Filtry
wszystkich: 1858
wybranych: 1710
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXPERIMENTAL RESULTS
-
Assessing Word Difficulty for Quiz-Like Game
PublikacjaMappings verification is a laborious task. Our research aims at providing a framework for manual verification of mappings using crowdsourcing approach. For this purpose we plan on implementing a quiz like game. For this purpose the mappings have to be evaluated in terms of difficulty to better present texts in respect of game levels. In this paper we present an algorithm for assessing word difficulty. Three approaches...
-
Numerical Modelling of Shear Localization in Granular Bodies using MPM and Non-local Hypoplasticity
PublikacjaThe paper deals with modelling of shear localization in granular bodies by means of an enhanced hypoplastic constitutive model and material point method (MPM). The calculations were carried out for plane strain compression of non-cohesive sand. In order to properly capture the width and inclination of shear zones, the constitutive model was enriched by a characteristic length of micro-structure by means of a non-local theory....
-
Wpływ posuwu nagniatania na chropowatość powierzchni przedmiotów ze stali w stanie utwardzonym
PublikacjaPrzedstawiono wyniki badań eksperymentalnych procesu nagniatania stali twardej (62 HRC) narzędziem ceramicznym (kulką) z dociskiem hydrostatycznym. Analizowano wpływ posuwu nagniatania oraz parametrów poprzedzającej obróbki toczeniem na twardo na stan powierzchni opisanej wybranymi parametrami chropowatości.
-
Quality assessment of ZnO-based varistors by 1/f noise
PublikacjaNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Optimization of chip removing system operation in circular sawing machine
PublikacjaThe paper presents the optimization of the wood chips removing system in the sliding table saw. Chips are generated during the cutting of the material. The attention was focused on the upper casing of mentioned system. The methodical experimental studies of the pressure distribution inside the casing during the wood chip removing operation for the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm were...
-
Can we rely on the pulse transit time - pressure relationship - models comparison
PublikacjaAn unobtrusive, noninvasive and continuous pressure measurement is invaluable however, still being under research and development. There are many attempts proposing an appropriate relationship between pulse pressure velocity and pressure. Fifteen different formulas, both theoretical and experimental, describing relation between blood pressure and crosssectional area of the vessel were examined. Using these formulas the relation...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
A BRIEF REVIEW AND COMPARISON OF SELECTED EXPERIMENTAL METHODS FOR MEASURING NATURAL FREQUENCIES OF CIRCULAR SAW BLADES
PublikacjaDifferent methods for the empirical determination of the natural frequencies of circular saw blades are presented. Stationary methods, such as the harmonic and impulse tests, are discussed and the results of related comparison are given. The comparison of the methods revealed their degree of practical usefulness and their accuracy in determining natural frequencies. A combination of specific methods is proposed, which should allow...
-
EXPERIMENTAL STUDY OF SURFACE ROUGHNESS EFFECT ONTHE RHEOLOGICAL BEHAVIOR OF MR FLUID
PublikacjaPaper presents the results of shear stress measurements of a commercial magnetorheological fluid using a plate-plate type geometry with a modified working surface. The purpose of the study was to determine the effect of changing the roughness of the measuring plate on the obtained shear stress results. Controlled shear rate tests and Magneto Sweep measurements were carried out for three MR fluid layer heights. The tests were...
-
Evaluation of the significance of the effect of the active cross-sectional area of the inlet air channel on the specific enthalpy of the exhaust gas of a diesel engine using statistics F of the Fisher-Snedecor distribution
PublikacjaThis paper presents the application of Fisher-Snedecor distribution F statistics to assess the significance of the influence of changes in the active cross-sectional area of the inlet air channel (Adol) flow in a diesel engine on the observed diagnostic parameter determined on the basis of measurements of the quick changing exhaust gas temperature in the outlet channel, which is the specific enthalpy of the exhaust gas stream within...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Linking optical and electronic properties to photoresponse of heterojunctions based on titania nanotubes and chromium, molybdenum, and tungsten oxides
PublikacjaThe development of photosensitization strategies for titanium dioxide is necessary for the enhancement of its optical and electronic properties towards its application potential in solar photoelectrochemistry. In this work, significant differences in the photosensitizing capability of the 6th group transition metal oxides applied on the surface of titania nanotubes are reported. For the first time, correlations between the experimentally...
