Filtry
wszystkich: 1508
wybranych: 1339
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: electrical power quality parameters
-
Subjective and Objective Quality Evaluation Study of BPL -PLC Wired Medium
PublikacjaThis paper presents results of research on the effectiveness of bi-directional voice transmission in a 6 kV mine cable network using BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It concerns both emergency cable state (supply outage with cable shorted at both ends) and loaded with distorted current waveforms. The narrowband (0.5 MHz–15 MHz) and broadband (two different modes, frequency range of 3 MHz–7.5...
-
Subjective Quality Evaluation of Speech Signals Transmitted via BPL-PLC Wired System
PublikacjaThe broadband over power line – power line communication (BPL-PLC) cable is resistant to electricity stoppage and partial damage of phase conductors. It maintains continuity of transmission in case of an emergency. These features make it an ideal solution for delivering data, e.g. in an underground mine environment, especially clear and easily understandable voice messages. This paper describes a subjective quality evaluation of...
-
The Conceptual Research over Low-Switching Modulation Strategy for Matrix Converters with the Coupled Reactors
PublikacjaIn this paper, different Pulse Width Modulation (PWM) strategies for operating with a low-switching frequency, a topology that combines Conventional Matrix Converters (CMCs), and Coupled Reactors (CRs) are presented and discussed. The principles of the proposed strategies are first discussed by a conceptual analysis and later validated by simulation. The paper shows how the combination of CMCs and CRs could be of special interest...
-
Control of a vapour microturbine set in cogeneration applications
PublikacjaSystems with microturbines are implemented for local generation of heat and electricity. This paper presents the analysis of control concepts for a vapour microturbine set with a generator with permanent magnets, intended to work in small heat and power plants. Control system variants differed by the selection of controlled signals and set parameters. Possible ways of control were discussed and compared with experimentally determined...
-
Wpływ błędów parametrów modelu maszyny indukcyjnej na działanie rozszerzonego obserwatora prędkości
PublikacjaW artykule opisano metodę odtwarzania prędkości wirnika maszyny indukcyjnej przy wykorzystaniu rozszerzonego obserwatora prędkości. Zbadano wpływ błędów parametrów modelu maszyny indukcyjnej na właściwości dynamiczne obserwatora poprzez porównanie macierzy stanu obserwatora obarczonego oraz nieobarczonego błędami parametrów. Zbadany został także wpływ błędów parametrów na jakość odtwarzania zmiennych maszyny w stanie ustalonym.
-
Syntetyczne wskaźniki oceny stanu toru
PublikacjaJakość geometryczna toru analizowana jest w różnych celach, a dane podlegają różnemu stopniowi agregacji. Pojedyncze nierówności toru analizowane są zazwyczaj z uwagi na bezpieczeństwo i służą do planowanie napraw w krótkich terminach. Natomiast agregacja pomierzonych parametrów pozwala na planowanie robót w terminach średniookresowych i budowę modeli predykcji. W artykule przedstawiono zagregowane wskaźniki jakości geometrycznej...
-
Wysokoczęstotliwościowy falownik napięcia - badania symulacyjne
PublikacjaWiększość ruchomych odbiorników energii elektrycznej jest połączona ze źródłem energii poprzez: giętkie przewody, komutatory, pierścienie ślizgowe lub pantografy. Taki sposób zasilania w energię elektryczną jest powszech-nie akceptowalny w łagodnym środowisku pracy, ale może być ograniczony w środowisku zagrożonym pod względem wybuchu lub wilgotnym. W wielu przypadkach zastosowań trakcyjnych warunki środowiskowe nie pozwalają na...
-
Flow Boiling in Minigap in the Reversed Two-Phase Thermosiphon Loop
PublikacjaThe paper presents the results of experimental investigations of a model of a heat exchanger featuring a minigap, which is perceived as an evaporator for an inverted thermosiphon. The system works with a single component test fluid. The tested evaporator generates pumping power in the test loop in a way similar to the mammoth pump. The tests regarded a module of the heat exchanger, consisting of a hot leg and a cold leg with the...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublikacjaThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
Efficiency Evaluation of High Performance Computing Systems Using Data Envelopment Analysis
PublikacjaThe paper presents an evaluation method of high performance computing (HPC) systems using multicriteria efficiency analysis. The Data Envelopment Analysis approach was applied and adapted to the specifics of HPC, which enabled us to compare relative efficiency of systems considering simultaneously multiple parameters. The analysis is based on the TOP500 list of world largest supercomputers and their parameters such as: the number...
