Wyszukiwarka
Wyniki wyszukiwania dla: carbon steel
-
Comparison of Different Measurement Techniques as Methodology for Surveying and Monitoring Stainless Steel Chimneys
PublikacjaThe measurement of a chimney axis is an engineering geodesy task. These measurements allow to assess the technical condition of chimneys and are usually carried out for reinforced concrete chimneys. When measuring high chimneys, the main problem may be the need to go a long distance to take a measurement. The surface of the chimney can also be problematic because it can absorb so much light from the range finder that total station...
-
Effects of Column Base Flexibility on Seismic Response of Steel Moment-Frame Buildings
PublikacjaSteel Moment Resisting Frames (SMRFs) are very popular lateral load resisting systems in many seismically active regions. However, their seismic response is strongly dependent on the rotational fixity of column base connections. Despite many studies (both experimental and numerical) in this particular area, available approaches for estimating column base flexibility have been validated only against laboratory test data. In the...
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publikacja: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
Testing of the longest span soil-steel bridge in Europe – new quality in measurements
PublikacjaThe article describes interdisciplinary and comprehensive diagnostic tests of final bridge inspection and acceptance proposed for a soil – steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure response was collected. The load test design was based on the nonlinear numerical simulations performed by...
-
Friction-Induced Oscillations of a Non-Asbestos Organic Pin Sliding on a Steel Disc
PublikacjaFriction-induced oscillations result in deterioration of performance of disc brakes and are generally undesired. We conduct experimental study of friction-induced oscillations in a non-asbestos organic material / steel pair used in disc brakes of motor vehicles. The tests are done by use of a pin-on-disc machine which has the pin sample supported on a deformable beam. The adjustable friction parameters are the disc velocity, contact...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublikacjaKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Selection of Electrode Material for Inconel 617/P92 Steel SMAW Dissimilar Welds
PublikacjaThe present work aimed to investigate the microstructure and mechanical properties of the dissimilar shielded metal arc welded (SMAW) joint of Alloy 617 and P92 steel for advanced ultrasupercritical boilers. The SMAW joint was produced using three different types of electrodes, namely, ENiCrFe-3, ENiCrMo-3, and ENiCrCoMo-1. During microstructural observation of the welded joints, no possible cracking was detected in the weldments....
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublikacjaThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
Shaking table experimental study on models of steel buildings with different types of joints
PublikacjaThe aim of this paper is to study the response of models of steel buildings with destroyed and non-destroyed joints. The study was conducted experimentally using the shaking table tests. Two steel models were considered. Several types of joints were taken into account: totally destroyed joints, partially destroyed joints, welded joints and joints stiffened with additional metal. Six ground motions were taken into account. The acceleration...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublikacjaThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Weldability of Underwater Wet-Welded HSLA Steel: Effects of Electrode Hydrophobic Coatings
PublikacjaThe paper presents the effects of waterproof coatings use to cover electrodes on the weldability of high-strength, low-alloy (HSLA) steel in water. With the aim of improving the weldability of S460N HSLA steel in water, modifications of welding filler material were chosen. The surfaces of electrodes were covered by different hydrophobic substances. The aim of the controlled thermal severity (CTS) test was to check the influence...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Pyrolysis Process of Whole Waste Tires as a Biomass Energy Recycling
PublikacjaThe article is devoted to the description of material recycling of whole waste tires, including a new method of pyrolysis process, resulting in the final products: technically oil fractions (rubber plasticizer of rubber compounds) or diesel fuels (light, medium and heavy), activated carbon, gas fuel and steel scrap. Operational and performance tests of the first version of the pilot plant, consisting of three contributions cooperating...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublikacjaThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Wstępne badania technologii spawania złączy narożnych ze stali niskoweglowej i nierdzewnej o grubości g=6mm i g=10mm
PublikacjaCelem pracy był dobór parametrów spawania dla spoin narożnych o grubości 6mm i 10mm próbek wykonanych ze stali niskowęglowej S355 i stali nierdzewnej - typu 304 (X6CrNI18-10). Złącza były spawane laserowo, jednostronnie z pełnym przetopem a powierzchnie lica i grani zapewniają uzyskanie szczelności przylegającego elementu uszczelniającego. Próbki zostały dostarczone przez Zleceniodawcę. Próby zostały przeprowadzone na stanowisku...
-
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
Publikacja -
Seismic probabilistic assessment of steel and reinforced concrete structures including earthquake-induced pounding
PublikacjaRecent earthquakes demonstrate that prioritizing the retrofitting of buildings should be of the utmost importance for enhancing the seismic resilience and structural integrity of urban structures. To have a realistic results of the pounding effects in modeling process of retrofitting buildings, the present research provides seismic Probability Factors (PFs), which can be used for estimating collision effects without engaging in...
-
Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application
PublikacjaTo reduce costs and improve high-temperature performance in Advanced Ultra Super Critical (AUSC) boilers, it is necessary to weld austenitic steel to Inconel alloy. In this study, the autogenous tungsten inert gas (TIG) welding process was used to join Alloy 617 and an austenitic AISI 304H steel plate of thickness 5 mm. Microstructural analysis showed that the microstructure formation was uneven along the weldments, with columnar...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublikacjaThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
Response of cylindrical steel tank under stochastically generated non-uniform earthquake excitation
PublikacjaCylindrical steel tanks are very important structures in industrial facilities since their application is related to storing different types of products. Their safety and reliability have become a crucial issue because any damage may cause significant consequences, including ecological disaster. The most dangerous dynamic load acting on cylindrical steel tanks is related to earthquakes, especially that the seismic excitation may...
