displaying 1000 best results Help
Search results for: SHELL CORROSION
-
An investigation of microstructural basis for corrosion behavior of Al-CNT composites fabricated by SPS
PublicationIn this research effect of the addition of multi-wall carbon nanotubes (MWCNTs) as additive powder on microstructure and corrosion behavior of fabricated Al-CNT composites was studied. The aluminum powder and CNTs were mixed with high energy planetary ball-mill. It is observed that by increasing milling time, the uniformity of CNTs on aluminum matrix and consequently corrosion resistance of Al-CNT composite is increased. On the...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublicationTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
Experimental ultimate strength assessment of stiffened plates subjected to marine immersed corrosion
PublicationThis study experimentally analyses the impact of marine immersed corrosion degradation on the compressive strength of the stiffened plates where the lower degradation levels were considered. The corrosion degradation test was accelerated by controlling the natural corrosion environmental factors, avoiding applying an electric current. Different groups of corrosion degradation levels and initial plate thicknesses were investigated....
-
Indoor accelerated controlled corrosion degradation test of small- and large-scale specimens
PublicationThe work presented here is a part of a long-term project analysing the structural behaviour of ageing marine structures. An accelerated corrosion degradation set-up was developed to reproduce corroded marine structural specimens of different degrees of degradation, controlling various natural factors, i.e., temperature, oxygen content, salinity, and flow velocity. The nine stiffened plates of 1.2 m length and 30 small scale specimens...
-
Acoustic Emission Monitoring of Structural Elements of a Ship for Detection of Fatigue and Corrosion Damages
PublicationUszkodzenia korozyjne i pęknięcia zmęczeniowe są głównymi przyczynami defektów strukturalnych we wszystkich środkach transportu takich jak statki, cysterny drogowe i kolejowe. Oba typy degradacji tzn. degradacja materiału i konstrukcji są przedmiotem badań przeprowadzanych w projekcie badawczym VII Programu Ramowego Unii Europejskiej o nazwie ''Monitorowanie efektywnych kosztów korozji i zmęczenia w środkach transportu'' (akronim...
-
Electrochemical Evaluation of Sustainable Corrosion Inhibitors via Dynamic Electrochemical Impedance Spectroscopy
PublicationFinding suitable measurement methods for the effective management of electrochemical problems is of paramount importance, particularly for improving efficiency in corrosion protection. The need for accurate measurement techniques specific to nonstationary conditions has long been recognized, and promising approaches have emerged. This chapter introduces dynamic electrochemical impedance spectroscopy as a novel advancement in electrochemistry...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublicationThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublicationOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Influence of yttria surface modification on high temperature corrosion of porous Ni22Cr alloy
PublicationProtective coatings for porous alloys for high temperature use are relatively new materials. Their main drawback is high temperature corrosion. In this work protective coatings based the on Y-precursor infiltrated into the sintered Ni22Cr alloys are studied at 700°C. Effects of the amount of the protective phase on the resulting corrosion properties are evaluated in air and humidified hydrogen. Weight gain of the samples, their...
-
X-ray Photoelectron Spectroscopy of Carboxylic Acids as Corrosion Inhibitors of Aluminium Alloys
PublicationThe datasets, titled X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media and X-ray Photoelectron Spectroscopy studies of various carboxylic acids adsorption on aluminium alloys in alkaline media, contain XPS studies of the corrosion inhibitory action of selected dicarboxylic acids towards commercially available aluminium alloy 5754 in alkaline media at pH=11. These datasets...
-
Inhibitive effect of sodium molybdate on corrosion of AZ31 magnesium alloy in chloride solutions
PublicationIn this work, corrosion inhibition of the AZ31 magnesium alloy was investigated in NaCl solutions containing different amounts of sodium molybdate inhibitor. Electrochemical, hydrogen evolution, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. The results showed that Na2MoO4 inhibitor provides reliable inhibition at high concentrations (150 mM). Surface examination...
