Wyszukiwarka
Filtry
wszystkich: 1893
wybranych: 1645
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: OPTICAL FIBRE COATINGS
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Ultrasonic-assisted Electrodeposition of Cu-Sn-TiO2 Nanocomposite Coatings with Enhanced Antibacterial Activity
PublikacjaCopper-based coatings are known for their high antibacterial activity. In this study, nanocomposite Cu–Sn–TiO2 coatings were obtained by electrodeposition from an oxalic acid bath additionally containing 4 g/dm3 TiO2 with mechanical and ultrasonic agitation. Ultrasound treatment was performed at 26 kHz frequency and 32 W/dm3 power. The influence of agitation mode and the current load on the inclusion and distribution of the TiO2...
-
Functionalization of graphene oxide coatings with phosphorus atoms and their corrosion resistance in sodium chloride environment
PublikacjaIn this work, we compared corrosion resistance of graphene oxide, and phosphorus functionalized reduced graphene oxide coatings obtained as a result of electrophoretic deposition on the copper substrate. Doping graphene oxide with phosphorus atoms was performed by a hydrothermal method in the presence of different amounts of phosphoric acid. Structural studies confirmed the insertion of phosphorus atoms into the graphene oxide...
-
Optical rotation in the lithium triborate nonlinear crystal
PublikacjaA dual-wavelength polarimetric technique at 633 and 661 nm has been used for the characterization of a nonlinear lithium triborate (LiB3O5) nonenantiomorphous biaxial crystal. The mismatch of the crystallographic and optical coordinate systems was taken into account. The optical rotatory power for light propagation along one of the optical axes is ρ = 7.06° mm−1. The gyration tensor component along the bisector between the x and...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Effect of Functionalization of Reduced Graphene Oxide Coatings with Nitrogen and Sulfur Groups on Their Anti-Corrosion Properties
PublikacjaElectrophoretic production of anticorrosion carbonaceous coatings on copper could be successfully performed by anodic oxidation of negatively charged graphene platelets suspended in an aqueous solution. The various platelets were synthesized by Hummer’s method followed by a hydrothermal reduction in the presence of NH4SCN which was expected to substitute some parts of graphene structure with nitrogen and sulfur groups. X-ray photoelectron...
-
Spectroscopic investigation of Tb(tmhd)3 - Eu(tmhd)3 co-doped poly(methyl methacrylate) fibre
Publikacja -
RSVP-TE as a reservation protocol for optical networks
PublikacjaIn this paper, we consider the reservation of optical resources problem. We implement extensions for RSVP-TE (Resource ReSerVation Protocol with Traffic Engineering Extension) to achieve the new functionality for optical resources reservation. Based on ASON/GMPLS architecture we examine an open source implementation KOM RSVP-Engine and extend its functionality according to ITU-T and IETF recommendations. The transport plane consists...
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublikacjaTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
Enhancing electrochemical properties of an ITO-coated lossy-mode resonance optical fiber sensor by electrodeposition of PEDOT:PSS
PublikacjaA sensor working in multiple domains may offer enhanced information about the properties of an investigated analyte, including those containing biological species. It has already been shown that a dual-domain sensing capability, i.e., in optical and electrochemical domains, can be offered by lossy-mode resonance (LMR) sensors based on indium-tin-oxide (ITO) thin film. The spectral response of the LMR sensors depends on the refractive...
-
Thermal boundary conditions to simulate friction layers and coatings at sliding contacts
PublikacjaA brief review of the thermal boundary conditions specified at sliding interfaces was performed. New thermal boundary conditions were derived aimed at solving problems of sliding with account of surface layers representing friction layers and tribological coatings. Based on the assumption of linear temperature distributions in the surface layers, the proposed conditions enable one to simplify simulations by eliminating the surface...
-
Effect of environmental temperature variations on protective properties of organic coatings
Publikacja -
Antimicrobial properties of protective coatings produced by plasma spraying technique
Publikacja -
Local properties of organic coatings close to glass transition temperature
PublikacjaAcrylic coating applied on copper substrate has been investigated at different temperatures starting from the ambient one up to the level above the glass transition temperature. Its local topographic and electric properties have been examined with the atomic force microscopy (AFM) based approach including dc current mapping and local impedance spectroscopy. The local findings have been compared with the information from global...
