Wyszukiwarka
Filtry
wszystkich: 1029
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LOW TEMPERATURE
-
Badania mieszanek mineralno-asfaltowych w niskiej temperaturze
PublikacjaW artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...
-
The effect of preliminary creep-strain on material behavior under LCF tension/compression and pure torsion regimes
PublikacjaThis paper presents the results of experimental tests of monotonic tension and torsion, creep-rupture and preliminary creep at 200C and 300C, as well as low-cycle fatigue of 2024 T3511 aluminum alloy. The fatigue process was conducted at room temperature for uniaxial tension/compression and torsion. The as-received material and pre-deformed material were also investigated during creep at elevated temperature. Basic monotonic,...
-
Self-supporting LSFO films for bolometers made with LTCC technology
PublikacjaOpisano metodę wytwarzania przewodzących, tlenkowych warstw ceramicznych tlenków lantanowo-strontowo żelazowych (LSFO) technologią low temperature co-fired ceramics (LTCC). Przedstawiono rezultaty pomiarów parametrów warstw pod kątem przydatności do produkcji detektorów IR.
-
QUASI-DISTRIBUTED NETWORK OF LOW-COHERENCE FIBER-OPTIC FABRY-PÉROT SENSORS WITH CAVITY LENGTH-BASED ADDRESSING
PublikacjaDistributed measurement often relies on sensor networks. In this paper, we present the construction of low coherent fiber-optic Fabry-Pérot sensors connected into a quasi-distributed network. We discuss the mechanism of spectrum modulation in this type of sensor and the constraints of assembly of such sensors in the network. Particular attention was paid to separate the signals from individual sensors, which can be achieved by...
-
Evaluation and application of data from road weather stations for winter maintenance management
PublikacjaThe paper presents the analysis of road weather data from meteorological stations located at the Polish national roads of Pomerania District during the impact of winter conditions. Presented issue is particularly important from the point of view the problem of winter maintenance and especially for prediction and assurance of quality of asphalt pavement surface ie. resistance to low temperature cracking or risk of glazed frost....
-
Fractographical quantitative analysis of EN-AW 2024 aluminum alloy after creep pre-strain and LCF loading
PublikacjaThis paper explores the applicability of a new damage parameter combining both fracture surface topography and loading features to estimate the fatigue lifetime under creep pre-strain and low-cycle fatigue loading. Fractures of EN-AW 2024 aluminum alloy caused by mixed creep and low-cycle fatigue loading are experimentally characterized and quantified via surface topography analysis. The specimens were preliminary damaged in a...
-
Three phase transient model of wet coal pyrolysis
PublikacjaA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
Effects of deviations from thermo-rheologically simple behavior of asphalt mixes in creep on developing of master curves of their stiffness modulus
PublikacjaThe paper presents the deviations from the thermo-rheologically simple behavior of asphalt mixes and their effects on the developing of master curves of stiffness modulus. Eleven different mixes were tested in three point bending test under constant load at temperatures –20°C, –10 °C and 0 °C, and in some cases at +10 °C. The test method was developed at the Gdansk University of Technology, Poland. The applied stress level was...
-
The Effect of Temperature on Wear Mechanism of the AlCrN Coated Components
Publikacja -
Temperature Dependence of the Dissociative Electron Attachment to 2-Thiothymine
Publikacja -
Effect of high pressure of selected bacteria at subzero temperature
PublikacjaCelem pracy było określenie przeżywalności wybranych bakterii gramdodatnich i gramujemnych poddanych działaniu podwyższonego ciśnienia w zakresie od 60 do 193 MPa w ujemnej temperaturze. Wrażliwość bakterii na zwiększone ciśnienie zależy od fazy wzrostu w jakiej się one znajdują. Z reguły bakterie gramdodatnie są bardziej odporne na ciśnienie niż bakterie gramujemne. Wykazano, że różnice w odporności pojawiają się nie tylko pomiędzy...
-
Machine Learning for Sensorless Temperature Estimation of a BLDC Motor
Publikacja -
High temperature corrosion resistance of porous hastelloy alloy
PublikacjaW pracy przedstawiono badania korozyjne stopu Hastelloy w wysokich temperaturach.