-
TERMODYNAMIC CALCULATIONS OF TURBINE STEAM PARAMETERS
PublikacjaIn this work a heat balance was made for the nominal conditions of a block working with 18K370 turbine. For the parameters obtained, the thermal-flow calculations of the steam turbine were performed, maintaining the actual geometry of its flow system. Based on the nominal values obtained, iterative thermal and flow calculations were made for both the heat cycle of the power plant block and the steam turbine itself, seeking to obtain...
-
Recent advances in high-frequency modeling by means of domain confinement and nested kriging
PublikacjaDevelopment of modern high-frequency components and circuits is heavily based on full-wave electromagnetic (EM) simulation tools. Some phenomena, although important from the point of view of the system performance, e.g., EM cross-coupling effects, feed radiation in antenna arrays, substrate anisotropy, cannot be adequately accounted for using simpler means such as equivalent network representations. Consequently, the involvement...
-
Laboratory Load Model Based on 150 kVA Power Frequency Converter and Simulink Real-Time – Concept, mplementation, Experiments
PublikacjaFirst section of the paper provides technical specification of laboratory load model basing on 150 kVA power frequency converter and Simulink Real-Time platform. Assumptions, as well as control algorithm structure is presented. Theoretical considerations based on criteria which load types may be simulated using discussed laboratory setup, are described. As described model contains transformer with thyristor-controlled tap changer,...
-
Thermodynamic and economic analysis of nuclear power unit operating in partial cogeneration mode to produce electricity and district heat
PublikacjaThis paper presents the methodology of techno-economic analysis for a nuclear unit operating in partial cogeneration mode and its application for the case study: a nuclear power plant planned in Poland. The research objectives were: to propose EPR, AP1000 and ESBWR nuclear condensing-extraction turbine systems modifications required for operation in cogeneration, to determine optimal heat production and heat transport line (HTL)...
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublikacjaMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Resource constrained neural network training
PublikacjaModern applications of neural-network-based AI solutions tend to move from datacenter backends to low-power edge devices. Environmental, computational, and power constraints are inevitable consequences of such a shift. Limiting the bit count of neural network parameters proved to be a valid technique for speeding up and increasing efficiency of the inference process. Hence, it is understandable that a similar approach is gaining...
-
Application of Multivariate Adaptive Regression Splines (MARSplines) for Predicting Hansen Solubility Parameters Based on 1D and 2D Molecular Descriptors Computed from SMILES String
PublikacjaA new method of Hansen solubility parameters (HSPs) prediction was developed by combining the multivariate adaptive regression splines (MARSplines) methodology with a simple multivariable regression involving 1D and 2D PaDEL molecular descriptors. In order to adopt the MARSplines approach to QSPR/QSAR problems, several optimization procedures were proposed and tested. The effectiveness of the obtained models was checked via standard...
-
Dynamiczna aplikacja Internetowa ASP.NET silnika indukcyjnego jako elementu wirtualnego laboratorium maszyn elektrycznych
PublikacjaTematem referatu jest dynamiczna aplikacja internetowa, która umożliwia symulację obwodową silnika indukcyjnego trójfazowego Sg 100 L2 z wykorzystaniem interfejsu przeglądarki WWW. Model matematyczny silnika jest zdefiniowany w tzw. osiach naturalnych i sformułowany na podstawie metody energetycznej Lagrange’a. Do implementacji modelu maszyny w aplikacji internetowej wybrano projekt typu Web Forms, który jest składnikiem środowiska...
