Filtry
wszystkich: 552
wybranych: 477
Wyniki wyszukiwania dla: W-TIO2
-
Self-Organized Nanotubular Oxide Layers on Ti and Ti Alloys
PublikacjaTo improve bioactivity of titanium and titanium, the implant surface modification by formation of self-organized TiO2 nanotube arrays with electrochemical techniques is presented. The influence of electrolyte composition and deposition parameters during anodization is characterized. The enhancement of phosphates deposition by titanium nanotubular structure is discussed. The calcium phosphate ceramics is shown to be uniformly deposited...
-
Evaluation of cathode materials for electrochemical photocatalyst deposition
PublikacjaElectrochemical deposition of photocatalyst, especially TiO2, onto several cathode materials was investigated and evaluated. The deposited films were characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDX) and electrochemical measurements. Photocatalytic activity was determined by the decomposition of cyclohexane in air by irradiation with ultraviolet light emitting diodes. It was found that...
-
Preparation and photocatalytic activity of B-doped titanium dioxide
PublikacjaOtrzymano TiO2 domieszkowany borem, aktywny w reakcjach fotodegradacji pod wpływem światła widzialnego (λ>400 nm). Fotokatalizatory otrzymano poprzez hydrolizę tytanianu(IV) izopropylu w obecności związków boru lub poprzez ucieranie ST-01 z prekursorami B i następnie kalcynację w temperaturze 450stC. Jako źródło boru zastosowano kwas borowy (0,5 i 10%wag.) lub trietylo ester kwasu borowego (0,5; 1; 5 i 10%wag.). Najwyższą aktywność...
-
The Effect of Titanium Oxyfluoride Morphology on Photocatalytic Activity of Fluorine-Doped Titanium(IV) Oxide
PublikacjaTitanium oxyfluoride (TiOF2) is a metastable product that can be obtained in a fluorine-rich environment. This material can also be a valuable precursor in the synthesis of titanium(IV) oxide (TiO2). However, the effect of TiOF2 morphology on the physicochemical properties of TiO2 has not been studied so far. In this work, single-phase TiOF2 was prepared by a solvothermal method. The as-synthesized samples exhibited a variety of...
-
Measurements of droplet contact angle of nanofluids
PublikacjaPrzedstawiono wyniki pomiarów kąta zwilżania trzech nanocieczy: woda-Al2O3, woda-TiO2 oraz woda-Cu. Koncentracja nanocząstek wynosiła: 0.01%, 0.1% oraz 1%. Pomiary przeprowadzono dla podłoża szklanego, aluminiowego i ze stali nierdzewnej. Kąt zwilżania mierzono za pomocą goniometru, a także na podstawie zdjęć wykonanych za pomocą kamery cyfrowej.
-
Nitrogen dioxide gas-sensing detection with GO modified CuO thin films
PublikacjaGas sensors have been continuously developed over the last few decades for several applications including air quality monitoring, automotive industry and recently for medical use. Gas sensors are usually based on metal oxides (MOXs), such as SnO2, TiO2, ZnO, WO3, CuO. Recently, new materials such as graphene oxide and heterostructures of graphene oxide and metal oxides are utilized for gassensing applications.
-
The geometry of free-standing titania nanotubes as a critical factor controlling their optical and photoelectrochemical performance
PublikacjaTitanium dioxide nanotubes are regarded as one of the most important functional materials and due to their unique electronic properties, chemical stability and photocorrosion resistance, they find applications in, for example, highly efficient photocatalysis or perovskite solar cells. Nevertheless, modification of TiO2 nanotubes is required to overcome their main drawback, i.e. large energy bandgap (>3.2 eV) limiting their ability...
