Jacek Ryl - Dane badawcze

dr hab. inż. Jacek Ryl

Zatrudnienie

Profesor uczelni w Instytut Nanotechnologii i Inżynierii Materiałowej
Kierownik Zakładu w Zakład Elektrochemii i Fizykochemii Powierzchni

Obszary badawcze

seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites liczba: 38

rozwiń zwiń

The electrochemical studies for chitosan hydrogel membranes on glassy carbon substrates
Dane Badawcze
- A. Smułka
- M. Cieślik
- A. Olejnik
- A. Zieliński
- J. Ryl
- T. Ossowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains various electrochemical studies carried out to investigate the preconcentration of [Fe(CN)6]3- ions by chitosan hydrogel membranes coating the glassy carbon electrodes. The glassy carbon electrode (GCE, 3.0 mm diameter) was first polished with Al2O3 powder (0.3 mm) using a polishing kit from Buehler, rinsed with deionized...
The influence of chitosan hydrogel cross-linking by agarose on coating physico-chemical properties
Dane Badawcze
- A. Smułka
- M. Cieślik
- A. Olejnik
- A. Zieliński
- J. Ryl
- T. Ossowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains various physicochemical analyses showing the effect of different concentration of chitosan and the cross-linking agent agarose. Each sample is labeled by C and A representing chitosan and agarose concentrations, respectively, while the exact amounts are depicted in the attached table. Fourier-transform infrared (FT-IR) spectroscopy...
The influence of chitosan hydrogel coating on different redox probes kinetics
Dane Badawcze
- A. Smułka
- M. Cieślik
- A. Olejnik
- A. Zieliński
- J. Ryl
- T. Ossowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains cyclic voltammetry studies of three redox probes: 1 mM K3[Fe(CN)6], [K4Fe(CN)6], C12H14FeO2, and [Ru(NH3)6]Cl2 dissolved in 0.1 M KCl or PBS as the primary electrolyte. The studies are made for glassy carbon electrode (GC) and glassy carbon electrode covered with thin chitosan hydrogel membrane (C2A2). Cyclic voltammograms were...
Raman studies of 3D printed CB-PLA samples after microwave treatment
Dane Badawcze
- K. Kozłowska
- M. Cieślik
- A. Koterwa
- K. Formela
- J. Ryl
- P. Niedziałkowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains Raman spectroscopy analyses of microwave-activated carbon-black doped polylactic acid 3D printed electrodes.
SEM micrographs of 3D printed CB-PLA samples topography after microwave treatment
Dane Badawcze
- K. Kozłowska
- M. Cieślik
- A. Koterwa
- K. Formela
- J. Ryl
- P. Niedziałkowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains the electrochemical studies on microwave-activated carbon-black doped polylactic acid 3D printed electrodes.
SEM micrographs of 3D printed CB-PLA samples topography after microwave treatment
Dane Badawcze
- K. Kozłowska
- M. Cieślik
- A. Koterwa
- K. Formela
- J. Ryl
- P. Niedziałkowski
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains the SEM micrographs of carbon-black doped polylactic acid 3D printed electrodes, after microwave treatment to activate the electrode surfaces. FEI Quanta 250 FEG SEM was used for these analyses. Samples were treated with CEM reactor or microwave oven.
STL files of all-3D-printable electrochemical cell
Dane Badawcze
- M. Cieśluk
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains STL files required for fabrication of an all 3D printed electrochemical cell, that can be used in electroanalytical studies.
Mechanical durability and electroanalytical performance of 3D-printed multi-material sensors
Dane Badawcze
- M. Cieślik
- M. Rucka
- A. Koterwa
- M. Rycewicz
- R. Bogdanowicz
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The data set consists tensile strength, electric resistance, electrochemical characteristics and physicochemical studies of multi-material 3D printed systems, including their sensing performance during detection of antibiotics in an industrial sewage. Additionally, contact angle measurements and SEM micrographs of the electrode surfaces were included.
Broadband dielectric spectroscopy studies of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains broadband dielectric spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
Thermal analyses of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- A. Rodak
- A. Susik
- M. Cieślik
- J. Ryl
- K. Formela
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains thermal analyses (TGA, DTG, DSC) studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different...
Topography studies of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains topography studies with scanning electron microscope of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material...
Rheology studies of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- A. Rodak
- A. Susik
- J. Ryl
- K. Formela
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains MFR/MVR (melt flow rate) rheology studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The study aims to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
Electrochemical analyses of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains cyclic voltammetry studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
Topography studies of screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains topography examination of SPCE containing boron-doped diamond BDD foils done with scanning electron microscope. Different points mark different electrode spots: A) working electrode, B) reference electrode, C) counter electrode, D) pads.
Physicochemical studies (Raman) of multiple times processed poly(lactic acid)-carbon black composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains Raman spectroscopy studies of commercially available ProtoPasta 3D printable filament, composed of poly-lactic acid (PLA) and conductive carbon black (CB) filler. The aim of the study is to observe structural differences and applied properties changes under multiple reprocessing of the composite material at different temperatures...
Electrochemical studies for screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains electrochemical examination of SPCE paste and SPCE containing boron-doped diamond BDD foils. The studies include kinetics analyses with cyclic voltammetry and electrochemical impedance spectroscopy with different redox probes: hexacyanoferrate(III) and Hexaammineruthenium(III) and potentiostatic open circuit potential at different...
Performance of Haemophilus influenzae impedimetric biosensors based on screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains electrochemical impedance spectroscopy studies of SPCE electrodes containing boron-doped diamond BDD foils and functionalized towards detection of Protein D and Haemophilus influenzae.
Chemical and structural studies of screen-printed carbon electrodes (SPCE) with boron-doped diamond foils
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains chemical analyses and structural studies by XPS and Raman spectroscopy, carried out for SPCE containing boron-doped diamond BDD foils done with scanning electron microscope. Different points for XPS analysis mark different electrode spots: A) working electrode, B) reference electrode, C) counter electrode, D) pads.
Physicochemical studies (Raman, XRD) of poly(lactic acid)-carbon black-nanodiamond composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains physico-chemical examination of a new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques include Raman spectroscopy and X-ray diffraction...
Physicochemical studies (BET) of nanoparticles used for 3D printable conductive composites
Dane Badawcze
- J. Ryl
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains physico-chemical examination of fillers used to fabricate new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Geometric surface area of the nanoparticles was studied by Brunauer–Emmett–Teller (BET) adsorption/desorption isotherms. Investigated samples: CB Ensaco 250G, detonation...
Electrochemical studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane Badawcze
- J. Ryl
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains electrochemical investigation on electrodes 3D printed using a new composite composed of poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The presented results contain:1. electrochemical characterisation...
Mechanical studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains mechanical tests carried out on new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques was dynamic mechanical analysis (DMA). The measurements...
Rheology studies of poly(lactic acid)-carbon black-nanodiamond composites
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains rheology measurements carried out on new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques was performed by melt mass-flow rates (MFR)....
Thermal stability analysis of poly(lactic acid)-carbon black-nanodiamond composite
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains thermal stability tests carried out on new 3D printing-dedicated composites with poly-lactic acid (PLA), carbon black (CB) and nanodiamond fillers. Two types of nanodiamonds were studied: detonation nanodiamonds (DND) and boron-doped carbon nanowalls (BCNW). The investigated techniques include: thermogravimetric analysis (TGA)...
New 3D printable filaments with nanodiamonds, physicochemical additives characteristics and electrochemical activity
Dane Badawcze
- M. Cieślik
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains the physicochemical analyses (XRD, Raman spectroscopy, BET analyses) and electrochemical analyses (CV, EIS) for a new 3D-printable composite has been developed dedicated to electroanalytical applications. Two types of diamondised nanocarbons - detonation nanodiamonds (DNDs) and boron-doped carbon nanowalls (BCNWs) - were added...
Raman spectroscopy analysis of poly(lactic acid)-carbon black composite treated by femtosecond laser
Dane Badawcze
- M. Cieślik
- M. Sawczak
- R. Jendrzejewski
- J. Celej
- W. Nogala
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the Raman spectroscopy measurements of commercially available carbon black-filled poly(lactic acid) 3D printed electrodes after femtosecond laser ablation. These results were utilized in the manuscript published in Electrochimica Acta: 10.1016/j.electacta.2022.140288
Partial PLA composite surface activation by femtosecond laser ablation
Dane Badawcze
- J. Ryl
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation, etching a certain % of the electrochemically-exposed electrode size. The % value is in the name of each file. The goal...
Scanning electrochemical micrographs of poly(lactic acid) 3D printed electrodes ablated by femtosecond laser
Dane Badawcze
- M. Cieślik
- M. Sawczak
- R. Jendrzejewski
- J. Celej
- W. Nogala
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the scanning electrochemical micrographs of the femtosecond laser (FSL) ablation at the surface of commercially available carbon black-filled poly(lactic acid) 3D printed electrode. The process is used for the increase of the charge transfer of this electrode in electrochemical studies.
Images revealing the effect of local femtosecond laser ablation of conductive poly(lactic acid) 3D printed electrodes
Dane Badawcze
- M. Cieślik
- M. Sawczak
- R. Jendrzejewski
- J. Celej
- W. Nogala
- J. Ryl
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset reveals the images of the femtosecond laser (FSL) ablation at the surface of commercially available carbon black-filled poly(lactic acid) 3D printed electrode. The process is used for the increase of the charge transfer of this electrode in electrochemical studies.
Partial PLA composite surface activation by femtosecond laser ablation
Dane Badawcze
- J. Ryl
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation operating with different parameters. These were: gas atmosphere (He or air, data in different subfolders), the percentage...
The topography of carbon black-polylactide composite 3D printed electrodes after femtosecond laser ablation
Dane Badawcze
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
This dataset contains a series of scanning electron microscopy images revealing the topography of 3D printed carbon black-polylactide composite electrodes after laser ablation with a femtosecond laser. Different laser powers were investigated, namely: 10%, 25%, 50%, 75% and 100%. The CB-PLA electrodes were 3D printed using an Ender printer. Femtosecond laser NKT Photonics, Origami XP parameters: power at 100%...
Caffeine detection using CB-PLA electrode after Nd:YAG laser ablation in He atmosphere
Dane Badawcze
- J. Ryl
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- I. Kaczmarzyk
- M. Głowacki
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains electrochemical studies in form of cyclic voltammetry (CV) and differential pulse voltammetry (DPV) of laser-activated 3D printed CB-PLA electrodes. The ablation of the 3D-printed CB-PLA electrodes was carried out using a pulsed LaserBlast 500 Nd:YAG laser (Quantel, France) operating at 1064 nm and a 6 ns pulse duration.
The XPS studies of the CB-PLA electrodes after different surface treatments (chemical, electrochemical, enzymatic)
Dane Badawcze
- J. Ryl
- I. Kaczmarzyk
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- S. Mania
- R. Tylingo
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the Xray Photoelectron Spectroscopy results of the studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by hydrolysis in different solvents (DMF, 1M HCl, 1M NaOH), electrolysis in 1M NaOH, enzymatic treatment in polymerase or simultaneous electrolysis...
Surface activation by cyclic polarization in 1M HCl and its effects on the electrochemical response of CB-PLA 3D printed electrodes
Dane Badawcze
- A. Koterwa
- J. Ryl
- I. Kaczmarzyk
- P. Niedziałkowski
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the electrochemical studies performed for surface activation of the CB-PLA 3D printed electrodes by electrolysis in 1M HCl solution. The studies were performed after treatment at different polarization ranges, as labeled in subfolder names. For each electrode the consecutive studies describe different samples, as labeled in subfolders:...
The cyclic voltammetry studies of CB-PLA electrode after surface activation by electrolysis in 1M NaOH
Dane Badawcze
- I. Kaczmarzyk
- J. Ryl
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the electrochemical studies performed for surface activation of the CB-PLA 3D printed electrodes by electrolysis in 1M NaOH solution. The studies were performed after treatment at an anodic overpotential of 1V, found to be optimal for surface activation. The measurements were carried out with cyclic voltammetry (CV) under different...
The electrochemical studies of CB-PLA electrode after surface activation by proteinase K digestion
Dane Badawcze
- J. Ryl
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- I. Kaczmarzyk
- S. Mania
- R. Tylingo
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the electrochemical studies performed to evaluate surface activation of the CB-PLA 3D printed electrodes by enzymatic hydrolysis in a solution containing proteinase K (72h digestion period). Different enzyme concentrations were evaluated: 0.2, 0.4, 0.6 and 0.8 mg/ml. The studies were performed before surface activation, during and...
The electrochemical studies of CB-PLA surface activation by electrolysis in 1M NaOH
Dane Badawcze
- I. Kaczmarzyk
- J. Ryl
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the electrochemical studies performed under different conditions of surface activation of the CB-PLA 3D printed electrodes. The activation was performed by electrolysis in 1M NaOH solution under cycling polarization with different anodic or cathodic overpotentials (data in different subfolders). The file names contain the exact...
The electrochemical studies of CB-PLA electrode after surface activation by proteinase K digestion with different times and concentrations
Dane Badawcze
- J. Ryl
- A. Koterwa
- P. Niedziałkowski
- M. Cieślik
- I. Kaczmarzyk
- S. Mania
- R. Tylingo
- seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites
The dataset contains the electrochemical studies performed to evaluate surface activation of the CB-PLA 3D printed electrodes by enzymatic hydrolysis in a solution containing proteinase K. DIfferent proteinase K concentrations and digestion times were evaluated, as described in subfolder names. The studies were performed before surface activation, during...

seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system liczba: 12

rozwiń zwiń

Interaction of PDA monomers with Au
Dane Badawcze
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains supplementary information in the form of Electrostatic difference potential (EDP) map, density of states (DOS) spectra, and adsorption geometries of polydopamine PDA monomers on the Au surface. PDA was modelled either as the oxidised (indolequinone, IQ) and reduced (dihydroxyindole, DHI) chemistries.
Supramolecular junctions of the PDA tetramers
Dane Badawcze
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
In this dataset, a set of polydopamine (PDA) supramolecular junctions with linear and cyclic tetramers in different oxidation states (indolequinone , IQ or dihydroxyindole, DHI) in the scattering region are investigated. Electronic structure of the supramolecular junction with cyclic and linear PDA tetramers, including Electron density maps for the...
Interactions of PDA tetramers with the Au surfaces
Dane Badawcze
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains electrostatic difference potential (EDP) maps, density of states (DOS) spectra, and adsorption geometries of cyclic tetramers on the Au surface. The real polydopamine was modelled either as the cyclic tetramers in the oxidised (indolequinone, IQ) and reduced (dihydroxyindole, DHI) chemistries with all units being the same - either...
Scanning Electron Microscopy images of nanocubes suspension 1 month after synthesis
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- A. Koterwa
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains the SEM images of the gold nanocubes suspension in citrate buffer. The goal of the study was to evaluate the size of the synthesized nanocubes, their stability one month after the synthesis process, and to verify the optimal conditions regarding nanocubes concentration for the SEM analysis. Solutions with two different AuNC concentrations...
Gold nanocubic structures functionalization with organic layers
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains the XPS spectra obtained for gold nanocubes (AuNC), which were deposited at the gold electrode surface and dried. The AuNC's were first functionalized with either cysteamine in EtOH or mercaptopropionic acid in EtOH. The concentration of these compounds was 20 mM. The interaction of the functionalized with the AuNC surface was...
Gold nanocubic structures agglomeration when put on conductive surfaces
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- A. Koterwa
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains Dynamic EIS results obtained for the gold electrodes with non-functionalized gold nanocubes (AuNC) deposited at its surface. The deposition was the following: 2 uL of the solvent containing CTAB as the surfactant was put on the electrode and dried, the same procedure was applied 5 times. Afterward, the electrode was immersed in...
Gold nanocubic structures agglomeration when put on conductive surfaces
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains SEM images of gold nanocubes (AuNC), which were deposited at the conductive Si wafer surface and dried. The deposition method, the solvent used and AuNC concentration have a significant influence on the homogeneous distribution and their agglomeration at the surface, further influencing the electrochemical characteristics of the...
Gold nanocubic structures agglomeration when put on conductive surfaces
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains SEM images of gold nanocubes (AuNC), which were deposited at the conductive Si wafer surface and dried. The deposition method, the solvent used and AuNC concentration have a significant influence on the homogeneous distribution and their agglomeration at the surface, further influencing the electrochemical characteristics of the...
Gold nanocubic structures agglomeration when put on conductive surfaces
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains SEM images of gold nanocubes (AuNC), which were deposited at the conductive Si wafer surface and dried. The deposition method, the solvent used and AuNC concentration have a significant influence on the homogeneous distribution and their agglomeration at the surface, further influencing the electrochemical characteristics of the...
Gold nanocubic structures agglomeration when put on conductive surfaces
Dane Badawcze
- J. Ryl
- P. Niedziałkowski
- A. Koterwa
- seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
This dataset contains Dynamic EIS results obtained for the gold electrodes with non-functionalized gold nanocubes (AuNC) deposited at its surface. The deposition was the following: 2 uL of the solvent containing CTAB as the surfactant was put on the electrode and dried, the same procedure was applied 5 times. Afterward, the electrode was immersed in...
Au nanoparticles identifiction with the use of AFM Volta potential mapping
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data , Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
The specific physical, chemical and electrochemical electrical properties of gold nanoparticles have led to their extensive use as high-performance chemical and biochemical sensors. The described properties relate to surface plasmon resonance, fluorescence quenching or enhancement, high electrical conductivity and light scattering. The described nanoparticles...
The AFM micrographs of gold nanoparticles on silicon substrate
Dane Badawcze
- seria: Scanning Probe Microscopies data , Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
The dataset contains the first approach towards AFM topographic imaging of gold nanoparticles synthesized and immobilized on the silicon surface. Measurements were made in the semi-contact mode on the NTEGRA Prima device, manufactured by NT-MDT. Scans were performed with amplitude detection at an operating value of 60% of the free oscillation amplitude....

