Filtry
wszystkich: 1323
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: POLYMER SLIDING BEARINGS
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublikacjaGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublikacjaFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublikacjaA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
GOOD HEALTH PRODUCTS AND POLYMER COMPOSITES OBTAINED WITH THE USE OF NATURAL ORIGIN MICRO- AND NANOFIBERS
PublikacjaThe aim of this work was focused on good health products and polymer composites obtained with the use of natural origin micro- and nanofibers. Many different type of the natural plants are used in the production of good health products and polymer processing like curcuma, cellulose, microalgae and others. Often are used as a antioxidants and fillers. In this work the effect of algae and cellulose as a microfillers on the chosen...
-
Experimental study on the effectiveness of polymer damper in damage reduction of temporary steel grandstand
PublikacjaA large number of accidents, involving collapses of temporary grandstands during different types of events, were observed in the past. If the synchronized movement of people is tuned with the natural frequency of the affected part of the structure, resonance might occur. It may lead to severe damages of grandstands, their collapse or panic among the spectators. The aim of the paper is to assess, through preliminary experimental...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublikacjaThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublikacjaAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
Robust asymptotic super twisting sliding mode observer for non-linear uncertain biochemical systems
PublikacjaThe problem of state estimation (reconstruction of the state vector) for a given class of biochemical systems under uncertain system dynamics has been addressed in this paper. In detail, the bioreactor at a water resource recovery facility represents the considered biochemical systems. The biochemical processes taking place in the bioreactor have been modelled using an activated sludge model. Based on this model, an appropriate...
-
IRANIAN POLYMER JOURNAL
Czasopisma -
Polymer based thick films - material quality and interface resistance evaluation
PublikacjaThe properties of polymer based thick film layers mede using different resistive pastes and dipping silvers have been studied. The composite of carbon and graphite (C/Gr) conducting particles suspended in different polymer vehicles were used for preparation resistive layers. Interface resistance Rc created between dipping silver (DiAg) contact layer and resistive layer was determined from the surface potential distribution measurements...
-
Comparable analysis of PID controller settings in order to ensure reliable operation of active foil bearings
PublikacjaIn comparison to the traditional solutions, active bearings offer great operating flexibility, ensure better operating conditions over a wider range of rotational speeds and are safe to use. In order to ensure optimum bearing performance a bearing control system is used that adapts different geometries during device operation. The selection of optimal controller parameters requires the use of modern optimization methods that make...
-
Effect of wear on EHD film thickness in sliding contacts
Publikacja -
Role of reciprocating sliding testing in tribological materials engineering
PublikacjaPrzedstawiono wyniki badań oporu ruchu i zużycia skojarzeń o styku rozłożonym przy posuwisto-zwrotnym ślizganiu. Badano skojarzenia: żeliwo-stop aluminium przetapiany laserowo w warunkach kriogenicznych oraz żeliwo-kompozyt aluminium-żelazo otrzymany ''in situ''.
-
The surface contact characteristics after sliding and rolling burnishing.
PublikacjaW pracy przedstawiono zastosowanie nowej metody SCGC i odpowiedniego programu komputerowego JKC do oceny pomierzonej mikrostereometrii powierzchni części maszyn, głównie na potrzeby kontroli jakości. Na przykładzie powierzchni nagniatanych wykazano cechy nowej metody: wizualizację ułatwiającą wyobrażenie pomierzonej sfery chropowatości, położenie w niej najważniejszych parametrów oceny (rozkład geometrycznej powierzchni kontaktu,...
-
Temperature measurements in monitoring of large thrust bearings
PublikacjaW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła (IPHC).
-
Temperature Measurements in Monitoring of Large Thrust Bearings
PublikacjaW pracy przedstawiono krytyczną ocenę popularnego systemu diagnostyki dużych łożysk wzdłużnych (np. łożysk nośnych hydrogeneratorów), w którym stosowany jest jednopunktowy pomiar temperatury w klockach łożyskowych. Stwierdzono, że taki układ pomiarowy nie pozwala na bezpieczną eksploatację łożysk, ponieważ posiada bardzo duże opóźnienie czasowe, nie daje informacji o lokalnych zagrożeniach, nie pozwala racjonalnie ustalić poziomów...
-
Temperature measurements in monitoring of large thrust bearings
PublikacjaW pracy przedstwiono krytyczną analizę aktualnych metod diagnostyki dużych hydrodnamicznych łożysk wzdłużnych hydrozespołów elektrowni wodnych. Wykazano niedostatki i zagrożenia płynące ze stosowania diagnostyki opartej na jednopunktowym pomiarze temperatury. Zaprezentowano wstępna koncepcję nowej metody diagnostycznej opartej na odwrotnym zagadnieniu przepływu ciepła.