-
Electrodes consisting of PEDOT modified by Prussian Blue analogues deposited onto titania nanotubes – Their highly improved capacitance
PublikacjaIn this work we present the outstanding energy storage of prepared inorganic-organic heterojunction where hydrogenated ordered titania nanotubes (H-TiO2NT) were modified by the hybrid made of poly(3,4-ethylenedioxythiophene) (pEDOT) and iron hexacyanoferrate centres (Fehcf, Prussian Blue). The material TiO2NT/pEDOT:Fechf was obtained electrochemically by means of: anodization, hydrogenation and finally, electropolymerization of...
-
Laser-assisted modification of titanium dioxide nanotubes in a tilted mode as surface modification and patterning strategy
PublikacjaElectrochemical anodization is regarded as a facile and easily scalable fabrication method of titania nanotubes (TiO2NTs). However, due to the extended duration of calcination and further modifications, much faster alternatives are highly required. As a response to growing interest in laser modification of nanotube arrays, a comprehensive investigation of pulsed-laser irradiation and its effect onto TiO2NT properties has been carried out....
-
Band Gap Engineering toward Semimetallic Character of Quinone-Rich Polydopamine
PublikacjaSemiconductor|melanin interfaces have received increasingly more attention in the fields of photocatalysis and applied electrochemistry because of their facile synthesis, unique electrical properties, and strong capability toward photosensitization. In this work, we describe the electropolymerization of quinone-rich polydopamine (PDA) on the surface of hydrogenated TiO2 nanotubes with enhanced photoactivity in the visible spectrum....
-
Anodic titania nanotubes decorated with gold nanoparticles produced by laser-induced dewetting of thin metallic films
PublikacjaHerein, we combine titania layers with gold species in a laser-supported process and report a substantial change of properties of the resulting heterostructures depending on the major processing parameters. Electrodes were fabricated via an anodisation process complemented with calcination to ensure a crystalline phase, and followed by magnetron sputtering of metallic films. The obtained TiO2 nanotubes with deposited thin (5, 10...
-
Aggregation of Rhodamine 6G in titanium dioxide nanolayers and bulk xerogels
PublikacjaNanolayers and bulk xerogels of Rhodamine 6G (Rh6G) in titanium dioxide (Rh6G/TiO2) were prepared using the sol–gel method. The spectroscopic and structural properties of these two types of hybrid matrices were studied as a function of dye concentration. In both cases absorption, fluorescence and time resolved emission spectra show the formation of fluorescent aggregates. The observed stronger changes in characteristics of bulk...
-
Visible-light-induced photocatalysis through surface Plasmon excitation of gold on titania surfaces
PublikacjaPietnascie komercyjnych probek tlenku tytanu(IV) zostalo zmodyfikowanych zlotem za pomoca fotodepozycji oraz scharakteryzowanych. Fotoaktywnosci proszkow Au/TiO2 zostaly przebadane dla fotodegradacji kwasu octowego i 2-propanolu podczas naswietlania promieniowaniem widzialnym oraz ultrafioletowym. Wykazano, ze fotokatalityczne aktywnosci scisle zaleza od wlasciwosci nanoczastek zlota i tlenku tytanu. Analizy spektrum działania...
-
Preparation of platinum modified titanium dioxide nanoparticles with the use of laser ablation in water
PublikacjaWe report on the preparation method of nanocrystalline titanium dioxide modified with platinum by using nanosecond laser ablation in liquid (LAL). Titania in the form of anatase crystals has been prepared in a two-stage process. Initially, irradiation by laser beam of a titanium metal plate fixed in a glass container filled with deionized water was conducted. After that, the ablation process was continued, with the use of a platinum...
-
The influence of polarization of titania nanotubes modified by a hybrid system made of a conducting polymer PEDOT and Prussian Blue redox network on the Raman spectroscopy response and photoelectrochemical properties
PublikacjaIn this work we show the impact of applied potential on network vibrations and photoelectrochemical properties of a composite material containing hydrogenated titania nanotubes and poly (3,4-ethylenedioxythiophene) with iron hexacyanoferrate (H-TiO2/pEDOT:Fehcf) acting as a redox centre. For this purpose, Raman spectroscopy measurements under the working electrode (WE) polarization were carried out, allowing investigation of changes...
