Filters
total: 1222
filtered: 894
Search results for: audible noise
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublicationDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Investigation of noise threats and their impact on hearing in selected schools - a pilot study.
PublicationNoise measurements conducted in selected schools in Gdansk area are presented in this paper. The main aim of this research was to determine noise threats at schools. Some objective measurements of the acoustic climate were performed employing a noise monitoring station engineered at the Multimedia System Department, Gdansk University of Technology. Simultaneously, subjective noise annoyance examinations were carried out among pupils...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublicationThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Three solvers for MIMO noise radar clutter cancellation - a performance comparison
PublicationThe problem of canceling strong clutter echos in a MIMO noise radar is considered. Execution times of three algorithms is compared. The first solution is a standard Least Squares approach employing Cholesky decomposition of the transmitted signal sample autocorrelation matrix. The second approach is based on careful waveform design which guarantees that the signal sample autocorrelation matrix has Toeplitz structure. This enables...
-
Tracking of the broadband source of the underwater noise in the very shallow water conditions
PublicationThe paper contains the result s, both theoretical and experimental , connected with the tracking of the underwater noise source as small ships, pontoon , diver and so on. The pro blem of security in the shallow water area is the challenge for underwater acousticians. In this paper there is take n into account the detection of the sources that move on the surface of the sea or underwater in shallow...
-
Barkhausen noise properties measured by different methods for deformed Armco samples
PublicationPorównano właściwości sygnału napięciowego efektu Barkhausena (BN) uzyskanego za pomocą 'sondy punktowej' (użytecznej dla badań przemysłowych) oraz cewki otaczającej badany materiał. W pierwszej metodzie mierzono trzy wielkości: V1 - napięcie skuteczne, Nc - liczba impulsów, V2 - napięcie kontrolne z cewki. W drugiej metodzie z napięcia indukowanego w cewce wyznaczano pętlę histerezy B(H), obwiednie z napięcia skutecznego a także...
-
Frequently updated noise threat maps created with use of supercomputing grid
PublicationAn innovative supercomputing grid services devoted to noise threat evaluation were presented. The services described in this paper concern two issues, first is related to the noise mapping, while the second one focuses on assessment of the noise dose and its influence on the human hearing system. The discussed services were developed within the PL-Grid Plus Infrastructure which accumulates Polish academic supercomputer centers....
-
Investigation of RTS Noise in Reverse Polarized Silicon Carbide Schottky Diodes
PublicationOne of the method of electronic device quality and reliability evaluation is observation of its inherent noise. The RTS phenomena usually indicates the presence of large defects in the structure of the material of the device, therefore it can be treated as an indicator of technology quality. In the paper authors present results of RTS investigations in reverse polarized Silicon Carbide Schottky diodes. Devices being studied are...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublicationTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Review and comparison of smoothing algorithms for one-dimensional data noise reduction
PublicationThe paper considers the choice of parameters of smoothing algorithms for data denoising. The impact of the window size on smoothing accuracy was analyzed. The parameters of denoising filters were selected with respect to the meansquare error between the computed linear regression and the noisy signal. Finally, we have compared mean, median, SavitzkyGolay, Kalman and Gaussian filter algorithms for the data from the digital sensor....
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublicationThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublicationPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
On the Handling of Outliers in the GNSS Time Series by Means of the Noise and Probability Analysis
PublicationThe data pre-analysis plays a significant role in the noise determination. The most important issue is to find an optimum criterion for outliers removal, since their existence can affect any further analysis. The noises in the GNSS time series are characterized by spectral index and amplitudes that can be determined with a few different methods. In this research, the Maximum Likelihood Estimation (MLE) was used. The noise amplitudes...
-
Implementation of constant component filter in measurements of random telegraph signal noise
PublicationNoise is generated in all semiconductor devices. The intensity of these fluctuations depends on used elements, manufacturing process, operating conditions and device type. The result noise is a superposition of different kinds of fluctuations like thermal noise, generation-recombination noise, 1/f noise, shot noise and Random Telegraph Signal (RTS) noise. The last one, RTS noise is observed as nonstationary impulse fluctuations....
-
Global Optimization for Recovery of Clipped Signals Corrupted With Poisson-Gaussian Noise
PublicationWe study a variational formulation for reconstructing nonlinearly distorted signals corrupted with a Poisson-Gaussian noise. In this situation, the data fidelity term consists of a sum of a weighted least squares term and a logarithmic one. Both of them are precomposed by a nonlinearity, modelling a clipping effect, which is assumed to be rational. A regularization term, being a piecewise rational approximation of the ℓ0 function...
-
Creating Dynamic Maps of Noise Threat Using PL-Grid Infrastructure
PublicationThe paper presents functionality and operation results of a system for creating dynamic maps of acoustic noise employing the PL-Grid infrastructure extended with a distributed sensor network. The work presented provides a demonstration of the services being prepared within the PLGrid Plus project for measuring, modeling and rendering data related to noise level distribution in city agglomerations. Specific computational environments,...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublicationTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Investigating Noise Interference on Speech Towards Applying the Lombard Effect Automatically
PublicationThe aim of this study is two-fold. First, we perform a series of experiments to examine the interference of different noises on speech processing. For that purpose, we concentrate on the Lombard effect, an involuntary tendency to raise speech level in the presence of background noise. Then, we apply this knowledge to detecting speech with the Lombard effect. This is for preparing a dataset for training a machine learning-based...