-
BADANIE WPŁYWU INDUKCJI REMANENCJI NA STAN PRZEJŚCIOWY JEDNOFAZOWEGO UKŁADU TRANSFORMATOROWEGO
PublikacjaW referacie przedstawiono wyniki badań eksperymentalnych i symulacyjnych wpływu indukcji remanencji w rdzeniu transformatora jednofazowego na jego stan przejściowy przy jego pracy jałowej. Badany obiekt jest układem transformatorowym o dwóch uzwojeniach nawiniętych na zwijanym z blachy anizotropowej rdzeniu w kształcie toroidu. Doświadczenia eksperymentalne polegały na rozładowywaniu kondensatora przez uzwojenie strony pierwotnej...
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublikacjaThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Is mesh fixation necessary in laparoendoscopic techniques for M3 inguinal defects? An experimental study.
Publikacjarepairs, in case of large direct hernias (M3) mesh fixation is recommended to reduce recurrence risk. Despite lack of highquality evidence, the recommendation was upgraded to strong by expert panel. The authors conducted a research experiment to verify the hypothesis that it is possible to preserve the mesh in the operating field in large direct hernias (M3) without the need to use fixing materials. Method The authors conducted...
-
Electron ionization and low energy electron attachment to molecules of biological interest
PublikacjaEthylenediaminetetraacetic acid (EDTA) and 2-amino-2-(hydroxymethyl)-1,3-propanediol (TRIS) were investigated by electron impact ionization and low energy electron attachment. Both compounds are components of biological buffers and often are used as DNA stabilizers in irradiation studies. hus it is of a great importance to understand their potential interactions with radiation. Our results revealed that at least one of them, EDTA, may...
-
Analysis of inductive power transfer systems for variable air gap and voltage supply frequency
PublikacjaThe paper describes an IPT system, by which electrical energy may be transmitted through a large air gap between coils without electrical connection. It presents theoretical and simulation analysis of IPT, which allows for supplying a receiver in the conditions of slow, in relation to the dynamics of power supply, changes in dimension of the air gap. The influence of frequency characteristics of the system on the possible selection...
-
Electron ionization and low energy electron attachment to molecules of biological interest
PublikacjaEthylenediaminetetraacetic acid (EDTA) and 2-amino-2-(hydroxymethyl)-1,3-propanediol (TRIS) were investigated by electron impact ionization and low energy electron attachment. Both compounds are components of biological buffers and often are used as DNA stabilizers in irradiation studies. hus it is of a great importance to understand their potential interactions with radiation. Our results revealed that at least one of them, EDTA, may...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
Evaluation of compression realization in diesel engine based on performance indicator changes
PublikacjaIn the article a method of evaluation of a diesel engine during the realization of processes of working cycle on the example of compression is described. The method is based on the use of the quantity called performance indicator in the description of the engine's work, which contains the information on the energy values, which may be disposed using the engine and the time at which it can be delivered. Theoretical information has...
-
Validation of a sampling procedure
PublikacjaEach step of the analytical procedure influences the final results in a significant way. In the majority of cases the analytical procedure encompasses sampling because the analysis of the entire object (material) is usually not possible. Thus it is necessary to include the uncertainty related to sampling procedure in the uncertainty budget calculations. This paper describes two basic ways of estimating the sampling uncertainty,...
-
Badania eksperymentalne transformatora hybrydowego jako kondycjonera napięcia w sieciach typu TN
PublikacjaArtykuł dotyczy układu dystrybucyjnego transformatora hybrydowego (DTH) przeznaczonego do zastosowania w sieciach typu TN. Opisano w nim sposoby podłączenia przewodu neutralnego do układu DTH. W dalszej części artykuł zawiera opis skonstruowanego modelu laboratoryjnego o mocy 16 kVA wraz z zastosowanym algorytmem sterowania. Ponadto przedstawiono wyniki badań eksperymentalnych, ze szczególnym uwzględnieniem oceny dokładności stabilizacji...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublikacjaNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on...
-
Numerical analysis of the container vessel's self-propulsion at different rudder deflection angles
PublikacjaNowadays, CFD becomes one of the most commonly used research method in ship hydrodynamics, limited to the analyses of hull resistance in calm water. With continuously improving computing power and increasingly more accurate numerical methods it is possible to simulate more complex cases. State of the art CFD tools also enable development of new ways of assessing ship maneuvering performance. This paper presents an attempt on using...
