Filters
total: 1289
filtered: 1173
displaying 1000 best results Help
Search results for: CONONSOLVENCY PHENOMENON
-
Formation of High Corrosion Resistant Nanotubular Layers on TitaniumAlloy Ti13Nb13Zr
PublicationThis paper presents results of oxidation tests and corrosion investigations of titanium alloy Ti13Nb13Zr performed at different conditions. The oxide layers have been formed by electrochemical method in 2M H3PO4 + 0.3% HF solution for 30 min. and 1 h at 20 V constantvoltage. The corrosion tests have been made by potentiodynamic method in Ringer`s solution at pH ranged between 3 and 7. It has been shown that the nano-oxide films,...
-
Degradation of Gel-Coat Layer in Glass/Polyester Laminate in Seawater Environment
PublicationGlass/polyester laminate coated with gelcoat layer of different thickness 0,5; 1,5; 3 mm was studied in terms of blistering behaviour and water sorption in hot water environment. Blistering was found to be accelerated for thin (0,5 mm) gel-coat layer compared to the thick (1,5; 3 mm), however no significant difference in blistering behaviour was observed between the laminates with gel-coat thickness 1,5 and 3 mm which may suggest...
-
Effects of Laser Remelting at Cryogenic Conditions on Microstructure and Wear Resistance of the Ti6Al4V Alloy Applied in Medicine
PublicationThe titanium and its alloys can be subjected to surface treatment, including laser treatment. In this work a new laser treatment at cryogenic conditions of Ti6Al4V alloy has been described. The work has been aimed at establishing whether such surface treatment could be suitable for implants working under wear in biological corrosive environment. The remelting has been made with the use of CO2 continuous work laser at laser power...
-
Environmental Degradation of Engineering Materials & Materials Engineering and Technologies
Publication -
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Determination of Failure Causes of a Steam Turbine Casing
PublicationThe paper presents results of research and failure analysis undertaken to determine failure causes of a steam turbine casing. After 130,000 hours of service the crack in a outer shell of the turbine casing was found. The inner shell of the casing was made of cast steel grade G21CrMoV5-7, and the outer shell of grade G20CrMo4-5. Following research were performed in order to determine causes of the casing failure: chemical analysis;...
-
The Effect of Welding Conditions on Diffusible Hydrogen Content in Deposited Metal
PublicationThe article presents the results of a literature survey and preliminary tests which set out effects of welding conditions on the amount of diffusible hydrogen in deposited metal. Experiments were conducted by using rutile coated electrodes which generate high contents of diffusible hydrogen in deposited metal. The amount of diffusible hydrogen was determined by a glycerin test.Eleven factors were considered: the electrode angle,...
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublicationResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
Effect of crystallization process at cryogenic conditions on the functional properties of the SUPERSTON alloy used in production the ship's propellers
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the SUPERSTON alloy used for ship's propellers. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. During the laser remelting at cryogenic conditions the microstructure changes significantly. This is related to synergistic effects of the solidification rate, phase transformations...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
Oxidation Time Influence on the Structure of the Cobalt Base Clad Layer and Scale Morphology
PublicationZbadano wpływ czasu utleniania na mikrosrukutręi własności mechaniczne a w szczególności mikrotwardość, warstw wykonanych ze stopu kobaltu.Warstwy były wykonane za pomocą napawania plazmowego (PTA). Stop kobaltu podlegał utlenianiu w powietrzu w temperaturze 800 topni celsjusza w czasie 1, 22 i 200 godzin. w wyniku utleniania nastapiło uformowanie warstw zgorzeliny oraz nastapiły zmiany w mikrostrukturze. Zaobserwowano także zmiany...
-
Wear and corrosion characteristics of the layers type (mn-p) formed on aluminium alloys
Publicationopisano multipleksową metodę wytwarzania warstw zawierających mangan i fosfor (mn-p) na stopach aluminium. przedstawiono wyniki badań mikrostruktury, właściwości tribologicznych i korozyjnych tych warstw. stwierdzono obecność tlenku manganu i fosforku manganu w wytworzonych warstwach oraz ich wysoką twardość, rzędu 1272 hv0,02. warstwy typu (mn-p) zmniejszają podatność stopu alsi13mg1cuni na korozję w 0,01 mh2so4.
-
Indoor atmospheric degradation of historical metal objects studied by spectroscopic techniques
Publication -
Perovskites in Solid Oxide Fuel Cells
PublicationPrzeglądowa publikacja dotycząca wykorzystania ceramicznych materiałów perowskitowych w tlenkowych ogniwach paliwowych.