-
A review of design approaches for the implementation of low-frequency noise measurement systems
PublicationElectronic noise has its roots in the fundamental physical interactions between matter and charged particles, carrying information about the phenomena that occur at the microscopic level. Therefore, Low-Frequency Noise Measurements (LFNM) are a well-established technique for the characterization of electron devices and materials and, compared to other techniques, they offer the advantage of being non-destructive and of providing...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublicationWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Analysis of the Usefulness of Cheap Audio Recorders for Spectral Measurement of Environmental Noise
PublicationEnvironmental noise pollution is nowadays one of the most serious health threats. The impact of noise on the human body depends not only on the sound level but also on its spectral distribution. Reliable measurements of the environmental noise spectrum are often hampered by the very high price of top quality measuring devices. This paper explores the possibility of using much cheaper audio recorders for the frequency analysis....
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Medication-Related Osteonecrosis of the Mandible Treated with Marginal Resection: A Case Report
Publication -
Nutritional value, protein and peptide composition of edible cricket powders
Publication -
Electronic noses in classification and quality control of edible oils: A review
PublicationThe growing demand for wholesome and nutritious food leads to intensification of production, which in turn can have a detrimental effect on quality and well-being of consumers. For that reason, it is important to develop novel methods of food control which would be characterized by a short time of analysis, adequate sensitivity and relatively low cost. One such technique involves the use of multi-sensory devices called electronic...
-
A system for multitask noisy speech enhancement.
PublicationW artykule przedstawiono ogolną charakterystyke opracowanego systemu rejestracji i rekonstrukcji mowy. Artykuł zawiera opis składników systemu, ktory jest oprogramowaniem zawierającym zaawansowane narzędzia służące poprawie zrozumiałości mowy. Zaimplementowane narzędzia systemu umożliwiają wyszukiwanie nagrań dźwiękowych i ich obróbkę przy pomocy zaimplementowanych pluginów. W artykule przedstawione wykorzystane w systemie algorytmy...
-
Multitask Noisy Speech Enhancement System
PublicationW referacie opisano Wielozadaniowy System Poprawy Jakości Sygnału Mowy. Jest to wyspecjalizowany pakiet oprogramowania przeznaczony do rejestrowania sygnału mowy i do poprawy jego jakości oraz zrozumiałości mowy, przy użyciu zaawansowanych procedur cyfrowego przetwarzania sygnału. Pakiet oprogramowania składa się z programów: Rejestrator, Przeglądarka oraz Rekonstruktor. Oprogramowanie to może być użyte w przypadkach, gdy zrozumiałość...
-
Monitoring of single-side lap grinding with electroplated tools
PublicationThe results presented in the paper show that utilising microphones as audible sound sensors is a suitable approach for monitoring a single-side lap grinding process due to the low levels of noise generated by the drives of a machine tool. The results confirm that sound signal analysis is a feasible and relatively simple method to monitor a lap grinding process with the use of an audible sound sensor. Proposed method can be used...
-
the assessment of the noise-induced harmful effects based on the properties of human hearing system
PublicationA new way of assessment of noise-induced harmful effects on human hearing system is presented in the paper. The method takes into consideration properties of the human hearing system. The pro-posed method determines the cumulative impact on hearing system produced by the excessive noise. Based on the predicted effects of the noise exposure, the new types of noise indicators were developed. The evaluation of these indicators was...
-
Road noise mapping in the city area: measurements compared to model-based estimations
PublicationThe paper presents an approach to the verification of noise prediction models in selected localization in the city of Gdansk. The experiments described include a comparison between environmentalmeasurement results performed in the terrain and the noise level prediction results. The NMPB-96 (Nouvelle Méthode de Prévision du Bruit) and Harmonoise models outcomes provide the subject ofthe analysis. The proposed solution of continuous...
-
<title>New low noise CCD cameras for Pi-of-the-Sky project</title>
Publication -
Resistance noise in tio2-based thin film gas sensors underultraviolet irradiation
PublicationBadano możliwości wykorzystania fluktuacji rezystancji w cienkich warstwach TiO2 do wykrywania gazów. Pomiary przeprowadzono, gdy próbka była oświetlona promieniowaniem ultrafioletowym o długości 370nm, w obecności gazu H2S. Stwierdzono, że fluktuacje rezystancji są indukowane promieniowaniem ultrafioletowym i pozwalają na wykrycie obecności H2S w stężeniu do 1.5 ppm.
-
Comparing noise levels and audiometric testing results employing it based diagnostic systems.
PublicationW referacie przedstawiono Internetowy system przeznaczony do przeprowadzania przesiewowych testów słuchu. Zaprezentowano również system informacyjny przeznaczony do monitorowania hałasu środowiskowego. Obie Internetowe aplikacje mogą być pomocne w zmniejszaniu częstości występowania chorób słuchu powodowanych przez hałas środowiskowy i przemysłowy. Porównano wyniki testów audiometrycznych z pomiarami hałasu na podstawie zawartości...