-
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublikacjaThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Experimental study on the behaviour of steel columns under seismic-induced axial impact load
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. Therefore, the aim of this paper is to investigate experimentally the behaviour of columns under bending (observed...
-
Flexural behaviour of concrete slabs reinforced with FRP bars in experiments and according to aci ACI 440.1R guide
PublikacjaThe paper presents research conducted on two concrete slabs reinforced with the carbon composite bars and two other concrete slabs reinforced with basalt composite bars. The carbon bars were plain, while the basalt ones were ribbed. The slabs were experimentally investigated in the flexural state of effort with the concentrated forces applied. The results are compared with the analytical solution proposed in the guide ACI 440.1R-06...
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublikacjaThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
HYDROACOUSTIC NOISE MEASUREMENTS
PublikacjaThe paper deals mainly with investigation of underwater noise that propagation is in shallow water. In this paper has been presented the experimental investigation results concerning the distribution of the sound field pressure generated by moving ships in the shallow water at the small distance from the ship. The main acoustical characteristics describing features of the field are spectrograms in pseudo 3D system – distance and frequency...
-
Preliminary estimation of groundwater recharge on Brda river outwash plain
PublikacjaEstimation of groundwater recharge is one of the most challenging subjects in hydrogeology. It is a critical factor influencing the pollution migration, assessment of aquifer vulnerability to contamination, small-scale groundwater budget calculation, modeling of nutrient cycling and detailed flow path calculations. In Poland an infiltration rate method is widely used, which depends on a system of rate coefficients referring to...
-
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublikacjaThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
Manoeuvring forces on azimuthing podded propulsor model
PublikacjaThis paper presents the preliminary part of comprehensive manoeuvring open- water tests of a gas carrier model. The paper focuses on open water experiments with an azimuthing podded propulsor. The test program was carried out in the cavitation tunnel and the large towing tank of Ship Hydromechanics Division, Ship Design and Research Centre, Gdańsk. The pod was tested as a pushing unit with a 161.3 mm diameter propeller. Steering...
-
CFD Simulations and Tests of a Prototype Flow Control Valve
PublikacjaIn this paper a prototype of a flow control valve is described and numerically simulated. The flow control valve is used in hydraulic systems to maintain constant fluid flow despite changing loads of a receiver. The standard construction of this type of valves is modified mainly by eliminating the spring. The prototype consists the hydrostatically unloaded throttle valve and pressure ratio valve substituting pressure difference...
-
Uniform sampling in constrained domains for low-cost surrogate modeling of antenna input characteristics
PublikacjaIn this letter, a design of experiments technique that permits uniform sampling in constrained domains is proposed. The discussed method is applied to generate training data for construction of fast replacement models (surrogates) of antenna input characteristics. The modeling process is design-oriented with the surrogate domain spanned by a set of reference designs optimized with respect to the performance figures and/or operating...
-
Born–Oppenheimer potential energy curves of NaK from the optimised atomic basis sets
PublikacjaThe article presents adiabatic potential energy curves of the ground and excited electronic states for the diatomic NaK molecule. The calculations were made using the ab initio computational methods to include electron correlation. The studied molecule was calculated as the effective two-electron problem, in which only the valence electrons of the molecule are explicitly taken into account. The remaining electrons with atomic nuclei...
-
Pressure effects on the superconductivity of the HfPd2Al Heusler compound: Experimental and theoretical study
PublikacjaPolycrystalline HfPd2Al has been synthesized using the arc-melting method and studied under ambient-pressure conditions by x-ray diffraction from room temperature up to 450 °C. High-pressure x-ray diffraction up to 23 GPa was also performed using Diacell-type membrane diamond anvil cells. The estimated linear thermal expansion coefficient was found to be α=1.40(3)×10−5K−1, and the bulk modulus derived from the fit to the third-order...
-
Discrete element method modelling of elastic wave propagation in a meso-scale model of concrete
PublikacjaThis paper deals with the accurate modelling of ultrasonic wave propagation in concrete at the mesoscopic level. This was achieved through the development of a discrete element method (DEM) model capable of simulating elastic wave signals comparable to those measured experimentally. The main objective of the work was to propose a novel methodology for constructing a meso-scale model of concrete dedicated to the analysis of elastic...
