Filtry
wszystkich: 172
wybranych: 164
Filtry wybranego katalogu
Wyniki wyszukiwania dla: pressure drop
-
The influence of pressure drop on the working volume of a hydraulic motor
PublikacjaReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublikacjaAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Methods of Determining Pressure Drop in Internal Channels of a Hydraulic Motor
PublikacjaIn this paper, new methods for determining the pressure drop in internal channels of a hydraulic motor are proposed and described. Mathematical models of pressure losses in internal channels have also been described. Experimental tests of the satellite motor were carried out according to one of the proposed methods. The tests were carried out for two liquids, i.e., water and mineral oil. Experimental studies have shown that at...
-
Experimental Investigations On The Momentum Pressure Drop During Flow Boiling Of R134a
PublikacjaThe article presents experimental investigations of the pressure drop during twophase flow. Experiments were performed for both adiabatic and heated flow of R134a. Obtained flow patterns were compared with the literature. Obtained data is used to validate momentum pressure drop predictions, a set of graphs showing comparisons, for a representative set of experimental conditions, of the two-phase frictional pressure gradients for...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Pressure drop related to flow maldistribution in a model minichannel plate heat exchanger
PublikacjaThe paper describes the issues related to the pressure drop that accompanies the phenomenon of maldistribution of working fluid between the channels of a model minichannel plate heat exchanger. The research concerns a single exchanger's plate containing 51 (in every geometry) parallel rectangular minichannels of hydraulic diameters 461 µm, 571 µm, 750 µm and 823 µm. In addition, the more complex geometry has been investigated,...
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublikacjaIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
Heat transfer and pressure drop characteristics of the silicone-based plate heat exchanger
PublikacjaThe paper presents an experimental investigation of a silicone based heat exchanger, with passive heat transfer intensification by means of surface enhancement. The main objective of this paper was to experimentally investigate the performance of a heat exchanger module with the enhanced surface. Heat transfer in the test section has been examined and described with precise measurements of thermal and flow conditions. Reported...
-
The Methodology for Determining the Theoretical Based on the Characteristics of Effective Absorbency Versus Pressure Drop in the Motor
PublikacjaThis article describes a method for determining the theoretical and actual working volume of a hydraulic motor. It has been shown that the actual working volume of the motor is the sum of the theoretical working volume and the additional volume that depends on the pressure drop in the working chambers of the motor. It was also shown that the volumetric losses in the hydraulic motor are not only a function of the pressure drop in...
-
Determination of pressure drop in flow condensation of HFE7000 in minichannels with account of non-adiabatic effects
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation, however such method has yet to be suggested. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublikacjaConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublikacjaFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Experimental validation of pressure drop models during flow boiling of R134a – effect of flow acceleration and entrainment
PublikacjaA crucial step to assure proficient work of power and process apparatus is their proper design. A wide array of those devices operates within boiling or condensation of the working fluid to benefit from high heat transfer rates. Two-phase flows are associated with high heat transfer coefficients because of the latent heat of evaporation and high turbulence level between the liquid and the solid surface. Predicting heat transfer...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Heat transfer and pressure drop during flow boiling of refrigerant/oil mixture inside smooth tube
PublikacjaW pracy przedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czystych oraz zaolejonych czynników chłodniczych (R22, R134a, R407C) wrzących w poziomej stalowej rurce.
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublikacjaThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. On the heat transfer surface of heat exchanger the metallic porous layer was created. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Experimental and comparative study on the two-phase pressure drop of air-water mixture in U-bend and straight pipe annuli
PublikacjaIn this paper, the experimental and theoretical analysis of pressure drop in singlephase and two phase-flow were presented for straight and U-bend smooth tube annulus and tube annulus with wire coil insert. Experiments for various boundary conditions were performed. In case of U-tube and straight tube with and without turbulator, tests were made for the water-water and air-water systems. The study covered a wide measuring range,...