-
Influence of stack temperature on PEM fuel cell performance
PublikacjaW pracy przedstawiono wpływ temperatury stosu na wydajność ogniwa paliwowego typu PEM dla zadanego obciążenia. Badania ogniwa paliwowego przeprowadzono dla sześciu temperatur pracy stosu z zakresu od 30 oC do 65 oC. Dla najwyższej temperatury stosu, tj. 65 oC, wydajność pracy ogniwa paliwowego była najwyższa. Wraz ze wzrostem temperatury stosu zarejestrowano spadek mocy ogniwa paliwowego od 1015 W dla temperatury 30 oC do 1004...
-
High temperature corrosion of the cobalt base clad layers
PublikacjaNapawane warstwy wykonane ze stopu kobaltu poddano utlenianiu w temperaturach 650 stopni C i 750 stopni C oraz korozji w spalinach. Proces utleniania był prowadzony 2 sposobami, izotermicznie przez 100 godzin i cyklicznie pzez 200 godzin. Korozja w spalinach przebiegała cyklicznie przez 200 godzin w temperaturze 650stopni C. Warstwy napawano metodą laserową i plazmową (PTA). Badano stabilność termiczną procesu utleniania warstw...
-
Simulation of temperature field in cylindrical boiling heating section
PublikacjaW pracy przedstawiono wyniki obliczeń cylindrycznej sekcji grzejnej. Biorąc pod uwagę geometrię i konstrukcję sekcji grzejnej zaprezentowano rozwiązania pola temperatury dla cylindrycznej sekcji grzejenej. W uzyskaniu rozwiązania posłużono się metodą elementów skończonych.
-
Ab initioheat capacity and atomic temperature factors of chalcopyrites
Publikacja -
The effect of temperature difference on heat transport in solar cells
PublikacjaW pracy omówiono wpływ wzrostu temperatury i mechanizm transportu ciepła na drodze przewodzenia w układach hybrydowych PV/T. Wyznaczono współczynniki przewodzenia krystalicznego krzemu typu n i p oraz gęstość strumienia ciepła w zakresie temperatur od 0 do 100 st. C.
-
White-light interferometric temperature sensor for biomedical diagnostic.
PublikacjaW artykule opisano opracowany model miniaturowego, światłowodowego czujnika temperatury z interferometrem Fabry-Perot wykorzystującego interferencję światła białego przeznaczonego do zastosowań biomedycznych. Analizowano czujnik wykonany ze światłowodu wielomodowego o skokowym profilu współczynnika załamania oraz ze światłowodu monomodowego. Zasadniczym celem był dobór parametrów mający na celu uzyskania maksymalnej widzialności...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublikacjaThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
TEMPERATURE INFLUENCE ON TIRE ROLLING RESISTANCE MEASUREMENTS QUALITY
PublikacjaGlobal warming makes it necessary to reduce energy consumption, which in the case of motor vehicles, is connected, among other things, with reduction of resistive forces acting on a vehicle during its motion. One of the most important components of those forces is rolling resistance, which is very difficult to measure, especially in road conditions. The article deals with issues related to the influence of the thermal state of...
-
Temperature modeling in activated sludge systems: a case study
PublikacjaPrzedstawiono model dynamiki temperatury jako część ogólnego modelu komory osadu czynnego. Transport ciepła opisano za pomocą jednowymiarowego równania adwekcyjno-dyspersyjnego z członem źródłowym opisującym teoretyczny bilans ciepła dla komory. Model został zweryfikowany w oczyszczalni ścieków Rock Creek w stanie Oregon (USA) w oparciu o dane eksploatacyjne oraz pomiary meteorologiczne z pobliskiej stacji meteorologicznej. Wyniki...
-
Photovoltaic maximum power point varying with illumination and temperature
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych zmian położenia punktu maksymalnej mocy na charakterystyce prądowo-napięciowej modułu ogniw fotowoltaicznych, związanych ze zmieniającą się temperaturą i natężeniem padającego promieniowania. Badano czas narastania napięcia pracy i temperatury ogniw w początkowej fazie ekspozycji na promieniowanie słoneczne. Przedstawiono niektóre praktyczne aspekty zastosowania układu automatycznego...
-
The gas corrosion of the cobalt base layer at elevated temperature
PublikacjaPrzedstawiono badania odporności na utlenianie i korozję w gorących gazach spalinowych napawanych laserowo warstw wykonanych ze stopu na bazie kobaltu.
