Wyszukiwarka
Wyniki wyszukiwania dla: water lubrication
-
Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect
Publikacja -
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublikacjaWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Micro- and nano-level of bio-joint lubrication = Smarowanie biołożysk na poziomie mikro i nano
PublikacjaSmarowanie stawów człowieka koncentruje się w głównej mierze na tarciu granicznym oraz na tarciu mieszanym w cienkiej warstwie cieczy synowialnej zalegającej pomiędzy łatwo odkształcalnymi powierzchniami miękkiej chrząstki stawowej, na której wysokości chropowatości zmieniają się z czasem trwania procesu smarowania.Wartości sił tarcia granicznego ulegają zmianie w przypadku zmian wysokości nierówności dochodzących do dziesiątych...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
-
Stochastyczne nieizotermiczne smarowanie stawu biodrowego z odkształcalną chrząstką = Stochastic nonisothermic lubrication of hip joint with deformable cartilage
PublikacjaW niniejszej pracy przedstawiono metodę rozwiązywania problemu nieizotermicznego smarowania naturalnych stawów biodrowych człowieka oraz endoprotez z uwzględnieniem deformacji powierzchni stawowych oraz związanych z tym faktem efektów losowych. Przedstawiono również wyniki pomiarów powierzchni głów kostnych na Aparacie Rank-Taylor Hopson Talyscan 150. Uzyskane wyniki zostały opracowane z użyciem programu komputerowegoTalymap-Expert.
-
Wysokociśnieniowe uszczelnienia ruchu obrotowego wału hydraulicznych maszyn wyporowych
PublikacjaW artykule przedstawiono wyniki badań mające na celu wytypowanie węzła uszczelniającego wał silnika hydraulicznego zapewniającego najwyższą trwałość przy smarowaniu wodą. Parametry pracy: ciśnienie 2 MPa i minimalna prędkość poślizgu uszczelek 2 m/s. Opisano również nowatorski przyrząd, na którym przeprowadzono pomiary wszystkich parametrów węzła uszczelniającego.
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
The Influence of the Application of EP Additive in the Minimum Quantity Cooling Lubrication Method on the Tool Wear and Surface Roughness in the Process of Turning 316L Steel
Publikacja -
Viscoelastic lubrication of human hip joint for impulsive motion after injury. Lepkosprężyste smarowanie stawu biodrowego człowieka dla impulsywnego ruchu po urazie.
PublikacjaW pracy rozpatruje się urazy wywołujące zmniejszenie lub zwiększenie wysokości i zmiany kształtu szczeliny stawu, które to zmiany po pewnym określonym czasie po doznanym urazie mogą zanikać. W konsekwencji takich urazów i to w bardzo krótkim czasie rzędu mikrosekund następują bardzo istotne zmiany parametrów smarowania. Mamy tu na uwadze zmiany rozkładów wartości ciśnienia i sił nośnych. Takie zmiany warunków smarowania nieustalonego...
-
Albumin–Hyaluronan Interactions: Influence of Ionic Composition Probed by Molecular Dynamics
PublikacjaThe lubrication mechanism in synovial fluid and joints is not yet fully understood. Nevertheless, intermolecular interactions between various neutral and ionic species including large macromolecular systems and simple inorganic ions are the key to understanding the excellent lubrication performance. An important tool for characterizing the intermolecular forces and their structural consequences is molecular dynamics. Albumin...
-
Bio and slide bearings: their lubrication by non-Newtonian fluids and application in non conventional systems. Vol.3. Tribology processes for cells human joints and micro-bearings
PublikacjaW niniejszej monografii przedstawiony został aktualny pogląd dotyczący procesu smarowania stawów człowieka od strony mechaniki, a szczególnie hydromechaniki i metod matematycznych. Wyznaczono pola prędkości przepływu lepkiej, odżywczej nie Newtonowskiej cieczy biologicznej, a także powstające siły tarcia w trakcie ruchu cieczy w warstwie granicznej wokoło współpracujących powierzchni. Dodatkowo rozpatrywano przepływy potencjalne...
