Wyszukiwarka
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LAYER-BY-LAYER
-
Topology Discovery of Hierarchical Ethernet LANs without SNMP support
PublikacjaThis paper presents an algorithm that allows for discovery of layer-2 hierarchical Ethernet network topology using agents running on selected end nodes. No SNMP, MIB, hardware, firmware, or operating system-level software modification is required. The method is based on transmission of customized Ethernet frames among installed software agents. It can be used to discover the topology of LAN or one VLAN segment as long as no MAC...
-
Hydrogenation process ofTiO2/BiVO4/PEDOT:PSS observed by XPS method
Dane BadawczeTitania nanotubes synthesis was based on a two-stage anodization process at water/ethylene glycol (5%/95%) electrolyte containing 0.27 M NH4F and 1 M H3PO4 described previously. Anodization process was performed in two-electrode cell compartment using platinum mesh as a cathode. The distance between electrodes was about 2 cm. The anodization voltage...
-
Statistics of AFM current-voltage curves
Dane BadawczeMapping surface electrical conductivity offers enormous cognitive possibilities regarding the structure and properties of modern materials. The technique invented for this purpose (Conductive AFM) by Murrel's team and colleagues allows independent monitoring of the local conductivity of materials in correlation with the topographic profile. The mentioned...
-
Imaging of biological samples: the ant Lasius Niger
Dane BadawczeThe world of arthropods continues to amaze researchers today. An example may be a relatively new report by a group of scientists on structures found in ant shells [1] Although calcareous anatomical structures have evolved in various groups of animals, little has been known so far about the occurrence of this type of form in insects. The authors of the...
-
Measurement spectrum obtained with the use of ZnO coated (100 nm) microsphere-based fiber-optic sensor - 200 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 100 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated (100 nm) microsphere-based fiber-optic sensor - 100 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 100 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
Measurement spectrum obtained with the use of ZnO coated (100 nm) microsphere-based fiber-optic sensor - 300 Celsius degrees
Dane BadawczeApplication of a microsphere-based fiber-optic sensor with 100 nm zinc oxide (ZnO) coating, deposited by Atomic Layer Deposition (ALD) method, for temperature measurements between 100°C and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor...
-
The Quantum Efficiency Roll-Off Effect in Near-Infrared Organic Electroluminescent Devices with Iridium Complexes Emitters
PublikacjaThe electroluminescence quantum efficiency roll-off in iridium(III)-based complexes, namely Ir(iqbt)2(dpm) and Ir(iqbt)3(iqbt=1 (benzo[b]thiophen-2-yl)-isoquinolinate, dpm=2,2,6,6-tetramethyl-3,5-heptanedionate) utilized as near-infrared emitters in organic light emitting diodes with remarkable external quantum efficiencies, up to circa 3%, 1.5% and 1%, are measured and analyzed. With a 5–6 weight % of emitters embedded...
-
High-performance NdSrCo2O5+δ–Ce0.8Gd0.2O2-δ composite cathodes for electrolyte-supported microtubular solid oxide fuel cells
PublikacjaNdSrCo2O5+δ (NSCO) is a perovskite with an electrical conductivity of 1551.3 S cm−1 at 500 °C and 921.7 S cm−1 at 800 °C and has a metal-like temperature dependence. This perovskite is used as the cathode material for Ce0.8Gd0.2O2-δ (GDC)-supported microtubular solid oxide fuel cells (MT-SOFCs). The MT-SOFCs fabricated in this study consist of a bilayer anode, comprising a NiO–GDC composite layer and a NiO layer, and a NSCO–GDC...
-
Nested Space Mapping Technique for Design and Optimization of Complex Microwave Structures with Enhanced Functionality
PublikacjaIn this work, we discuss a robust simulation-driven methodology for rapid and reliable design of complex microwave/RF circuits with enhanced functionality. Our approach exploits nested space mapping (NSM) technology, which is dedicated to expedite simulation-driven design optimization of computationally demanding microwave structures with complex topologies. The enhanced func-tionality of the developed circuits is achieved by means...