-
Heat transfer and pressure drop during flow boiling of pure efrigerants and refrigerant/oil mixtures in tube with porous coating
PublikacjaW pracy przedstawiono wpływ powłoki porowatej na średni współczynnik przejmowania ciepła oraz opory przepływu podczas wrzenia wybranych czynników chłodniczych wewnątrz poziomych rurek. Badania przeprowadzono dla techniczne czystych czynników chłodniczychR22, R134a i R407C oraz ich mieszanin z olejem poliestrowym 1% i 5% wrzących w rurkach wykonanych ze stali nierdzewnej, o wewnętrznej powierzchni gładkiej oraz z metaliczną powłoką...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Response to the queries raised by Dr M.M. Awad in a letter to editor comments on “Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels”
Publikacja.
-
Detailed experimental investigations on frictional pressure drop of R134a during flow boiling in 5 mm diameter channel: The influence of acceleration pressure drop component =Études expérimentales détaillées sur la chute de pression frictionnelle du R134a lors de l'ébullition en écoulement dans un canal de 5 mm de diamètre : influence de la composante d'accélération de la chute de pression
PublikacjaThis article presents detailed two-phase diabatic pressure drop data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg m−2 s−1. The obtained data are used as a validation of the void fraction literature models, a set of graphs shows comparisons, for a representative set of experimental conditions,...
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Sensitive Determination of Cd in Small-Volume Samples by Miniaturized Liquid Drop Anode Atmospheric Pressure Glow Discharge Optical Emission Spectrometry
Publikacja -
A miniaturized atmospheric pressure glow microdischarge system generated in contact with a hanging drop electrode – a new approach to spectrochemical analysis of liquid microsamples
Publikacja -
Hanging drop cathode-atmospheric pressure glow discharge as a new method of sample introduction for inductively coupled plasma-optical emission spectrometry
Publikacja -
Pressure losses and power balance in the unloaded satellite pump
PublikacjaThis paper presents the results of laboratory research the pressure drop in the internal channels of unloaded satellite pump pumping tap water. Also shows the characteristics of the increase of pressure in the working chamber of the pump. It has been shown that after reaching cavitation, increase pump speed will increase in torque. This is the moment of inertia caused by the increase of the operating mechanism and the liquid contained...
-
PRESSURE LOSSES AND POWER BALANCE IN THE UNLOADED SATELLITE PUMP
PublikacjaThis paper presents the results of laboratory research the pressure drop in the internal channels of unloaded satellite pump pumping tap water. Also shows the characteristics of the increase of pressure in the working chamber of the pump. It has been shown that after reaching cavitation, increase pump speed will increase in torque. This is the moment of inertia caused by the increase of the operating mechanism and the liquid contained...
-
The Influence of Water and Mineral Oil on Pressure Losses in Hydraulic Motor
PublikacjaIn this paper, pressure losses in hydraulic motor supplied with water and mineral oil (two liquids that have significantly different viscosity and lubricating properties) are described and compared. The experimental tests were conducted using a hydraulic satellite motor that is dedicated to working with different liquids, including water. The methodology of measuring the pressure drop in internal channels of this motor is also...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublikacjaA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublikacjaThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Experimental investigation of forced convection of water-Al2O3 nanofluids inside horizontal tubes,
PublikacjaIn this paper, forced convection of water–Al2O3 nanofluids inside horizontal copper tube is studied experimentally. Experiments were conducted for three, i.e. 0.1%, 1% and 5% nanoparticle mass concentrations under transition and turbulent flow regimes. Average heat transfer coefficients and pressure drop values were determined and compared to distilled water. Enhancement of heat transfer for lower nanoparticle concentration and...
-
Experimental investigation of forced convection of water/EGAl2O3 nanofluids inside horizontal tube
PublikacjaIn this paper, forced convection of water/EG-Al2O3 nanofluids inside horizontal stainless steel tube is studied experimentally. As base fluid served water/EG mixture of two ratios (60:50 and 50:50). Nanoparticle mass concentrations was 0.1% or and 1%. Transition and turbulent flow regimes were tested. Average heat transfer coefficient and pressure drop values were determined for nanofluids and compared to base fluids. Deterioration...
