Filtry
wszystkich: 1215
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: bearings%20fatigue
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublikacjaIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Effectiveness of a mathematical model in simulating nonlinear mechanical behaviour of a seismic isolation system made of polymeric bearings
PublikacjaThe present study was focused on determining the effectives of a nonlinear mathematical model in simulating complex mechanical behaviour of a seismic isolation system made of Polymeric Bearings. The proposed mathematical model defines the lateral force as a nonlinear function of the shear displacement and the deformation velocity. The effectiveness of the proposed mathematical model was verified by comparing the seismic response...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublikacjaHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
POSSIBILITY OF IDENTIFICATION OF TECHNICAL CONDITION OF BEARINGS FOR SELF-IGNITION ENGINES BY APPLICATION OF ACOUSTIC EMISSION AS A DIAGNOSTIC SIGNAL
PublikacjaThis paper presents the results of empirical studies where the acoustic emission (AE) method was applied to identify the technical condition of sliding surfaces of main and crank bearings for main diesel engines. The test results indicate that the measurements of the AE parameters allow the technical condition identification for bearings of this type. The results refer to the measurements of the parameters for AE generated in the...
-
Sliding bearings with sintered bronze bush lubricated by contaminated water with solid particles – Theoretical and experimental studies
PublikacjaSliding journal bearings lubricated with water coming directly from the environment are a solution used in shipbuilding, pumps and hydropower. However, the working fluid or surrounding water cannot always be filtered because of design limitations, which often causes the problem of premature wear of these sensitive bearings. The research conducted made it possible to assess the wear of sliding bearings lubricated with water containing...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship structures. Part I: pitting corrosion of ship structures.
PublikacjaThe paper is a literature survey focused on pitting corrosion and its influence on fatigue of ship and offshore steels. Mechanisms of short- and long-term pitting corrosion in marine environment have been described including pit nucleation and growth phases. Some models of pit growth versus time of exposure have been presented. Some factors which influence the pit growth have been discussed briefly.
-
Intelligent microbearing project with memory of stress-strain history
PublikacjaTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
LANGUAGE SPEECH AND HEARING SERVICES IN SCHOOLS
Czasopisma -
Journal of Speech, Language, and Hearing Research
Czasopisma -
Fatigue strength determination of ship structural joints. Part I - Analytical methods for determining fatigue strength of ship tructures
PublikacjaSpectacular accidents at sea which have happened for a few last years show that hull structures of contemporary sea-going ships are not perfect and must be systematically improved. Fatigue strength is one of the groups of strength problems which affect design of contemporary ship's structures and greatly contribute in their improvement process. In this paper several approaches to estimation of fatigue life of hull structural...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublikacjaIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
On the effectiveness of Ni alloy-bronze composite lattice structures used in slide bearings operated under heavy loads
Publikacja -
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublikacjaMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublikacjaThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
WATER LUBRICATED MAIN SHAFT BEAR INGS WITH THREE LAYER BUSH – MODERN SOLUTION FOR MARINE INDUSTRY
PublikacjaWater lubricated sliding bearings are increasingly popular in marine and hydro power industry. Such popularity is partly due to their simple construction which also means a relatively affordable price. Properly designed and installed water lubricated bearings may well last for over a decade. During the last decade their traditional range has been expanded with new, modern products like three layer bearing bush. The work presents...
-
Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed
PublikacjaAn aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self- generated squeeze-film pressure on the stability...
-
Aromatic Dendrimers Bearing 2,4,6-Triphenyl-1,3,5-triazine Cores and Their Photocatalytic Performance
Publikacja -
Fuzzy reasoning system design and assessment of load-bearing endoprostheses and their fabrication processes
PublikacjaZaproponowano piec zastosowan podejscia rozumowania rozmytego do rozwiazania problemów w dziedzinie biomechanikioraz inzynierii biomateriałów. Obejmuja one: (A) oszacowanie maksymalnych naprezen kontaktowych działajacych naendoproteze, (B) zaprojektowanie procesu spiekania dla otrzymania porowatego implantu, (C) opracowanie planu utleniania wcelu otrzymania struktury nanorurkowej na stopach Ti, (D) oraz (E) zaprojektowanie osadzania...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublikacjaThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublikacjaIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublikacjaIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublikacjaThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublikacjaIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Stability and load bearing capacity of a braced truss under upward wind loading
PublikacjaThe paper is focused on the numerical and experimental investigation of stability of a steel truss under upward wind loading. The structure was stiffened by elastic braces situated at the top and bottom chord. Usually the lateral (translational) brace stiffness is considered. However, the rotational stiffness of braces caused by interaction between torsional stiffness of the truss top chord and bending stiffness of the roof elements...