-
Higher-order spectra for harmonics detection in nonlinear systems at presence of Gaussian noise.
PublicationPrzedstawiono metodę wykrywania harmonicznych w ukladach nieliniowych za pomocą funkcji bispektrum. Przebadano skuteczność proponowanej metody w porównaniu z metodą wykorzystującą gęstość widmową mocy. Badania przeprowadzono dla sygnałów będących sumą sygnału harmonicznego i realizacji szumu białego.
-
Experimental study of corrosion in reinforced concrete by acoustic emission and electrochemical noise techniques
PublicationTechnika emisji akustycznej jest znaną metodą badań korozji zbrojenia żelbetu. Źródłem aktywności akustycznej są zawsze zjawiska o naturze mechanicznej. Przedstawiono wynik badań akustycznych zbrojonego betonu w warunkach polaryzacji anodowej, przyspieszającej procesy korozyjne. Symultanicznie prowadzona była rejestracja szumu elektrochemicznego. Dla umożliwienia korelacji wyników, uzyskanych obiema technikami, wykonana została...
-
Estimation of the excitation variances of speech and noise AR-models for enhanced speech coding
Publication -
Decoding of the FSK signal with noise and distortion with the use of coefficients of the time-frequency transform.
PublicationStreszczenie: Przeanalizowano sygnał z modulacją FSK wykorzystując metodę transformacji czasowo-częstotliwościowej różniące się sposobem podziału płaszczyzny TF na atomy: krótko-okresowej transformacji Fouriera, transformacji falkowej i transformacji pakietami falkowymi. Transformacja falkowa zapewnia dobrą lokalizację czasową zakłóceń o wielkiej częstotliwości, podczas gdy transformacja pakietami falkowymi zapewnia dobrą lokalizację...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublicationTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Modeling the effect of electric vehicles on noise levels in the vicinity of rural road sections
PublicationNumerous European countries experience a steady increase in the share of electric (EV) and hybrid electric (HEV) vehicles in the traffic stream. These vehicles, often referred to as low- or zero-emission vehicles, significantly reduce air pollution in the road environment. They also have a positive effect on noise levels in city centers and in the surroundings of low-speed roads. Nevertheless, issues related to modeling noise from...
-
The noise-induced harmful effect assessment based on the properties of the human hearing system
PublicationA new way of assessment of noise-induced harmful effects on human hearing system is presented in the paper. The method takes into consideration properties of the human hearing system. The pro-posed method determines the cumulative impact on hearing system produced by the excessive noise. Based on the predicted effects of the noise exposure, the new types of noise indicators were developed. The evaluation of these indicators was...
-
ESTIMATION OF NONSTATIONARY HARMONIC SIGNALS AND ITS APPLICATION TO ACTIVE CONTROL OF MRI NOISE
PublicationA new adaptive comb filtering algorithm, capable of tracking the fundamental frequency and amplitudes of different frequency components of a nonstationary harmonic signal embedded in white measurement noise, is proposed. Frequency tracking characteristics of the new scheme are studied analytically, proving (under Gaussian assumptions and optimal tuning) its statistical efficiency for quasi-linear frequency changes. Laboratory tests...
-
Performance Analysis of the "Intelligent" Kirchhoff- Law - Johnson-Noise Secure Key Exchange
PublicationThe Kirchhoff-law - Johnson-noise (KLJN) secure key distribution system provides a way of exchanging theoretically secure keys by measuring random voltage and current through the wire connecting two different resistors at Alice’s and Bob’s ends. Recently new advanced protocols for the KLJN method have been proposed with enhanced performance. In this paper, we analyze the KLJN system and compare with the „intelligent” KLJN (iKLJN)...
-
Multimedia System for Environmental Noise Monitoring. [Multimedialny System Monitorowania Hałasu Środowiskowego]
PublicationIntroductionNumerous reports relating to noise threats in Poland indicate that they occur commonly. The noise has an enormous impact on the health and life quality of the human beings. Noise pollution in Poland is greater than in others UE countries, moreover it has been increased recently. Taking into account 2002/49/WE directive related to the control and assessment of environmental noise a necessity of monitoring these threats...
-
Noise spectral density computation based on finite element model of piezoceramic sensor
PublicationThe high sensitivity with wide bandwidth is required for sensor applications in non-destructive testing (NDT). The sensitivity of piezoceramic sensors demands to minimize their noise especially thermal noise, polarisation noise and low frequency 1/f noise,which are the main sources of voltage or current fluctuation in this sort of sensors. For simplicity, only the piezoceramic part of sensor was under study. the theoretical and...
-
Determination of magnetisation conditions in a Double-Core Barkhausen Noise measurement set-up
PublicationThe magnetic Barkhausen effect is useful forassessing 1D and 2D stress states of ferromagnetic steelobjects. However, its extension to technically importantmaterials, such as duplex anisotropic steels, remains challenging. The determination of magnetisation inside the studied object and the electromagnet for various geometries, materials and magnetisation angles is a key issue.Three-dimensional, dynamic finite element analysis...