-
Effect of environmental temperature variations on protective properties of organic coatings
PublikacjaW oparciu o model rozwoju naprężeń oraz niszczenia kumulatywnego przedyskutowano wpływ zmiennych temperatur środowiska na mechaniczną spójność i własności ochronne systemów powłokowych. Badano wpływ cykli temperaturowych pomiędzy 20 i 55 st. C oraz między -20 i 20 st. C na trwałość różnych powłokowych systemów malarskich na stali. Stosując technikę spektroskopii impedancyjnej monitorowano zmiany parametrów powłok poddanych cyklom...
-
UV Curable Coatings Based on Urethane Acrylates Containing Eugenol and Evaluation of Their Antimicrobial Activity
Publikacja -
Thermal Barrier Coatings for High-Temperature Performance of Nickel-Based Superalloys: A Synthetic Review
Publikacja -
Multilayer coatings based on cerium oxide and manganese cobaltite spinel for Crofer22APU SOC interconnects
PublikacjaThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
The Chemical and Biological Properties of Nanohydroxyapatite Coatings with Antibacterial Nanometals, Obtained in the Electrophoretic Process on the Ti13Zr13Nb Alloy
PublikacjaThe risk of an early inflammation after implantation surgery of titanium implants has caused the development of different antimicrobial measures. The present research is aimed at characterizing the effects of nanosilver and nanocopper dispersed in the nanohydroxyapatite coatings, deposited on the Ti13Zr13Nb alloy, and on the chemical and biological properties of the coatings.The one-stage deposition process was performed by the...
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublikacjaMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
Tailoring the optical parameters of optical fiber interferometer with dedicated boron-doped nanocrystalline diamond thin film
PublikacjaOptical fiber interferometer using nanocrystalline boron-doped diamond film was investigated. The diamond films were deposited on glass plates using a Microwave Plasma-Enhanced Chemical Vapour Deposition (μPE CVD) sys-tem. The growth time was 3h, with boron doping level of 10 000 ppm producing films (B-NCD-10) of thickness ~ 200 nm. The presence of boron atoms in the diamond film is evident in Raman spectrum as peaks at 1212 cm-1...
-
1D portable optical coherence tomography system
Publikacja—Imaging methods are an expanding branch of technology, which involves data acquisition and analysis of images for research and diagnostics. This paper has been devoted to the description of the optical design for a one-dimensional, portable optical coherence tomography (OCT) system. The Mach-Zehnder interferometer has been designed in the presented study. The description of the construction and applied hardware solutions have...
-
The Optical Transport Network Control Based on SDN Architecture
PublikacjaThe aim of this publication is to present research results on the usability of the Software-Defined Networking concept to control transport networks. For this purpose, an easy-to-use connection scheduler was developed capable of controlling connections in optical transport networks. The authors would like to present this solution and details of constructed SDN architecture implemented for modern optical transport solutions based...
-
The Morphology, Structure, Mechanical Properties and Biocompatibility of Nanotubular Titania Coatings before and after Autoclaving Process
PublikacjaThe autoclaving process is one of the sterilization procedures of implantable devices. Therefore, it is important to assess the impact of hot steam at high pressure on the morphology, structure, and properties of implants modified by nanocomposite coatings. In our works, we focused on studies on amorphous titania nanotubes produced by titanium alloy (Ti6Al4V) electrochemical oxidation in the potential range 5–60 V. Half of the...
-
Optical materials for organic light emitting diodes
PublikacjaW pracy dokonano przeglądu materiałów stosowanych w organicznych diodach elektroluminescencyjnych.
-
Use of optical skin phantoms for calibration of dermatological lasers
PublikacjaA wide range of dermatological diseases can be efficiently treated using laser heating. Nevertheless, before the new laser is introduced into clinical practice, its parameters and ability to interact with human skin have to be carefully examined. In order to do that optical skin phantoms can be used. Such phantoms closely imitate the scattering and absorption properties of real human skin tissue along with its thermal properties,...
