Wyniki wyszukiwania dla: TEMPERATURE INFLUENCE
-
Problems of the starting and operating of hydraulic components and systems in low ambient temperature (Part II)
PublikacjaPodczas rozruchu zespołów hydraulicznych w warunkach szoku termicznego dochodzi do dynamicznej zmiany wymiarów elementów tych zespołów. Odkształcenia elementów powodują zmianę efektywnego luzu między współpracującymi elementami. Na zmiany luzu ma pływ między innymi: różnica temperatur pomiędzy gorącym olejem a zimnym zespołem hydraulicznym, natężeniem przepływu czynnika roboczego, konstrukcji zespołu, rodzaju materiału i kształtu...
-
Effect of Temperature and Pressure on Structural and Optical Properties of Organic–Inorganic Hybrid Manganese Halides
Publikacja -
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublikacjaThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
In situ insight into the low-temperature promotion of ZIF-67 in electrocatalytic oxygen evolution reaction
Publikacja -
Low-temperature synthesis of zeolite from perlite waste — Part II: characteristics of the products
Publikacja -
Low temperature CVD growth of graphene nano-flakes directly on high K dielectrics
Publikacja -
Air temperature trends at Mount Śnieżka (Polish Sudetes) and solar activity, 1881–2012
Publikacja -
Novel Catalysts, Room Temperature, and the Importance of Oxygen for the Synthesis of Single-Walled Carbon Nanotubes
Publikacja -
MEASUREMENT OF TEMPERATURE-DEPENDENT VISCOSITY AND THERMAL CONDUCTIVITY OF ALUMINA AND TITANIA THERMAL OIL NANOFLUIDS
PublikacjaIn this study results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil is selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from...
-
Measurement of temperature-dependent viscosity and thermal conductivity of alumina and titania thermal oil nanofluids
PublikacjaThe results of simultaneous measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of two nanofluids, i.e. thermal oil/Al2O3 and thermal oil/TiO2 are presented. Thermal oil was selected as a base liquid because of possible application in ORC systems as an intermediate heating agent. Nanoparticles were tested at the concentration of 0.1%, 1% and 5% by weight within temperature range from 20°C to...
-
Improving the CPX method by specifying reference tyres and including corrections for rubber hardnes and temperature
PublikacjaRecently completed work in the EU project ROSANNE and in working group ISO/TC43/SC1/WG33 has allowed substantial improvements to measurements made by the Close-Proximity (CPX) method, intended for measurement of noise properties of road surfaces.The paper summarizes the experimental work and describes the conclusions and implementation in ISO/FDIS 11819-2 (CPX method) and in the supporting ISO (draft) Technical Specifications 11819-3...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
A new viscoelastic method of calculation of low-temperature thermal stresses in asphalt layers of pavements
PublikacjaThe paper presents a new method of calculation of thermal stresses in asphalt layers of pavements induced by cooling or heating. The method, developed by the author, is based on the analytical solution for the linear viscoelastic Burgers model extended numerically for the case of asphalt layers whose rheological parameters are strongly dependent on temperature. The coefficient of thermal expansion and Poisson’s ratio may optionally...
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublikacjaAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
High-temperature heat pumps – new devices for heat recovery and production of technological steam
PublikacjaIn the paper, the original high temperature compressor based heat pump with a dry working fluid, i.e. the one in which the slope of saturated vapour line is positive, was presented. The objective of the paper is to investigate the possibility of preparation of technological steam with tempperature 120 C from the waste heat resource at temperature of 50 C. Single comppression cycles as well as cascade systems have been considered...
-
The hydration of selected biologically relevant molecules – the temperature effect on apparent molar volume and compression
PublikacjaThe densities and sound velocities at T = (288.15, 293.15, 298.15, 303.15 and 308.15) K were measured for aqueous solutions of glycine, trimethylamine-N-oxide, taurine and N-methylacetamide. From these data, the apparent molar volumes, V the apparent molar isentropic compressions, KS,, and the Passynski hydration numbers of solutes were determined. The concentration dependencies of the calculated quantities, their limiting values...