-
Unsteady periodic pressure and capacity for viscoelastic lubrication in spherical hip joint. Nieustalone okresowe ciśnienie i nośność w lepkosprężystym smarowaniu sferycznego stawu biodrowego.
PublikacjaNiniejsza praca przedstawia obliczenia numeryczne rozkładu wartości ciśnienia i siły nośnej podczas hydrodynamicznego smarowania w szczeliny stawu biodrowego człowieka przy uwzględnieniu okresowego ruchu niestacjonarnego oraz lepkosprężystych właściwości cieczy synowialnej, zmieniających się w czasie. Takie właściwości cieczy synowialnej nie były uwzględniane w dotychczasowych pracach naukowych przy modelowaniu numerycznym stawu...
-
Hyaluronan-Chondroitin Sulfate Anomalous Crosslinking Due to Temperature Changes
PublikacjaGlycosaminoglycans are a wide class of biopolymers showing great lubricating properties due to their structure and high affinity to water. Two of them, hyaluronic acid and chondroitin sulfate, play an important role in articular cartilage lubrication. In this work, we present results of the all-atom molecular dynamics simulations of both molecules placed in water-based solution. To mimic changes of the physiological conditions,...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublikacjaIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
Studies of the Interaction Dynamics in Albumin-Chondroitin Sulfate Systems by Recurrence Method
PublikacjaThe physicochemical basis of lubrication of articular cartilage is still not fully understood. However, the synergy between components of the synovial fluid can be a crucial factor that could explain this phenomenon. This work presents a nonlinear data analysis technique named the recurrence method, applied to the system involving two components of synovial fluid: albumin and chondroitin sulfate (CS) immersed in a water environment....
-
Physical crosslinking of hyaluronic acid in the presence of phospholipids in an aqueous nano-environment
PublikacjaHyaluronic acid and phospholipids are two components in the synovial joint cavity that contribute to joint lubrication synergistically. Molecular dynamics simulations were performed and hydrogen bonds in hyaluronic acid were analyzed to identify specific sites that are responsible for its physical cross-linking. Two molecular masses of hyaluronic acid, 10 kDa and 160 kDa, were considered. We use molecular dynamics simulations and...
-
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio - Tribological Applications
PublikacjaA method is presented for the comparative testing of wear resistance of ceramic coatings made from materials potentially feasible in tribo - medical applications, mainly orthopaedic implants made from ceramics coated metals for low cost, long life and low wear particle emission into the body. The method was devised as the main tool for use in research and is comprised of flat on flat and ball on flat surface (sliding) tests. Seven...
-
Application of the Optimization Methods to the Search of Marine Propulsion Shafting Global Equilibrium in Running Condition
PublikacjaFull film hydrodynamic lubrication of marine propulsion shafting journal bearings in running condition is discussed. Considerable computational difficulties in non-linear determining the quasi-static equilibrium of the shafting are highlighted. The approach using two optimization methods (the particle swarm method and the interior point method) in combination with the specially developed relaxation technique is proposed to overcome...
-
An electric ring thruster as auxiliary manoeuvring propulsion system for watercraft - construction analysis
PublikacjaThe reported project aimed at examining properties and purposefulness of use of modern electromagneticbearings for a screw propeller in a prototype version of a synchronous ring motor with rare earths magnets.Bearings of this type generate electromagnetic forces which keep the rotor in a state of levitation. Therotating machine with magnetic bearings can work in any environment which reveals diamagnetic properties(air, vacuum,...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Te use of acoustic emission for assessment of the oil lubricity in a four-ball tester
Publikacjain view of the increased dynamic and temperature load in the compression-ignition engine tribological systems, particular attention is drawn to the problem of such lubrication of the friction nodes that after breaking the boundary layer it could be restored without any wear occurring. therefore, an idea has been devised of introducing to friction nodes, with the lubrication oils, of new substances (operational preparations) modifying...