-
Zirconia-based mixed potential sensor with Pt electrode prepared by spin-coating of polymeric precursor
PublikacjaMany types of yttria-stabilized zirconia (YSZ) based gas sensors have been explored extensively in recent years. Great attention have been directed to mixed-potential-type gas sensors. It is due to growing concerns with environmental issues. Not without a significance is the fact of very attractive performance of this type of sensor allowing to detect low concentration of pollutant gases. In this paper two types of YSZ based mixed-potential...
-
X-Ray Computer Tomography Study of Degradation of the Zircaloy-2 Tubes Oxidized at High Temperatures
PublikacjaThe investigations of high-temperature oxidation of zirconium alloys, applied for fuel pellets in nuclear power plants, are usually limited to oxidation kinetics, phase transformations and microstructural characterization. The purpose of this research was to characterize the degradation phenomena occurring within oxide layer and at the interface oxide/metal, on internal and external Zircaloy-2 tube...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
The analysis of the influence of the corrosion protection method of selected steel elements on the steel structure life cycle costs
PublikacjaSteel products are widely used in the construction for the performance of essential and additional elements of engineering structures. They are characterized by high tensile strength, compression and bending, the structure homogeneity, the possibility of assembly regardless of the season and climatic conditions, ease of processing and the possibility of almost any shape. The main disadvantage of steel structures is their high susceptibility...
-
Evaluation of citric acid corrosion inhibition efficiency and passivation kinetics for aluminium alloys in alkaline media by means of dynamic impedance monitoring
PublikacjaA novel approach is proposed for constructing the adsorption isotherm in corrosion studies, based on a well-known interaction between citric acid and aluminium in alkaline electrolytes. Our approach utilizes the instantaneous impedance measurements via Dynamic Electrochemical Impedance Spectroscopy in galvanostatic mode (g-DEIS). Unlike other common tools, g-DEIS delivers exact information about the concentration required for full...
-
Quantitative loss analysis of opaque perovskite solar cells using transient and steady-state characterization
PublikacjaPerovskite solar cells have emerged as a promising technology in the field of photovoltaics, owing to their notable advancements in power conversion efficiency. Recent investigations have revealed a crucial dependency of efficiency on the source of bromide within the perovskite absorption layer. To elucidate the underlying nature of traps within these solar cells, a comprehensive series of measurements was conducted under varying...
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublikacjaCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...
-
COMPARISON OF THE CONVENTIONAL AND ALTERNATIVE GRANULAR MATERIALS FOR DUAL-MEDIA FILTRATION OF GROUNDWATER: PILOT PLANT TESTING
PublikacjaNowadays, occurrence of abnormal mineral or organic natural (geogenic) compounds concentrations, in ground and infiltration water, but also quite often in surface waters, is now a common problem encountered in Poland, Europe and many other countries throughout the world. The most concern is usually paid on the removal of iron (Fe) and manganese (Mn) as well as anthropogenic compounds (in particular referring to the organic compounds...
-
Structural properties of hydration shell around various conformations of simple polypeptides
PublikacjaIn this paper we investigate structural properties of water within the solvation shell around the peptide core created by a well-defined conformation of polypeptide chain. The following secondary structures are investigated: linear (straight chain), and three helices PII (polyproline-like), 310, and α. We propose using the two-particle contribution to entropy as a rational measure of the water structural ordering within the solvation...
-
Badanie właściwości czujników wilgotności na bazie nanocząstek tlenku cynku
PublikacjaW celu pomiaru wilgotności szeroko stosowane są czujniki elektryczne. Warstwą czynną, zmieniającą swoje właściwości pod wpływem pary wodnej, stanowią najczęściej materiały ceramiczne lub polimerowe. Tlenek cynku jest jednym z materiałów ceramicznych będących dobrym kandydatem do zastosowania go jako warstwy czynną w czujnikach wilgotności. W tej pracy przedstawiono wyniki badań właściwości struktur czujnikowych z warstwą tlenku...