-
The effect of calcination temperature on structure and photocatalytic properties of Au/Pd nanoparticles supported on TiO2
PublikacjaBimetallic nanoparticles, composed of two different metal elements, can exhibit peculiar electronic, optical, and catalytic or photocatalytic properties that are absent in the corresponding monometallic nanoparticles. We show the effect of calcination temperature (from 350 to 700°C) on the structure and the photocatalytic properties of Au/Pd-modified TiO2. The composition of the bimetallic Au/Pd nanoparticles in relation to their...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
High-temperature heat pumps – potential technology for heat recovery and production of process heat
PublikacjaIn the paper, the high temperature vapour compressor based heat pump with a selection of working fluids, both perspective and ecological ones, is considered. Such system is not yet commercially available on the market and in author’s opinion it has significant potential for various applications. In the presented analysis it was assumed that the heat source has a temperature of 50oC and the temperature lift is 60, 80 and 100K respectively....
-
Analytical method for calculation of heat source temperature drop for the Organic Rankine Cycle application
PublikacjaIn the paper presented are considerations on the cooperation of the limited capacity heat source with the Organic Rankine Cycle unit. Usually the heat source providing thermal energy to the Organic Rankine Cycle (ORC) may have twofold characteristics. It can be in the form of a single phase fluid, i.e. as hot exhaust gas or hot liquid, or in some cases it may be available as a phase changing fluid, as for example, technological...
-
Parameters’ Identification of Perzyna and Chaboche Viscoplastic Models for Aluminum Alloy at Temperature of 120◦C
PublikacjaThe main purpose of this paper is the parameters identification of the Perzyna and the Chaboche models for the aluminum alloy at elevated temperature. The additional purpose is comparison of the results for these viscoplastic models. The results have been verified by the numerical simulation of the laboratory tests. The material parameters have been calculated on the basis of the uniaxial tension test. The determination of the...
-
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublikacjaZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
Multimodal analysis of traction forces and the temperature dynamics of living cells with a diamond-embedded substrate
PublikacjaCells and tissues are constantly exposed to chemical and physical signals that regulate physiological and pathological processes. This study explores the integration of two biophysical methods: traction force microscopy (TFM) and optically detected magnetic resonance (ODMR) to concurrently assess cellular traction forces and the local relative temperature. We present a novel elastic substrate with embedded nitrogen-vacancy microdiamonds...
-
High temperature air/steam gasification of biomass in view of hydrogen rich gas production.
PublikacjaArtykuł przedstawia opis nowej i zaawansowanej metody konwersji termochemicznej biomasy i miejskich odpadów stałych w paliwo gazowe, bogate w wodór. W porównaniu z tradycyjnym procesem gazyfikacji, w metodzie tej wykorzystuje się powietrze/parę wodną przegrzane do wysokiej temperatury (powyżej 1300 st. C). Przegrzanie powietrza lub pary wodnej odbywa się z zastosowaniem ceramicznego przegrzewacza wysokotemperaturowego. W celu...
-
(Vapour and liquid) equilibrium in (N,N-dimethylacetamide+methanol+water) at the temperature 313.15 K.
PublikacjaPraca zawiera wyniki pomiarów całkowitej prężności pary dla tytułowego układu trójskładnikowego oraz dla ''składowych'' układów binarnych. Wyniki obliczeń nadmiarowej energii swobodnej mieszania dla układów (N,N-dimetyloaceta-mid+woda) i (N,N-dimetyloacetamid+metanol) porównane zostały z rezultatami uzyskanymi wcześniej dla innych układów (amid+metanol) oraz (amid+woda). Znaleziono interesującą zależność wartości nadmiaru...