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Deformation of the Structural Details of the Components Created by the Rapid Prototyping Method
PublicationThe paper present the results of preliminary research and describes the deformation of construction details within the process of producing small element employing a stereography system. The article discuses a scheme for changes in data conversion. Variation in construction details have been described on the basis of analysing photographs.
-
Hardened Steel Surface Waviness Created by Rolling Burnishing Process
PublicationThe surface of the finishing machined parts is defined mainly by roughness parameters. Growing demands on the part, especially mating sliding or rolling, require the specification of additional parameters, such as waviness parameters, particularly when there is significant resistance to seizing or noise reduction. This paper presents surface waviness characteristics of hardened burnished steel.
-
The Roughness of the Hardened Steel Surface Created by the Rolling-Burnishing Process
PublicationBurnishing hard materials can be used as an alternative finishing process. this paper presents the results of burnishing hardened steel. The article discusses surface deformation that occurs during this process and depends on the selected parameters of the geometric structure of the force applied for surface burnishing.
-
Preparation and characterization of TiO2 nanostructures for catalytic CO2 photoconversion
PublicationThe titanium dioxide target (99.7%) of 1 cm in dia was ablated in vacuum by laser pulses(6 ns) at 266 nm and at repetition rate of 10 Hz. During deposition the laser fluence between 1 and 3.5 J/cm2 and the O2 pressure from the range of 10-2 - 1 Pa were applied. The thin TiO2 films were deposited on glass substrate (1 × 1 cm2) heated up to 500 °C. The chemical composition of the film and samples produced by annealing were investigated...
-
Influence of spatial structures of 316L stainless steel on its cavitation erosion resistance
Publication -
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublicationDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
The Characteristic of Surface Layers on Austenitic Stainless SteelAfter Glow-discharge Nitriding Process.
PublicationThis paper presents investigation of surface layers. The diffusion layers were produced by using different parameters of reactive atmosphere (N2:H2). The research of the surface layers was performed using scanning electron microscope (SEM). The results of energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD) analysis are presented. Research reveals the influence of chemical constitution of reactive atmosphere on the...
-
The Effect Fabrication Method of Cobalt Base Clad Layer On Air Oxidation
PublicationNapawane warstwy ze stopu kobaltu zostały wykonane za pomocą napawania plazmowego (PTA) oraz laserowego. Zostały one poddane utlenia niu w temperarurze 1100 stopni celsiusza prze 200 godzin. Przeprowadzono badania mikrostruktury i składu chemicznego warstwy tlenkowej oraz głębszych warstw napoiny. Nie stwierdzono wpływu metody wytwarzania na skutki procesu utleniania.
-
Simulation and Experiments of High Speed Machining Vibration Monitoring with Variable Spindle Velocity
PublicationArtykuł poświęcony jest nadzorowaniu drgań wirujących narzędzi podczas obróbki szybkościowej na nowoczesnych centrach frezarskich. Przeprowadzono analizę dynamiki procesu skrawania smukłym frezem kulistym. W celu zredukowania drgań zastosowano, z powodzeniem, zmienną prędkość obrotową narzędzia. Badania symulacyjne dotyczące efektywności proponowanej metody zostały potwierdzone wynikami badań eksperymentlanych na frezarce Alcera...
-
Application of Syntactic Pattern Recognition Approach in Design and Optimisation of Group Machining Systems
PublicationRozwinięto koncepcję budowy zoptymalizowanych struktur systemów wytwarzania grupowego spektrum części z wykorzystaniem modelu analizy syntaktycznej sekwencji operacji ich procesów technologicznych. Określono formułę metryki odległościowej opisu stopnia zróżnicowania marszrut indywidualnych procesów oraz testowano jej skuteczność w aspekcie eksploracji wielowymiarowych danych i klasteryzacji obiektów wg cech wymagań technologicznych....
-
Cobalt Base Clad Layer Resistance On The Corrosion Under Low Sulfur Preassure
PublicationNapawane laserowo warstwy ze stopu kobaltu, zostały poddane siarkowaniu przy niskich ciśnieniach cząstkowych w temperaturze 800 stopni celsiusza prze 24 godziny. Uzyskano warstwę zgorzeliny zróżnicowaną w zależności od zastosowanego ciśnienia. W obu jednak przypadkach podobne były zmiany zachodzące w warstwie po zgorzeliną - degradacja węglików i intensywna korozja wzdłuż granic dendrytów.