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublikacjaCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublikacjaThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Coffee Wastes as Sustainable Flame Retardants for Polymer Materials
PublikacjaDevelopment of green flame retardants has become a core part of the attention of material scientists and technologists in a paradigm shift from general purpose to specific sustainable products. This work is the first report on the use of coffee biowastes as sustainable flame retardants for epoxy, as a typical highly flammable polymer. We used spent coffee grounds (SCG) as well as SCG chemically modified with phosphorus (P-SCG)...
-
Surface sliding in human abdominal wall numerical models: Comparison of single-surface and multi-surface composites
PublikacjaDetermining mechanical properties of abdominal soft tissues requires a coupled experimental-numerical study, but first an appropriate numerical model needs to be built. Precise modeling of human abdominal wall mechanics is difficult because of its complicated multi-layer composition and large variation between specimens. There are several approaches concerning simplification of numerical models, but it is unclear how far one could...
-
Investigation of solid polymer electrolyte gas sensor with different electrochemical techniques
PublikacjaIn this work solid polymer electrolyte (SPE) amperometric sulphur dioxide sensor is investigated. Nafion was used as a membrane electrode and 1M sulphuric acid as an internal electrolyte. Sensor response to sulphur dioxide was measured. Besides traditional constant voltage amperometry also different electrochemical techniques were used. Results obtained by these methods are compared.
-
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publikacja -
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublikacjaThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...
-
Investigation of energy deposition and its optical imaging in polymer gel dosimeters
PublikacjaThis following chapter describes methods for verifying the absorbed dose during radiotherapy. Special attention is paid to the method using polymer-gel dosimeters, the dose reading of which is performed by means of Laser Computed Tomography. The chapter also includes considerations on alternative solutions for dosimetric measurements and various types of radiotherapy and their pros and cons. In addition, both the methods of structural...
-
The influence of temperature on properties of the polymer flexible joint used for strengthening historical masonries
PublikacjaA new method of repairing damaged structures by filling the cracks with a specially prepared elastomeric polymer mass has been recently proposed. This new and innovative technique, known as the Flexible Joint Method (FJM), is mainly dedicated to masonries and historical objects, where minimum intervention is permitted. The flexible joint bonds the disrupted elements and ensures further safe exploitation of a damaged structure....
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublikacjaThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
Interferometric Sensor of Wavelength Detuning Using a Liquid Crystalline Polymer Waveplate
PublikacjaOperation of a polarization interferometer for measurement of the wavelength changes of a tunable semiconductor laser was investigated. A lambda/8 waveplate made from liquid crystalline polymer is placed in one of interferometers’ arms in order to generate two output signals in quadrature. Wavelength was measured with resolution of 2 pm in the wavelength range 628–635 nm. Drift of the interferometer, measured in the period of 500...
-
Polymer Chemistry
Czasopisma -
Study on polymer modified road asphalt mixture
PublikacjaThe formulation of ternary asphalt-additives blend composed of crumb rubber : low-density polyethylene (CR : LDPE) and crumb rubber : textile fiber (CR : TF) couples, and quaternary asphalt additives-blend composed of (CR : LDPE : TF) triplets on the virgin asphalt to optimize the asphalt basic and rheological properties and to use the extrusion process of two or three additives to obtain composite materials of them, as well as...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publikacjan this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublikacjaA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Potential applications of by-products from the coffee industry in polymer technology – Current state and perspectives
PublikacjaCoffee is one of the most popular beverages in the world, and its popularity is continuously growing, which can be expressed by almost doubling production over the last three decades. Cultivation, processing, roasting, and brewing coffee are known for many years. These processes generate significant amounts of by-products since coffee bean stands for around 50% of the coffee cherry. Therefore, considering the current pro-ecological...
-
Performance of acicular grindable thermocouples for temperature measurements at sliding contacts
PublikacjaThe present study investigates the performance of acicular grindable thermocouples based on a constantan wire / steel hollow cylinder construction. The experiments showed that the measuring junction electrical resistance, temperature–voltage characteristic, measuring junction rise time and signal noise standard deviation of the acicular thermocouples are comparable to those of conventional J-type thermocouples with bare wire diameter...
