze. Advanced hierarchical power systems arecomposed of few energy conversion cycles, most common are steam and gas cycles in various configurations, but they may contain fuel cells, ORC, lithium bromide absorption chillers and others. Moreover hierarchical cycles can be powered by several...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Effective method for determining environmental loads on supporting structures for offshore wind turbines
PublicationThis paper presents a description of an effective method for determining loads due to waves and current acting on the supporting structures of the offshore wind turbines. This method is dedicated to the structures consisting of the cylindrical or conical elements as well as (truncates) pyramids of polygon with a large number of sides (8 or more). The presented computational method is based on the Morison equation, which was originally...
-
LLA : A New Anypath Routing Scheme Providing Long Path Lifetime in VANETs
PublicationVehicular ad-hoc networks (VANETs) are a promising solution to improve the road traffic safety, reduce the environmental pollution, or simply provide the on-board infotainment services. However, these actions are often not possible due to high mobility of vehicles causing frequent failures of VANET links. In this paper, we focus on anypath routing to improve the reliability of multihop VANET communications. In particular, the paper...
-
The Impact of Road Network Structure and Mobility on the National Traffic Fatality Rate
Publication -
Certification of vehicles used for tire/road noise evaluation by CPX method
PublicationJednym ze sposobów oceny hałasu opon i nawierzchni drogowych jest metda CPX polegająca na pomiarze hałasu w polu bliskim miejsca współpracy opony z nawierzchnią. Aby uzyskać wysoką dokładność pomiarów niezbędne jest ustanowienie procedur ustanowienie procedur certyfikacyjnych sprzętu pomiarowego a więc głównie pojazdu badawczego. Praca dotyczy procedur certyfikacyjnych wypracowanych przez Grupę Roboczą WG33 ISO/TC43/SC1 oraz w...
-
GAMBIT's position within the European Union's III Road Safety Plan
PublicationOtwarcie Seminarium GAMBIT 2006, poświęcone wnioskom z dotychczasowych działań oraz planom na przyszłość, zawartym w najnowszym Krajowym Programie GAMBIT 2005. Prace nad nim rozpoczęto w sierpniu 2004, czyli tuż po wejściu Polski do Unii Europejskiej. W kwietniu 2005 Rada Ministrów przyjęła GAMBIT 2005 jako program dla Polski na lata 2005-2013, skonstruowany zgodnie z metodyką opracowaną dla tych krajów UE-25, których poziom zagrożenia...
-
The Comparison of the Emissions from Light Duty Vehicle in On-road and NEDC Tests
Publication -
The New Silk Road: Seeking Opportunities for Polish Exports in the Chinese Market
Publication -
Laboratory Investigations of Frost Susceptibility of Aggregates Applied to Road Base Courses
Publication -
The Sustainable Development and Economic Impact of China’s Belt and Road Initiative in Ethiopia
Publication -
Influence of 8-Hour Road Transportation on Selected Physiological Parameters in Horses
Publication -
Influence of the mobility package on the functioning of the Polish road transport of goods sector
Publication -
Site environment type – The main factor of urban road dust toxicity?
Publication -
The Impact of COVID-19 on Road Freight Transport Evidence from Poland
Publication -
Foreign visitors from Visegrad countries with regard to road safety in Poland
PublicationIn the paper the authors present road safety situation in the Polish regions mostly visited by Czech, Slovakian and Hungarian tourists. These regions include Mazowieckie, Dolnoslaskie, Slaskie and Malopolskie voivodeships. After description of the regions and main touristic destinations for foreigners from Visegrad countries, a detailed road safety analysis performed for the period 2007-2012 is given. The paper ends with conclusions in...
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublicationTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Mn Road Facility Badania nawierzchni drogowych w amerykańskim stylu
PublicationPomimo znacznego rozwoju technik modelowania matematycznego oraz badań laboratoryjnych nie jest obecnie możliwe wyeliminowanie badań nawierzchni drogowych i ich monitorowania w warunkach drogowych. W pracy przedstawiono drogowe badania oporu toczenia opon samochodowych na torach doświadczalnych Francji i Stanów Zjednoczonych wykonane za pomocą przryczepy dynamometrycznej zbudowanej w Politechnice Gdańskiej. Podano przykładowe wyniki...
-
Identification of discontinuites in composite rods and beams based on Lamb wave propagation
PublicationW pracy omówiono metodę identyfikacji typu nieciągłości w belkach i prętach kompozytowych, oparta o analizę zmain w propagacji fali Lamba.
-
Comparative analysis of process alternatives for manufacturing piston rods of hydraulic cylinders.
PublicationZawarto wyniki analiz porównawczych alternatywnych technologii tłoczysk siłowników hydraulicznych w warunkach elastycznej automatyzacji wytwarzania. Uwzględniając zarówno tradycyjne struktury tych procesów z operacjami szlifowania i polerowania, jak i nowoczesne technologie z operacjami nagniatania, przedstawiono zintegrowane podejście do planowania sekwencji operacji procesu i harmonogramowania zadań produkcyjnych wraz z algorytmem...