-
Influence of cavitation intensity on the relative cavitation resistance of laser processed C45 carbon steel
PublicationPraca przedstawia badania względnej odporności kawitacyjnej we wstępnym okresie niszczenia laserowo przetopionej 6 kW laserem CO2 stali C45. Badania odporności kawitacyjnej wykonano na stanowisku z wirującą tarczą. Na erodowanej przetopionej warstwie powierzchniowej określono trzy obszary o różnej intensywności oddziaływania obciążeń kawitacyjnych. Określano wielkość odkształceń plastycznych w analizowanych obszarach, spowodowanych...
-
Cavitation Erosion Resistance of Austenitic Microstructure Created byLaser Beam
PublicationPraca przedstawia własności kawitacyjne różnych mikfrostruktur austenitycznych tworzonych za pomocą wiązki lasera na stalach X5CrNi18-10 oraz C45. Stal X5CrNi18-10 była laserowo stopowana węglikiem TiC oraz stopowana Ni, Mn, Cr i Nb. Jako żródło mocy stosowany był laser CO2. Własności kawitacyjne oceniane były na stanowisku z wirującą tarczą. Badania ujawniły różną podatność struktury austenicycznej do odkształceń plastycznych...
-
Generation of Optimal Process Plan Alternatives for ManufacturingMechanical Components
PublicationOmówiono aktualny stan wiedzy dotyczący wykorzystania systemów komputerowo wspomaganego projektowania procesów technologicznych - CAPP. Przedstawiono problemy związane z integracją systemów CAPP z systemami CAD. Omówiono założenia dla generowania optymalnych wariantów procesów wytwarzania z zastosowaniem modułów technologicznych tzw. features, wg metody gałęzi i ograniczceń (ang. branch-and-bound).
-
Modelling of Ship’s Heeling and Rolling for the Purpose of Gantry Control Improvement in the Course of Cargo Handling Operations in Sea Ports
PublicationThe paper presents two proposals of models of interaction between a ship and cargo being loaded or discharged by a gantry in port, in terms of heeling and rolling of the vessel. The main purpose of such modelling is the need for improvement of gantry control with regard to faster operations thanks to more accurate estimation of level and moment of cargo release from a gantry hook or spreader. The study may be the contribution to...
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublicationThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Materials Design for the Titanium Scaffold Based Implant
PublicationThe main objective of here presented research is a design the scaffold/porous titanium(Ti) alloy based composite material demonstrating better biocompatibility, longer lifetime andbioactivity behaviour for load-bearing implants. The development of such material is proposed bymaking a number of consecutive tasks. Modelling the mechanical, biomechanical and biologicalbehavior of porous titanium structure and an elaboration of results...
-
Optimization of Self-Organized TiO2 Nanotube Geometry on Ti and Ti Alloys Using Fuzzy Logic Reasoning
PublicationThe geometry of self-organized TiO2 nanotubes, obtained by electrochemicalanodization, has been determined by using fuzzy reasoning approach. The efficiency of TiO2nanotubular layer in biomedical applications depends on geometry and available surface area ofnanotubes, which can be determined by their diameter and length. The structure of nanotubesdepends on processing parameters of electrochemical anodization, like applied potential,anodization...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Using River Formation Dynamics Algorithm in Mobile Robot Navigation
PublicationRiver Formation Dynamics is a heuristic optimization algorithm based on the manner, in which drops of water form the river bed. The idea is to imitate the movement of drops on the edges between given nodes thus performing a search based on their height, which is modified through the mechanism of soil erosion and sediment deposition. In this way decreasing gradients are constructed, and these are followed by subsequent drops to...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublicationIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Studies of the Modelling Accuracy of Steam Turbine Control Systems for Diagnostic Tests of Automatic Synchronizers
PublicationOne of the important factors that affect the reliable operation of the power system and the rapid restitution after disaster is a quick and effective combining synchronous electric power facilities to operate in parallel. Hence, diagnostics of automatic synchronizers at every stage of their life, from building a prototype, through the whole life, until removing such devices from the operation, is an extremely important and responsible...
-
The Optimal Spindle Speed Map for Reduction of Chatter Vibration During Milling of Bow Thruster Blade
PublicationW artykule przedstwiono przykład wykorzystania procedury tworzenia mapy optymalnych prędkosci obrotowych w celu ograniczenia drgań samowzbudnych podczas frezowania płata śruby okrętowego steru strumieniowego.