-
Aktywny system RFID do lokalizacji i identyfikacji obiektów w wielomodalnej infrastrukturze bezpieczeństwa
PublikacjaPrzedstawiono prace koncepcyjne, badawcze oraz implementacyjne skoncentrowane na praktycznej realizacji systemu detekcji obiektów z wykorzystaniem kamer wizyjnych i identyfikacji radiowej. Zaproponowano rozbudowę wielomodalnego teleinformatycznego systemu bezpieczeństwa o warstwę identyfikacji radiowej obiektów. Omówiono założenia zaprojektowanego systemu oraz opracowaną warstwę sprzętową. Zaproponowano i przedyskutowano praktyczne...
-
Application of IR UWB Spectrum Shaping to IEEE 802.15.4a Standard
PublikacjaCoexistence of existing narrowband systems and new ultra wideband devices in the same frequency range requires using some interference mitigation techniques, for example based on spectrum shaping. This paper presents efficiency of impulse radio spectrum shaping methods, applied to IEEE 802.15.4a UWB alternate physical layer signals. Basic parameters of 802.15.4a signal structure and outline of proposed spectrum shaping methods...
-
How water mediates the long-range interactions between remote protein molecules
PublikacjaThe high crowding of macromolecules in the cytoplasm affects the processes that occur inside a living cell. It can, for example, promote the forming of various loosely connected structures of proteins. It also means that bulk water is, essentially, not present there. The relatively thin layer of solvent that separates macromolecules may be able to participate in the long-range interactions between them and make them respond to...
-
Electrochemically directed biofunctionalization of a lossy-mode resonance optical fiber sensor
PublikacjaIn this work, we present a direct electrochemical biofunctionalization of an indium-tin-oxide-coated lossy-mode resonance optical fiber sensor. The functionalization using a biotin derivative was performed by cyclic voltammetry in a 10 mM biotin hydrazide solution. All stages of the experiment were simultaneously verified with optical and electrochemical techniques. Performed measurements indicate the presence of a poly-biotin...
-
ANALYSIS OF THE PUNCHING FAILURE MECHANISM IN WORKING PLATFORMS
PublikacjaPaper presents an analysis of the shear failure mechanism which occurs from the punching of a working platform layer in relation to its thickness, grain size arrangement and mechanical properties, taking into consideration the interaction with soft subgrade. The study is based on the observations of performance of natural scale structures (Streefkerk) and the results of model investigations numerically represented with the use...
-
Effect of crystallization process at cryogenic conditions on the functional properties of the SUPERSTON alloy used in production the ship's propellers
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the SUPERSTON alloy used for ship's propellers. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. During the laser remelting at cryogenic conditions the microstructure changes significantly. This is related to synergistic effects of the solidification rate, phase transformations...
-
Effect of electrode resistance on admittance spectra of planar organic device carrying SCLC and on charge carrier mobility extracted from susceptance
PublikacjaThe work presents small signal admittance spectra of a sandwich system with thin organic layer carrying a space charge limited current. The effect of series resistance of electrodes on the spectra is discussed. Spectra of small signal capacitance are added to get more detailed insight. The analysis performed shows that the series resistance can affect both parts of small signal response within a whole range of frequency. Moreover,...
-
Elctrochemical oxidation and corrosion resistance of the Ti13Nb13Zr alloy
PublikacjaThis paper presents the results of oxidation and corrosion tests carried out on titanium alloy Ti13Nb13Zr. The oxide film was prepared by electrochemical environment 2M H3PO4 for 30 min and 1 h, at a constant voltage 40V. The tests of corrosion resistance were performed by potentiostatic method in Ringer's solution at different pH values: 7, 5 and 3. The change in an appearance of surface and the increase in corrosion resistance...
-
Retrieval with Semantic Sieve
PublikacjaThe article presents an algorithm we called Semantic Sieve applied for refining search results in text documents repository. The algorithm calculates socalled conceptual directions that enables interaction with the user and allows to narrow the set of results to the most relevant ones. We present the system where the algorithm has been implemented. The system also offers in the presentation layer clustering of the results into...
