Wyszukiwarka
Filtry
wszystkich: 2900
wybranych: 2290
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: CONCRETE ELEMENTS DIAGNOSTIC
-
Partially prestressed concrete beams with bonded and unbonded strands
PublikacjaThis article relate the tests of partially prestressed concrete beams. There is presented the research programme - geometry of elements, method of loading, the materials and variables. There have been shown preliminary test results of prestressed concrete elements with bonded and unbonded strands, and compared to the test results of R.C. beam.
-
Shear resistance of low height precast concrete lintels
PublikacjaThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Fuctional structure of diagnostic system for wheeled tractors
PublikacjaAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnosis is strongly connected with emission demands and does not concern other important vehicle functions.In...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublikacjaThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part III. Diagnostic and operating tolerances
PublikacjaThe third part of the article presents a method for detecting failures of the automatic engine control system with the aid of an exhaust gas temperature setter, specially designed and machined for this purpose. It also presents a procedure of identifying the operating tolerances and determining the diagnostic tolerances for the exhaust gas temperature recorded in the naval turbine engine during the start-up and acceleration processes....
-
STRUCTURE AND ALGORITHMS OF A DIAGNOSTIC DEVICE IN A WHEELED TRACTOR
PublikacjaDiagnostic device monitors the tractor’s technical condition and identifies the location of damaged components during operation. The diagnostic device detects and identifies the following types of defects: functional defects (uf) which affect performance, exhaust defects (ue) which increase toxic emissions and fuel consumption, defects that jeopardize driving safety (us), defects that affect engine performance (ud). The key component...
-
Experimental study on ultrasonic monitoring of splitting failure in reinforced concrete
PublikacjaThis paper investigates inspection of reinforced concrete elements sensitive to the splitting failure. The behaviour of a reinforced concrete specimen subjected to a tensile stress is considered. The damage detection procedure is based on the ultrasonic wave propagation technique. The piezoelectric transducers are located on both ends of the specimen and the measurements are taken periodically during the incrementally increased...
-
Badania eksperymentalne i symulacyjne dynamiki modelowego odcinka sieci trakcyjnej
PublikacjaW pracy przedstawiono główne założenia i strukturę opracowanego modelu matematycznego odcinka kolejowej górnej sieci trakcyjnej, opartego na metodzie energetycznej Lagrange’a. W celu wyznaczenia wybranych parametrów modelu, jak również dla oceny stopnia zgodności odwzorowania przez utworzony program symulacyjny stanów statycznych i dynamicznych sieci zbudowano laboratoryjny model odcinka sieci jezdnej z użyciem rzeczywistych jej...
-
Modelling of spirometry - the application for diagnostic purposes
PublikacjaThe process of the tissue oxygen supply is the fundamental process of the human life. The lung functioning consists of three processes: the ventilation, the perfusion and the diffusion. The paper deals with one of these processes which is the ventilation process. The quality of the pulmonary ventilation has a strong influence on the patient's health condition. Numerous limitations are imposed on conditions of the lung quality measurement,...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublikacjaTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublikacjaTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublikacjaPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Usability Techniques Possible to Use in Diagnostic Tools Interface Improvement
PublikacjaThe development of diagnostic tools has caused a rapid increase in the amount of information generated and presented, necessitating the use of computer displays as an interface to data presentation and the use of modern diagnostic tools. The paper presents methods for testing usability that can be used in designing and improving the quality of interfaces of modern diagnostic tools that use communication through graphical user interfaces.
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublikacjaDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
SELECTION OF DIAGNOSTIC FUNCTIONS IN A WHEELED TRACTOR
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
PAH diagnostic ratios for the identification of pollution emission sources
PublikacjaPolycyclic aromatic hydrocarbon (PAH) diagnostic ratios have recently come into common use as a toolfor identifying and assessing pollution emission sources. Some diagnostic ratios are based on parentPAHs, others on the proportions of alkyl-substituted to non-substituted molecules. The ratios areapplicable to PAHs determined in different environmental media: air (gas þ particle phase), water,sediment, soil, as well as biomonitor...
-
Diagnostic Model of Crankshaft Seals
PublikacjaT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublikacjaThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublikacjaAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
Trace Elements in Aquatic Environments
PublikacjaA trace element is defined as a chemical element whose the average concentration is less than 100 ppm (mg/kg, mg/L – in the case of a water matrix). In aquatic environments the concentrations of trace elements are usually at the level of picomoles per liter and lower. This causes extreme analytical problems, especially in situations where low content is in the range of background levels. Taking into account the role of trace elements...
-
An application of simulation model of fuel consumption in diagnostic system of wheeled tractors
PublikacjaAn application of computer controlled fuel injection systems in vehicle engines and growing demands concerning toxic substances emission and fuel consumption was a main reason for OBD (On Board Diagnosis) development. In spite of a great technological development, only some tractors are equipped in diagnostic systems. On board diagnostic is strongly connected with emission demands and does not concern other important vehicle functions. In...
-
Diagnostic Models and Estimators for LDI in Transmission Pipelines
PublikacjaThis article considers and compares four analytical models of the pipeline flow process for leak detection and location tasks. The synthesis of these models is briefly outlined. Next, the methodology for generating data and diagnosing pipes is described, as well as experimental settings, assumptions and implemented scenarios. Finally, the quality of model-based diagnostic estimators has been evaluated for their bias, standard deviations...
-
Identification of diagnostic parameter sensitivity during dynamic processes of a marine engine
PublikacjaChanging some parameters of the engine structure alters the emission of harmful components in the exhaust gas. This applies in particular to the damage of charge exchange system as well as fuel system and engine supercharger. These changes are much greater during the dynamic states and their accompanying transitional processes. The different sensitivity of diagnostic parameters to the same force, coming from the engine structure, but...