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublicationAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Phase investigations of copper based CuZn38Al2MnFe alloy
PublicationW pracy przedstawiono analizę fazową mosiądzu CuZn38Al2MnFe. Wykazano, że obecność fazy Fe4Mn77Si19 powoduje kruchość stopu w teście zginania próbek.
-
Influence of geotechnical conditions on damage states of Gdansk Bay Coast cliff formations
PublicationA geotechnical aspect of destruction processes of seashores was identified based on the case of erosion of Gdansk Bay Coast cliff formations. Causative factors of landslide were described in the context of natural phenomena, land development and its anthropogenic transformations. Possible directions of theoretical analysis of changes in groundwater relations were indicated.
-
Wskaźnik przedsiębiorczości w jednostkach terytorialnych Polski – zróżnicowanie w czasie i przestrzeni
PublicationPrzedmiotem artykułu jest analiza zjawiska prowadzenia działalności gospodarczej przez osoby fizyczne, mierzonego poprzez wskaźnik liczby tych osób na 100 osób w wieku produkcyjnym. Wskaźnik ten nazywany jest nieraz wskaźnikiem przedsiębiorczości, mimo, że mierzy tylko jeden z jej przejawów. Badania prowadzono w układzie podregionów, powiatów i gmin (według ich rodzaju, z wyodrębnieniem miast w gminach miejsko-wiejskich). Celem...
-
Synagogi dawnej Polski - ich teraźniejszość i przyszłość
PublicationTekst stanowi próbę ujęcia w szerszej perspektywie złożonego zjawiska zmiany formy użytkowania ocalałych obiektów kultu religijnego. Postępująca sekularyzacja współczesnych społeczeństw stanowi wyzwanie dla religijnych społeczności różnych wyznań, przynosząc również pytania dotyczące zmiany przeznaczenia pustoszejących świątyń. Biorąc pod uwagę społeczny kontekst zarysowany powyżej, ocalałe budynki synagog można uznać za odrębny,...
-
Synchronic digital stereophotography and photogrammetric analyses in monitoring the flow of liquids in open channels
PublicationThe authors present the results of their research into photogrammetric documents based on synchronic digital images. Examples presented in the paper indicate the value of synchronic stereophotography in registering phenomena connected with liquids. Combining synchronic stereophotography with photogrammetric methods has allowed the authors to develop an application useful for monitoring the flow of a liquid in an open channel.
-
AN OVERVIEW OF HEAT TRANSFER ENHANCEMENT BASED UPON NANOPARTICLES INFLUENCED BY INDUCED MAGNETIC FIELD WITH SLIP CONDITION VIA FINITE ELEMENT STRATEGY
PublicationThe mathematical model of heat generation and dissipation during thermal energy transmission employing nanoparticles in a Newtonian medium is investigated. Dimensionless boundary layer equations with correlations for titanium dioxide, copper oxide, and aluminium oxide are solved by the finite element method. Parameters are varied to analyze their impact on the flow fields. Various numerical experiments are performed consecutively...
-
Simulation of the Remanence Influence on the Transient States of the Single-Phase Transformer Including Feedback Preisach Model
PublicationThis paper presents the results of the experimental and simulation investigation concerning the influence of remanence in the core of a single-phase transformer at the no-load transient state. Experimental studies consisted of the discharge of the capacitor through the primary winding at several different values of the residual magnetic flux. The paper presents a model of the transformer test system, taking into account the magnetic...
-
Representation of magnetic hysteresis in tape wound core using feedback Preisach model
PublicationThis paper presents a mathematical model for the hysteresis phenomenon in ferromagnetic tape wound core. The feedback scalar Preisach model of hysteresis is used to simulate magnetic behavior of the grain oriented silicon strip of ET114-27 type. Determination of B-H hysteretic curve is based on measurement of the initial magnetization curve and the main hysteresis loop. The Preisach distribution function (PDF) of ET114-27 material...
-
Stability analysis of a dike constructed of anthropogenic materials
PublicationNumerical analyses of stability are presented for a hypothetical dikes constructed of dredged materials and bottom ash, in varying proportions. The paper is related to the international research project DredgDikes, which focused on the use of anthropogenic materials in dikes construction and flood protection. The aim of this project was to investigate the possibility of using anthropogenic materials from rivers and sea dredging...