-
Insights Into Hydrodynamics of Spinning Fluids Reactor
PublikacjaSpinning fluids reactor (SFR) is one of the most efficient gas-liquid contacting system with high potential of application in many fields. The unique solution of SFR is the contacting of two spinning fluids which generated centrifugal force. The aim of this study was to investigate the pressure field distribution on the inner surface of reactors dispersing element. Obtained results confirm the high heterogeneity of the field pressure...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublikacjaThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
The new concept of capillary forces aided evaporator for application in domestic organic rankine cycle
PublikacjaThis paper presents studies on the possibility of applying capillary forces induced in the porous structure to a modern design of evaporator. The potential application of such heat exchanger is for example an evaporator of the domestic micro combined heat and power (CHP) unit. One of the problems in the micro-CHP is excessive demand for pumping power. The proposed design helps in overcoming that issue. In the evaporator outlined...
-
Determination of the Theoretical and Actual Working Volume of a Hydraulic Motor—Part II (The Method Based on the Characteristics of Effective Absorbency of the Motor)
Publikacja: In this article, the second method of determination of the theoretical and actual working volume of a hydraulic motor is described. The proposed new method is based on the characteristics of effective absorbency of the motor. The effective absorbency has been defined as the ratio of flow rate in a motor to the rotational speed of the motor’s shaft. It has been shown that the effective absorbency is a nonlinear function of the...
-
Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy–Weisbach equation and the issue of friction factor
PublikacjaIn this article, we consider the modelling of stationary incompressible and isothermal one-dimensional fluid flow through a long pipeline. The approximation of the average pressure in the developed model by the arithmetic mean of inlet and outlet pressures leads to the known empirical Darcy–Weisbach equation. Most importantly, we also present another improved approach that is more accurate because the average pressure is estimated...
-
The protocol for using elastic wall model in modeling blood flow within human artery
PublikacjaMedical diagnostic tools will play a major role in the future for an effective patient treatment and reduction their mortality, related to the cardiovascular system diseases (CVDs). There is an urgent need for developing diagnostic procedure to be robust, reliable, accurate and efficient, in the framework of a paradigm shift. Application of numerical techniques is seen as a perspective tool for such purpose. Nevertheless, existing...
-
Selected studies of flow maldistribution in a minichannel plate heat exchanger
PublikacjaAnalysis of the state of-the-art in research of minichannel heat exchangers, especially on the topic of flow maldistribution in multiple channels, has been accomplished. Studies on minichannel plate heat exchanger with 51 parallel minichannels with four hydraulic diameters, i.e., 461 μm, 574 μm, 667 μm, and 750 μm have been presented. Flow at the instance of filling the microchannel with water at low flow rates has been visualized. The...
-
ANALYSIS OF ROLLING RESISTANCE OF TIRES WITH RUN FLAT INSERT APPLYING DRUM METHOD AND RADIAL CHARACTERISTIC
PublikacjaThis paper presents analysis of rolling resistance of tires with RUN FLAT insert applying drum method and radial characteristic. The conducted studies indicated changes in operational properties of wheel, occurring as a result of inflation pressure drop in the wheel. As regards radial elasticity, such changes result in significant drop of radial rigidity and increase of static deflection and increase of tire rolling resistance....
-
Impact of slow breathing on the blood pressure and subarachnoid space width oscillations in humans
PublikacjaThe aim of the study was to assess cardiac and respiratory blood pressure (BP) and subarachnoid space (SAS) width oscillations during the resting state for slow and fast breathing and breathing against inspiratory resistance. Experiments were performed on a group of 20 healthy volunteers (8 males and 12 females; age 25.3 ± 7.9 years; BMI = 22.1 ± 3.2 kg/m2). BP and heart rate (HR) were measured using continuous finger-pulse photoplethysmography....