-
Common-Mode Voltage and Bearing Currents in PWM Inverters: Causes, Effects and Prevention
PublikacjaIn modern induction motor drives an increase of transistors' switching frequency and a decrease of switching times are the sources of some serious problems. The high dv/dt and the common mode voltage generated by the inverter PWM control results in the appearances of bearing currents, shaft voltages, motor terminal overvoltages, the decrease of motor efficiency, and electromagnetic interference. The aspects of common mode (CM)...
-
Iron(III)-selective materials based on a catechol-bearing amide for optical sensing
PublikacjaThe synthesis and ion-binding properties of a new amide L derived from 3,4-dihydroxybenzoic acid are described. Due to the presence of a catechol unit, the compound interacts selectively with iron(III) in organic solvent (dimethyl sulfoxide, DMSO) to produce a color change from pale yellow to green. The incorporation of the ligand L into polymeric matrices or its encapsulation into surfactant-based spheres enables analyte detection...
-
Improving the accuracy of bearing in active sonar with cylindrical array using spectrum estimation.
PublikacjaThe articles presents a method for improving the accuracy of bearing in multibeam sonar with a cylindrical array. Based on a known spatial spectrum estimation technique, the method has been successfully used in linear array systems. Its accuracy of bearing is satisfactory and ensures a relatively low computational effort. The article discusses certain simplifications and assumptions to adapt the spatial spectrum estimation technique...
-
THE SYNCHROSQUEEZING METHOD IN BEARING ESTIMATION OF STATIONARY SIGNALS FOR PASSIVE SONAR WITH TOWED ARRAY
PublikacjaIn this paper, a novel method of bearing estimation in a passive sonar system with a towed array is introduced. The classical approach of bearing estimation based on the spatial spectrum [1] is extended by using the synchrosqeezing method that is a part of the reassignment method introduced by Kodera et al. [2]. Using this method leads to a precise bearing estimation. The proposed method requires a relatively small amount of computation,...
-
New Generation of Water lubricated Foil bearing - Numerical Models and Experimental Verification
PublikacjaIn the paper a new idea of foil water lubricated bearing and methodology of hydrodynamic characteristics calculations is presented. To assesses the theoretical characteristics of these bearings two different computer models were built. First is structural model coupled with fluid model. It takes into account: fluid flow in the deformed fluid gap, specific design of bearing support and friction in bearing support. The second is...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Water-lubricated stern tube bearing - experimental and theoretical investigations of thermal effects
PublikacjaThe paper presents research results of thermal phenomena accompanying operation of a water-lubricated stern tube bearing with axial grooves. Experimental tests revealed, that intensity of forced axial flow has strong influence on bush temperature. Numerical simulations focused on investigation of the thermal phenomena under operation of water-lubricated journal bearing showed, that restricted axial flow promotes backflow of the...
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublikacjaThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
Modeling of bearing capacity of footings on sand within stochastic micro-polar hypoplasticity.
PublikacjaAnalizowano numerycznie efekt wstępnego rozkładu wskaźnika porowatości na wytrzymałość i strefy ścinania w problemach fundamentów na piasku w skali modelowej. Obliczenia wykonano przy zastosowaniu stochastycznej metody elementów skończonych i mikropolarnego modelu hipoplastycznego. Wskaźnik porowatości miał formę skorelowanych pól stochastycznych. Dodatkowo obliczono efekt skali dla 3 różnych szerokości fundamentów.
-
Digital hearing aid with time and spectral transposition.
PublikacjaNastępstwem uruchomienia w Polsce, prowadzonych na szeroką skalę, badań przesiewowych słuchu jest konieczność zaoferowania pomocy osobom cierpiącym na niedosłuch poprzez leczenie i protetykę słuchu. Tymczasem, aktualnie oferowane rozwiązania aparatów słuchowych nie są w stanie sprostać niektórym specjalistycznym potrzebom aparatowania, m. in.: najmłodszych dzieci, osób pracujących w hałasie, pilotów wojskowych oraz osób korzystających...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...