-
Skutki zwarć łukowych w średnionapięciowych rozdzielnicach okrętowych z izolacją powietrzną
PublikacjaW artykule scharakteryzowano moc i napięcie łuku, jak również przedstawiono model termodynamiczny służący do obliczania ciśnienia i temperatury gazów w otoczeniu łuku zwarciowego. Przedstawiono przykładowy układ elektrowni okrętowej i zasilania najważniejszych odbiorników na statku do przewozu kontenerów, w tym 600 kontenerów chłodzonych. Na podstawie parametrów prądnic i silników, odbiorników zasilanych z rozdzielnicy głównej...
-
Installation of CMC columns in overconsolidated clays
PublikacjaDuring rigid inclusions execution in the subsoil some monitoring data are registered by a drilling rig for quality control. The use of these data can improve the design procedure of soil improvement as they can provide some information about the position of bearing strata and the energy necessary to install the column in the ground. In this paper the parameters registered in a drilling machine are described, the installation...
-
MEAN SHIFT BASED SEGMENTATION FOR BLEEDING REGIONS IN ENDOSCOPIC VIDEOS
PublikacjaWith a set of 38 manually marked bleeding regions form endoscopic videos, the authors attempted to find an optimal image segmentation method for reproducing doctor’s markup. Mean shift segmentation combined with HSV histogram segmentation were used as a segmentation method, which was then optimized by tuning the parameters of the method using global optimization algorithm. A target function for measuring the quality of segmentation was...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublikacjaA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
Application of Thermo-chemical Technologies for Conversion of Associated Gas in Diesel-Gas Turbine Installations for Oil and Gas Floating Units
PublikacjaThe paper considers the issue of thermo-chemical recovery of engine’s waste heat and its further use for steam conversion of the associated gas for oil and gas floating units. The characteristics of the associated gas are presented, and problems of its application in dual-fuel medium-speed internal combustion engines are discussed. Various variants of combined diesel-gas turbine power plant with thermo-chemical heat recovery are...
-
Modelling of dielectric properties of BiNbO4-based microwave ceramics
PublikacjaIn the present paper results of the studies devoted to computer simulations of dielectric response of electroceramics in a frequency domain as well as analysis of the experimental data are given. As an object of investigations BiNbO4-based microwave ceramics was taken. Simulations of the hypothetical impedance response of the ceramic system were performed under assumption of the brick-layer model. A strategy for analysis and modelling...
-
Pyrolysis Combined with the Dry Reforming of Waste Plastics as a Potential Method for Resource Recovery—A Review of Process Parameters and Catalysts
Publikacja: Emissions of greenhouse gases and growing amounts of waste plastic are serious environmental threats that need urgent attention. The current methods dedicated to waste plastic recycling are still insufficient and it is necessary to search for new technologies for waste plastic management. The pyrolysis-catalytic dry reforming (PCDR) of waste plastic is a promising pro-environmental way employed for the reduction of both CO2 and...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublikacjaAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
ASSESSMENT OF NATURAL VENTILATION SYSTEM FOR A TYPICAL RESIDENTIAL HOUSE IN POLAND
PublikacjaThe paper presents the research results of field measurements campaign of natural ventilation performance and effectiveness in a residential building. The building is located in the microclimate whose parameters differ significantly in relation to a representative weather station. The measurement system recorded climate parameters and the physical variables characterizing the air flow in the rooms within 14 days of the winter season....
-
Urban space recovery. Landscape-beneficial solutions in new estates built in post-industrial and post-military areas in Bristol, Poznań and Gdańsk
PublikacjaThe limitation of territorial expansion and the implementation of the idea of a compact city are generally accepted paradigms of spatial development of contemporary cities. In consequence, actions are taken to improve the quality of city landscape and revitalise vacant areas. This study approaches the process of city regeneration as transformation and supplementation of the existing urban structure as well as creation of multifunctional, structurally,...
-
Analytical applications of smartphones for agricultural soil analysis
PublikacjaSoil is one of the most important farming resources. Appropriate managing of its quality promotes productive and sustainable agriculture. The valuable farm practice in soil quality managing is based on regular soil analysis with the aim to determine the exact amount of nutrients or other chemical, physical and biological soil properties. Soil analysis usually requires samples collection at desired sampling depth following by samples...