-
Performance of ASON/GMPLS architecture in condition of wavelength conversion and without wavelength conversion
PublikacjaThe paper regards the problem of ASON/GMPLS performance in condition of wavelength and without wavelength conversion. The authors present influence analysis in condition of wavelength and non-wavelength conversion on the ASON/GMPLS control plane performance represented by mean Connection Set-up Time E (CST) and request loss probabilities. The offered traffic to the transport layer and request intensity have been changed for evaluation...
-
Modeling of Combined Phenomena Affecting an AUV Stealth Vehicle
PublikacjaIn the paper some results of research connected with modelling the basic stealth characteristics of an AUV vehicle are presented. First of all a general approach to design of the stealth AUV autonomous underwater vehicle under consideration is introduced. Then, the AUV stealth vehicle concept is briefly described. Next a method of modelling of the stealth characteristics is briefly described as well. As an example of the stealth...
-
Selfish Attacks in Two-Hop IEEE 802.11 Relay Networks: Impact and Countermeasures
PublikacjaIn IEEE 802.11 networks, selfish stations can pursue a better quality of service through selfish MAC-layer attacks. Such attacks are easy to perform, secure routing protocols do not prevent them, and their detection may be complex. Two-hop relay topologies allow a new angle of attack: a selfish relay can tamper with either source traffic, transit traffic, or both. We consider the applicability of selfish attacks and their variants...
-
Radio Link Measurement Methodology for Location Service Applications
PublikacjaThe aim of this paper is the methodology of measurements executed in a radio link for the realization of radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the universal mobile telecommunications system (UMTS) are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation...
-
Porównanie algorytmów MGA i NGA do projektowania i optymlizacji kombinacyjnych układów cyfrowych z algorytmem MLCEA.
PublikacjaW artykule zaprezentowano porównanie algorytmów ewolucyjnych do projektowania i optymalizacji kombinacyjnych układów cyfrowych. Porównano algorytmy MGA (Multiobjective Genetic Algorithm) i NGA (Genetic Algorithm with N-cardinality Reprezentation) z utworzonym algorytmem MLCEA (Multi-Layer Chromosome Evolutionary Algorithm), bazującym na reprezentacji osobników w postaci chromosomów wielowarstwowych. Otrzymane wyniki dla algorytmu...
-
Low frequency nois of supecapacitor
Dane BadawczeDataset contains noise measurement results on prototype electrochemical double layer capacitor. The measurement procedure is described in https://dx.doi.org/10.1515/mms-2017-0059.
-
Photocatalytic ethylene decomposition with the use of fluidized bed photoreactor
Dane BadawczeData contain exported raw data recorded during decomposition of ethylene during utilization of fluidized bed photoreactor equipped with either UV-LEDs or fluorescent UV lamps as well as in either humid or dry conditions. In separate folder, the photographs of the photocatalytic system were included. As photocatalytic material, polystyrene spheres coated...
-
Wpływ usług on-line na budowanie pozytywnych relacji i lojalności klienta
PublikacjaW artykule omówiono wybrane problemy projektowe dotyczące współczesnych usług on-line w kontekście budowania trwałej lojalności klienta. Przedstawiono model warstwowego rozwoju usług on-line wraz z zaleceniami projektowymi zorientowanymi na budowanie i wzmacnianie lojalności klienta. Przedstawiono przykłady scenariuszy rozwoju usług e-zdrowia online. Przedstawiono możliwości dalszego rozwoju prezentowanego podejścia i plany dalszych...
-
Membrane-SPME the best 'green' sample preparation technique for the gas chromatographic determination polar organic pollutants in polar media
PublikacjaOne of the most popular technique for sample preparation, which fulfill requirements of green analytical chemistry, is solid phase microextraction (SPME). Because of the undoubted advantages of SPME technique, solvent-free character of the extraction process and the enormous potential in analytical practice, a series of studies has been undertaken to develop new technical solutions, where improving the sensitivity and the extraction...
-
Liquid chromatography techniques for separation of flavonoids from Droseraceae
PublikacjaFlavonoids which are presented in insectivorous plants of the Droseraceae family have wide range of advantageous properties i.e. an antioxidant, anti-inflammatory and antimicrobial activities, antitumor activity was reported as well.The purpose of the research was to develop the most favourable conditions for liquid chromatographic separation and identification of myricetin and quercetin in extracts of insectivorous plants. In...