-
Electrophoretic Deposition of Chitosan/Eudragit E 100/AgNPs Coatings for Controlled Release of Antibacterial Substance
PublikacjaThe development of bacterial infection of the tissues surrounding an implant is one of the leading causes of implant surgery failure. In order to prevent the deposition of bacteria on the implant surface and the formation of biofilm, coatings that exhibit antibacterial properties are manufactured. However, the problem is the controlled release of the therapeutic substance from the coating over the extended life of the implant [1],...
-
Research of chitosan coatings deposited by electrophoretic deposition method at various voltage and time parameters
PublikacjaThe aim of this research is to estimate the electrophoretic deposition main parameters, such as voltage and time duration, that will provide optimal characteristics of the surface layer. Chitosan coatings were synthesized on biomedical Ti13Zr13Nb alloys at 20 V and 30 V and with deposit times of 2min, 5 min, 10 min, and 15 min. Evaluation of the coating was performed by using Scanning Electron Microscope (SEM), Energy-Dispersive...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublikacjaTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Biological and antibacterial properties of chitosan-based coatings with AgNPs and CuNPs obtained on oxidized Ti13Zr13Nb titanium alloy
PublikacjaDespite numerous studies, the antibacterial efficiency and cytotoxicity of chitosan-based coatings with nanometals need further studies. The purpose of this research was to determine the biological properties of chitosan coatings implemented with either silver nanoparticles (AgNPs) or copper nanoparticles (CuNPs), that were electrophoretically deposited on electrochemically oxidized Ti13Zr13Nb alloy. The SEM tests were used to...
-
High temperature corrosion of evaporator tubes with thermal sprayed coatings
PublikacjaDegradation examinations of outer surface of low-emission steam boiler evaporator tubes are presented in the paper. Metallographic evaluation of scale morphology, its micro sites chemical composition analysis and distribution of elements on cross sections have been performed. Water-wall tubes were exposed in steam boiler for up to two years period. Common tubes made of 16Mo3 steel suffered sulphide and molten salts corrosions....
-
Properties of chitosan/CuNPs coatings electrophoretically deposited on TiO2 nanotubular oxide layer of Ti13Zr13Nb alloy
PublikacjaCoatings based on chitosan/CuNPs (chit/CuNPs) were obtained by a one-step electrophoretic deposition (EPD) on nanotubular oxide layer of Ti13Zr13Nb alloy. The deposition was carried out for 1 min applying voltages of 10 and 20 V with and without the addition of dispersing agent (Polysorbate 20) to the suspension. The coatings obtained for the lower voltage were more uniform than for the higher voltage. By adding a dispersing agent,...
-
Diamond-based protective layer for optical biosensors
PublikacjaOptical biosensors have become a powerful alternative to the conventional ways of measurement owing to their great properties, such as high sensitivity, high dynamic range, cost effectiveness and small size. Choice of an optical biosensor's materials is an important factor and impacts the quality of the obtained spectra. Examined biological objects are placed on a cover layer which may react with samples in a chemical, biological...
-
Prediction of fracture toughness in fibre-reinforced concrete, mortar, and rocks using various Machine learning techniques
PublikacjaMachine Learning (ML) method is widely used in engineering applications such as fracture mechanics. In this study, twenty different ML algorithms were employed and compared for the prediction of the fracture toughness and fracture load in modes I, II, and mixed-mode (I-II) of various materials, including fibre-reinforced concrete, cement mortar, sandstone, white travertine, marble, and granite. A set of 401 specimens of “Brazilian...
-
Aluminium Profile Reinforced with Carbon Fibre: Numerical Analysis
Publikacja -
Modification of cement-ash composites with steel fibre addition
PublikacjaPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Effect of MAO coatings on cavitation erosion and tribological properties of 5056 and 7075 aluminum alloys
PublikacjaTwo ceramic coatings have been applied on 5056 and 7075 aluminum alloy by microarc oxidation (MAO) technology. The mass losses, surface morphologies and the phase constituents of the MAO coatings before and after cavitation tests were examined by means of digital scales, scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. In order to assess the impact of the mechanical properties of the surface layer on...