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Determining the conditions for temperature measurements during flat lapping
PublikacjaPrzedstawiono pomiary temperatury układu wykonawczego docierarki jednotarczowej ABRALAP 380. Badano wpływ liczby stosowanych pierścieni prowadzących przy docieraniu elementów ceramicznych mikroziarnami węglika krzemu. Analizowano przyrost temperatury układu w czasie do trzech godzin. W badaniach zastosowano kamerę termowizyjną V-20II firmy VIGO System S.A.
-
Vacuum Rabi oscillation in nonzero-temperature open cavity
PublikacjaPorównania teorii oscylacji Rabiego z eksperymentem [M. Wilczewski, M. Czachor, Phys. Rev. A 79, 0333836 (2009)] sugerują, że parametry wnęki doświadczeniu z dużą ilością fotonów mogą być znacznie mniejsze niż te otrzymane dla stanów prawie próżniowych. W tym kontekście pokazujemy, że wniosek pozostaje bez zmian, nawet jeśli do opisu stanu początkowego wnęki zastosuje się bardziej realistyczny opis.
-
Speed dependency of temperature effects on road traffic noise
PublikacjaRecently, a new literature review on the influence of temperature on tire/road noise became available, based on a compilation of large amounts of data from empirical research. This review showed that the effect of temperature is roughly double of that previously assumed and taken account of in international standards. This makes temperature one of the main sources of error in measurement results. Furthermore, it suggested that...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
High Temperature Air Combustion and Gasification (HTAC; HTAG)
PublikacjaCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900oC provides additional energy in to conversion processes and results in considerable changes to the design of combustion and gasification...
-
High-temperature properties of titanium-substituted yttrium niobate
Publikacjahe defect fluorite titanium-doped yttrium niobate samples Y3Nb1−xTixO7−δ have been synthesized and investigated by the means of high-temperature X-ray diffraction, dilatometry, and thermogravimetry. Thermal expansion coefficients (TECs) as well as chemical expansion coefficients for material with 5, 10, and 15 mol% of titanium were determined. All investigated samples exhibit chemical contraction caused by Ti doping. The values...
-
High temperature corrosion resistance of porous hastelloy alloy
PublikacjaTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Changes of Conformation in Albumin with Temperature by Molecular Dynamics Simulations
PublikacjaThis work presents the analysis of the conformation of albumin in the temperature range of 300K – 312K, i.e., in the physiological range. Using molecular dynamics simulations, we calculate values of the backbone and dihedral angles for this molecule. We analyze the global dynamic properties of albumin treated as a chain. In this range of temperature, we study parameters of the molecule and the conformational entropy derived from...
-
Temperature Sensors Based on Polymer Fiber Optic Interferometer
PublikacjaTemperature measurements are of great importance in many fields of human activities, including industry, technology, and science. For example, obtaining a certain temperature value or a sudden change in it can be the primary control marker of a chemical process. Fiber optic sensors have remarkable properties giving a broad range of applications. They enable continuous real-time temperature control in difficult-to-reach areas, in...
-
High-Temperature Structural and Electrical Properties of BaLnCo2O6 Positrodes
PublikacjaThe application of double perovskite cobaltites BaLnCo2O6−δ (Ln = lanthanide element) in electrochemical devices for energy conversion requires control of their properties at operating conditions. This work presents a study of a series of BaLnCo2O6−δ (Ln = La, Pr, Nd) with a focus on the evolution of structural and electrical properties with temperature. Symmetry, oxygen non-stoichiometry, and cobalt valence state have been examined...
-
Temperature Fiber-Optic Sensor with ZnO ALD Coating
PublikacjaThis study presents a microsphere-based fiber-optic sensor with a ZnO Atomic Layer Deposition (ALD) coating thickness of 100 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100 °C to 300 °C, with a 10 °C step. An interferometric signal is used to control whether the microstructure is whole. Spectrum shift of a reflected signal is used to ascertain changes in...
-
Microsphere structure application for supercapacitor in situ temperature monitoring
PublikacjaConstant, real-time temperature monitoring of the supercapacitors for efficient energy usage is in high demand and seems to be crucial for further development of those elements. A fiber-optic sensor can be an effective optoelectronic device dedicated for in-situ temperature monitoring of supercapacitors. In this work, the application of the fiber-optic microstrucutre with thin zinc oxide (ZnO) coating fabricated in the atomic layer...