-
A simple approach to heat exchanger sizing optimisation by means of entrophy generation minimisation
PublikacjaIn the paper an attempt is presented to find the method of optimization of microtube diameter with respect to optimal thermal-hydraulic conditions in the single-phase shell-and-tube heat exchangers. The approach is based on consideration of pumping power at the condition of maximum heat transfer by the heat exchanger tube system. In the optimization method the tube diameter is first specified and then appropriate calculations are...
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Thermal and economic investigation of straight and U-bend double tube heat exchanger with coiled wire turbulator
PublikacjaExperimental research has been carried out for four individual heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend and U-bend with turbulator. Tests were made for the water-water system. The study covered a wide measuring range, i.e., Re = 800–9000 – on the shell side, for a constant cold water temperature of 9 ◦C and hot water of 50 ◦C. The heat exchangers were made from copper tubes with...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Comparison of Mathematical Models of Torque Transmitted by Multi-disc Wet Clutch with Experimental Results
PublikacjaIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Experimental Study of Flow Rate in Hydraulic Satellite Motor with the Rotating Case at a Low Constant Rotational Speed
PublikacjaIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublikacjaConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Experimental and Computational Fluid Dynamics Studies on Straight and U-Bend Double Tube Heat Exchangers with Active and Passive Enhancement Methods
PublikacjaIn this work, the authors wanted to demonstrate the possibility to increase the heat transfer efficiency by using simple wire coil inserts to create turbulent flow in the boundary layer as well as air blowing into the annulus of the pipe. Experimental investigations were carried out for four heat exchanger constructions, i.e., plain double tube, turbulized double tube, plain U-bend double tube, U-tube with turbulator, plain double...
-
High Performance Tubular Heat Exchanger with Minijet Heat Transfer Enhancement
PublikacjaIn the paper, the original cylindrical heat exchanger with minijets (MJHE) was introduced. The systematic experimental analysis of the prototype heat exchanger was described with special attention paid to such parameters as the heat transfer effectiveness, heat transfer rates, overall heat transfer coefficients, and pressure drop. The heat transfer coefficients were determined based on Wilson plot method, the most suitable approach...
-
NUMERICAL SIMULATIONS OF GAP FLOW ABOVE ROTATING DISK
PublikacjaA rotating disk can be considered a basic configuration for the investigati ons of the impact of various conditions on the flow through the clearance between the s hrouded turbine blade and the casing. Numerical calculations using Fine/Turbo Numeca were conducted to examine the influence of the rotational velocity and the pressure differ ence across the disk on the flow conditions, especially the mass flow through the clearance....
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublikacjaUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems utilizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for cogenerative...
-
Dynamic model of nuclear power plant turbine
PublikacjaThe paper presents the dynamic multivariable model of Nuclear Power Plant steam turbine. Nature of the processes occurring in a steam turbine causes a task of modeling it very difficult, especially when this model is intended to be used for on-line optimal process control (model based) over wide range of operating conditions caused by changing power demand. Particular property of developed model is that it enables calculations...
-
Recuperator with microjet technology as a proposal for heat recovery from low-temperature sources
PublikacjaA tendency to increase the importance of so called dispersed generation, based on the local energy sources and the working systems uti- lizing both the fossil fuels and the renewable energy resources is observed nowadays. Generation of electricity on industrial or domestic scale together with production of heat can be obtained for example through employment of the ORC systems. It is mentioned in the EU directive 2012/27/EU for...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublikacjaEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
Applying response surface method to optimize the performance of a divergent-chimney solar power plant
PublikacjaOne of the effective tools to generate electricity from solar energy is Divergent-chimney solar power plant (DSPP). Divergent and cylindrical chimneys of solar power plants have different performances considering turbine pressure drop ratio (ft). For the first time, the divergent angle (DA) and solar radiation (SR) interaction effects on 〖ft〗_opt are discussed through applying the Computational Fluid Dynamics (CFD) and Response...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublikacjaThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublikacjaIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Numerical Study on Mitigation of Flow Maldistribution in Parallel Microchannel Heat Sink: Channels Variable Width Versus Variable Height Approach
PublikacjaMicrochannel heat sink on one hand enjoys benefits of intensified several folds heat transfer performance but on the other hand has to suffer aggravated form of trifling limitations associated with imperfect hydrodynamics and heat transfer behavior. Flow maldistribution is one of such limitation that exaggerates temperature nonuniformity across parallel microchannels leading to increase in maximum base temperature. Recently, variable...