-
On the Matano Plane Position in Multicomponent Diffusion Couples
PublikacjaEven though several methods of diffusion analysis avoid a necessity for the Matano plane determination, the Matano plane locations are of interest in the multicomponent couples and when tracer experiments are performed. The positions of the Matano plane calculated from the concentration profiles should be exactly the same. However, due to experimental errors, the results can differ significantly. In the paper we consider Matano...
-
On the Matano Plane Position in Multicomponent Diffusion Couples
PublikacjaEven though several methods of diffusion analysis avoid a necessity for the Matano plane determination, the Matano plane locations are of interest in the multicomponent couples and when tracer experiments are performed. The positions of the Matano plane calculated from the concentration profiles should be exactly the same. However, due to experimental errors, the results can differ significantly. In the paper we consider Matano...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublikacjaResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
-
Numerical assessment of ultimate strength of severe corroded stiffened plates
PublikacjaThe objective of this work is to investigate numerically (using the non-linear FEM and the approach stipulated by the Common Structural Rules) the severe nonuniform corrosion degradation effect on the ultimate strength of stiffened plates and compare the results to the already published experimental works. Different factors governing structural behavior of corroded stiffened plates are investigated, such as corrosion degradation level,...
-
Ultimate strength of stiffened plates subjected to compressive load and spatially distributed mechanical properties
PublikacjaThe present study deals with the ultimate strength of stiffened plates subjected to spatially distributed mechanical properties and compressive load. Normally, mean values of mechanical properties based on tensile tests are used to validate the numerical assessment with experimental results. However, mechanical properties may vary within a single specimen. To investigate the impact of that, random fields of yield stress and Young...
-
Design and Experiments of a Piezoelectric Motor Using Three Rotating Mode Actuators
PublikacjaThis paper represents a numerical and experimental investigation of the multicell piezoelectric motor. The proposed design consists of three individual cells that are integrated into the stator, double rotor, and a preload system combined into a symmetrical structure of the motor. Each of the cells is characterized by a traveling wave and rotating mode motor. A finite element numerical analysis is carried out to obtain optimal...
-
Guanosine Dianions Hydrated by One to Four Water Molecules
PublikacjaIntermolecular interactions such as those present in molecule···water complexes may profoundly influence the physicochemical properties of molecules. Here, we carried out an experimental–computational study on doubly deprotonated guanosine monophosphate···water clusters, [dGMP – 2H]2–·nH2O (n = 1–4), using a combination of negative anion photoelectron spectroscopy (NIPES) with molecular dynamics (MD) and quantum chemical (QM) calculations....
-
Size effect at aggregate level in microCT scans and DEM simulation – Splitting tensile test of concrete
PublikacjaThe paper describes an experimental and numerical study of size effect on concrete cylindrical specimens in splitting tensile test. Own experimental campaign was performed on specimens with 5 various diameters from D = 74, 105, 150, 192 and 250 mm with hardboard loading strips (distributed load according to standard methods) scaled proportionally to the specimen diameter. The crack opening-control system was applied to obtain the...
-
Experimental research of the stability of steel cylindricalshell subjected to circumferential compression
PublikacjaAt the Department of Metal Structures Gdańsk University of Technology, experiments have been performed on the stability of shell of steel cylindrical models. The experiments have been carried on a test bench built at the Department. The design based on other test benches which were created in the past by other scientists, where modernized by the courtesy of companies that offer modern solutions. The test bench enables to generate...
-
Experimental investigation of domestic gas boiler fitted with ORC module
PublikacjaIn the paper the prototype of innovative domestic cogenerative ORC system, consisting of a conventional gas boiler and a small size axial vapour microturbines (in-house designed for ORC and the commercially available for Rankine cycle (RC)), evaporator and condenser were scrutinised. In the course of study the fluid working temperatures, rates of heat, electricity generation and efficiency of the whole system were obtained. The...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Experimental and Numerical Study on Mechanical Characteristics of Aluminum/Glass Fiber Composite Laminates
PublikacjaThe fiber-metal composites made of aluminum sheets and glass fibers reinforced with a polyester resin as the matrix were studied. The composites were prepared by hand lay-up method. Some aspects of manufacturing affecting the composite behavior were considered. In particular, the influences of the arrangement of layers and their number on the mechanical and physical properties of composites with ten different compositions were...