-
Titania nanotubes modified by a pyrolyzed metal-organic framework with zero valent iron centers as a photoanode with enhanced photoelectrochemical, photocatalytical activity and high capacitance
PublikacjaThe paper discusses the synthesis, photoelectrochemical and electrochemical behaviour of titania nanotube arrays modified by a pyrolyzed metal-organic framework (MOF). A poly(3,4–ethylenedioxyphene) (PEDOT) matrix with an embedded inorganic network of iron hexacyanoferrate (BP) covering TiO2 nanotubes (TNT) is used as a MOF for the further sintering procedure, resulting in a novel, thin film of carbonaceous wrap supported Fe catalytic...
-
Synthesis and photoelectrochemical behaviour of hydrogenated titania nanotubes modified with conducting polymer infiltrated by redox active network
PublikacjaIn this work, we show preparation of ordered inorganic-organic composite electrode material where hydrogenated titania nanotubes H-TiO2 with tubularly developed surface modified with poly(3,4-ethylenedioxythiophene) matrix permeated by Prussian Blue (PB) inorganic redox network in order to reach highly photoactive heterojunction. The polymer deposition was realized via two subsequent processes covering: i) potentiostatic polymerization...
-
Nanomateriały o właściwościach magnetycznych, fotokatalitycznych, biobójczych
PublikacjaTematyka badawcza pracy doktorskiej obejmuje preparatykę i charakterystykę nanomateriałów o właściwościach magnetycznych, fotokatalitycznych, biobójczych. Celem pracy była preparatyka nanomateriałów na bazie TiO2 oraz ZnFe2O4 oraz zastosowanie nanokompozytów w fotokatalizie heterogenicznej do degradacji ksenobiotyków niepodatnych na rozkład biologiczny i otrzymywania funkcjonalnych materiałów budowlanych. Otrzymane nanokompozyty...
-
Fotokatalityczne uzdatnianie wody basenowej = Photocatalytic treatment of swimming pool water
PublikacjaW uzdatnianiu wody obserwuje się wzrastające znaczenie alternatywnych rozwiązań technologicznych, do których należą metody zaawansowanego utleniania oraz metody fotokatalityczne z zastosowaniem promieniowania ultrafioletowego a także, coraz częściej, promieniowania w zakresie widzialnym (słonecznego). W tym odniesieniu, przedstawiono istotę fotokatalizy w nadfiolecie i w zakresie widzialnym oraz sposoby przygotowania fotokatalizatorów...
-
Electrical properties of hybrid planar diode based on palladium phthalocyanine and titanium dioxide
PublikacjaThis work details experimental studies of a planar diode made of indium tin oxide/titanium dioxide/palladium phthalocyanine/gold. The rectification ratio of current was 105 at 1.5 V. The analysis of the electrical properties of the system was based on small signal complex capacitance spectra measured in the frequency range of 25 Hz-1 MHz at different values of bias. No depletion region at the TiO2/PdPc interface was observed. Forward...
-
Characterization of Bi6Fe2Ti3O18 Ceramics with Impedance Spectroscopy
PublikacjaIn the present research the tool of impedance spectroscopy was utilized to characterize dielectric behavior of Aurivillius-type ceramics of Bi6Fe2Ti3O18 composition fabricated by hot pressing method from the stoichiometric mixture of oxides Bi2O3, TiO2 and Fe2O3. Impedance spectroscopy was applied to characterize dielectric response of bulk, grain boundary, and material/electrode interfaces of the fabricated polycrystalline ceramic...