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublikacjaResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
Compact High Efficiency and Zero-Emission Gas-Fired Power Plant with Oxy-Combustion and Carbon Capture
PublikacjaReduction of greenhouse gases emissions is a key challenge for the power generation industry, requiring the implementation of new designs and methods of electricity generation. This article presents a design solution for a novel thermodynamic cycle with two new devices—namely, a wet combustion chamber and a spray-ejector condenser. In the proposed cycle, high temperature occurs in the combustion chamber because of fuel combustion...
-
On design and analysis of flow characteristics of the last stage of gas-steam turbine
PublikacjaResearch regarding blade design and analysis of flow have been conducted for over a century. Meanwhile new concepts and design approaches were created and improved. Advancements in information technologies allowed to introduce computational fluid dynamics (CFD) and computational flow mechanics (CFM). Currently a combination of mentioned methods is used for design of turbine blades. These methods enabled us to improve flow efficiency...
-
The importance of individual spray properties in performance improvement of a urea-SCR system employing flash-boiling injection
PublikacjaThe appropriate mixing of a urea–water solution (UWS) with exhaust gases in a selective catalytic reduction system is crucial to efficiently reduce nitrogen oxides and diminish the deposition of liquid wall film. One of the methods to enhance the mixing of the UWS with the exhaust gases is a flash-boiling injection. Its positive effect has been linked with a reduced Sauter mean diameter (SMD) and improved evaporation, but the...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Modeling of Passive and Forced Convection Heat Transfer in Channels with Rib Turbulators
PublikacjaThe main goal of the research presented in this paper was the experimental and numerical analysis of heat enhancement and aerodynamic phenomena during air flow in a channel equipped with flow turbulators in the form of properly configured ribs. The use of ribs intensifies the heat transfer and at the same time increases not only the flow resistance but also the energy costs. Therefore, designing modern heat exchangers with optimal...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Measure small currents without adding resistive insertion loss
PublikacjaFloating current to voltage converter can be inserted in-line with no voltage drop and no need for a ground reference.
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublikacjaAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Marine Fuel Sulphur Limit Impact on Air Pollution
PublikacjaThe article presents calculation of Sulphur oxides percentage drop rate in marine industry recorded after 01.01.2020 when new limits, provided by International Maritime Organizations legislation, became effective. Ships’ SOx global emission was estimated and compared between 4th quarter 2019 and 1st quarter 2020. For more accurate estimation 3 seaside cities with big harbors were selected for statistical analysis. Noticeable...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublikacjaThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Zamienniki ''serwisowe'' czynnika R 22. Część I
PublikacjaW pierwszej części artykułu zestawiono dostępne na rynku czynniki chłodnicze przeznaczone do zastąpienia czynnika R 22 w istniejących układach chłodniczych bez konieczności przezbrajania instalacji. Wskazano miejsce tych mieszanin typu ''drop-in'' w technice chłodniczej. Podano skład i zasadnicze przeznaczenie poszczególnych płynów.