-
Development of Intelligent Road Signs with V2X Interface for Adaptive Traffic Controlling
PublicationThe objective of this paper is to present a practical project of intelligent road signs, under which a series of new products for the regulation of traffic is being created. The engineering part of the project, described in this paper, was preceded by a series of experimental studies, the results of which were described in another paper accepted for publication at the MTS-ITS conference 2019, entitled "Comparative study on the effectiveness...
-
Tire/road noise measuring principles according to the Close Proximity Method
PublicationW pracy podano metody badania hałasu opon samochodowych. Omówiono przyczepy pomiarowe zbudowane w Politechnice Gdańskiej oraz systemy pomiarowe stosowane do pomiaru hałasu opon zgodnie z metodą CPX.
-
Investigation of the road noise source employing an automatic noise monitoring station
PublicationThe paper presents a pilot investigation of noise source models in two selected localizations in the context of future dynamic noise map creation. The experiments were carried out using the automatic noise monitoring station engineered at the Multimedia Systems Departmentof the Gda´nsk University of Technology. The results of the noise measurements employing monitoring stations and its comparison to the reference values are depicted....
-
Introduction to smart solutions for wastewater: Road-mapping the transition to circular economy
PublicationToday there is an urgent need to move from a linear to a circular economy approach with special focus to water and environment. Despite the paramount importance, this transition is hampered by barriers which concern not only technological but embrace also organizational, regulatory, social, and economic aspects. In order to overcome such barriers, innovative water-smart solutions are needed and a robust roadmap for the transition...
-
Road safety analysis in Poland using time-series modelling techniques
PublicationA number of international studies argue that there is a correlation between the number of traffic fatalities and the degree of public activity. The studies use the unemployment rate to support that argument. As unemployment grows miles travelled fall, a factor known to affect road safety. This relationship seems to be true for Poland, as well. The model presented in the paper is intended to prove it. It is a structural time-series local...
-
Probabilistic analysis of settlements under a pile foundation of a road bridge pylon
PublicationThe paper addresses the reliability change of a road bridge pile foundation due to the unpredictable increase of settlements in time. The analysis is based on the Rędziński Bridge in Wrocław, Poland, its design assumptions, and monitoring results. The bridge foundation rests on a multi-layered subsoil assumed random. The Finite Element model of the subgrade is generated in ZSoil® software. To simplify the probabilistic approach,...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Spatial differentiation of road safety in Europe based on NUTS-2 regions
PublicationRoad safety varies significantly across the regions in Europe. To understand the factors behind this differentiation and the effects they have, data covering 263 NUTS-2 (Nomenclature of Territorial Units for Statistics) regions across Europe (European Union and Norway) have been analysed. The assessment was made using Geographically Weighted Regression (GWR). As a dependent variable the Road Fatality Rate (RFR – number of fatalities...
-
Times Series Analysis Of Road Safety Trends At The Regional Level In Poland
PublicationThe paper presents possibility of applying a structural times series modeling with explanatory and intervention variables as a tool capable for explaining the changes in the monthly number of fatalities and seriously injured in traffic accidents. The analysis covers regional level and takes into consideration traffic accidents data of two regions: Pomorskie and Warmia-Mazury. In addition short-term forecasts for the two regions...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublicationThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Comparative study on the effectiveness of various types of road traffic intensity detectors
PublicationVehicle detection and speed measurements are crucial tasks in traffic monitoring systems. In this work, we focus on several types of electronic sensors, operating on different physical principles in order to compare their effectiveness in real traffic conditions. Commercial solutions are based on road tubes, microwave sensors, LiDARs, and video cameras. Distributed traffic monitoring systems require a high number of monitoring...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublicationThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
The effects of selected factors on regional road fatalities – analysis of the Łódź region
PublicationAnalysis of regional accident records shows that a country’s national road safety programme does not have the same effect in each of its regions. What may be a serious problem in one region may be of marginal significance in another. Polish and international experience shows that main risk groups and types of accidents related to the level of development and quality of the road network differ from region to region. The conclusion...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublicationThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Development of tools for road infrastructure safety management for the provinces (voivodeships) in Poland
PublicationThe development of modern tools for road infrastructure safety management will help to reduce the number of fatalities and serious injuries as one of the main objectives adopted in 2013 in the National Road Safety Programme 2014-2020 and the new Road Safety Programme 2011-2020 in the EU. Risk Management in Highway Engineering can be applied in developing tools essential in the process of safety management. Risk Management in Highway...
-
Stability analysis of a road scarp in the Carpathian Mountains and methods of its protection
PublicationThe purpose of the study was to analyse the stability of a road scarp endangered by a landslide and to consider some measures for its stabilization. The potential landslide could unfavourably alter the shape of the slope, thus a religious sanctuary situated above the slope. The present research has resulted in suggestions of possible protection methods, namely, drainage, soil nailing, installation of piles, supporting the scarp...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublicationPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...