-
Hydrogen rich gas production from high temperature air/steam gasification of biomass
PublikacjaW pracy przedstawiono nowoczesną technikę konwersji biomasy oraz stałych odpadów komunalnych w celu produkcji paliwa gazowego bogatego w wodór. Opisany proces gazyfikacji przebiega w wysokiej temperaturze przy obniżonej koncentracji tlenu i udziale pary wodnej. Dzięki temu możliwa jest produkcja gazów palnych, w szczególności H2, który można wykorzystać do produkcji energii elektrycznej i cieplnej.
-
Organic Rankine as bottoming cycle to a combined Brayton and Clausius-Rankine cycle
PublikacjaThis paper presents an enhanced approach, as it will be considered here that the ORC installation could be extra-heated with the bleed steam, a concept presented by the authors. In such way the efficiency of the bottoming cycle can be increased and an amount of electricity generated increases. A thermodynamic analysis and a comparative study of the cycle efficiency for a simplified steam cycle cooperating with ORC cycle will be...
-
The biotic and abiotic mercury at the coastal zone of Gulf of Gdańsk
Dane BadawczeConcentration of neurotoxin Hg (mercury) was determined monthly form 01.2012 to 05.2013 (total and suspended) in the surface microlayer and the surface water as well as in: phytoplankton, zooplankton, epilithon, epifithon, phytobenthos (macroalgae and angiosperms), zoobenthos, and in the sediment. The study was conducted in the coastal zone of the Puck...
-
THE MODELLING OF ACCUMULATION AND DISSIPATION OF ENERGY IN MECHANICAL DRIVE SYSTEM
PublikacjaThis paper presents a modelling of accumulation and dissipation energy in simple drive system. The simple drive system is presented by laboratory stand designed for calculate fatigue life of material for bending and rotation tests pieces. The laboratory stand was prepared to diagnosis of fatigue life of material by use energetic methods. This idea was submitted as utility model to Polish Patent Office. This laboratory stand gives...
-
Water Solubilization Using Nonionic Surfactants from Renewable Sources in Microemulsion Systems
PublikacjaIn this study the effect of temperature, NaCl andoils (hydrocarbons: C8-C16) on the formation and solubilizationcapacity of the systems of oil/monoacylglycerols(MAG):ethoxylated fatty alcohols (CEO20)/propylene glycol(PG)/water was investigated. The effects of the surfactantmixture on the phase behavior and the concentration ofwater or oil in the systems were studied at three temperatures(50, 55, 60 C) and with varied NaCl solutions...
-
EH36 steel for shipbuilding (plate thicnkness 40 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 40 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 30 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 60 mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 50 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
EH36 steel for shipbuilding (plate thicnkness 30 mm) - CMOD - force record, a0/W = 0.5
Dane BadawczeThe basic method of ductility designation of structural steels is the Charpy impact test. The test consists of a single strike of the specimen using a Charpy pendulum. Its result is the value of work necessary to break a specimen at a test temperature. Despite its many advantages, such as its short implementation time and low costs, it has its disadvantages,...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublikacjaA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
Polypyrrole based gas sensor for ammonia detection
PublikacjaThe nature of polypyrrole response to toxic gases does not allow using the sensor in a conventional way. The main aim of this study is to acquire the information about the concentration using different approaches: a linear approximation, a non-linear approximation and a tangent method. In this paper a two-steps procedure for sensor response measurements has been utilized. Polypyrrole films were electrochemically synthesized on...
-
Improved performance of LaNi0.6Fe0.4O3 solid oxide fuel cell cathode by application of a thin interface cathode functional layer
PublikacjaIn this work, novel functional layers were prepared by a low temperature spray pyrolysis method on the oxygen side of the solid oxide cells. Thin layers of Ce0.8Gd0.2O2 and LaNi0.6Fe0.4O3 are prepared between the electrolyte and the porous oxygen electrode. Additionally the influence of the sprayed ceria barrier layer on the zirconia based electrolyte with the new layers is evaluated. Impedance spectroscopy results show improvement...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublikacjaConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
Structural phase transitions in multicomponent La0.2Nd0.2Sm0.2Gd0.2RE50.2NbO4 (RE5 = Ho, Y, Tb, Eu, Pr) oxides
PublikacjaIn this work, the influence of compositional complexity on the structural and thermal properties of multicomponent rare-earth ortho-niobates from the La0.2Nd0.2Sm0.2Gd0.2RE50.2NbO4 (RE5 = Ho, Y, Tb, Eu, Pr) series have been investigated. Based on X-ray powder diffraction studies using synchrotron radiation, it was found that all tested materials were pure single-phase compositions and showed stability in the monoclinic I2/c crystal...