-
WSPÓŁCZESNE OCHŁODZENIE REJONU SZETLANDÓW POŁUDNIOWYCH I PÓŁNOCO-ZACHODNICH KRAŃCÓW PÓŁWYSPU ANTARKTYCZNEGO
PublikacjaThe paper discusses changes of hydro-climatic conditions occurring in the South Shetland Islands and in NW parts of the Antarctic Peninsula in the 1979–2016 years period. These changes are important for evaluation of the transformation of marine and coastal ecosystems. The general feature of these changes was a transition from the strong warming phase to the cooling phase, which took place around the year 2000. The paper presents...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublikacjaThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Numerical modeling of the combustion in a lab-scale pulverized-coal fired combustion chamber
PublikacjaThis work presents results of numerical modeling of the combustion process inside a lab-scale drop-tube chamber, designed to investigate the slagging properties of the flue ashes, created through the solid fuel firing. Interaction between turbulence and chemistry is accounted by use of probability density function (PDF). FLUENT inputs for non-premixed combustion chemistry modeling are defined. A discrete second phase of the coal...
-
Impulse Impedance Measurements of Lightning Protection Earthings
PublikacjaLightning protection earthing systems should be tested at currents with time parameters similar to those of lightnings. A method and definition of a measured value of impulse impedance are introduced. The impulse impedance was determined by a quotient of voltage drop on the tested earthing to a value of current in measure circuit. The usefulness of the impulse method for lightning protection evaluation is tested on radio base stations...
-
Impact response of two-layered grouted aggregate fibrous concretecomposite under falling mass impact
PublikacjaTwo-layered Grouted Aggregates Fibrous Concrete Composite (TGAFCC) is a new category concrete which became popular recently and attracted the attention of researchers globally. Recent studies indicated that TGAFCC has notable improvement in mechanical properties, which has been sufficiently documented. However, the impact behaviour of TGAFCC when combined with Glass Fibre Mesh (GFM) and Textile Fibre Mesh (TFM) is still unexplored....
-
The effect of agro-waste co-digestion and sludge disposal on carbon footprint in municipal wastewater treatment plants
PublikacjaThe study presents analysis of the carbon footprint (CF) in 6 wastewater treatment plants in northern Poland with a special focus on the effect of co digestion of sewage sludge and food waste. Although co-digestion increases the on-site energy production, but it has a negative effect on the total CF. To overcome the negative effect, several sludge disposal scenarios were analysed and their effect on the CF reduction was determined....
-
Opportunities and shortcomings of ionic liquids in single-drop microextraction
PublikacjaThe synergistic combination of ionic liquids (ILs) and single-drop microextraction (SDME) involves a powerful coupling toward the development of sustainable analytical methodologies. This overview provides a survey of the literature regarding the IL-SDME, including a database on relevant physicochemical properties of ILs for their application in SDME, the strategies implemented to combine IL-based SDME methods efficiently with...
-
Deciphering the Molecular Mechanism of Substrate-Induced Assembly of Gold Nanocube Arrays toward an Accelerated Electrocatalytic Effect Employing Heterogeneous Diffusion Field Confinement
PublikacjaThe complex electrocatalytic performance of gold nanocubes (AuNCs) is the focus of this work. The faceted shapes of AuNCs and the individual assembly processes at the electrode surfaces define the heterogeneous conditions for the purpose of electrocatalytic processes. Topographic and electron imaging demonstrated slightly rounded AuNC (average of 38 nm) assemblies with sizes of ≤1 μm, where the dominating patterns are (111) and...
-
Bias-Dependent Dynamics of Degradation and Recovery in Perovskite Solar Cells
PublikacjaDegradation of perovskite solar cells (PSCs) is often found to be partially or fully reversible when the cells are allowed to recover in the dark. Unlike the dynamics of degradation, knowledge about the dynamics of PSC cell recovery is very limited. Here, we demonstrate that the PSC recovery strongly depends on the electrical bias conditions during the light-induced degradation and that it can be manipulated by applying an external...