-
CORROSION ENGINEERING SCIENCE AND TECHNOLOGY
Journals -
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Core-shell cobalt particles Co@CoO loaded on nitrogen-doped graphene for photocatalytic water-splitting
Publication -
Influence of different types of the internal system of the ballistic helmet shell on the thermal insulation measured by a manikin headform
Publication -
Core/shell structured Ti/Si/C composite for high-performance zinc-ion hybrid capacitor
Publication -
Recycling of Plastic Wastes for the Mass Production of Yolk–Shell-Nanostructured Co3O4@C for Lithium-Ion Batteries
Publication -
Adsorption of cationic dyes onto Fe@graphite core–shell magnetic nanocomposite: Equilibrium, kinetics and thermodynamics
Publication -
Recycling of Plastic Wastes for the Mass Production of Yolk–Shell-Nanostructured Co3O4@C for Lithium-Ion Batteries
Publication -
Recent Achievements in Constitutive Equations of Laminates and Functionally Graded Structures Formulated in the Resultant Nonlinear Shell Theory
PublicationThe development of constitutive equations formulated in the resultant nonlinear shell theory is presented. The specific features of the present shell theory are drilling rotation naturally included in the formulation and asymmetric measures of strains and stress resultants. The special attention in the chapter is given to recent achievements: progressive failure analysis of laminated shells and elastoplastic constitutive relation...
-
Generalized Taylor formula and shell structures for the analysis of the interaction between geosythetics and engineering structures of transportation lines
PublicationThe analysis of the interaction between geosynthetics and engineering structures (e.g. railroad bed, soil foundation, pipeline) assumes that the geosynthetic form elastic membranes or shell laid on different types of foundations. The mathematical description of that problems in continuous domain employs Laplace operator Δ or d’Alembert operator □. In this paper we demonstrate the analysis based on generalize Taylor formula, and...
-
MARSTRUCT benchmark study on nonlinear FE simulation of an experiment of an indenter impact with a ship side-shell structure
PublicationThis paper presents a benchmark study on collision simulations that was initiated by the MARSTRUCT Virtual Institute. The objective was to compare assumptions, finite element models, modelling techniques and experiences between established researchers within the field. Fifteen research groups world-wide participated in the study. An experiment involving a rigid indenter penetrating a ship-like side structure was used as the case...
-
A higher order transversely deformable shell-type spectral finite element for dynamic analysis of isotropic structures
PublicationThis paper deals with certain aspects related to the dynamic behaviour of isotropic shell-like structures analysed by the use of a higher order transversely deformable shell-type spectral finite element newly formulated and the approach known as the Time-domain Spectral Finite Element Method (TD-SFEM). Although recently this spectral approach is reported in the literature as a very powerful numerical tool used to solve various...
-
Equivalent 4-node enhanced assumed strain and hybrid stress shell elements in 6-parameter theory
PublicationWe discuss the equivalence of semi-enhanced assumed strain (EAS) and semi-hybrid stress (SEM) shell finite elements. We use the general nonlinear 6-field shell theory with kinematics composed of generalized displacements composed of the translation field and the rotation field. Due to the presence of rotation tensor the elements have naturally six nodal engineering degrees of freedom. We propose interpolation for a strain field...
-
Experimental and numerical investigation on shell and coil storage unit with biodegradable PCM for modular thermal battery applications
PublicationThermal energy storage (TES) in automotive applications is currently growing in importance. TES can visibly reduce primary energy consumptions, decrease CO2 emission, and improve thermal comfort in electric as well as hybrid vehicles. However, to meet the new ambitious target (15% reduction of CO2 emissions in the new cars until 2025) it is required to use plug-in electric vehicles. For this reason, this paper focuses on the optimization...
-
Thermodynamic and geometrical characteristics of mixed convection heat transfer in the shell and coil tube heat exchanger with baffles
PublicationThe article presents passive heat transfer enhancement method in the form of baffles to increase the energy efficiency of the shell coil heat exchanger. Conducted literature review shows that, despite numer- ous studies, there is little work on the intensification of heat transfer at the shell side. Most of the work focuses on the impact of geometrical parameters of the coil itself. This article successfully proves that it is possible...
-
Cyclic polarization studies of Mg corrosion in alkaline environment
Open Research DataThe dataset contains the cyclic polarization studies of Mg (99.99%) in NaOH electrolyte at different pH values: 10, 11 and 12 aiming at understanding of Mg(OH)2 passive layer formation mechanism and conditions. The electrochemical studies were carried out in a three electrode setup, with Pt mesh as the counter electrode and Ag|AgCl as the reference...
-
Jacek Ryl dr hab. inż.