-
Reduced-cost electromagnetic-driven optimisation of antenna structures by means of trust-region gradient-search with sparse Jacobian updates
PublikacjaNumerical optimisation plays more and more important role in the antenna design. Because of lack of design-ready theoretical models, electromagnetic (EM)-simulation-driven adjustment of geometry parameters is a necessary step of the design process. At the same time, traditional parameter sweeping cannot handle complex topologies and large number of design variables. On the other hand, high computational cost of the conventional...
-
Sensorless predictive control of three-phase parallel active filter
PublikacjaThe paper presents the control system of parallel active power filter (APF) with predictive reference current calculation and model based predictive current control. The novel estimator and predictor of grid emf is proposed for AC voltage sensorless operation of APF, regardless of distortion of this voltage. Proposed control system provides control of APF current with high precision and dynamics limited only by filter circuit parameters....
-
Koncepcja i symulacja polowa generatora o zmiennej częstotliwości. Zastosowanie w autonomicznych systemach elektroenergetycznych = Conception and field simulations of a variable frequency generator. Application for autonomous power generation system
PublikacjaStreszczenie angielskie: This paper covers a conception and simulation results for a brushless synchronous generator working with variable speed in an autonomous energy generation system (e.g. airplane power grid, hybrid vehicle, micro-CHP). The papers has two parts: presentation of the generator conception used in modern autonomous energy generation systems, and simulation results using filed model elaborated in Flux2D software....
-
Design, modelling and analysis of a new type of piezoelectric motor. Multicell piezoelectric motor
PublikacjaThis paper describes a new type of piezoelectric motor. The results, obtained in the field of piezoelectric motors, have pointed out that these motors have potentially high possibilities in the future special applications. The research work presents the design, simulations and parameters of the piezoelectric motor with three rotation-mode actuators. The motor is characterized by a high power, relative high speed and torque. The...
-
Employment of passive sampling in monitoring indoor air quality in selected residences in a Tri-city area in Poland
PublikacjaTime-weighted average concentrations of selected volatile compounds were measured in chosen residences in a Tri-City area of Poland by means of passive sampling. The results were compared to those obtained by dynamic technique – sorption tubes filled with Tenax TA sorbent. Results obtained by employing the two techniques were similar. Total volatile organic compound (TVOC) parameters were also determined. An attempt was also...
-
Electrodes array for contactless ECG measurement of a bathing person - a sensitivity analysis
PublikacjaAn applicability of a remote (contactless) electrocardiogram (ECG) measurements in a bathtub is presented in the paper. Possibility of ECG measurements in shallowly filled tube with a water was examined. A bathing person was, both, sitting and lying during experiments performed. The problem became non-trivial when the bathing person was moving in reference to a fixed set of electrodes and located at the longer walls of the bathtub....
-
Assessment and Optimization of Air Monitoring Network for Smart Cities with Multicriteria Decision Analysis
PublikacjaEnvironmental monitoring networks need to be designed in efficient way, to minimize costs and maximize the information granted by their operation. Gathering data from monitoring stations is also the essence of Smart Cities. Agency of Regional Air Quality Monitoring in the Gdańsk Metropolitan Area (pol. ARMAAG) was assessed in terms of its efficiency to obtain variety of information. The results on one-month average concentrations...
-
SELECTED ASPECTS OF THE EVALUATION OF THE QUALITY OF GRAPE WINE
PublikacjaDevelopment of the domestic grape wine market has been presented. The number of grape wine producing entities, acreage, and volume of production over last five years are presented. The composition of red grape wine has been discussed involving health promoting aspects. Two methods of wine quality determination: analytical and sensory meth ods have been described. Physicochemical parameters influencing wine quali ty (acidity, sweetness)...
-
Analytical Estimation of Power Losses in a Dual Active Bridge Converter Controlled with a Single-Phase Shift Switching Scheme
PublikacjaMicro-grid solutions around the world rely on the operation of DC/DC power conver- sion systems. The most commonly used solution for these topologies is the use of a dual active bridge (DAB) converter. Increasing the efficiency and reliability of this system contributes to the improvement in the stability of the entire microgrid. This paper discussed an analytical method of energy efficiency and power loss estimation in a single...
