Filters
total: 1330
filtered: 1140
displaying 1000 best results Help
Search results for: SUPERDUPLEX STEEL
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublicationRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Formulation of spectral truss element for guided waves damage detection in spatial steel trusses
PublicationW pracy przedstawiono sformułowanie wielowęzłowego elementu spektralnego oraz odpowiedniego schematu całkowania ukierunkowanego na problem propagacji fal w kratownicach przestrzennych o dowolnej geometrii. Zaproponowane podejście nie ogranicza liczby węzłów w elemencie kratowym. Porównawcze rozwiązania numeryczne przeprowadzono dla konstrukcji idealnej (w stanie nieuszkodzonym) oraz dlakonstrukcji z miejscową nieregularnością w...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublicationThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublicationThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
Investigation on Damage-Involved Structural Response of Colliding Steel Structures during Ground Motions
PublicationEarthquakes are the most unpredictable damaging loads which can affect civil engineering structures. Due to insufficient separation distance between adjacent structures with different dynamic properties, structural collisions may occur during ground motions. Although the research on structural pounding has recently been much advanced, the studies have mainly been conducted for concrete structures. The aim of this paper is to show...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublicationThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Determination of Complex Permeability of Silicon Steel for Use in High-Frequency Modeling of Power Transformers
Publication -
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
Publication -
Prediction of the Mechanical Properties of P91 Steel by Means of Magneto-acoustic Emission and Acoustic Birefringence
PublicationThe paper describes an application of nondestructive volumetric magnetic and ultrasonic techniques for evaluation of the selected mechanical parameter variations of P91 steel having direct influence on its suitability for further use in critical components used in power plants. Two different types of deformation processes were carried out. First, a series of the P91 steel specimens was subjected to creep and second, one to plastic...
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublicationThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublicationAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
Aspects of intergranular corrosion of AISI 321 stainless steel in high-carbon-containing environments
PublicationPurpose – The purpose of this paper is to present a case study of unexpected sensitization to intergranular corrosion of highly resistant AISI 321 steel in petrochemical conditions, where it was subjected to the simultaneous influence of elevated temperature of 250°C and vapors from the asphalt production process. Design/methodology/approach – Corrosion coupons were exposed in an installation carrying asphalt vapors. To identify...
-
Influence of plastic deformation on stray magnetic field distribution of soft magnetic steel sample
PublicationThe effect of various combinations of conditions, i.e., presence of the Earth’s magnetic field during and after deformation on the distribution of stray magnetic field of S355 steel sample, which is locally deformed, was investigated. Some of the stages of the experiment were carried out in zero magnetic field. Compensation of the Earth’s magnetic field was obtained by the application of a pair of Helmholtz coils. These coils are...
-
Influence of cavitation intensity on the relative cavitation resistance of laser processed C45 carbon steel
PublicationPraca przedstawia badania względnej odporności kawitacyjnej we wstępnym okresie niszczenia laserowo przetopionej 6 kW laserem CO2 stali C45. Badania odporności kawitacyjnej wykonano na stanowisku z wirującą tarczą. Na erodowanej przetopionej warstwie powierzchniowej określono trzy obszary o różnej intensywności oddziaływania obciążeń kawitacyjnych. Określano wielkość odkształceń plastycznych w analizowanych obszarach, spowodowanych...
-
Influence of H2S on degradation of 9Cr-1Mo steel in advanced stage of metal dusting process
PublicationPrzedstawiono wyniki badań stali 9Cr-1Mo w zaawansowanym stadium procesu pylenia metalu po 10 latach eksploatacji w piecu rafineryjnej instalacji platformingu CCR, przeprowadzonych w celu podjęcia decyzji o dozowaniu związków siarki do wsadu instalacji. Na podstawie długotrwałej ekspozycji próbek stali w 600C w mieszaninie wodoru i siarkowodoru wykazano, że siarka może być powodem procesów wpływających niekorzystnie na stan materiału...
-
Use of electrochemical methods to examine different surface preparation methods for organic coatings on steel
PublicationObróbka strumieniowo - ścierna jest jedną z powszechnie stosowanych metod przygotowania powierzchni. Wśród nowoczesnych metod coraz większe zainteresowanie wzbudza przygotowanie powierzchni wodą pod wysokim ciśnieniem (z ang. waterjetting). W porównaniu z konwencjonalnymi metodami ''waterjetting'' jest nowoczesną oraz przyjazną środowisku metodą. W literaturze brakuje informacji na temat skuteczności owej metody do zastosowań...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublicationIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Assessment of fitness for service of Cr-Mo steel tubes in catalytic reforming charge heaters
PublicationIn this paper characteristic features of metal dusting corrosion in high temperature gas mixtures of high carbon activity in catalytic reforming units, including Continuous Catalyst Regeneration (CCR) platformer are presented. Examples of 2.25Cr-1Mo and 9Cr-1Mo steel tubes at advanced stages of metal dusting process after long-term service in charge heaters are used to prove that destructive examinations are necessary to provide...