seria: Scanning Probe Microscopies data liczba: 49

rozwiń zwiń

Silicon microcantilever with impedance sensor
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The issue of microelectromechanical systems (MEMS) [1] has been enjoying popularity and interest since the 90s of the 20th century. Microcells are one of the simplest devices of this type, but they can be widely used in sensors. There are reports on the possibility of using this type of sensors in the context of such important issues as diagnostics...
Destruction of AFM probes during normal operation
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The quality of the images obtained with the use of an atomic force microscope is determined by the state of the blade interacting with the tested material. Image artifacts can be generated by various reasons, such as oxidation, contamination or an error in blade fabrication, but also appear as a result of the repeated scanning process and inevitable...
Force-deformation spectroscopy in contact mode
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The deformation-distance spectroscopic curve is obtained by registering the value of the probe cantilever deflection as a function of the elongation of the piezoelectric scanner. It assumes a simple relationship in the form of Hooke’s law, linking the deformation of the lever with the amount of its deflection caused by the proximity of the probe and...
Imaging of biological samples: the ant Lasius Niger
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The world of arthropods continues to amaze researchers today. An example may be a relatively new report by a group of scientists on structures found in ant shells [1] Although calcareous anatomical structures have evolved in various groups of animals, little has been known so far about the occurrence of this type of form in insects. The authors of the...
Fingerprint structure studies with semi-contact AFM
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The work [1] presents many, sometimes even surprising examples of the use of atomic force microscopy in modern forensics. Some of them are projectile tests using the characteristic scratch patterns created by the firing pin on the primer. There are more and more suggestions in the literature for the use of atomic force microscopy in dactyloscopy [2]....
Imaging of biological samples: crassula arborescens
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
One of the tasks of modern botany is to describe the relationship between climatic conditions and other environmental factors and the anatomical structure and adaptation of species present in given geographic areas. The work [1] focuses on anatomical and morphological studies of leaves of plants from the coarse family. Species tested belong to leaf...
Visualization of the surface of the Nafion membrane
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Fuel cells use the chemical energy of hydrogen or other fuels to produce electricity. If the fuel is hydrogen, the only products are electricity, water and heat. Fuel cells are unique in the variety of their potential applications, they can use a wide variety of fuels. They are also highly scalable devices that can power both cars and mobile phones....
The surface of the sensor used in the analysis of odorous substances
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Human industrial activity usually leads to smaller or larger interference with the ecosystem, contributing to changes affecting the quality of life. An example may be the emission of gaseous substances, not necessarily toxic, but due to their intense smell, they can cause discomfort to people exposed to their inhalation. The problem is so important...
Statistics of AFM current-voltage curves
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Mapping surface electrical conductivity offers enormous cognitive possibilities regarding the structure and properties of modern materials. The technique invented for this purpose (Conductive AFM) by Murrel's team and colleagues allows independent monitoring of the local conductivity of materials in correlation with the topographic profile. The mentioned...
Amplitude-distance spectroscopy in semi-contact mode
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Since it was invented by Binnig et al. in 1986, atomic force microscopy (AFM) plays a key role in science and technology at the nanoscale. AFM is a microscopic technique that visualizes the surface topography using the attractive and repulsive forces of interaction between several atoms (in theory) of a blade attached to the end of the probe lever and...
The influence of external interference on AFM imaging, the use of a protective helmet
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
This collection is of purely practical importance, showing how the presence of external disturbances can adversely affect the quality of imaging with an atomic force microscope. For this reason, it is also advisable to provide a link to a workshop-like study [1] as well as a huge number of commercial solutions available after entering the keyword "AFM...
Microscopic examination of the texture of paper products
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Atomic force microscopy (AFM) can be used to study the state of the paper fibers with the aim of providing qualitative and semi-quantitative information on degradation and aging. The work [1] reports the results of tests of various paper products subjected to deliberate aging processes under the influence of various factors. Chemical and biological...
Austenitic stainless steel sensitization
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
High-alloy steels, thanks to their composition and content of appropriate alloying additives, are characterized by increased resistance to many corrosive environments. However, this is due to the increased sensitivity of the described construction materials to specific environmental conditions during their use. An example may be the increased susceptibility...
Imaging of ferroelectric properties of sinter by means of Piezoresponse Force Microscopy
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Ferroelectricity is a property of certain materials [1], characterized by a spontaneous electrical polarization that can be reversed by applying an external electric field. Ferroelectric properties can be used to make capacitors with adjustable capacity. The permeability of ferroelectrics is not only regulated, but usually also very high, especially...
Colvolutional calibration of AFM probe
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Atomic force microscopy is based on the interaction of the examined surface with a probe of a pyramidal shape, tipped with a sharp end with a radius of curvature ranging from single nanometers to hundreds of nanometers. The resolution of the obtained image is of course dependent on the above-mentioned geometric size, and the resulting image is a convolutional...
Ferromagnetic nanoparticles imaging by means of Magnetic Force Microscopy
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Ferromagnetic nanoparticles can be used as building blocks for advanced thin film magnets, and can also be used in data storage and biomedical technologies. Nano-crystalline ferrites with the chemical formula NixZn (1 - x) Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0 show anti-corrosion properties and suppress electromagnetic interference, in the case...
AFM and SSRM investiagtion of carbon nanowalls properties
Dane Badawcze
- seria: Scanning Probe Microscopies data
Structures with limited dimensionality are of great interest in modern nanotechnology. The properties of these objects are used, among others, for the construction of modern displays or as a base for quantum computers. Carbon nanowalls, which are the subject of the imaging results contained in this collection, are also considered interesting building...
Imaging of the effects of pitting corrosion with the use of AFM
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Pitting corrosion is a local attack on a metal surface, limited to a point or small area, which appears as a hole. Pitting corrosion is one of the most harmful forms of corrosion due to the fact that it is associated with small, difficult to detect damage, that can even lead to perforation of the structure. A single pit may range in size from micrometers...
Identification of intermetallic phases in the structure of austenitic steel with use of Scanning Kelvin Probe Microscopy
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Delta ferrite is formed in austenitic steels during the solidification of the alloy and its welds. It can also occur as a stable phase in any temperature range in high-alloy austenitic-ferritic steels. Depending on the amount, it can change into gamma and sigma phases and into ferrite with variable chromium content. The main role of delta ferrite in...
Nanostructures fabrication with use of electrical AFM litography
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
In the last 10 years, one of the nanotechnological trends has been observed, consisting in the development of new variants of computer memory systems with high capacity and speed of access, using quantum dots. One of the techniques for creating nanodots and other nanostructures is based on the use of an atomic force microscope acting as a lithographic...
Detection of the acoustic interferences during AFM operation
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Atomic force microscopy is a particularly complicated surface imaging technique due to the large number of factors that affect the quality of the resulting images. They are obviously difficult and sometimes even impossible to control at the same time. One of such factors may even be the seismological location of the building or the influence of mechanical...
Imaging and chemical investigation of silver coating
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The recovery of silver from materials such as plates, still used in clinical radiography [1], or scrap jewelery is still very popular. The subject of the research, part of which was microscopic imaging, was to recreate the behavior of an electrochemically deposited silver coating. The copper electrodes were covered with a layer of silver obtained from...
Imaging of morphological and physicochemical changes occuring in the structure of austenitic steel due to the thermal sensitization
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
In polycrystalline materials, grain boundaries are always where phenomena such as surface diffusion, sedimentation and corrosion occur. They have a significant impact on the macroscopic properties of the construction material [1]. In addition to inhomogeneities such as manganese sulphide inclusions formed during the metallurgical process, interfacial...
Exemplary AFM application in cosmetology
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Atomic force microscopy can be used in the diagnosis of the condition of human tissues such as skin, nails and hair. This is obviously related to the use of a variety of cosmetic products and can be understood as an attempt to assess their long-term impact on human appearance and health. An example may be the studies presented in [1] indicating the...
AFM investigation of electrode fabricated by 3D printing
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
3D printing, also known as additive manufacturing, has enjoyed great interest in recent years due to the versatility of this method of producing various shapes and details. Due to the possibility of precise control of the shape and composition of the printed elements, the discussed technique can be widely used in electrochemistry, including electrochemical...
AFM visualization of Mg alloy surface modification
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Magnesium alloys with additives improving their mechanical properties are valued as materials with low density and elasticity coefficient. Additionally, their biocompatibility and biodegradability make them interesting in prosthetic applications. However, the last of these features, valuable in medicine, contradicts the industrial needs for the described...
Au nanoparticles identifiction with the use of AFM Volta potential mapping
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data , Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
The specific physical, chemical and electrochemical electrical properties of gold nanoparticles have led to their extensive use as high-performance chemical and biochemical sensors. The described properties relate to surface plasmon resonance, fluorescence quenching or enhancement, high electrical conductivity and light scattering. The described nanoparticles...
AFM analysis of duplex steel structure and composition
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Due to the high content of alloying elements, duplex stainless steels are characterized by a complex structure of phase transitions. Among all types of intermetallic compounds, the sigma phase is of major interest due to its detrimental effect on both mechanical properties and corrosion behavior. It is an intermetallic phase enriched in Cr and Mo and...
Validation of result of STM probe fabrication
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The scanning tunneling microscope [1] is a powerful research tool that allows, among other things, to obtain images with atomic resolution. A serious limitation of the described microscope is its limited applicability relating to conductive and semiconductor materials and the reproducibility of measurements depending on the preparation of the measuring...
Examples of AFM applications in liquid environment
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Important advantage of atomic force microscopy (also tunneling microscopy) is the ability to work in different environments (vacuum, controlled atmosphere, liquid environment). The last one, open interesting possibilities, such as imaging of delicate biological materials in their natural state. The use of electrochemical mode allows for the modification...
Imaging of graphene surface by means of tapping mode AFM
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Graphene [1] is a material consisting of carbon planes with a hexagonal structure. One of the facts of interest from a purely scientific point of view is the very high mobility of electrons in the described material, allowing the study of relativistic effects inside a solid sample. Other features, such as bactericidal activity, make graphene an interesting...
AFM imaging of surface of modern soldering alloy
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Following the announcement in 2006 of European Union directives aimed at limiting the use of lead in electronic products, there was an urgent need to use lead-free solders in the electronics industry. Due to production requirements, it is necessary to use solders with different melting points. To replace the low-melting eutectic Sn 37 wt. Pb, the most...
Morphology and conductivity investigations of nickel-molybdenium alloy by means of Scanning Spreading Resistance Microscopy
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Electrolytically deposited nickel-molybdenum alloys are interesting materials because of their high corrosion resistance and low over-potential for hydrogen evolution. Despite many studies devoted to the deposition of these alloys, the mechanism of co-deposition is not fully understood [1]. The aim of the research was to preserve the electrochemically...
AFM images of the platinum (111) single crystal surface as delivered, without the polishing treatment
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Platinum (111) single crystal surface images as delivered, without polishing treatment. Topographic measurements in contact mode. NTEGRA Prima (NT-MDT) device. CSG probe 10.
Images of topography and mechanical properties (phase imaging) of cast iron samples from water installations
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Measurements in contact and semi-contact mode. NTEGRA Prima (NT-MDT) device. CSG 10.
Results of calibration of the piezoelectric scanner using the probe TGQ1
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Teaching file. Results of calibration of the piezoelectric scanner using the probe TGQ1. Scanning in contact mode. NTEGRA Prima (NT-MDT) device. CSG probe 10.
The surface of a fragment of the structure of an integrated circuit in the semi-contact mode.
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The surface of a fragment of the structure of an integrated circuit. Topographic measurements in the semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
Atomic force microscopy images of copper electrical contacts wear under the influence of friction
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Measurement of wear of copper electrical contacts under the influence of friction. Imaging in contact mode in the variant of scanning spreading resistance microscopy. Additionally, there are spectroscopic current-voltage curves showing local changes in electrical conductivity. NTEGRA Prima (NT-MDT) device. Probe NSG 01Pt.
Topographic AFM imaging of the leaf surface with magnification of details of its morphological structure
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Topographic imaging of the leaf surface with magnification of details of its morphological structure. Measurements in semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
The AFM topographic measurements of the surface heterogeneity of iron hexacyanoferrate on a steel surface
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Measurements in semi-contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
Mechanical lithography in a polymer substrate using AFM in contact mode
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
Mechanical lithography in a polymer substrate. Contact mode. NTEGRA Prima (NT-MDT) device. NSG 01 probe.
Integrated circuit structure surface images obtained with contact capacitive imaging technique
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The measurements were done using NTEGRA Prima (NT-MDT) device. CSG 10Pt probe.
The AFM micrographs of gold nanoparticles on silicon substrate
Dane Badawcze
- seria: Scanning Probe Microscopies data , Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system
The dataset contains the first approach towards AFM topographic imaging of gold nanoparticles synthesized and immobilized on the silicon surface. Measurements were made in the semi-contact mode on the NTEGRA Prima device, manufactured by NT-MDT. Scans were performed with amplitude detection at an operating value of 60% of the free oscillation amplitude....
The scanning spreading resistance microscopy (SSRM) studies of heavy boron-doped diamond oxidation under high-temperature
Dane Badawcze
- seria: Scanning Probe Microscopies data
The dataset contains the results of scanning spreading resistance microscopy (SSRM) of heavy boron-doped diamond (BDD) electrodes subjected to high-temperature oxidation in a furnace at 600 Celsius. The micrographs reveal the local change of electric properties at certainly crystallographic orientations of BDD grains and at the grain boundaries due...
The AFM micrographs of pitting corrosion evolution on high-alloy steel 1.4301
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The dataset contains the results of topographic imaging of high-alloy stainless steel 1.4301 on which the pitting corrosion process was induced by electrochemical methods. The study of the effects of a local attack allows for conclusions about the intensity and mechanism of this type of corrosion. The file contains atomic force microscopy (AFM) data...
The scanning spreading resistance microscopy (SSRM) of some CoCrMo alloys subjected to electrochemical litography
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The dataset contains the results of the experiment consisting of performing electrochemical lithography on the surface of the CoCrMo prosthetic alloy. First, by applying local anodic polarization, oxide structures were created on the surface of the material. Next, they were imaged in the SSRM (scanning spreading resistance microscopy) mode to visualize...
The exemplary Kelvin probe microscopy studies of sensitized austenitic stainless steels
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The dataset summarizes the results of imaging the surface potential distribution using the Kelvin probe scanning technique. Due to the fact that the potential measured in this way is proportional to the electrochemical potential of metals or intermetallic phases, it is possible to assess the nobility differences of various alloy components. In the case...
The AFM micrographs of austenitic stainless steel subjected to sensitization for intergranular corrosion
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The dataset contains atomic force microscopy (AFM) maps of topographic images of austenitic steel samples subjected to sensitization to the process of intergranular corrosion. Precipitations of carbides as well as other intermetallic phases can be observed and detected before the fragments of structures sensitized by improper thermal treatment are exposed...
The scanning tunnelling micrographs of highly oriented pyrolytic graphite
Dane Badawcze
- A. Zieliński
- J. Ryl
- seria: Scanning Probe Microscopies data
The dataset contains the results imaging of a sample of highly oriented pyrolytic graphite obtained using scanning tunneling microscopy. The above variant of scanning probe microscopy is one of the most convenient research techniques at atomic scales. The file contains images corresponding to increasing magnifications from the 1 um scale to a few nanometers....