-
The Influence of Titania Electrode Modification with Lanthanide Ions Containing Thin Layer on the Performance of Dye-Sensitized Solar Cells
PublikacjaThe lanthanide and scandium groups ions (except Pm and Ac) have been used as dopants of TiO2 film in dye-sensitized solar cells. The X-ray diffraction spectra show that the modification has no influence on the structure of the electrode; however, the diffuse reflectance UV-Vis measurements exhibit significant changes in the electronic properties of modified electrodes. The appearance of energy barrier preventing photoexcited electron...
-
INFLUENCE OF SURFACE CURVATURE ON SESSILE DROPLET CONTACT ANGLE OF NANOFLUIDS
PublikacjaThis paper deals with change in contact angle of droplets of three nanofluids, i.e. water-Al2O3, water-TiO2 and water-Cu. Nanoparticles were tested at the concentration of 0.01%, 0.1%, and 1% by weight. Although dispersants were not used to stabilize the suspension, the solutions tested exhibited satisfactory stability. Ultrasonic vibration was used in order to stabilise the dispersion of the nanoparticles. Experimental measurements...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublikacjaThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
In situ spectroelectrochemical and theoretical study on the oxidation of a 4H-imidazole-ruthenium dye adsorbed on nanocrystalline TiO2thin film electrodes
PublikacjaTerpyridine 4H-imidazole-ruthenium(ii) complexes are considered promising candidates for use as sensitizers in dye sensitized solar cells (DSSCs) by displaying broad absorption in the visible range, where the dominant absorption features are due to metal-to-ligand charge transfer (MLCT) transitions. The ruthenium(iii) intermediates resulting from photoinduced MLCT transitions are essential intermediates in the photoredox-cycle...
-
The influence of the Cu2O deposition method on the structure, morphology and photoresponse of the ordered TiO2NTs/Cu2O heterojunction
PublikacjaThe increased interest in highly ordered titania structures exhibiting tubular shape that could be directly formed onto the stable substrate is related with the intensive research on their modification enabling absorption of light within the wide solar spectrum and its further conversion into electric or chemical energy. Among others, formation of uniform 3D heterojunctions based on the TiO2 nanotubes attracts attention since porous...
-
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublikacjaIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Degradation of metamizole sodium
PublikacjaW ostatnich latach notuje się znaczący wzrost konsumpcji leków i suplementów diety. Wiele osób nie zdaje sobie sprawy z niebezpieczeństw jakie niesie za sobą stosowanie leków na własną rękę. Leki przeciwbólowe i przeciwgorączkowe są stosowane w olbrzymich ilościach. Dostają się one do środowiska poprzez oczyszczalnie ścieków, odchody ludzkie i zwierzęce. W celu określenia wpływu tych grup leków na środowisko przeprowadzono badania...
-
Properties of Nasicon-based CO2 sensor with Bi8Nb2O17 reference electrode
PublikacjaGas sensors are useful for the carbon dioxide concentration monitoring in many applications. The major challenge is to develop a potentiometric sensor working without the necessity of a reference gas and without a need of the reference electrode encapsulation. Important issue is a selection of reference electrode material, which should provide stable reference potential. For example as reference electrode material in sensor based...
-
Stability Investigation of the PCM Nanocomposites
PublikacjaEnsuring the stability is a key issue to be solved for the technical application of nanocomposites. In this work, fatty acid P1801 served as base phase change material (PCM)P1801, and its main ingredients are palmitic acid (58%) and stearic acid (38%). Titania (TiO2) and alumina (Al2O3) with mass concentrations of 1% and 5% were selected as nanoparticles, while polyvinylpyrrolidone (PVP) or oleic acid (OA) with mass concentrations...
-
Magnetic field effects in dye-sensitized solar cells controlled by different cell architecture
PublikacjaThe charge recombination and exciton dissociation are generally recognized as the basic electronic processes limiting the efficiency of photovoltaic devices. In this work, we propose a detailed mechanism of photocurrent generation in dye-sensitized solar cells (DSSCs) examined by magnetic field effect (MFE) technique. Here we demonstrate that the magnitude of the MFE on photocurrent in DSSCs can be controlled by the radius and...