-
METHOD OF TRAINING THE ENDOSCOPIC VIDEO ANALYSIS ALGORITHMS TO MAXIMIZE BOTH ACCURACY AND STABILITY
PublikacjaIn the article a new training and testing method of endoscopic video analysis algorithms is presented. Classical methods take into account only eciency of recognizing objects on single video frames. Proposed method additionally considers stability of classiers output for real video input. The method is simple and can be trained on data sets created for other solutions. Therefore, it is easily applicable to existing endoscopic video...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublikacjaThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Robust identification of quadrocopter model for control purposes
PublikacjaThe paper addresses a problem of quadrotor unmanned aerial vehicle (so-called X4-flyer or quadrocopter) utility model identification for control design purposes. To that goal the quadrotor model is assumed to be composed of two abstracted subsystems, namely a rigid body (plant) and four motors equipped with blades (actuators). The model of the former is acquired based on a well-established dynamic equations of motion while the...
-
Occurrence and Levels of Biogenic Amines in Beers Produced by Different Methods
PublikacjaThe concentration of biogenic amines (BAs) in beer depends, among other factors, on the activity of microorganisms, in particular lactic acid bacteria. In this work an analytical method based on derivatization with tosyl chloride and high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was used to determine 17 BAs in samples of commercially available beers, and to monitor the changes in concentration of...
-
Ionic liquids in the microextraction techniques: the influence of ILs structure and properties
PublikacjaIonic liquids (ILs) are composed entirely of ions thus they possess unique properties, including negligible volatility, a liquid state in a broad range of temperatures and ability to change them depending on the chosen type of anion and cation, which make ILs unique and useful for many applications in sample preparation techniques. A deeper understanding of the nature of ILs and the impact of their structure on their parameters...
-
The study of structure and surface morphology of lithium titanate sol-gel derived thin films
PublikacjaIn this paper the structure and the surface morphology of lithium titanate (LTO) thin films are presented. Nanocrystalline thin films were prepared by sol–gel method. To examine the influence of the annealing time on as-prepared films crystallization, the coatings were heated at different temperatures in the range of 500 °C–600 °C for 10, 20, 40 and 80 h. The structure of the obtained material was investigated using the X-ray diffraction...
-
Analytical procedures for quality control of pharmaceuticals in terms of residual solvents content: Challenges and recent developments
PublikacjaResidual solvents play an important role in the synthesis of drugs and in product formulations. In addition, they pose a serious problem, that is toxicity, as many of them exhibit toxic or environmentally hazardous properties. Therefore, constant monitoring of quality control is needed. In this study, we present an overview of regulatory and general methods described by various pharmacopoeias. Then, the most commonly used methodologies...
-
STUDY ON THE EFFECTIVENESS OF THE TURBINE CONDENSER AIR EXTRACTION SYSTEM USING HYDRO EJECTORS
PublikacjaThe aim of the paper is to investigate the effectiveness of the 18K380 steam turbine condenser air extraction system using hydro ejectors. Motivation for the analysis is a need of improvement of the energy conversion ratio of the power plant. To achieve this goal it is necessary to establish efficiency of each subsystem of the energy cycle. The air extraction system is not a highly power consuming system but it has great impact...
-
Selecting Features with SVM
PublikacjaA common problem with feature selection is to establish how many features should be retained at least so that important information is not lost. We describe a method for choosing this number that makes use of Support Vector Machines. The method is based on controlling an angle by which the decision hyperplane is tilt due to feature selection. Experiments were performed on three text datasets generated from a Wikipedia dump. Amount...
-
The Influence of Thin Gold Electrodes on the High-Temperature Impedance of Oxide Glasses
PublikacjaThe influence of thin gold electrodes on the electrical measurements of glasses at high temperatures was studied using impedance spectroscopy. The impedance was measured several times over a wide frequency range from 10 mHz to 1 MHz and the temperature ranged from 213 to 673 K under air and nitrogen atmospheres. The results showed a drop in the conductivity of more than an order of magnitude at a temperature around 603 K during...
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublikacjaThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...