-
Analysis of Organic Rankine Cycle efficiency and vapor generator heat transfer surface in function of the reduced pressure
PublikacjaIn the paper presented is analysis of the influence of reduced pressure on efficiency and heat transfer area of vapor generator of Organic Rankine Cycle (ORC) in case of subcritical and supercritical parameters of operation. Compared are two cases of subcritical and supercritical ORC featuring a similar arrangement of heat source supply and heat removal, that is featuring the same temperatures of working fluid before the turbine,...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublikacjaA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Determination of binder-aggregate adhesion by contact angle measurement
PublikacjaThe key factor in asphalt pavement durability, especially in the presence of water, is adhesion of the bituminous binder to mineral aggregates. There are currently no standard laboratory test procedures that can quickly and accurately measure the strength of the interaction (bond) between the binder and aggregate. In this regard, to evaluate the adhesion force measurements based on the contact angle between the binder and the aggregate...
-
An approach for estimation of water wall degradation within pulverized-coal boilers
PublikacjaThe main aim of this paper is to estimate the lifetime of water walls of pulverized-coal boilers at nominal conditions as well as after degradation of water tubes. An approach for a pulverized-coal chamber degradation process has been formulated based on operational and experimental data. This model was formulated using on-line state monitoring of a pulverized coal burner with aim of preventing the fireplace screens from high degradation...
-
Mathematical Modeling of the Impact Range of Sewage Discharge on the Vistula Water Quality in the Region of Włocławek
PublikacjaThe paper presents results of analysis of the industrial sewage discharge influence at km 688 + 250 of the Vistula River on water quality. During the analysis, two-dimensional models of flow, impurities and temperature transport were used. Hydrological conditions of the analyzed section of the river, characteristic flows and bathymetry of the riverbed in the first instance were defined. Calculations of velocity distribution at...
-
Study on the applicability of the measurements of magnetoelastic properties for a nondestructive evaluation of thermally inducted microstructure changes in the P91 grade steel
PublikacjaThe paper presents the resuIts of the investigation of the influence of duration and temperature oftempering process on the magnetoacoustic properties of P91 tempered martensite ferritic steeI. Duringtempering of martensitic steels the dislocation density. which initially is very high. systematicallydecreases what is confirmed both by analysis of the width of X-ray diffraction peaks and hardnessmeasurements. Magnetic hysteresis...
-
Comparison of Cu1.3Mn1.7O4 spinels doped with Ni or Fe and synthesized via wet chemistry and solid-state reaction methods, designed as potential coating materials for metallic interconnects
PublikacjaThe influence of the method applied to synthesize Cu-Mn-O spinel was evaluated. The methods selected for the investigation were EDTA gel processes and solid-state reaction synthesis. From the obtained powders, sinters were prepared and assessed in terms of their properties as potential coating materials. Additionally, the influence of Ni and Fe dopants was evaluated. The results show that the EDTA gel processes method seems to...
-
Synthesis and characterization of cycloaliphatic hydrophilic polyurethanes, modified with l-ascorbic acid, as materials for soft tissue regeneration
PublikacjaIn this paper we described synthesis and characteristic of obtained hydrophilic polyurethanes (PURs) modified with ascorbic acid (commonly known as vitamin C). Such materials may find an application in the biomedical field, for example in the regenerative medicine of soft tissues, according to ascorbic acid wide influence on tissue regeneration Flora (2009), Szymańska-Pasternak et al. (2011), Taikarimi and Ibrahim (2011), Myrvik...