-
Fuzzy reasoning system design and assessment of load-bearing endoprostheses and their fabrication processes
PublikacjaZaproponowano piec zastosowan podejscia rozumowania rozmytego do rozwiazania problemów w dziedzinie biomechanikioraz inzynierii biomateriałów. Obejmuja one: (A) oszacowanie maksymalnych naprezen kontaktowych działajacych naendoproteze, (B) zaprojektowanie procesu spiekania dla otrzymania porowatego implantu, (C) opracowanie planu utleniania wcelu otrzymania struktury nanorurkowej na stopach Ti, (D) oraz (E) zaprojektowanie osadzania...
-
Ordered titania nanotubes layer selectively annealed by laser beam for high contrast electrochromic switching
PublikacjaThe phase conversion from amorphous into crystalline one in the selected area of as-anodized titania nanotubes was achieved via laser treatment. The optimized processing parameters enable fast, one-minute crystallization of titania within an area limited by a shadow mask and without any morphology damage of ordered TiO2 tubular film. The laser annealed titania nanotubes could be easily overgrown by a conducting polymer without...
-
Fabrication of Bi6Fe2Ti3O18 Ceramics by Mixed Oxide Method
PublikacjaIn the present study Bi6Fe2Ti3O18 (BFTO) ceramics has been fabricated by solid state reaction from the mixture of simple oxides viz. Bi2O3, TiO2 and Fe2O3. Stoichiometric mixture of the powders was thermally analyzed so parameters of the thermal treatment were determined. The EDS measurements have shown conservation of the chemical composition of the ceramic powder after calcination. Hot-pressing method was used for final densification...
-
Higher harmonics of the intensity modulated Photocurrent/Photovoltage spectroscopy response - a tool for studying photoelectrochemical nonlinearities
PublikacjaIn this work, a higher harmonic analysis (HHA) of the intensity modulated photocurrent/photovoltage (IMPS/IMVS) spectroscopy data is proposed as a potent tool for studying nonlinear phenomena in photoelectrochemical and photovoltaic systems. Analytical solutions of kinetic equations were constructed for cases of single and double resonance accounting for various sources of higher harmonics. These sources correspond to the physical...
-
Peroxymonosulfate-assisted photocatalytic degradation of artificial sweeteners in water
PublikacjaIn the present study, peroxymonosulfate (PMS) activation was proposed for efficient photocatalytic degradation of aspartame, acesulfame, saccharin, and cyclamate - artificial sweeteners frequently present in wastewaters and surface waters worldwide. The TiO2 nanosheets with exposed {0 0 1} facets were synthesised using the fluorine-free lyophilisation technique as a green concept for the synthesis and used for the photodegradation...
-
Experiments on compression ignition engine powered by nano-fuels
PublikacjaThe use of nanoparticles in fuels provides new opportunities for modification of fuel properties, which may affect the operational parameters of engines, in particular the efficiency and fuel consumption. The paper presents comparison of compression ignition engine performance fuelled with neat diesel and nano-diesel. Alumina (Al2O3) was used as nanoparticles. Surface-active substances, including Span 80 surfactant, as well as...
-
Stability investigation of the PCM nanocomposites
PublikacjaIn present study was showed the results of research the stability of nanoPCMs in terms of types and concentrations of surfactant used. For stearic acid has been added PVP or oleic acid in concentrations of 0%, 5% and 10%. Nanoparticles TiO2 and Al-2O3 in concentration of 1% were chosen to be researched in this test. The mixing of nanocomposites has been done in an ultrasonic scrubber in which the samples were placed for 45 mins....
-
Magnetic photocatalysts for water treatment
PublikacjaThe concept of magnetic photocatalysts with separation function requires ferromagnetic material with high magnetic susceptibility to an external magnetic field to enable recycling of composite nanoparticles. Currently, much attention is devoted to functionalization of photocatalyst using MFe2O3, where M =Fe, Zn, Co, Mn. However direct contact between photocatalyst and magnetic iron oxide particles leads to photodissolution of iron...