-
Waveguide model of the hearing aid earmold system
PublikacjaBackground The earmold system of the Behind-The-Ear hearing aid is an acoustic system that modifies the spectrum of the propagated sound waves. Improper selection of the earmold system may result in deterioration of sound quality and speech intelligibility. Computer modeling methods may be useful in the process of hearing aid fitting, allowing physician to examine various earmold system configurations and choose the optimum one...
-
Hearing aid operating in acoustical free field
PublikacjaAparatowanie bardzo małych dzieci (od 5 miesiąca życia) za pomocą standardowych protez słuchu natrafia na wiele trudności natury praktycznej. Dotyczy to procesu dopasowania aparatu słuchowego, czyli doboru jego ustawień stosownie do aktualnych charakterystyk ubytku słuchu dzieci. Tymczasem wczesne aparatowanie jest zagadnieniem o ogromnym zanczeniu dla rozwoju słuchu, mowy i ogólnej inteligencji dziecka. Referat prezentuje uzyskane...
-
Modeling of acoustics of hearing aid earmold systems
Publikacja -
Waveguide modeling as a tool for fitting a hearing aid
Publikacja -
Expert media approach to hearing aids fitting
PublikacjaW artykule zaprezentowano problematykę dopasowania protez słuchu. Przedstawiono system ekspercki, który pozwala na znalezienie charakterystyk aparatu słuchowego adekwatnego do uszkodzenia słuchu. System został oparty o metodę zbiorów przybliżonych i logikę rozmytą.
-
Internet-based automatic hearing assessment system
PublikacjaCelem referatu jest prezentacja systemu przesiewowego badania słuchu w oparciu o Internet. Wady słuchu stanowią jedną z najszybciej postępujących chorób we współczesnym społeczeństwie. W tym kontekście ważne staje się umożliwienie przeprowadzania masowych testów wykrywających ubytki słuchu. Przedstawiona aplikacja zawiera audiometryczny test tonalny, test ilustrowany dla dzieci oraz test rozumienia mowy w szumie. Po zakończeniu...
-
Speech recognition system for hearing impaired people.
PublikacjaPraca przedstawia wyniki badań z zakresu rozpoznawania mowy. Tworzony system wykorzystujący dane wizualne i akustyczne będzie ułatwiał trening poprawnego mówienia dla osób po operacji transplantacji ślimaka i innych osób wykazujących poważne uszkodzenia słuchu. Active Shape models zostały wykorzystane do wyznaczania parametrów wizualnych na podstawie analizy kształtu i ruchu ust w nagraniach wideo. Parametry akustyczne bazują na...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Loudness Scaling Tests in Hearing Problems Detection
PublikacjaThe number of people using portable audio players has increased significantly over the recent years. This implies the rise in the number of people having hearing loss problems. Therefore, there is a need to find appropriate procedures that simplify the process of the hearing problem detection. Investigations performed show that audiometric tests may not be sufficient to assess hearing in young people. Contrarily, the obtained results...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Fatigue Behaviour of Sintered Duplex Stainless Steel
Publikacja -
Forecasting of fatigue life of laser welded joints
PublikacjaW pracy przedstawiono podstawowe dane na temat stalowych paneli typu sandwich. Zaprezentowano wyniki testów zmęczeniowych elementarnych połączeń teowych spawanych laserowo. Omówiono szczegółowo te cechy, które mają istotny wpływ na statyczne i zmęczeniowe własności złącza. Na podstawie przedstawionych wyników badań zmęczeniowych elementarnych połączeń spawanych laserowo uzyskano krzywą projektową S-N dla jednego z pokazanych modeli...
-
Fatigue life of steel, laser welded panels
PublikacjaW publikacji przedstawiono zagadnienia dotyczące możliwości analizy trwałości zmęczeniowej stalowyxh paneli spawanych laserowo typu sandwich. Przedstawiono wyniki badań laboratoryjnych w skali naturalnej a także krzywe projektowe uzyskane na podstawie systematycznych badań połączeń elementarnych spawanych laserowo. Na podstawie przedstawionych i uogólnionych wyników pokazano propozycję metodyki szacowania trwałości zmęczeniowej...