PeopleI have obtained my PhD in chemical technology in 2010. In the same year, I was employed at the Department of Electrochemistry, Corrosion and Materials Engineering at the Faculty of Chemistry. In 2018 I received habilitation at the Faculty of Chemistry GUT in technical sciences in the discipline of chemical technology. From 2021, he was employed at the Institute of Nanotechnology and Materials Science at the Faculty of Technical...
-
Numerical analysis of laminated shells under in-plane axial compression
PublicationW pracy analizowana jest stateczność powłoki warstwowej poddanej osiowemu ściskaniu. Badany jest wpływ wariantów uwarstwienia oraz warunków podparcia krawędzi obciążonej na zachowanie konstrukcji. Wyniki numeryczne porównano z eksperymentem.
-
Thermo-elastic non-linear analysis of multilayered plates and shells
PublicationGeometrically nonlinear FEM analysis of multilayered composite plates and shells is performed in order to resolve the stability problem of the structures being under the influence of temperature field. The Riks-Wempner-Ramm algorithm with a specially modified multi-choice unloading condition has been implemented in authors’ numerical code. As the representation of multilayered medium the Equivalent Single Layer approach with the...
-
Elastoplastic nonlinear FEM analysis of FGM shells of Cosserat type
PublicationThe paper is a continuation of [1] where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO) [2] mixture...
-
On shear correction factors in the non-linear theory of elastic shells
PublicationW pracy wyprowadzono analitycznie wartości korekcyjnych współczynników ścinania dla ścinania poprzecznego oraz dla momentów owinięcia w ramach nieliniowej sześcioparametrowej teorii powłok. Wartości wyprowadzono poprzez odpowiednie sformułowanie komplementarnej energii sprężystej. Na drodze analizy przy pomocy MES, badano wpływ wartości współczynników na położenie punktów bifurkacji, deformacje, całkowitą energię sprężystą układu...
-
On continuity conditions at the phase interface of two-phase elastic shells
PublicationW pracy rozwinięto ogólną nieliniową teorię powłok sprężystych podlegających przejściom fazowym typu martenzytowego. Przedstawione sformułowanie oparte jest na statycznie i kinematycznie ścisłym modelu powłokowym. Uwzględniono gęstośc energii odkształcenia, jak również siły i momenty zadane wzdłuż krzywoliniowego przejścia fazowego. W szczególności otrzymano statyczne warunki ciągłości wzdłuż koherentnego połączenia oraz połączenia...
-
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublicationUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
Health monitoring services based on off-the-shelf mobile devices
PublicationDevelopment of health monitoring systems usually involves usage of dedicated devices with provided guarantees in terms of their reliability. Those devices raise the cost of the whole system, because of which such platforms are limited only to specific areas and constrained number of users. Usage of off-the- shelf devices could lower the cost and bring those systems to the masses. The paper covers possible uses of common off-the-shelf...
-
On refined constitutive equations in the six-field theory of elastic shells
PublicationWithin the resultant six-field shell theory, the second approximation to the complementary energy density of an isotropic elastic shell undergoing small strains is constructed. In this case, the resultant drilling couples are expressed explicitly by the stress resultants and stress couples as well as by amplitudes of the quadratic and cubic distributions of an intrinsic deviation vector. The refined 2D strain-stress and stress-strain...
-
Nonlinear material identification of heterogeneous isogeometric Kirchhoff–Love shells
PublicationThis work presents a Finite Element Model Updating inverse methodology for reconstructing heterogeneous materialdistributions based on an efficient isogeometric shell formulation. It uses nonlinear hyperelastic material models suitable fordescribing incompressible material behavior as well as initially curved shells. The material distribution is discretized by bilinearelements such that the nodal values...
-
Investigation effect of benzotriazole on the corrosion of brass-MM55 alloy in artificial seawater by dynamic EIS
PublicationW pracy przedstawiono wyniki badań impedancyjnych otrzymanych podczas ekspozycji stopu MM55 w środowisku sztucznej wody morskiej. Wykazano ścisłą korelację charakterystyk impedancyjnych ze stężeniem benzotriazolu. Przedstawiono czasową ewolucję ochronnego efektu inhibicyjnego.