-
Recent advances on spinel-based protective coatings for solid oxide cell metallic interconnects produced by electrophoretic deposition
PublikacjaThe application of ceramic protective coatings to the metallic interconnects in solid oxide cells (SOCs) is a viable and effective method to limit interconnect degradation issues. This featured letter provides a critical overview of the main outcomes of current research on the use of the electrophoretic deposition (EPD) technique to produce protective coatings for SOC metallic interconnects, specifically focusing on different approaches...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublikacjaThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
PublikacjaThe Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a...
-
Polarization-dependent optical absorption in phosphorene flakes
PublikacjaThe interest of 2D materials is constantly increasing because of their very attractive mechanical, electrical and optical parameters. They have been used in many applications, e.g. photodetectors, sensors, modulators, insulators. One of the recently discovered 2D materials is phosphorene. In contrast to graphene, phosphorene has a direct bandgap tuned by numbers of layers in the 2D structure. The phosphorene flakes are strongly...
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublikacjaIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Gold nanoparticles evaluation using functional optical coherence tomography
PublikacjaThe main object of this research was to assess the ability to characterize the gold nanoparticles using optical modalities like optical coherence tomography. Since the nanoparticles, especially gold one, have been very attractive for medical diagnosis and treatment the amount of research activities have been growing rapidly. The nanoparticles designed for different applications like contrast agents or drugs delivery change the...
-
Nanoparticles displacement analysis using optical coherence tomography
PublikacjaOptical coherence tomography (OCT) is a versatile optical method for cross-sectional and 3D imaging of biological and non-biological objects. Here we are going to present the application of polarization sensitive spectroscopic OCT system (PS-SOCT) for quantitative measurements of materials containing nanoparticles. The PS-SOCT combines the polarization sensitive analysis with time-frequency analysis. In this contribution the benefits...
-
Fe-modified Mn2CuO4 spinel oxides: coatings based on abundant elements for solid oxide cell interconnects
PublikacjaThe current state of the art steel interconnect coating materials are based on critical raw material - Co-oxide spinels. Replacing Co-oxide spinels with alternative, abundant materials can reduce the dependence on the critical raw materials. Cobalt-free coatings with the general formula Mn2-xCuFexO4, where x = 0, 0.1, 0.3, were electrophoretically deposited on a ferritic stainless-steel support and evaluated. Prior to deposition,...
-
QoS Resource Reservation Mechanisms for Switched Optical Networks
PublikacjaThe paper regards the problem of resource reservation mechanisms for Quality of Service support in switched optical networks. The authors propose modifications and extensions for resources reservation strategy algorithms with resources pools, link capacity threshold and adaptive advance reservation approach. They examine proposed solutions in Automatically Switched Optical Network with Generalized Multi-Protocol Label Switching...
-
Ceria Based Protective Coatings for Steel Interconnects Prepared by Spray Pyrolysis
PublikacjaStainless steels can be used in solid oxide fuel/electrolysis stacks as interconnects. For successful long term operation they require protective coatings, that lower the corrosion rate and block chemical reactions between the interconnect and adjacent layers of the oxygen or the hydrogen electrode. One of the promising coating materials for the hydrogen side is ceria. Using standard sintering techniques, ceria sinters at around...
-
Optical properties of daylight curable resin doped with nanodiamond powder
PublikacjaIn this paper a new material for 3D printing was elaborated on. Since diamond has very good optical properties, an idea occurred to us to apply it in 3D printing process. A mixture of nanodiamond powder and a standard 3D printing resin was created and several printouts have been completed. They have been tested for their abilities to transmit and absorb light in a wide spectrum of wavelengths. It turned out that the nanopowder...
-
Electrophoretically Deposited Chitosan/Eudragit E 100/AgNPs Composite Coatings on Titanium Substrate as a Silver Release System
PublikacjaDue to the possibility of bacterial infections occurring around peri-implant tissues, it is necessary to provide implant coatings that release antibacterial substances. The scientific goal of this paper was to produce by electrophoretic deposition (EPD) a smart, chitosan/Eudragit E 100/silver nanoparticles (chit/EE100/AgNPs) composite coating on the surface of titanium grade 2 using different deposition parameters, such as the...