-
Polymer based thick films - material quality and interface resistance evaluation
PublikacjaThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
The mechanisms of degradation of titanium dental implants
PublikacjaTitanium dental implants show very good properties, unfortunately there are still issues regarding material wear due to corrosion, implant loosening, as well as biological factors—allergic reactions and inflammation leading to rejection of the implanted material. In order to avoid performing reimplantation operations, changes in the chemical composition and/or modifications of the surface layer of the materials are used. This research...
-
Development and Assessment of Regeneration Methods for Peptide-Based QCM Biosensors in VOCs Analysis Applications
PublikacjaCleaning a quartz crystal microbalance (QCM) plays a crucial role in the regeneration of its biosensors for reuse. Imprecise removal of a receptor layer from a transducer’s surface can lead to unsteady operation during measurements. This article compares three approaches to regeneration of the piezoelectric transducers using the electrochemical, oxygen plasma and Piranha solution methods. Optimization of the cleaning method allowed...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublikacjaSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
High gain/bandwidth off‑chip antenna loaded with metamaterial unit‑cell impedance matching circuit for sub‑terahertz near‑field electronic systems
PublikacjaAn innovative off-chip antenna (OCA) is presented that exhibits high gain and efficiency performance at the terahertz (THz) band and has a wide operational bandwidth. The proposed OCA is implemented on stacked silicon layers and consists of an open circuit meandering line. It is shown that by loading the antenna with an array of subwavelength circular dielectric slots and terminating it with a metamaterial unit cell, its impedance...
-
The influence of small intestinal mucus structure on particle transport ex vivo
PublikacjaMucus provides a barrier to bacteria and toxins while allowing nutrient absorption and waste transport. Unlike colonic mucus, small intestinal mucus structure is poorly understood. This study aimed to provide evidence for a continuous, structured mucus layer and assess the diffusion of different sized particles through it. Mucus structure was assessed by histology and immunohistochemistry. Ultra-structure was assessed by scanning...
-
The possibility of estimating the height of the ionospheric inhomogeneities based on TEC variations maps obtained from dense GPS network
PublikacjaA state of the ionosphere can be effectively studied using electromagnetic signals received from global navigation satellite systems (GNSS). Utilization of the dual frequency observations allows estimating values of the total electron content (TEC). They can be used for a number of scientific studies such as detection and monitoring of traveling ionospheric disturbances or plasma bubbles. Moreover, maps of TEC variations allow...
-
High frequency impulse ground penetrating radar application in assessment of interlayer connections
PublikacjaGround Penetrating Radar (GPR) technique is commonly used in the nondestructive evaluation of pavement structures. In particular, this method is used to estimate thicknesses of pavement layers as well as it can be utilized in advanced studies of pavement structures. The device presented in this paper comprise the high frequency impulse antennas that allow for investigating the interlayer zones in terms of their electromagnetic...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublikacjaMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
The treatment of wastewater containing pharmaceuticals in microcosm constructed wetlands: the occurrence of integrons (int1–2) and associated resistance genes (sul1–3, qacEΔ1)
PublikacjaThe aim of this study was to analyze the occurrence of sulfonamide resistance genes (sul1–3) and other genetic elements as antiseptic resistance gene (qacEΔ1) and class 1 and class 2 integrons (int1–2) in the upper layer of substrate and in the effluent of microcosm constructed wetlands (CWs) treating artificial wastewater containing diclofenac and sulfamethoxazole (SMX), which is a sulfonamide antibiotic. The bacteria in the substrate...
-
Design and Experimental Validation of a Metamaterial-Based Sensor for Microwave Imaging in Breast, Lung, and Brain Cancer Detection
PublikacjaThis study proposes an innovative geometry of a microstrip sensor for high-resolution microwave imaging (MWI). The main intended application of the sensor is early detection of breast, lung, and brain cancer. The proposed design consists of a microstrip patch antenna fed by a coplanar waveguide with a metamaterial layer-based lens implemented on the back side, and an artificial magnetic conductor (AMC) realized on as a separate...