-
Diagnostic system of wheeled tractors detecting four defect's categories
PublikacjaIn a classical approach to damage diagnosis, the technical condition of an analyzed machine is identified based on the measured symptoms, such as performance, thermal state or vibration parameters. In wheeled tractor the fundamental importance has monitoring and diagnostics during exploitation concerning technical inspection and fault element localizations. The main functions of a diagnostic system are: monitoring tractor components...
-
Spirometry measurement model - the diagnostic purpose support
Publikacjathe paper presents a new model of respiratory mechanism based on the spirometry measurements. the spirometry test assesses the efficiency of the lung ventilation. the respiratory system functioning is based on the ventilation mechanism. thus the quality of the lung depends on the quality of lung ventilation. modelling of the respiratory system supports a diagnostic process. the model parameter estimates are obtained on the basis...
-
Utilization of the zero unitarization method for the building of a ranking for diagnostic marine engine parameters
PublikacjaChanging some of the parameters of the engine structure affects the emission of harmful components in the exhaust gases This primarily concerns damage in the cargo exchange system as well as in the fuel system and engine boost system. Changes in emissions of harmful compounds are often ambiguous, depending largely on the parameters that shape the combustion process. An additional problem is that often simple but undesired interactions...
-
Concrete mix design using machine learning
PublikacjaDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
New hybrid quadrature schemes for weakly singular kernels applied to isogeometric boundary elements for 3D Stokes flow
PublikacjaThis work proposes four novel hybrid quadrature schemes for the efficient and accurate evaluation of weakly singular boundary integrals (1/r kernel) on arbitrary smooth surfaces. Such integrals appear in boundary element analysis for several partial differential equations including the Stokes equation for viscous flow and the Helmholtz equation for acoustics. The proposed quadrature schemes apply a Duffy transform-based quadrature...
-
Machine Learning Techniques in Concrete Mix Design
PublikacjaConcrete mix design is a complex and multistage process in which we try to find the best composition of ingredients to create good performing concrete. In contemporary literature, as well as in state-of-the-art corporate practice, there are some methods of concrete mix design, from which the most popular are methods derived from The Three Equation Method. One of the most important features of concrete is compressive strength, which...
-
The lethal effect of hydrotechnical concrete on freshwater Bivalvia
PublikacjaMost hydrotechnical buildings under construction demand the concrete mixture to be set directly under water. The main reason for such a procedure is to limit the washing away of the the concrete binding mixture and to increase the efficiency of organisation of work so as to ensure continuity in concreting. The impact on the aquatic environment of recent developments in concrete technology and the use of new components has not yet...
-
Induction motor bearings diagnostic indicators based on MCSA and normalized triple covariance
PublikacjaInduction motors are one of the most widely used electrical machines. Statistics of bearing failures of induction motors indicate, that they constitute more than 40% of induction motor damage. Therefore, bearing diagnosis is so important for trouble-free work of induction motors. The most common methods of bearing diagnosis are based on vibration signal analysis. The main disadvantage of those methods is the need for physical access...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublikacjaThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Size effect in concrete under splitting tension
PublikacjaThe size effect is a fundamental phenomenon in concrete materials. It denotes that both the nominal structural strength and material ductility always decrease with increasing element size under tension. In the paper splitting tensile tests on cylindrical concrete specimens with the different diameter were carried out. Two types of the loading strip (plywood board and steel cylinder) were used. The concrete strength and ductility...
-
Calculations of labyrinth seals with and without diagnostic extraction in fluid-flow machines
PublikacjaLabyrinth seals are essential components of steam turbine unit constructions. Two types of labyrinth seals can be named, the first of which is the seal without diagnostic steam extraction, and the second – with extraction. The distribution of flow parameters along the packing is affected remarkably by the average seal clearance. The presence of diagnostic extraction leads to the equation system which is determinable and can be...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublikacjaThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublikacjaThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Induction Motor Bearings Diagnostic Using MCSA and Normalized Tripple Covariance
PublikacjaDiagnosis of induction motors, conducted remotely by measuring and analyzing the supply current is attractive with the lack of access to the engine. So far there is no solution, based on analysis of current, the credibility of which allow use in industry. Statistics of IM bearing failures of induction motors indicate, that they constitute more than 40% of IM damage, therefore bearing diagnosis is so important. The article provides...
-
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublikacjaIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
Alternative diagnostic method applied on marine diesel engines having limited monitoring susceptibility
PublikacjaThe paper presents a method of technical state evaluation of working spaces of a marine diesel engine at the limited control susceptibility. The method foresees making a diagnosis of the engine's working spaces on the basis of measurements of the exhaust gas pressure in the channels connecting engine cylinders with the turbocharger's turbine. Diagnostic measurements are carried out at representative (comparative) steady loads depending...
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublikacjaThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublikacjaThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Experimental verification of visual method for measuring displacements of contact line elements
PublikacjaThe increase of rail vehicles speed, as well as the increase of their power, puts high demands on the power delivery system for traction vehicles The most critical point in the vehicle's power supply circuit is the contact between the current collector and contact wires. Ensuring a reliable co-operation of the current collector and contact line, requires technical development...
-
Non-destructive Testing of Wooden Elements
PublikacjaExamining the condition of wooden elements is crucial from the perspective of proper structure performance. If the deterioration in the internal wood condition, which displays no symptoms visible from the outside, is detected, the further spread of the deterioration can be prevented. Test results often point to the necessity of conducting repairs and, renovations, replacing the structure of wooden beams, or even substituting a...