seria: TeO2-based materials liczba: 20

rozwiń zwiń

Luminescence properties of TeOx-1%Eu1.5%Tb2.5%Dy thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-1%Eu1.5%Tb2.5%Dy thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of rare-earth ions were added, the nitrates were used as a source of rare-earth...
Luminescence properties of TeOx-2%Eu1.5%Tb1.5%Dy thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-2%Eu1.5%Tb1.5%Dy thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of rare-earth ions were added, the nitrates were used as a source of rare-earth...
Luminescence properties of TeOx-2%Eu1.5%Tb1.5%Tm thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-2%Eu1.5%Tb1.5%Tm thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of rare-earth ions were added, the nitrates were used as a source of rare-earth...
Luminescence properties of TeOx-Dy thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Dy thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of dysprosium ions were added, the nitrates were used as a source of rare-earth ions....
Luminescence properties of TeOx-Dy thin films
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Dy thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of dysprosium ions were added, the nitrates were used as a source of rare-earth ions....
Luminescence properties of TeOx-Eu thin films
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Eu thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of europium ions were added, the nitrates were used as a source of rare-earth ions. The...
Luminescence properties of TeOx-Eu thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Eu thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of europium ions were added, the nitrates were used as a source of rare-earth ions. The...
Luminescence properties of TeOx thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. The sol was obtained by vigorously stirring precursor solution at 50°C for 2h, then the temperature was raised...
Luminescence properties of TeOx-Tb thin films annealing under an oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Tb thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of terbium ions were added, the nitrates were used as a source of rare-earth ions. The...
Luminescence properties of TeOx-Tb thin films
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Tb thin films. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of terbium ions were added, the nitrates were used as a source of rare-earth ions. The...
Luminescence properties of TeOx gels
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx gels. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. The sol was obtained by vigorously stirring precursor solution at 50°C for 2h, then the temperature was raised...
Luminescence properties of TeOx-Tb gels
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Tb gel. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of terbium ions were added, the nitrates were used as a source of rare-earth ions. The sol was...
Luminescence properties of TeOx-Dy gels
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Dy gel. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of dysprosium ions were added, the nitrates were used as a source of rare-earth ions. The sol...
Luminescence properties of TeOx-Eu gels
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the emission and excitation spectra of TeOx-Eu gels. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of europium ions were added, the nitrates were used as a source of rare-earth ions. The sol...
XRD patterns of TeOx powder
Dane Badawcze
- seria: TeO2-based materials
The DataSet contains the XRD patterns of the TeOx powder. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. The sol was obtained by vigorously stirring precursor solution at 50°C for 2h, then the temperature was raised to 75°C for the...
Thermal behavior of TeOx powder
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the results of the thermal behavior of the TeOx powder. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. The sol was obtained by vigorously stirring precursor solution at 50°C for 2h, then the temperature was raised...
XRD patterns of TeOx-BaO-BiO powder
Dane Badawcze
- seria: TeO2-based materials
The DataSet contains the XRD patterns of the TeOx-BaO-BiO powder. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor), barium carbonate, and bismuth carbonate with thetraetylene glycol, water, ethanol, and acetic acid. (Samples molar concentration: 73TeO2-4BaO-3Bi2O3 and 73TeO2-3BaO-4Bi2O3)....
Optical properties of TeOx gels doped with a mix of rare-earth ions
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the UV-Vis spectra of the TeOx gels doped with a mix of rare-earth ions. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the different molar concentration of rare-earth ions was added, nitrates were used...
Optical properties TeOx gels doped with the rare-earth ions
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the UV-Vis spectra of TeOx gels doped with the rare-earth ions. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. Next, the 5% mol of the rare-earth ions were added, the nitrates were used as a source of rare-earth...
Thermal behavior of TeOx xerogel powder under different atmospheres
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: TeO2-based materials
The DataSet contains the results of the thermal behavior of the TeOx xerogel powder measured under different atmospheres. The material was obtained by the sol-gel method. The starting solution was prepared by mixing telluric acid (precursor) with thetraetylene glycol, water, and ethanol. The sol was obtained by vigorously stirring precursor solution...