-
LOS and NLOS identification in real indoor environment using deep learning approach
PublikacjaVisibility conditions between antennas, i.e. Line-of-Sight (LOS) and Non-Line-of-Sight (NLOS) can be crucial in the context of indoor localization, for which detecting the NLOS condition and further correcting constant position estimation errors or allocating resources can reduce the negative influence of multipath propagation on wireless communication and positioning. In this paper a deep learning (DL) model to classify LOS/NLOS...
-
An Improved Convolutional Neural Network for Steganalysis in the Scenario of Reuse of the Stego-Key
PublikacjaThe topic of this paper is the use of deep learning techniques, more specifically convolutional neural networks, for steganalysis of digital images. The steganalysis scenario of the repeated use of the stego-key is considered. Firstly, a study of the influence of the depth and width of the convolution layers on the effectiveness of classification was conducted. Next, a study on the influence of depth and width of fully connected...
-
Combination of instrumental and qualitative descriptive analysis for evaluation of selected tonic waters quality features
PublikacjaThe combination of sensory and instrumental analysis was applied for quality assurance of selected tonic waters. The Quantitative Descriptive Analysis (QDA) in terms of fourteen sensory attributes (aroma, astringency, bite, burn, numbing, tongue heaviness, carbonation, mouth coating, sweet taste, sour taste, bitter taste, sweet aftertaste, sour aftertaste, bitter aftertaste) of selected tonic waters was performed by sensory experts....
-
Rapid Variable-Resolution Parameter Tuning of Antenna Structures Using Frequency-Based Regularization and Sparse Sensitivity Updates
PublikacjaGeometry parameter tuning is an inherent part of antenna design process. While most often performed in a local sense, it still entails considerable computational expenses when carried out at the level of full-wave electromagnetic (EM) simulation models. Moreover, the optimization outcome may be impaired if good initial design is not available. This paper proposes a novel approach to fast and improved-reliability gradient-based...
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublikacjaThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
Comparative Analysis of Text Representation Methods Using Classification
PublikacjaIn our work, we review and empirically evaluate five different raw methods of text representation that allow automatic processing of Wikipedia articles. The main contribution of the article—evaluation of approaches to text representation for machine learning tasks—indicates that the text representation is fundamental for achieving good categorization results. The analysis of the representation methods creates a baseline that cannot...
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublikacjaLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Stochastic optimisation algorithm for optimisation of controller parameters for control of dissolved oxygen in wastewater treatment plant
PublikacjaWastewater treatment plants (WWTPs) are very important facilities for mankind. They enable the removal and neutralisation of man-made pollutants. Therefore, it is important for wastewater treatment plants to operate as efficiently as possible so that the level of pollutants in the treated wastewater meets specific requirements. This paper concerns the design of a hierarchical nonlinear adaptive control system for dissolved oxygen...
-
Comparison of tuning procedures based on evolutionary algorithm for multi-region fuzzy-logic PID controller for non-linear plant
PublikacjaThe paper presents a comparison of tuning procedures for a multi-region fuzzy-logic controller used for nonlinear process control. This controller is composed of local PID controllers and fuzzy-logic mechanism that aggregates local control signals. Three off-line tuning procedures are presented. The first one focuses on separate tuning of local PID controllers gains in the case when the parameters of membership functions of fuzzy-logic...
-
Advanced Turbine Cycles with Organic Media
PublikacjaOrganic Rankine Cycle (ORC) power plants have become very popular and have found their applications in systems with renewable sources of energy. So far their overall efficiencies are not very impressive and only for the upper temperature of about 300 °C do they exceed 20%. A drawback of these cycles is the limitation of the cycle upper temperature due to the heat exchanger technology and the materials used. However, it is possible...
-
Verification of the Analytical Traffic Model of a Multidomain IMS/NGN Using the Simulation Model
PublikacjaIn this paper we verify the previously proposed analytical traffic model of a multidomain Next Generation Network (NGN), which is standardized for delivering multimedia services based on the IP Multimedia Subsystem (IMS). For this reason a proper simulation model used, in which not theoretical queuing system models but the operation of real network elements and standardized call scenarios are accurately implemented. Consequently,...