-
Internet system for supply and temperature control in server rooms
Publikacja.
-
Temperature influence on tyre/road noise frequency spectra
PublikacjaThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
High temperature drying of beech with content of tension wood
PublikacjaThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
A novel sensor for measuring temperature profile during the thermoablation
PublikacjaAbstract — A novel approach for monitoring a temperature distribution inside a tissue during thermoablation is presented in the paper. A thermal profile is measured using a set of serially connected thermistors each bypassed by a capacitor. This technique allows a two-wire and simultaneous multi- point measurements using a multi-frequency measurement of electrical impedance. It is...
-
Samonośne warstwy LSFO na bolometry wykonane technologią LTCC
PublikacjaOpisano sposób produkcji ceramicznych, przewodzących warstwtypu perowskitu z niestechiometrycznych tlenków lantanowo-strontowo żelazowych (LSFO) wykonanych technologią LTCC )low temperature co-fired ceramics). Zaprezentowano pomiary parametrów tych warstw, charakteryzujących ich przydatność do produkcji bolometrów.
-
Vibrational Properties of LaNb0.8M0.2O4-δ (M=As, Sb, V, and Ta)
PublikacjaLaNb0.8M0.2O4-δ (where M=As, Sb, V, and Ta) oxides with pentavalent elements of different ionic sizes were synthesized by a solid-state reaction method. The vibrational properties of these oxides have been investigated. These studies revealed that the substituent element influences both Debye temperature value as well as the Raman active vibrational modes. Additionally, the low-temperature vibrational properties of LaNb0.8Sb0.2O4-δ...
-
Gas sampling system for matrix of semiconductor gas sensors
PublikacjaSemiconductor gas sensors are popular commercial sensors applied in numerous gas detection systems. They are reliable, small, rugged and inexpensive. However, there are a few problem limiting the wider use of such sensors. Semiconductor gas sensor usually exhibits a low selectivity, low repeatability, drift of response, strong temperature and moisture influence on sensor properties. Sample flow rate is one of the parameters that...
-
The Characteristic of Surface Layers on Austenitic Stainless SteelAfter Glow-discharge Nitriding Process.
PublikacjaThis paper presents investigation of surface layers. The diffusion layers were produced by using different parameters of reactive atmosphere (N2:H2). The research of the surface layers was performed using scanning electron microscope (SEM). The results of energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD) analysis are presented. Research reveals the influence of chemical constitution of reactive atmosphere on the...
-
Rotational Molding of Linear Low-Density Polyethylene Composites Filled with Wheat Bran
PublikacjaApplication of lignocellulosic fillers in the manufacturing of wood polymer composites (WPCs) is a very popular trend of research, however it is still rarely observed in the case of rotational molding. The present study aimed to analyze the impact of wheat bran content (from 2.5 wt.% to 20 wt.%) on the performance of rotationally-molded composites based on a linear low-density polyethylene (LLDPE) matrix. Microscopic structure...
-
Improved energy management technique in pipe-embedded wall heating/cooling system in residential buildings
PublikacjaEffective and environmentally responsive techniques of energy management in residential buildings are desirable for the resulting reduction of energy costs and consumption. In this paper, an improved and efficient technique of energy management in pipe-embedded wall heating/cooling systems, called the Thermal Barrier, is described. Specifically, the Thermal Barrier is a technique focused on the management and control of heat...
-
Improved energy management technique in pipe-embedded wall heating/cooling system in residential buildings
PublikacjaEffective and environmentally responsive techniques of energy management in residential buildings are desirable for the resulting reduction of energy costs and consumption. In this paper, an improved and efficient technique of energy management in pipe-embedded wall heating/cooling systems, called the Thermal Barrier, is described. Specifically, the Thermal Barrier is a technique focused on the management and control of heat supply...
-
Experimental research on water lubricated marine stern tube bearings in conditions of improper lubrication and cooling causing rapid bush wear
PublikacjaWater lubricated bearings are popular in sliding bearings of marine propeller shafts, turbines and pump shafts. Such popularity is partly due to their simple construction which also means a relatively affordable price. In practical experience one may also observe cases of rapid wear or even malfunctions of this bearings, some of which may be caused by insufficient flow of lubricant leading to overheating. The conducted...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublikacjaMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...