-
Anomalous Behavior of Hyaluronan Crosslinking Due to the Presence of Excess Phospholipids in the Articular Cartilage System of Osteoarthritis
PublikacjaLubrication of articular cartilage is a complex multiscale phenomenon in synovial joint organ systems. In these systems, synovial fluid properties result from synergistic interactions between a variety of molecular constituent. Two molecular classes in particular are of importance in understanding lubrication mechanisms: hyaluronic acid and phospholipids. The purpose of this study is to evaluate interactions between hyaluronic acid...
-
Experimental comparison of the transition speed of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaA journal bearing test bench is used to find the transition speed between the hydrodynamic and mixed lubrication regimes for a modified magnetorheological (MR) fluid. It is shown that the transition speed of the bearing can be reduced by applying a local magnetic field near minimum film when it is lubricated with the MR fluid, and that this will only marginally increase friction. The lubricating performance of the MR fluid is compared...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublikacjaLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
Investigating lubricants behaviour in microgravity for vibration damping purposes
PublikacjaVibration is one of the harshest environments an object is exposed to during and after launch into space on a launch vehicle. Such vibrations should be damped to avoid destruction of the spacecraft or its elements. Currently, active and material damping is used. A possibility of using lubrication as the damping factor is suggested by some research. MoS2 is a typical solid lubricant used in space applications. Its properties vary...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublikacjaTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
-
Fatigue resistance investigation of the IC engine MB11 bearings, working under conditions of dynamic unidirectional loadings
PublikacjaThe slide bearing material MB11 fatigue resistance has been investigated with the application of SMOK - test stand in which dynamic unidirectional loadings to the test bearing is generated. Slide bearing layer consists of the bronze MB11 ( Cu Pb22 Sn 3 ) sintered to the steel shell. Each of the tested bearing has been subject to the standard 20-hour test, under conditions of the full fluid lubrication. Methodology of the experiments,...
-
Environmentally acceptable lubricants (EAL) compared with a reference mineral oil as marine stern tube bearing lubricant – Experimental and theoretical investigations
PublikacjaThe purpose of this research is to indicate the potential differences in bearing characteristics resulting from the application of different lubricant types with the same viscosity grade. The effect of different environmentally acceptable lubricants (EALs) on hydrodynamic journal bearing properties is studied experimentally and compared to the properties obtained after lubrication with a reference mineral oil. The results of the...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
INVESTIGATION OF JOURNAL SLIDE BEARINGS UNDER THE ANGLE OF THEIR FUNCTIONING
PublikacjaPaper presents the structure and principle of operation of a stand for measurements of influence of the lubrication method and process on functioning of journal slide bearings in their various technical states. Measurements performed on the stand make it possible to take advantage of the new method of evaluating the influence of physical and chemical properties of lubricating oil on the coefficient of friction in the mixed friction...
-
Influence of Asphalt Binder on the Compactability of Asphalt Mixtures Using Locking Point
PublikacjaCompaction is an important process for the asphalt mixture service life. A properly compacted mixture is crucial for long-lasting pavement. The objective of this study was to evaluate the influence of asphalt binders on the compactability of the asphalt mixtures by utilizing the concept of the locking point. To achieve this objective, two compaction methods (impact and gyration), different temperatures and asphalt content, and...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublikacjaThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Reliability model of slide bearings with particular attention given to lubricating oil
PublikacjaThe paper presents the slide bearing with circulating lubrication as a system of series three-element structure, where lubricating oil is the weakest link. In accordance with the Pierce statement that ''strength of chain is the strength of its weakest link'', a bearing reliability model has been developed. It allows to use the lubricating oil to evaluate the probability of correct working of the whole slide bearing, i.e. the reliability....
-
Study of a Multicriterion Decision-Making Approach to the MQL Turning of AISI 304 Steel Using Hybrid Nanocutting Fluid
PublikacjaThe enormous use of cutting fluid in machining leads to an increase in machining costs, along with different health hazards. Cutting fluid can be used efficiently using the MQL (minimum quantity lubrication) method, which aids in improving the machining performance. This paper contains multiple responses, namely, force, surface roughness, and temperature, so there arises a need for a multicriteria optimization technique. Therefore,...