seria: Ammonium vanadate liczba: 19

rozwiń zwiń

Thermal behavior of (NH4)V4O10xH2O
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the (NH4)V4O10xH2O obtained by the hydrothermal method using different precursors: microstructured (commercially available) or nanostructured. The information about samples synthesis is described in the Materials.
SEM micrographs of ammonium vanadate nanocrystals
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the electron microscopy (SEM) micrographs of ammonium vanadate nanobelts obtained by the hydrothermal method with different conditions. The results show that the morphology of samples dependent on reaction conditions.
X-ray Photoelectron Spectroscopy studies of ammonium vanadate
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the high-resolution XPS studies of the ammonium vanadate nanostructures obtained by the hydrothermal method. XPS analyses were carried out with an X-ray photoelectron spectrometer (Omicron NanoTechnology) with a 128-channel collector. The measurements were performed at room temperature in an ultra-high vacuum condition (below 1.1x10-8...
SEM micrographs of NH4VO3 crystals - molar concetration factor after annealing
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the scanning electron microscopy (SEM) micrographs of NH4VO3 nano_crystals obtained by the LPE-IonEx method with different morphology after annealing at 400C under argon atmosphere (with a heating rate of 10 C/min).
Rate performance of (NH4)2V10O25·8H2O as cathode material in Li-ion batteries
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the galvanostatic charge/discharge curves of the ammonium vanadate nanostructures obtained by the hydrothermal method under an initial pressure of 50 bar ((NH4)2V10O25·8H2O). The battery tests of the samples were performed using the ATLAS 0961 MBI multichannel battery testing system with different current densities in the voltage...
Rate performance of mixture (NH4)2V6O16 and (NH4)2V10O25·8H2O as cathode material in Li-ion batteries
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the galvanostatic charge/discharge curves of the ammonium vanadate nanostructures obtained by the hydrothermal method without initial pressure (mixture (NH4)2V6O16 and (NH4)2V10O25·8H2O). The battery tests of the samples were performed using the ATLAS 0961 MBI multichannel battery testing system with different current densities...
DSC measurments of ammonium vanadate nanocrystals
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the thermal behavior of the ammonium vanadate nanostructures obtained by the hydrothermal method with different conditions. Differential scanning calorimetry (DSC) measurement was carried out under an argon atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The results reveal the differences...
Thermal behaviour of ammonium vanadate nanocrystals
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the thermal behavior of the ammonium vanadate nanostructures obtained by the hydrothermal method with different conditions. Thermogravimetric analysis (TG) was carried out under an argon atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also studied with mass spectrum...
SEM micrographs of NH4VO3 crystals
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the scanning electron microscopy (SEM) micrographs of NH4VO3 crystals obtained by the LPE-IonEx method. The SEM images clearly show that the morphology of the end product can be nicely tuned by changing the type of ammonium salt and the solvent. It can be concluded that the used solvent affected crystal shapes and their size was...
Thermal behaviour of NH4VO3 elongated microcrystals
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the ammonium metavanadate elongated microcrystals under argon and nitrogen atmosphere. Thermogravimetric analysis (TG) was carried out under argon or nitrogen atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also studied with mass...
Thermal behaviour of NH4VO3 microcasketoids
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the ammonium metavanadate microcasketoids under argon and nitrogen atmosphere. Thermogravimetric analysis (TG) was carried out under argon or nitrogen atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also studied with mass spectrum...
Thermal behaviour of NH4VO3 microflowers
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the ammonium metavanadate microflowers under argon and nitrogen atmosphere. Thermogravimetric analysis (TG) was carried out under argon or nitrogen atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also studied with mass spectrum...
Thermal behaviour of NH4VO3 nanoflowers
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the ammonium metavanadate nanoflowers under argon and nitrogen atmosphere. Thermogravimetric analysis (TG) was carried out under argon or nitrogen atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also studied with mass spectrum...
Structure of ammonium vanadate synthesis by LPE-IonEx method
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the XRD patterns, FTIR spectra of NH4VO3 crystals with different morphology obtained by the LPE-IonEx method.
Morphology and structure of ammonium vanadates synthesis by hydrothermal method
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the XRD patterns, FTIR spectra, and scanning electron microscopy (SEM) micrographs of ammonium vanadates synthesis by hydrothermal method from different NH4VO3 precursors. The results reveal that a mixture of (NH4)V4O10xH2O and(NH4)0.76V4O10 was obtained for both precursors, however the contribution of each phase was different for...
Thermal behaviour of commercial avaible NH4VO3
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the results of the thermal behavior of the commercially available ammonium metavanadate (CAS 7803-55-6) under argon and nitrogen atmosphere. Thermogravimetric analysis (TG) was carried out under argon or nitrogen atmosphere from 40C to 560C (with a heating rate of 10 C/min) using Netzsch STA 449 F1. The thermal behavior was also...
TEM micrographs of ammonium vanadate nanocrystals
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Ammonium vanadate
The DataSet contains the TEM images of ammonium vanadate nanobelts obtained by the hydrothermal method with different conditions. The results show that the microstructure of an ammonium vanadate single nanobelt dependent on reaction condition.
SEM micrographs of NH4VO3 crystals - molar concetration factor
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the scanning electron microscopy (SEM) micrographs of NH4VO3 nano_crystals obtained by the LPE-IonEx method. The SEM images clearly show that the morphology of the end product can be nicely tuned by changing the molar concentration of ammonium salt in the solvent.
XRD patterns of ammonium vanadate nanocrystals
Dane Badawcze
- seria: Ammonium vanadate
The DataSet contains the XRD patterns of ammonium vanadate nanobelts obtained by the hydrothermal method with different conditions. The results show that the structure and phase compositions of samples dependent on reaction conditions.