-
Hybrid electrode materials for fast performance devices
PublikacjaEnergy storage devices such as Electrochemical Double Layer Capacitors and other types of the electrochemical capacitors require chemically stable, non-soluble, electrochemically active electrode materials compatible with appropriate electrolytes. Factors which determine their applicability are derived from so called electrochemical window of electroltes, nature of charge accumulation and their kinetics. On the other hand technological...
-
Nanoparticles displacement analysis using optical coherence tomography
PublikacjaOptical coherence tomography (OCT) is a versatile optical method for cross-sectional and 3D imaging of biological and non-biological objects. Here we are going to present the application of polarization sensitive spectroscopic OCT system (PS-SOCT) for quantitative measurements of materials containing nanoparticles. The PS-SOCT combines the polarization sensitive analysis with time-frequency analysis. In this contribution the benefits...
-
Unraveling a novel microwave strategy to fabricate exposed {001}/{101} facets anatase nanocrystals: Potential for use to the elimination of environmentally toxic metronidazole waste
PublikacjaThis study present a novel microwave strategy to fabricate highly active anatase particles, exposing {101} and {001} facets. Microwave treatment time was shown to determine the growth of crystals in a certain direction. To the best of our knowledge, it is the first report revealing that the contact time of TiO2 crystals with fluorine ions during the microwave process affects the formed morphology, in particular exposed facets ratio....
-
Burnout Investigation of Small Diameter Tubes Immersed in Nanofluids
PublikacjaThis paper deals with research into pool boiling critical heat flux (CHF) of water–Al2O3, water–TiO2 and water–Cu nanofluids on horizontal stainless steel tubes. The experiments were conducted under atmospheric pressure. Nanoparticles were tested at concentrations of 0.001%, 0.01%, 0.1% and 1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Although dispersants were not used to...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublikacjaGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
Nanolayers in Fiber-Optic Biosensing
PublikacjaIn this chapter, fiber-optic sensors based on nanolayers or thin films and their ability to perform biophotonic measurements is presented. In the last decade, fiber-optic sensors have gained popularity as biosensing devices. This has been made possible because of the design and the integration of new materials in fiber-optic technology. Nanolayers and thin films made from various materials such as nanodiamond (NCD), boron-doped...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublikacjaThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Thermal analysis of Magnetohydrodynamics (MHD) Casson fluid with suspended Iron (II, III) oxide-aluminum oxide-titanium dioxide ternary-hybrid nanostructures
PublikacjaThis study is carried out to enhance and analyze the thermal performance of non-Newtonian Casson fluid by immersing Ternary hybrid nanoparticles Fe3O4-Al2O3-TiO2 uniformly. To model the behaviour of such complex phenomena mathematically, a system of complex transport differential equations is developed by utilizing a non-Fourier heat transfer model for energy transport. The non-dimensional system of transport equations involving...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublikacjaThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Effect of ionic liquids on surface and photocatalytic properties of selected semiconducttors
PublikacjaThe main aim of this doctoral dissertation was to explain the role of ionic liquids in shaping the morphology of selected semiconductors, thereby enhancing the photocatalytic activity. In order to achieve this goal, the following research steps were taken: (i) developing synthesis methods of selected semiconductors, with particular emphasis on the electrochemical oxidation method; (ii) understanding the influence of the selected...
-
Advanced operating methods
PublikacjaSelected operating methods of resistive gas sensors were presented. The methods utilize flicker noise (1/f noise), which gives additional information about ambient gas when compared with the recorded changes of DC resistance only. Methods of flicker noise measurements were outlined. Recently developed prototype gas sensors comprising golden nanoparticle functionalized with organic ligands can generate intense flicker noise induced...