-
IDENTIFICATION OF THE INTERFECE OF LATERAL SLIDE BEARINGS
PublikacjaIn the paper, the model of slide bearings of motor engine, the metodology of research on this type of bearings and its results are presented measurement standpoint consisting of main elements of Briggs & Stratton 550 serie 10 T 802 model piston motor engine driven by three phase elektric engine is introduced . On the measurement standpoint are measurements were done, needed for specification...
-
NEW DESIGNS OF CENTRIFUGAL MAGNETIC FLUID SEALS FOR ROTATING SHAFTS IN MARINE TECHNOLOGY
PublikacjaThe centrifugal magnetic fluid seals have important advantage over the conventional centrifugal seals. They maintain very good sealing capacity at static, medium and high speeds of shaft rotation, with the increased seal lifetime, and minimum torque and static friction. These seals are particularly useful in cases when the angular shaft velocity varies and sometimes decreases to nearly or exactly zero, such as in flywheel applications,...
-
Formation of Protein Networks between Mucins: Molecular Dynamics Study Based on the Interaction Energy of the System
PublikacjaMolecular dynamics simulations have been performed for a model aqueous solution of mucin. As mucin is a central part of lubricin, a key component of synovial fluid, we investigate its ability to form cross-linked networks. Such network formation could be of major importance for the viscoelastic properties of the soft-matter system and crucial for understanding the lubrication mechanism in articular cartilage. Thus,the inter- and...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 4-8h.
Dane BadawczeWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 4-8h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 0-4h.
Dane BadawczeWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer.Running time: 0 - 4h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21, #22-#23, #24-#25, #26-#27,...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #24 - #25.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #24 (upper, rotating), #25 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #30 - #31.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #30 (upper, rotating), #31 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #20 - #21.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #20 (upper, rotating), #21 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #22 - #23.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #22 (upper, rotating), #23 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #28 - #29.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #28 (upper, rotating), #29 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Specimen running-in. Prep. to sliding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specimen set #26 - #27.
Dane BadawczeSpecimen running-in procedure. Preparation to sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. Specimen set #26 (upper, rotating), #27 (lower, non-rotating)CZ_PRZYS.MAT - accelerometerMOM_TAR.MAT...
-
Study of Slip Effects in Reverse Roll Coating Process Using Non-Isothermal Couple Stress Fluid
PublikacjaThe non-isothermal couple stress fluid inside a reverse roll coating geometry is considered. The slip condition is considered at the surfaces of the rolls. To develop the flow equations, the mathematical modelling is performed using conservation of momentum, mass, and energy. The LAT (lubrication approximation theory) is employed to simplify the equations. The closed form solution for velocity, temperature, and pressure gradient...
-
ASSESSING THE POTENTIAL REPLACEMENT OF MINERAL OIL WITH ENVIRONMENTALLY ACCEPTABLE LUBRICANTS IN A STERN TUBE BEARING: AN EXPERIMENTAL ANALYSIS OF BEARING PERFORMANCE
PublikacjaT his study compares the performance of a plain bearing, with a similar structure to a tail shaft stern bearing, lubricated with either mineral oil or an environmentally acceptable lubricant (EAL). The main characteristic of the bearing is its length/diameter ratio of <1. Measurements are carried out with the bearing operating under loads from 0.5 to 1 MPa and seven speeds ranging from 1 to 11 rev/s. The bearing lubricated...
-
Assessment of unusual failure in crankshaft of heavy-duty truck engine
PublikacjaThe unusual premature failure of a heavy-duty truck engine crankshaft has been the subject of a rigorous study, and this manuscript describes it in detail. The failure was happened to begin with the growth of the crack from the surface defects, in the form of the clusters of non-metallic inclusions, in the lubrication hole zone of the first main journal, which was the stress concentration zone. A series of experiments including...
-
Research on Linear Actuators for Active Foil Bearings
PublikacjaActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...