-
Corrosion resistance evaluation of Al-based alloys by means of dynamic electrochemical impedance spectroscopy
PublicationW pracy przedstawiono wyniki badań stopów aluminium wykonane za pomocą dynamicznej elektrochemicznej spektroskopii. Na podstawie uzyskanych widm impedancyjnych zostały pokazane zmiany parametrów elektrycznego schematu zastępczego z potencjałem. Stwierdzono, że dodatek magnezu do badanego stopu obniża właściwości przeciwkorozyjne stopu.
-
Evaluation of corrosion inhibition of brass -118 in artificial seawater by benzotriazole using dynamic EIS
PublicationPrzedstawiono wyniki korozji mosiądzu 118 w sztucznej wodzie morskiej oraz efekt inhibicyjny benzotriazolu (BTA) przy użyciu nowoczesnej dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). metoda ta pozwala śledzić dynamikę procesu korozyjnego i efektu inhibicyjnego poprzez ocenę parametrów elektrycznych obwodu zastępczego. Chwilowe widma impedancyjne rejestrowane przez 10h wykazują iż ekspozycja przez okres kilku...
-
Effect of Aluminizing on the Fatigue and High-Temperature Corrosion Resistance of Inconel 740 Nickel Alloy
Publication -
DEIS assessment of AISI 304 stainless steel dissolution process in conditions of intergranular corrosion
Publication -
Corrosion resistance evaluation of Al‐based alloys by means of dynamic electrochemical impedance spectroscopy
Publication -
Effect of native air-formed oxidation on the corrosion behavior of AA 7075 aluminum alloys
Publication -
Evaluation of corrosion inhibition of brass-118 in artificial seawater by benzotriazole using Dynamic EIS
Publication -
Effect of chemical composition on corrosion and wear behaviour of the composite Ni-Fe-Al2O3 coatings.
PublicationPrzedstawiono wyniki badań powłoki kompozytowej otrzymanej przez osadzanie katodowe galwaniczne w roztworze zawierającym sole niklu, żelaza oraz cząstki ceramiki Al2O3 o różnej wielkości i stężeniu. Wykazano, że charakterystyka ceramiki posiada wpływ na szybkość korozji i zużycia ściernego. W szczególności, zawartość ceramiki wpływa dodatnio na odporność na zużycie ścierne, ale nieco obniża odporność na zużycie korozyjne.
-
Novel method of initiation stage of stress corrosion cracking monitoring with respect to marine constructions
PublicationKorozja konstrukcji morskich i jednostek pływających stanowi bardzo ważny problem w odniesieniu do aspektów bezpieczeństwa, gdyż w całym okresie eksploatacji narażone są na działanie bardzo agresywnego środowiska i innych czynników eksploatacyjnych. W rezultacie prowadzi to do niespodziewanych kolizji i wypadków. Praca przedstawia zastosowanie dynamicznej elektrochemicznej spektroskopii impedanycjnej (DEIS) do badania inicjacji...
-
Prediction of corrosion fatigue crack propagation life for welded joints under cathodic potentials
PublicationPrzy ochronie katodowej poniżej potencjału optymalnego obserwuje się przyspieszenie propagacji pęknięcia korozyjno-zmęczeniowego w porównaniu do konstrukcji nie chronionej. Zaproponowano własną formułę empiryczną na wpływ potencjału ochronnego na prędkość propagacji pęknięcia oraz własny wzór na [delta]K w złączu pachwinowym. Wyprowadzono wzór na krzywą ''S-Np'' (naprężenie - długość okresu propagacji pęknięcia). Zaprezentowana...
-
Corrosion behaviour of Cr coatings deposited from Cr(III) formate - urea electrolytes
PublicationPowłoki chromowe były otrzymane z elektrolitów Cr(III) zawierających odpowiednie ligandy, zapewniające ich dobry wygląd. Zbadano wpływ hydrazyny oraz hydrohylo aminofosfatu na właściwości korozyjne Cr otrzymanego z kąpieli mocznikowo-formaldehydowych Cr(III). Właściwości warstw testowano przy pomocy metody EIS rejestrując widma impedancyjne dla próbek o różnych czasach ekspozycji w zakwaszonym roztworze siarczanowym ( pH 2,6) stosując...
-
Stress corrosion cracking of the 26H2MF and 34HNM constructional allaysteels of different heat treatment in hydrocarbons
PublicationBadane są dwie stale stopowe 26HZMF i 34HNM o różnych właściwościach mechanicznych w różnych środowiskach.