-
Concept of cavitation erosion assessment of austenitic 1.4301 stainless steel based on roughness development
Publication -
Non-linear strain rate analysis of earthquake-induced pounding between steel buildings
PublicationPast and recent earthquakes have shown that ground motions may cause severe structural damage to civil engineering structures. Earthquake-induced pounding between adjacent buildings has been identified as one of the reasons which intensifies damages. The aim of this paper is to show the results of the detailed nonlinear FEM analysis of earthquake-induced pounding between two steel buildings. The elastic – perfectly plastic material...
-
Stainless steel/yttria stabilized zirconia composite supported solid oxide fuel cell
PublicationW tym artykule opisano wytworzenie i przebadanie kompozytowych elementów nośnych tlenkowych ogniw paliwowych. Podłoża nośne zostały wytworzone ze stali nierdzewnej i tlenkiem itru stabilizowanego tlenku cyrkonu (YSZ), których proszki zmieszano w różnych proporcjach objętościowych. Zachowanie podłoży podczas spiekania (skurcz liniowy, porowatość) oraz wysokotemperaturowe właściwości (odporność na utlenianie, przewodność elektryczna)...
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublicationThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Specific risks for local stability and capacity of verticat doble - shell cylindrical steel tanks
PublicationOmówiono zagrożenia stateczności i nosności płaszczy zbiorników dwupłaszczowych wywołane przez: niefachowo prowadzoną próbę wodną, dużną różnicę temperatury podczas eksploatacji oraz nierównomierne osiadanie. W księdze konferncyjnej opublikowano dwustronicowe streszczenie referatów a na załączonej płycie referaty zamieszczone są w całości. Liczby podane w nawiasach dotyczą ilości rysunków fotografii na płycie , liczby bez nawiasów...
-
Instantaneous impedance evaluation of dissolution of aisi 304 stainless steel during intergranular corrosion
PublicationCelem pracy było uzyskanie informacji dotyczących zróżnicowania parametrów elektrycznych uzyskanych na podstawie zarejestrowanych chwilowych widm impedancyjnych w zakresie aktywacji i reaktywacji roztwarzania wysokostopowej stali austenitycznej AISI podczas postępującego procesu korozji międzykrystalicznej. Badania prowadzono z wykorzystaniem dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). Pomiary wykonywano ''on-line''...
-
Experimental and numerical study on deformed steel columns subjected to impact load during earthquakes
PublicationThe soft-storey failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an upper soft storey of a structure results in large impact load acting on the lower floors and if the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of the whole building. The aim of the present paper is to investigate the dynamic behaviour...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublicationIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes: numerical analysis
PublicationIt has been observed during earthquakes that the so called soft-storey failure of an upper floor of a building leads to considerable vertical impact load acting on structural members of the lower storeys. The aim of this paper is to investigate numerically the behaviour of horizontally deformed columns (deformation as the result of earthquake loading) that are additionally subjected to vertical impact load. In the first stage of...
-
Nonequilibrium thermodynamic model of diffusion processes in the steel - carbon thin film tribological system
Publication -
Influence of modes of thermal hardening and the subsequent cryogenic processing on structure and properties of steel 38Ni3CrMoV
Publication -
Effect of bending-torsion on fracture and fatigue life for 18Ni300 steel specimens produced by SLM
PublicationIn this study, different fracture surfaces caused by fatigue failure were generated from 18Ni300 steel produced by selective laser melting (SLM). Hollow round bars with a transverse hole were tested under bending-torsion to investigate the crack initiation mechanisms and fatigue life. Next, the post-failure fracture surfaces were examined by optical profilometer and scanning electron microscope. The focus is placed on the relationship...
-
Tool Life and Process Dynamics in High Speed Ball End Milling of Hardened Steel
Publication -
Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
Publication -
The Effect of a Gear Oil on Abrasion, Scuffing, and Pitting of the DLC-Coated 18CrNiMo7-6 Steel
Publication -
Investigations on surface induced tribological characteristics in MQCL assisted machining of duplex stainless steel
Publication -
Multivariate analysis of impedance data obtained for coating systems of varying thickness applied on steel
PublicationElectrochemical impedance spectroscopy (EIS) has proven to be a valuable test method for the electrochemical characterization of protective coatings on metals. The common way of analysis in impedance spectroscopy is to model the impedance spectrum by means of an equivalent circuit and to extract the quantity of interest using optimization techniques. A model, corresponding to the behavior of the sample under testing, is important...
-
Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application
PublicationTo reduce costs and improve high-temperature performance in Advanced Ultra Super Critical (AUSC) boilers, it is necessary to weld austenitic steel to Inconel alloy. In this study, the autogenous tungsten inert gas (TIG) welding process was used to join Alloy 617 and an austenitic AISI 304H steel plate of thickness 5 mm. Microstructural analysis showed that the microstructure formation was uneven along the weldments, with columnar...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublicationLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
Seismic probabilistic assessment of steel and reinforced concrete structures including earthquake-induced pounding
PublicationRecent earthquakes demonstrate that prioritizing the retrofitting of buildings should be of the utmost importance for enhancing the seismic resilience and structural integrity of urban structures. To have a realistic results of the pounding effects in modeling process of retrofitting buildings, the present research provides seismic Probability Factors (PFs), which can be used for estimating collision effects without engaging in...