-
2D Mathematical Model of the Commutator Sliding Contact of an Electrical Machine
PublikacjaW artykule przedstawiono model matematyczny 2D komutatorowego zestyku ślizgowego z wieloma stopniami swobody. W modelu uwzględniono zmienne wymuszenia działające na szczotkę. Wymuszenia te są wynikiem falistości wirującego komutatora. Szczotka została zamodelowana jako system wielu mas, elementów sprężystych i tłumików rozłożonych w kierunku stycznym i promieniowym. Zamodelowano wszystkie oddziaływania lepkosprężyste pomiędzy komutatorem...
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublikacjaThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Highly stable organic–inorganic junction composed of hydrogenated titania nanotubes infiltrated by a conducting polymer
PublikacjaA poly(3,4-ethylenedioxythiophene) conducting polymer doped with poly(2-styrene sulfonate) (pEDOT:PSS) was efficiently electrodeposited on a layer composed of ordered titania nanotubes. TiO2 nanotubes were formed during an anodization process and, after calcinations, a layer was subjected to hydrogen plasma. Hydrogenation leads to Ti(III) formation, a decrease in resistance, and a huge increase of donor density when compared with...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublikacjaThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
Bulk-Surface Modification of Nanoparticles for Developing Highly-Crosslinked Polymer Nanocomposites
PublikacjaSurface modification of nanoparticles with functional molecules has become a routine method to compensate for diffusion-controlled crosslinking of thermoset polymer composites at late stages of crosslinking, while bulk modification has not carefully been discussed. In this work, a highly-crosslinked model polymer nanocomposite based on epoxy and surface-bulk functionalized magnetic nanoparticles (MNPs) was developed. MNPs were...
-
Imprinted polymer particles for iron uptake: Synthesis, characterization and analytical applications
Publikacja -
Research and applications of active bearings: A state-of-the-art review
Publikacja -
Unique performance aspects of PTFE-Lined thrust bearings
PublikacjaW pracy przedstawiono korzyści płynące z zastępowania tradycyjnych stopów łożyskowych przez warstwy ślizgowe wykonane z kompozytów na bazie PTFE. Kompozytowe warstwy ślizgowe są coraz częściej stosowane w dużych łożyskach hydrogeneratorów o pionowych wałach. W pracy omówiono także aspekty stosowania takich łożysk związane z ich charakterystycznymi cechami.
-
Operation of slide journal bearings in unsteady energetic description.
PublikacjaW artykule zaproponowano interpretację wartościującą działania, które (podobnie jak przedstawione mechanice klasycznej działania Hamiltona i Maupertiusa oraz działanie wynikające ze zmiany pędu ciała) jest rozpatrywane jako wielkość fizyczna o jednostce miary zwanej dżulosekundą [dżulsekunda]. Przedstawiono propozycję ilościowej interpretacji działania dowolnego poprzecznego łożyska ślizgowego, w którym zachodzą oddziaływania energetyczne...
-
Polyolefins, commercial and alternative routes toward the world’s most important polymer
Kursy OnlineThe course will consist of lectures followed by discussions. Based on the gained knowledge the Students will be asked to prepare in teams a short essay how to economically produce a selected polyolefin and how to introduce the new product into the market.
-
Porosity and shape of airborne wear microparticles generated by sliding contact between a low-metallic friction material and a cast iron
PublikacjaThe wear of brakes in transport vehicles is one of the main anthropogenic sources of airborne particulate matter in urban environments. The present study deals with the characterisation of airborne wear microparticles from a low-metallic friction material / cast iron pair used in car brakes. Particles were generated by a pin-on-disc machine in a sealed chamber at sliding velocity of 1.3 m/s and contact pressure of 1.5 MPa. They...
-
From polymer waste to potential main industrial products: Actual state of recycling and recovering
Publikacjalastics have become widely used materials in everyday life due to their special properties such as durability, easy processing, light-weight and low-cost of production. However, because of their stable and non-biodegradable nature, postconsumer plastics become an issue to the environment. The growing amounts of waste are generated, as plastic products are commonly used only once before disposal. The alternatives of practical techniques...
-
More than just a beer—the potential applications of by-products from beer manufacturing in polymer technology
PublikacjaBeer is the most popular alcoholic beverage in the world, and its popularity is continuously growing. Currently, global beer production is estimated at around 2 billion hectoliters. Nevertheless, the increasing production capacity implicates the rising issue of generated by-products—brewers’ spent grain, spent hops, spent yeast, and wastewater. They are generated in massive amounts, so having in mind the current pro-ecological...
-
COLLOID AND POLYMER SCIENCE
Czasopisma -
Journal of Polymer & Composites
Czasopisma -
POLYMER REACTION ENGINEERING
Czasopisma