seria: Vanadium oxides liczba: 92

rozwiń zwiń

Thermal behavior of VO2/V2O3 nanostructures obtained at 1000°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 1000°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal properties of VO2 and V2O3 nanostructures
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the DSC and TG curves of VO2 and V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The xerogel powder was annealing under argon atmosphere at the selected temperature: 500C, 600C, and 1000C.
Thermal behavior of VO2/V2O3 nanostructures obtained at 650°C under reducing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 650°C under a reducing atmosphere (95% Ar 5% H2). The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behavior of VO2/V2O3 nanostructures obtained at 800°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 800°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behavior of VO2/V2O3 nanostructures obtained at 700°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 700°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behavior of VO2/V2O3 nanostructures obtained at 600°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 600°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behavior of VO2/V2O3 nanostructures obtained at 500°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 500°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behavior of VO2/V2O3 nanostructures obtained at 400°C under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the VO2/V2O3 nanostructures. The vanadium oxides nanostructures were synthesized by the sol-gel method, where obtained xerogel powder was annealing at 400°C under an argon atmosphere. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Linear impedance of V2O5 nanorods obtained at 893K
Dane Badawcze
- M. Prześniak-Welenc
- N. Wójcik
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
Linear impedance of V2O5 nanorods obtained at 903K
Dane Badawcze
- M. Prześniak-Welenc
- N. Wójcik
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
Linear impedance of V2O5 nanorods obtained at 913K
Dane Badawcze
- M. Prześniak-Welenc
- N. Wójcik
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
Linear impedance of V2O5 nanorods obtained at 923K
Dane Badawcze
- M. Prześniak-Welenc
- N. Wójcik
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
Non-linear impedance of V2O5 nanorods obtained at 923K
Dane Badawcze
- M. Prześniak-Welenc
- N. Wójcik
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the non-linear electrical properties of V2O5 nanorods which were measured by the impedance spectroscopy method. V2O5 nanorods were obtained by the sol-gel method. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The precursor powder was pressed into the disk-shaped pellets (12mm in diameter...
XRD patterns of VO2 and V2O3 thin films obtained at 500°C
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (3-9 AsP layers) were deposited on a silicon substrate and were annealing at 500°C under an argon atmosphere.
XRD patterns of VO2 and V2O3 thin films obtained at 700°C
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (5-9 AsP layers) were deposited on a silicon substrate and were annealing at 700°C under an argon atmosphere.
SEM micrographs of morphology evolution of VO2 and V2O3 thin films obtained at 1000°C dependent on film thickness
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (2-3 AsP layers) were deposited on a silicon substrate and were annealing at 1000°C under an argon...
SEM micrographs of morphology evolution of VO2 and V2O3 thin films obtained at 1000°C
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films were deposited on a silicon and quartz glass substrate and were annealing at 1000°C under an argon atmosphere.
SEM micrographs of morphology evolution of VO2 and V2O3 thin films obtained at 500°C
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (3-9 AsP layers) were deposited on a silicon substrate and were annealing at 500°C under an argon...
SEM micrographs of morphology evolution of VO2 and V2O3 thin films obtained at 700°C
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V2O3 thin films obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (3-9 AsP layers) were deposited on a silicon substrate and were annealing at 700°C under an argon...
Thermal behaviour of vanadium xerogel powder under different inert atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
FTIR spectra of VO2 and V2O3 nanostructures
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the FTIR spectra of VO2 and V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The xerogel powder was annealing under argon atmosphere in the temperature range 400-1000C. The results show that the morphology...
XRD patterns of VO2 and V2O3 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of VO2 and V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The xerogel powder was annealing under argon atmosphere in the temperature range 400-1000C. The results show that the morphology...
SEM micrographs of morphology evolution of VO2 and V2O3 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The information about xerogel powder synthesis is described in the Journal of Nanomaterials. The xerogel powder was annealing under argon atmosphere in the temperature range 400-800C. The...
Thermal behaviour of vanadium xerogel powder under argon atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behaviour of vanadium xerogel powder and V2O5 nanorods under helium atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the vanadium xerogel powder and V2O5 nanorods obtained at 650C. The information about xerogel powder and V2O5 nanorods synthesis is described in the Journal of Nanomaterials.
Changes in heat of vanadium xerogel powder under different atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the DSC curves of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal stability of vanadium xerogel powder under different atmpshere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal behaviour of vanadium xerogel powder under oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the results of the thermal behavior of the vanadium xerogel powder. The information about xerogel powder synthesis is described in the Journal of Nanomaterials.
Thermal stability of V2O5 nanorods under oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the TGA curves of V2O5 nanorods obtained at 650°C. The information about nanorods synthesis is described in the Journal of Nanomaterials.
Changes in heat flow of V2O5 nanorods under oxidizing atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the DSC curves of V2O5 nanorods obtained at 650°C. The information about nanorods synthesis is described in the Journal of Nanomaterials.
Changes in heat flow of V2O5 nanorods under inert atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the DSC curves of V2O5 nanorods obtained at 650°C. The information about nanorods synthesis is described in the Journal of Nanomaterials.
Thermal stability of V2O5 nanorods under inert atmosphere
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the TGA curves of V2O5 nanorods obtained at 650°C. The information about nanorods synthesis is described in the Journal of Nanomaterials.
Decomposition kinetics of vanadium xerogel powder
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the TGA curves of vanadium As-prepared xerogel powder with different heating rates. The information about sol synthesis is described in the Journal of Nanomaterials.
Crystallization kinetics of V2O5 nanorods
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the DSC curves of As-prepared xerogel powder with different heating rates. The information about sol synthesis is described in the Journal of Nanomaterials.
Chemical composition of V2O5 nanorods
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the chemical compositions of the V2O5 nanorods on a silicon substrate. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The As-prepared thin films were annealed at 600C under a synthetic air atmosphere.
XRD patterns of vanadium oxide nanostructures on silicon substrate obtained by V2O5 recrystallization
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of vanadium oxide nanostructures on silicon substrates obtained by recrystallization of V2O5 thin films between 800-1200°C under synthetic air. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials.
XRD patterns of vanadium oxide nanostructures on quartz glass substrate obtained by V2O5 recrystallization
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of vanadium oxide nanostructures on quartz glass substrates obtained by recrystallization of V2O5 thin films between 800-1200°C under synthetic air. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials.
SEM micrographs of vanadium oxide nanostructures obtained by V2O5 recrystallization at 1200°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of vanadium oxide nanostructures on quartz glass and silicon substrates obtained by recrystallization of V2O5 thin films at 1200°C under synthetic air. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials.
SEM micrographs of vanadium oxide nanostructures obtained by V2O5 recrystallization at 1000°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of vanadium oxide nanostructures on quartz glass and silicon substrates obtained by recrystallization of V2O5 thin films at 1000°C under synthetic air. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials.
SEM micrographs of vanadium oxide nanostructures obtained by V2O5 recrystallization at 800°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of vanadium oxide nanostructures on quartz glass and silicon substrates obtained by recrystallization of V2O5 thin films at 800°C under synthetic air. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials.
Structure evolution of V2O5 thin films deposited on quartz glass substrate - High-Temperature X-ray Diffraction
Dane Badawcze
- M. Prześniak-Welenc
- M. Gazda
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 thin films deposited on guartz glass. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on the quartz glass substrate. The structure was measured in-situ during heating between 50-800°C under synthetic...
Structure evolution of V2O5 thin films deposited on silicon substrate - High-Temperature X-ray Diffraction
Dane Badawcze
- M. Prześniak-Welenc
- M. Gazda
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 thin films deposited on silicon substrates (111). The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on the silicon substrate. The structure was measured in-situ during heating between 50-800°C under...
SEM micrographs of V2O5 thin films deposited on isotropic etching silicon substrates (111)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 thin films deposited on isotropic etching silicon substrates (111). The silicon wafers were etched in a mixture of nitric acid, hydrofluoric acid, and acetic acid in the ratio of 40:1:15. The soaking time for the substrates was from 30 to 90 seconds. The thin films were...
XRD patterns of V2O5 thin films deposited on isotropic etching silicon substrates (111)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 thin films deposited on isotropic etching silicon substrates (111). The silicon wafers were etched in a mixture of nitric acid, hydrofluoric acid, and acetic acid in the ratio of 40:1:15. The soaking time for the substrates was from 30 to 90 seconds. The thin films were obtained by the sol-gel method. ...
The AFM micrographs of V2O5 single crystals
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of V2O5 single crystals. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The As-prepared films were deposited on a quartz glass substrate and were annealing at 600°C under synthetic air.
The AFM micrographs of vanadium oxides thin films deposited on silicon - the influence of the thickness of the film on morphology
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (1, 2 or 3 AsP layers) were deposited on a silicon substrate and were annealing...
The AFM micrographs of vanadium oxides thin films deposited on quartz glass - the influence of the thickness of the thin film on its morphology
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The thin films with different thicknesses (1, 2 or 3 AsP layers) were deposited on a quartz glass substrate and were...
The AFM micrographs of vanadium oxides thin films obtained at 450°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxides thin films obtained at 400°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxides thin films obtained at 1200°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxides thin films obtained at 800°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on a silicon substrate and vanadium thin films were obtained by annealing as-prepared films at...
The AFM micrographs of vanadium oxides thin films obtained at 600°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of of vanadium oxides thin films obtained at 300°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxides thin films obtained at 200°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxides thin films obtained at 150°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
The AFM micrographs of vanadium oxide thin films obtained at 100°C
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of the surface of vanadium oxide thin films. The thin films were obtained by the sol-gel method. The information about sol synthesis is described in the Journal of Nanomaterials. The sol was deposited on quartz glass and silicon substrate and vanadium thin films were obtained by annealing as-prepared...
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-load
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum load of Berkovich indenter force from 2 to 50 mN.
Mechanical properties of single V2O5 nanocrystal - nanoindentation measurement in control of the max-depth
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the nanoindentation curves (indentation force Fn vs penetrationPd) for a single V2O5 nanocrystal supported on a substrate. The measurements were performed in control of the maximum depth of Berkovich indenter penetration: 60, 70, and 100 nm.
The AFM micrographs of isotropic etching silicon substrates (111)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the atomic force microscope images of isotropic etching silicon substrates (111). The silicon wafers were etched in a mixture of nitric acid, hydrofluoric acid, and acetic acid in the ratio of 40:1:15. The soaking time for the substrates was from 20 to 90 seconds
The morphology of V2O5 nanostructures deposited on quartz glass
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the confocal microscope images of morphology evolution of vanadium pentaoxide nanostructures on quartz glass obtained by annealing as-prepared films at 500C and 600C under synthetic air.
SEM micrographs of V2O5 nanocrystals as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 nanocrystals as cathode materials before and after the galvanostatic charge/discharge curves.
XRD patterns of V2O5 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of vanadium pentaoxide nanostructures obtained by the sol-gel with different annealing temperatures under synthetic air. The results show that crystallinity dependent on the annealing temperature.
SEM micrographs of V2O5 nanorods as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 nanorods as cathode materials before and after the galvanostatic charge/discharge curves.
SEM micrographs of morphology evolution of V2O5 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of morphology evolution of vanadium pentaoxide nanostructures obtained by the sol-gel, depending on annealing temperature under synthetic air. The results show that the morphology dependent on the annealing temperature.
FTIR spectra of V2O5 nanostructures
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains FTIR spectra of vanadium pentaoxide nanostructures obtained by the sol-gel with different annealing temperatures under synthetic air.
XRD patterns of V2O3 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The xerogel powder was annealing under a reducing atmosphere (94% Ar, 6% H2) in the temperature range 350-700C. The results show that crystallinity dependent on the annealing temperature.
SEM micrographs of morphology evolution of V2O3 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O3 nanostructures obtained by the sol-gel with different reaction conditions. The xerogel powder was annealing under a reducing atmosphere (94% Ar, 6% H2) in the temperature range 350-700C. The results show that the morphology dependent on the annealing temperature.
SEM micrographs of the V2O5 coatings after thermal treatment under reducing atmosphere
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 coatings on the silicon substrate after thermal treatment under a reducing atmosphere. Thin films were annealed at 600C and 700C for 10 under a reducing atmosphere (94% Ar, 6% H2).
XRD patterns of the V2O5 coatings after thermal treatment under reducing atmosphere
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 coatings on the silicon substrate after thermal treatment under a reducing atmosphere. Thin films were annealed at 500C, 600C, and 700C for 10 under a reducing atmosphere (94% Ar, 6% H2).
Morphology and structure of V2O5 nanorods deposited on the silicon substrate after reduction
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns and SEM micrographs of V2O5 nanorods on the silicon substrate after thermal treatment under a reducing atmosphere. Thin films were annealed at 500C for 40 under a reducing atmosphere (94% Ar, 6% H2).
XRD patterns of the V2O5 nanorods after thermal treatment under reducing atmosphere
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 nanorods after thermal treatment under a reducing atmosphere. Samples were annealed at 450C for 2, 20, and 40h under a reducing atmosphere (94% Ar, 6% H2).
SEM micrographs of the V2O5 nanorods after thermal treatment under reducing atmosphere
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the SEM micrographs of V2O5 nanorods after thermal treatment under a reducing atmosphere. Samples were annealed at 450C for 2, 20, and 40h under a reducing atmosphere (94% Ar, 6% H2).
SEM micrographs of VO2 and V6O13 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of VO2 and V6O13 thin films deposited on a silicon substrate. The as-prepared thin films were annealing under a reducing atmosphere (94% Ar, 6% H2) at 600 and 700C for 10h.
XRD patterns of VO2 and V6O13 nanostructures
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of VO2 and V6O13 thin films deposited on a silicon substrate. The as-prepared thin films were annealing under a reducing atmosphere (94% Ar, 6% H2) at 500, 600 and 700C for 10h.
SEM micrographs of morphology evolution of V2O5 thin films on silicon substrate
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 thin films deposited on a silicon substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range 250-600C. The results show that the morphology of the films dependent on the annealing temperature.
TEM micrographs of V2O5 nanostructures
Dane Badawcze
- M. Prześniak-Welenc
- J. Ryl
- seria: Vanadium oxides
The DataSet contains the TEM images of V2O5 nanostructures obtained by the sol-gel method.
Electrochemical impedance spectra and CV curves of V2O5 nanorods
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the EIS spectra for coin-cells and CV curves with the V2O5 nanorods obtained by the sol-gel method. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were measured using the AUTOLAB 302N potentiostat-galvanostat under Nova software. The EIS measurements were recorded in the frequency range 100 kHz to 10 mHz for...
Electrochemical impedance spectra and CV curves of V2O5 nanocrystals
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the EIS spectra for coin-cells and CV curves with the V2O5 nanocrystals obtained by the sol-gel method. Cyclic voltammetry and electrochemical impedance spectroscopy (EIS) were measured using the AUTOLAB 302N potentiostat-galvanostat under Nova software. The EIS measurements were recorded in the frequency range 100 kHz to 10 mHz...
Cycling performances of the V2O5 nanostructures as cathode material in Na-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next one hundred galvanostatic charge/discharge curves of the V2O5 nanostructures with different morphology obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with C/5 current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here...
Cycling performances of the V2O5 nanorods as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next one hundred galvanostatic charge/discharge curves of the V2O5 nanorods obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with C/5 and 2C current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1. The...
Cycling performances of the V2O5 nanocrystals as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next one hundred galvanostatic charge/discharge curves of the V2O5 nanocrystals obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with C/5 and 2C current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1. ...
Cyclic voltammetry curves of the V2O5 nanorods (Na-ion batteries)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanorods obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Na/Na+ at a scan rate of 1 mV/s. As an electrolyte 1M NaPF6 was applied.
Cyclic voltammetry curves of the V2O5 nanocrystals (Na-ion batteries)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanocrystals obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Na/Na+ at a scan rate of 1 mV/s. As an electrolyte 1M NaPF6 was applied.
Cyclic voltammetry curves of the V2O5 nanorods (Li-ion batteries)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanocrystals obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Li/Li+ at a scan rate of 1 mV/s. The results show that in the subsequent cycles,...
Cyclic voltammetry curves of the V2O5 nanocrystals (Li-ion batteries)
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the next thirty cycles voltammetry curves for the V2O5 nanocrystals obtained by the sol-gel method. The cyclic voltammetry was measured using the AUTOLAB 302N potentiostat-galvanostat. The measurements were carried out in a voltage range of 2 V to 4 V vs. Li/Li+ at a scan rate of 1 mV/s. The results show that in the subsequent cycles,...
Rate performance of the V2O5 nanorods as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the galvanostatic charge/discharge curves of the V2O5 nanorods obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with different current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1.
Rate performance of the V2O5 nanocrystals as cathode material in Li-ion batteries
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the galvanostatic charge/discharge curves of the V2O5 nanocrystals obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with different current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1.
SEM micrographs of V2O5 thin film morphology dependent on substrate types
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 thin film morphology dependent on substrate types. The as-prepared thin films were deposited on alumina, zirconium, zirconium oxide and metallic vanadium substrate, then was annealing under an oxidizing atmosphere at 600C for 10h. The results show that the morphology of...
SEM micrographs of morphology evolution of V2O5 thin films on quartz glass
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the scanning electron microscopy (SEM) micrographs of V2O5 thin films deposited on a quartz glass substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range 200-600C. The results show that the morphology of the films dependent on the annealing temperature.
XRD patterns of V2O5 thin film morphology dependent on substrate types
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of the V2O5 thin film structure dependent on substrate types. The as-prepared thin films were deposited on alumina, zirconium, zirconium oxide and metallic vanadium substrate, then was annealing under an oxidizing atmosphere at 600C for 10h.
XRD patterns of V2O5 thin films deposited on silicon substrate
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 thin films deposited on a silicon substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range of 300-600C. The results show that the structure of the films dependent on the annealing temperature.
XRD patterns of V2O5 thin films deposited on quartz glass
Dane Badawcze
- seria: Vanadium oxides
The DataSet contains the XRD patterns of V2O5 thin films deposited on a quartz glass substrate. The as-prepared thin films were annealing under an oxidizing atmosphere in the temperature range 200-600C. The results show that the structure of the films dependent on the annealing temperature.