-
Comparision of two numerical methods for buried steel culverts made of corrugated shell sheets.
PublicationW pracy omawia się dwie metody analizy statycznej obudowy tuneli i przepustów dużej średnicy. Pierwsza z nich, metoda sprężyn polega na modelowaniu ośrodka gruntowego radialnymi sprężynami reprezentującymi odkształcalność gruntu. Drugie podejście oparte jest na zastosowaniu metody elementów skończonych i programu SOFISTIC. W układzie obudowa - grunt obudowę modeluje się zwykłymi ramowymi elementami sprężystymi a otaczający...
-
Fatigue tests of steel Sandwich panel. Fifth International Conference on Marine Technology and Transportation.
PublicationW referacie przedstawiono wyniki badań laboratoryjnych paneli SANDWICH prowadzonych w Katedrze Technologii Okrętów, Systemów Jakości i Materiałoznawstwa Wydziału OiO na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów w wynikami prezentowanymi w literaturze.
-
Numerical calculations of wall pressures and stresses in steel cylindrical silos with concentric and eccentric hoppers
PublicationArtykuł przedstawia numeryczną analize naprężeń w płaszczu silosa. Porównane zostały wyniki dla silosów o przepływie centrycznym i mimośrodowym.
-
Complementary study with magnetic and acoustic techniques of A336 steel damage state due to creep
PublicationBadano możliwość detekcji w sposób nieniszczący zmian w mikrostrukturze stali A336 poddanej próbie pełzania. Testowano dwie magnetyczne techniki (klasyczny efekt Barkhausena i emisję magnetoakustyczną) oraz dwie nowe techniki ultradźwiękowe (pomiar współczynnika elasto-akustycznego oraz dwójłomność akustyczną). Wykazano, iż wyniki badań akustycznych są komplementarne do wyników badań magnetycznych.
-
Specific risks for local stability and capacity of verticat doble - shell cylindrical steel tanks
PublicationOmówiono zagrożenia stateczności i nosności płaszczy zbiorników dwupłaszczowych wywołane przez: niefachowo prowadzoną próbę wodną, dużną różnicę temperatury podczas eksploatacji oraz nierównomierne osiadanie. W księdze konferncyjnej opublikowano dwustronicowe streszczenie referatów a na załączonej płycie referaty zamieszczone są w całości.
-
Simulation of fracture process in concrete elements with steel fibres using discrete lattice model
PublicationArtykuł omawia wyniki modelowania procesu zarysowania w elementach betonowych zawierające stalowe włókna przy zastosowaniu dyskretnego modelu kratownicowego. Beton był modelowany na poziomie mezoskali z uwzględnieniem 5 faz: kruszywa, zaczynu cementowego, włókien i obu stref kontaktu. Obliczenia wykonano dla jednoosiowego ściskania, jednoosiowego rozciągania i zginania prostego.
-
Full-scale experiments on wheat flow in steel silo composed of corrugated walls and columns
PublicationArtykuł omawia wyniki doświadczalne w dużej skali odnośnie przepływu pszenicy w stalowym silosie wykonanym z blachy falistej i słupów. Pomierzono napory poziome i pionowe na ścianie oraz siły pionowe w słupach. Zbadano rodzaj przepływu w zależności od położenia wylotu. Wyniki naporów porównano z Eurokodem.
-
Effect of steel fibres on concrete behavior in 2D and 3D simulations using lattice model.
PublicationW artykule przedstawiono wyniki numerycznej symulacji betonu zbrojonego włóknami stalowymi. Beton został opisany w skali mezo jako materiał 3-fazowy przy zastosowaniu modelu sieciowego. Obliczenia wykonano dla rozciągania jednoosiowego. Porównano ze sobą wyniki dwu- i trójwymiarowe.
-
Experimental and numerical investigations of size effects in reinforced concrete beams with steel or basalt bars.
PublicationW artykule przedstawiono wyniki obliczeń efektów skali w belkach betonowych zbrojonych prętami stalowymi i bazaltowymi podczas zginania. Zastosowano model sprężysto-plastyczny z nielokalnym osłabieniem. Rozkład wytrzymałości na rozciąganie był stochastyczny – przestrzennie skorelowany. Belki były geometrycznie podobne. Wyniki porównano z modelem efektu skali Bazanta
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
IMPACT-TOUGHNESS INVESTIGATIONS OF DUPLEX STAINLESS STEELS
PublicationDuplex stainless steels are very attractive constructional materials for use in aggressive environments because of their several advantages over austenitic stainless steels. Duplex steels have excellent pitting and crevice corrosion resistance, are highly resistant to chloride stress-corrosion cracking and are about twice as strong as common austenitic steels. Better properties are associated with their microstructures consisting...