seria: Magnetic flux leakage signals measured with different velocities liczba: 2

rozwiń zwiń

Magnetic flux leakage signals of far side defects measured with different velocities
Dane Badawcze
- seria: Magnetic flux leakage signals measured with different velocities
The dataset contains raw signals measured with the use of the magnetic flux leakage (MFL) technique. Linear Hall effect sensors A1324 were used to measure magnetic flux leakage. Three voltage signals were measured: Bx sensor output, Bz1 sensor output, and difference of Bz1 and Bz2 outputs. An output of a Bx sensor was directly proportional to the tangential...
Magnetic flux leakage signals of near side defects measured with different velocities
Dane Badawcze
- seria: Magnetic flux leakage signals measured with different velocities
The dataset contains raw signals measured with the use of the magnetic flux leakage (MFL) technique. Linear Hall effect sensors A1324 were used to measure magnetic flux leakage. Three voltage signals were measured: Bx sensor output, Bz1 sensor output, and difference of Bz1 and Bz2 outputs. An output of a Bx sensor was directly proportional to the tangential...

Acoustic emission studies of the 7075 aluminium alloy pitting corrosion process
Dane Badawcze
The dataset contains the cyclic polarization studies and corresponding acoustic emission measurements, revealing the pitting corrosion process of the passive layer at the surface of the 7075 aluminum alloy in the borate buffer with different chloride ions concentrations, in the range between 0.05 and 25 mM.
The microstructure of AA5754 alloy under corrosion in alkaline media (pH=11) with 20 mM of various carboxylic acids
Dane Badawcze
This dataset contains scanning electron microscopy (SEM) micrographs taken for polished aluminum AA5754 alloy samples, exposed for 100 min in bicarbonate buffer (pH=11) with the addition of 20 mM of carboxylic acids, namely: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, tricarballylic acid and serine. The goal of this study was...
The SEM micrographs of the cavitation erosion-corrosion process of selected copper alloys degradation
Dane Badawcze
The dataset contains Scanning Electron Micrographs of CuZn40Mn3Fe brass compared with Superston and Novoston bronze after cavitation erosion-corrosion exposure using a vibratory transducer (in accordance with ASTM G32). The micrographs compare the topography of samples subjected cavitation erosion in 3% NaCl at room temperature, leading to the surface...
Cyclic polarization studies of Mg corrosion in alkaline environment
Dane Badawcze
- J. Ryl
The dataset contains the cyclic polarization studies of Mg (99.99%) in NaOH electrolyte at different pH values: 10, 11 and 12 aiming at understanding of Mg(OH)2 passive layer formation mechanism and conditions. The electrochemical studies were carried out in a three electrode setup, with Pt mesh as the counter electrode and Ag|AgCl as the reference...
Ellipsometric monitoring during the polarization studies of Mg corrosion in alkaline environment
Dane Badawcze
- J. Ryl
The dataset contains the ellipsometric results from the Mg polarization studies aiming at understanding the Mg(OH)2 passive layer formation mechanism and conditions. The single-wavelength ellipsometer ELX-02C from Dr Riss GmbH was utilized, operating He-Ne laser at 632.8 nm. The polarization conditions for the experiment are depicted in the related...
The scanning electron microscopy (SEM) studies of low voltage copper cables
Dane Badawcze
- J. Ryl
- M. Olesz
The dataset contains the scanning electron microscopy (SEM) images of the low voltage copper cables, which were studied in the article discussing the regulatory requirements for checking the electrical resistance of such cables. The cables were cut and studies in cross-section. The full results were published in:
X-ray Photoelectron Spectroscopy studies of laser-induced titania nanotubes
Dane Badawcze
- J. Ryl
This dataset contains the results of high-resolution XPS studies obtained during the formation of the hollow nanopillar arrays through the laser-induced transformation of titania nanotubes.
The BDD electrodes wettability modification by anodic polarization treatment
Dane Badawcze
The dataset contains the raw images, photographs obtained for the contact angle measurement at the surface of the boron-doped diamond (BDD) electrode. The measurements were carried out on after potentiodynamic polarization procedure, at various anodic polarization scan range (no polarization - HTBDD; 1.0 V; 1.4 V; 1.9 V; 2.5 V vs Ag|AgCl, scan rate...
The scanning electron microscopy (SEM) studies of heavy boron-doped diamond oxidation under high-temperature
Dane Badawcze
The dataset contains the results of scanning electron microscopy (SEM) images of heavy boron-doped diamond (BDD) electrodes subjected to high-temperature oxidation in a furnace at 600 Celsius. The micrographs reveal the material decomposition of BDD grains due to high temperature.
SEM micrographs of the austenitic stainless steel corrosion in asphalt fumes
Dane Badawcze
The dataset contains the scanning electron microscopy (SEM) studies of the austenitic stainless steels: AISI 304, AISI 316, AISI 321 and duplex stainless steel AISI 2205. The samples were polished and exposed to the installation carrying asphalt fumes at elevated temperatures (approx. ~210-240 Celsius). The exposition duration was three months. Some...
The XPS studies revealing the surface chemistry of Cu-Sn-TiO2 nanocomposite coatings
Dane Badawcze
- J. Ryl
The dataset contains the X-Ray Photoelectron Spectroscopy (XPS) data of nanocomposite Cu-Sn-TiO2 coatings electrodeposited from oxalic acid bath containing Cu and Sn salts as well as TiO2 nanoparticles under various treatments: mechanical stirring, ultrasonic or none. The details of the electrodeposition process are presented in the descriptor file...
Scanning electron microscopy studies of the weld decay on SS 304 of water supply pipeline
Dane Badawcze
- J. Ryl
- J. Wysocka
This dataset contains micrographs made with scanning electron microscope (SEM) Hitachi S-3400N, of the weld decay for water supply system pipelines made of AISI 304 stainless steel. Within the dataset one can see the different corrosion mechanisms. The micrographs were made after the Strauss test (excluding pictures labeled as pits_in_HAZ, done without...
The photocatalytic activity of MoS2 electrodes under sunlight illumination
Dane Badawcze
- M. Szkoda
- J. Ryl
This dataset contains the results of the photocatalytic activities of the MoS2 and MoS2 modified by SnO2 were assessed through the photocatalytic reduction of Cr6+ under the sunlight illumination. In the experiment, 20 mg of the catalyst was distributed in the K2Cr2O7 aqueous solution (50 mL, 100 mg•L-1). The mixed solution was stirred for 30 min to...
The effect of different accelerators on the reclaiming efficiency of ground tire rubber
Dane Badawcze
The presented results concern the influence of different accelerators on the reclaiming efficiency of ground tire rubber (GTR). All the specimens were prepared using a two-roll mill and each sample was prepared in the same manner. Samples were submitted to curing analysis via Rheometer Monsanto 100S after 24 hours of aging. The attached data are related...
SEM micrographs of the topography of Cu-Sn-TiO2 nanocomposite coatings
Dane Badawcze
- J. Ryl
The dataset contains the scanning electron microscopy (SEM) micrographs of nanocomposite Cu-Sn-TiO2 coatings electrodeposited from oxalic acid bath containing Cu and Sn salts as well as TiO2 nanoparticles under various treatments: mechanical stirring, ultrasonic or none. The details of the electrodeposition process are presented in the readme file attached...
The AFM micrographs and impedance study of epoxy coatings after exposure in corrosive media
Dane Badawcze
- M. Szociński
- J. Ryl
The dataset contains Atomic Force Microscopy (AFM) images and local impedance measurements of epoxy organic coating used as anti-corrosion protection, before and after 2-month exposure to sodium chloride solution. Additionally, there two local impedance spectra recorded after the coating exposure. The first one was recorded on intact coating surface,...
SEM micrographs of boron-doped nanocrystalline diamond-carbon nanospikes
Dane Badawcze
This dataset contains the Scanning Electron Microscopy (SEM) micrographs taken for rich boron-doped carbon crystalline nanospikes/nanograss structures, at different magnifications, encoded in the labels of the images. The micrographs were made using Hitachi S-3400N SEM microscope in secondary electron mode under 20 kV accelerating voltage. No additional...
The electrochemical impedance spectroscopy studies of cataphoretic-grown epoxy-based coatings
Dane Badawcze
- M. Szociński
- A. Niczewska
- J. Ryl
The dataset contains electrochemical impedance spectroscopy spectra collected for epoxy-based cataphoretic coatings in order to determine the offered anti-corrosion protection. Particular spectra pertain to the coatings applied for the different magnitude of polarization potential imposed, namely 10V, 20V and 30V. The results were obtained within the...
Evaluation of antimicrobial properties of thermomelt adhesives modified with zinc compounds
Dane Badawcze
The dataset contains the results of microbiological tests of thermomelt adhesives modified with zinc compounds, whose activity was assessed for their ability to reduce the number of Escherichia coli and Staphylococcus aureus strain, representing the Gram (-) and Gram (+) bacteria, respectively. The evaluation of antimicrobial properties of samples were...
SEM micrographs of Ti tooth implant corrosion
Dane Badawcze
- J. Ryl
The dataset contains micrographs made with a scanning electron microscope (SEM) Hitachi S-3400N of the tooth implant removed after inflammation. The inflammation was induced by the increased corrosion rate of the titanium screw. The reason for the corrosion to occur was the appearance of the concentration cell of different aeration for various areas...
The hydrogen evolution reaction (HER) performance of some FTO/MoS2/SnO2 electrodes
Dane Badawcze
- M. Szkoda
- J. Ryl
To demonstrate the electrochemical performance of the FTO/MoS2/SnO2 for HER (hydrogen evolution reaction), the LSV (linear sweep voltammetry) was performed. The polarization curves of the obtained composite were measured in 1 M H2SO4 at room temperature with a scan rate 10 mV/s. For comparison, the LSV for the FTO, pure MoS2 and Pt plate electrode were...
SEM micrographs of aluminium corrosion in alkaline media with various bee products as corrosion inhibitors
Dane Badawcze
- J. Jasonek
- J. Ryl
This dataset contains various scanning electron microscopy (SEM) micrographs of AA5754 aluminum alloy samples exposed to the corrosive alkaline environment without and with the addition of various bee products to act as green corrosion inhibitors. The products are bee pollen, honey, and putty. They were investigated in bicarbonate buffer (pH =10 or...
Sensory analysis of bread samples with the addition of beetroot
Dane Badawcze
- S. Mania
- R. Tylingo
- A. Sommer
- J. Ryl
The data set presents the results of the sensory analysis of bread samples with the addition of beetroot, which was carried out by the sensory profiling analysis method based on the PN-ISO 11035: 1999 standard – “Sensory analysis - Identification and selection of descriptors for determining the sensory profile using multivariate methods”. The method...
Curing characteristics of ground tire rubber modified by commercial additives
Dane Badawcze
The presented results show the influence of commercially available bitumen and transoctenamer rubber (TOR) on the curing behavior of GTR treated by a peroxide. Samples were prepared using a two-roll mill– all in the same manner. After 24 hours of aging at ambient conditions, they were submitted to the curing analysis via Rheometer Monsanto 100S. The...
Curing characteristics and Mooney viscosity of reclaimed rubbers
Dane Badawcze
Presented data shows the difference in curing characteristics and Mooney’s viscosity between commercially available reclaimed rubbers and ground tire rubber (GTR) with specific particle size distribution cured with the same curing system and with the same manner. Samples were prepared using a two-roll mill. After 24 hours of aging at ambient conditions,...
The impact of carbon black particle size on curing characteristics of GTR modified with bitumen
Dane Badawcze
Presented data shows an impact of particle size of GTR and three different loadings of carbon black on curing characteristics of GTR modified with bitumen. Samples were prepared using a two-roll mill – all in the same manner. After 24 hours of stabilization at ambient conditions they were submitted to the curing analysis via Rheometer Monsanto 100S....
Cyclic voltammetry curves for FTO/PANI:WO3 nanocomposite
Dane Badawcze
- M. Szkoda
- J. Ryl
This dataset contains the results of kinetic electrochemical studies, carried out with cyclic voltammetry (CV) of FTO/PANI:WO3 nanocomposite at various scan rates: 10, 20, 50, 75, 100 and 200 mV/s. The electrolyte was 1M H2SO4 solution. The measurements were performed in a three electrode setup, and with Ag|AgCl|3M KCl as the reference electrode and...
SEM micrographs of cavitation erosion-corrosion of aluminium alloy 2024 with anodic polarization
Dane Badawcze
- J. Ryl
- P. Rysztak
The dataset contains Scanning Electron Micrographs of aluminium alloy 2024 samples made after cavitation erosion-corrosion exposure using a vibratory transducer (in accordance with ASTM G32). The experiment duration was 240 min, with cyclic cavitation exposure in on/off cycles 30s:30s. The electrolyte was 0.1 M KNO3 solution. Some samples were anodically...
The effect of cobalt addition on the corrosion behavior of near equiatomic NiTi shape memory alloy in normal saline solution, impedance and microscopic studies
Dane Badawcze
- J. Ryl
- J. Wysocka
The electrochemical and corrosion (uniform and localized) behavior of a binary Ni52Ti48 shape memory alloy (SMA) and two ternary Ni52Ti48-xCox (x = 1.5 and 4.0 wt.%) SMAs were studied. Measurements were conducted in 0.9% NaCl solution at 37 oC. This dataset contains the results of electrochemical impedance spectroscopy (EIS) studies done on daily basis...
The SEM micrographs of the synergistic action between cavitation erosion and pitting corrosion on stainless steel 304
Dane Badawcze
- J. Ryl
- K. Sulej
The dataset contains Scanning Electron Micrographs of stainless steel AISI304 samples made after cavitation erosion-corrosion exposure using a vibratory transducer (in accordance with ASTM G32). The micrographs compare the topography of samples subjected to either cavitation erosion (in deionized water), pitting corrosion (in 8% FeCl3 solution, without...
The Scanning Electron Microscopy images of three arthropods
Dane Badawcze
- J. Ryl
The dataset contains micrographs of various arthropods made with the Scanning Electron Microscopy (SEM) technique. The images were done during the laboratory with students from the Faculty of Chemistry. Among the studied species, there is a fruit fly (lat.Drosophila melanogaster), a spider (most likely Sibianor aurocinctus), and a weevil insect (Curculionoidea).
Dynamic impedance data for various carboxylic acids corrosion inhibition of aluminium in alkaline media (pH=11)
Dane Badawcze
This dataset contains the results of Dynamic Electrochemical Impedance Spectroscopy (DEIS) carried out in galvanostatic mode under iDC=0, carried out in order to define the corrosion inhibition effect of various studied carboxylic acids: citric acid, malic acid, maleic acid, succinic acid, tartaric acid, carballylic acid, and serine. The experiment...
The influence of microstructure on the corrosion resistance for some titanium-based alloys
Dane Badawcze
- J. Ryl
- J. Wysocka
- M. Amin
This dataset contains scanning electron microscopy (SEM) micrographs revealing the microstructure of some Ti-based alloys, namely: Ti-6Al-4V (file name: TiV), Ti-6Al-7Nb (file name: TiNb) and TC21 (file name: TiAlSnZrMoCrNbSi) alloys and their localized corrosion as a result of passive layer breakdown in a corrosive environment, ie. 0.9% NaCl solution...
X-ray Photoelectron Spectroscopy studies of salivary gland stones
Dane Badawcze
- J. Ryl
- D. Tretiakow
This dataset contains the high-resolution XPS studies for 23 cross-sections of salivary gland stones. The sialoliths were cut to determine the differences in composition between various regions: core (labeled as R), interlayer (labeled as P) and sialolith surface (labeled as Z).
SEM micrographs and photos of salivary gland stones
Dane Badawcze
This dataset contains SEM micrographs and high-resolution photographs taken for salivary gland stones (sialolith) extracted during joint studies between Medical University of Gdansk and Gdansk University of Technology.
The microstructure of aluminium alloys AA1050 and AA7075 subjected to anodic polarization at 8V in KOH electrolyte
Dane Badawcze
The dataset contains SEM pictures of the microstructure of aluminum alloy AA1050 and AA7075 exposed in aqueous KOH in the pH range between 14–11. Two sets of samples are presented, revealing the topography of the alloys when exposed to aggressive media under open circuit potential conditions as well as when subjected potentiodynamic polarization ranging...
Model dynamic electrochemical impedance spectroscopy (DEIS) results obtained with various DC polarization rates
Dane Badawcze
- J. Wysocka
- J. Ryl
The dataset contains results of model dynamic electrochemical impedance spectroscopy studies carried out on a setup of 10 diodes in series, which were connected in parallel with a condenser. The impedance data were acquired every 1 s (the analytic window length for Fourier Transform was 1 s). The model system was polarized between 0 and +8 V with DEIS...
SEM micrographs of diamond-phase (sp3-C) rich boron-doped carbon nanowalls (sp2-C)
Dane Badawcze
This dataset contains the Scanning Electron Microscopy (SEM) micrographs taken for rich boron-doped carbon nanowalls structures, with different boron addition during the synthesis process and different CVD synthesis duration. The [B]/[C] ratios in the plasma were set to 0k, 1.2k, 2k and 5k ppm. The time of growth was ranging between 4 and 9 hours. This...
X-ray Photoelectron Spectroscopy studies of various carboxylic acids adsorption on aluminium alloys in alkaline media
Dane Badawcze
This dataset contains the results of high-resolution XPS studies obtained during evaluation of high corrosion inhibition efficiency of various carboxylic acids towards aluminium alloy 5754 in bicarbonate buffer pH=11.
Impedance and cyclic voltammetry studies of GPLA electrodes after laser ablation
Dane Badawcze
- J. Ryl
- M. Głowacki
The 3D printed GPLA electrodes present a brand new opportunity for electrode material for electrochemical biosensors. In order for the electrodes to be considered viable for electroanalysis studies, the pretreatment procedure must be applied in order to etch PLA matrix and reveal graphene filler. The following dataset presents an approach towards such...
X-ray Photoelectron Spectroscopy studies of citric acid adsorption on aluminium alloy 5754 in alkaline media
Dane Badawcze
This dataset contains the results of high-resolution XPS obtained during evaluation of high corrosion inhibition efficiency of citric acid towards aluminium alloy 5754 in bicarbonate buffer pH=11. The exposition duration of samples to electrolytic environment was 100 min. Each sample was exposed at different citric acid concentration ranging from 0...

wyświetlono 12517 razy

Wyszukiwarka

dr hab. inż. Jacek Ryl

Zatrudnienie

Obszary badawcze

seria: Additive manufacturing technology of electroactive three-dimensional structures from diamond reinforced polylactide composites liczba: 38

seria: Electrochemical Au-Minecraft: a new approach towards the impedimetric biosensing system liczba: 12

seria: Scanning Probe Microscopies data liczba: 49

seria: TeO2-based materials liczba: 20

seria: Ammonium vanadate liczba: 19

seria: Vanadium oxides liczba: 92