-
Application of mechanical Barkhausen noise in assessment of X20 steel properties after heat treatment
Publikacja -
Fatigue tests of steel Sandwich panel. Fifth International Conference on Marine Technology and Transportation.
PublikacjaW referacie przedstawiono wyniki badań laboratoryjnych paneli SANDWICH prowadzonych w Katedrze Technologii Okrętów, Systemów Jakości i Materiałoznawstwa Wydziału OiO na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów w wynikami prezentowanymi w literaturze.
-
Numerical calculations of wall pressures and stresses in steel cylindrical silos with concentric and eccentric hoppers
PublikacjaArtykuł przedstawia numeryczną analize naprężeń w płaszczu silosa. Porównane zostały wyniki dla silosów o przepływie centrycznym i mimośrodowym.
-
Comparision of two numerical methods for buried steel culverts made of corrugated shell sheets.
PublikacjaW pracy omawia się dwie metody analizy statycznej obudowy tuneli i przepustów dużej średnicy. Pierwsza z nich, metoda sprężyn polega na modelowaniu ośrodka gruntowego radialnymi sprężynami reprezentującymi odkształcalność gruntu. Drugie podejście oparte jest na zastosowaniu metody elementów skończonych i programu SOFISTIC. W układzie obudowa - grunt obudowę modeluje się zwykłymi ramowymi elementami sprężystymi a otaczający...
-
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
PublikacjaThe purpose of this work was to determine the essence of the influence of the impact velocity (5, 7, and 9 m/s) on Hertzian stresses and the erosion mechanism of ferritic-pearlitic S355J2 steel. The investigations were carried out using a slurry pot tester. S355J2 steel showed a strong sensitivity to changes in impact velocity. A significant increase in erosion rate was observed at a velocity of 9 m/s. This increase was 5-fold...
-
Complementary study with magnetic and acoustic techniques of A336 steel damage state due to creep
PublikacjaBadano możliwość detekcji w sposób nieniszczący zmian w mikrostrukturze stali A336 poddanej próbie pełzania. Testowano dwie magnetyczne techniki (klasyczny efekt Barkhausena i emisję magnetoakustyczną) oraz dwie nowe techniki ultradźwiękowe (pomiar współczynnika elasto-akustycznego oraz dwójłomność akustyczną). Wykazano, iż wyniki badań akustycznych są komplementarne do wyników badań magnetycznych.
-
Specific risks for local stability and capacity of verticat doble - shell cylindrical steel tanks
PublikacjaOmówiono zagrożenia stateczności i nosności płaszczy zbiorników dwupłaszczowych wywołane przez: niefachowo prowadzoną próbę wodną, dużną różnicę temperatury podczas eksploatacji oraz nierównomierne osiadanie. W księdze konferncyjnej opublikowano dwustronicowe streszczenie referatów a na załączonej płycie referaty zamieszczone są w całości.
-
DEIS assessment of AISI 304 stainless steel dissolution process in conditions of intergranular corrosion
Publikacja -
Numerical Simulation of Temperature Field in Steel under Action of Electron Beam Heating Source
Publikacja -
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublikacjaThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Formulation of spectral truss element for guided waves damage detection in spatial steel trusses
PublikacjaW pracy przedstawiono sformułowanie wielowęzłowego elementu spektralnego oraz odpowiedniego schematu całkowania ukierunkowanego na problem propagacji fal w kratownicach przestrzennych o dowolnej geometrii. Zaproponowane podejście nie ogranicza liczby węzłów w elemencie kratowym. Porównawcze rozwiązania numeryczne przeprowadzono dla konstrukcji idealnej (w stanie nieuszkodzonym) oraz dlakonstrukcji z miejscową nieregularnością w...
-
Instantaneous impedance evaluation of dissolution of aisi 304 stainless steel during intergranular corrosion
PublikacjaCelem pracy było uzyskanie informacji dotyczących zróżnicowania parametrów elektrycznych uzyskanych na podstawie zarejestrowanych chwilowych widm impedancyjnych w zakresie aktywacji i reaktywacji roztwarzania wysokostopowej stali austenitycznej AISI podczas postępującego procesu korozji międzykrystalicznej. Badania prowadzono z wykorzystaniem dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). Pomiary wykonywano ''on-line''...
-
Experimental and numerical study on deformed steel columns subjected to impact load during earthquakes
PublikacjaThe soft-storey failure is one of the most typical types of damage observed in buildings during earthquakes. The failure of an upper soft storey of a structure results in large impact load acting on the lower floors and if the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of the whole building. The aim of the present paper is to investigate the dynamic behaviour...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes - experimental study
PublikacjaIt has been observed during major earthquakes that the so called soft-storey failure of an upper floor of a structure results in large impact load acting on structural members of the lower storeys. It may further lead to progressive collapse of the whole structure substantially intensifying human and material losses. The aim of this paper is to investigate experimentally the behaviour of horizontally deformed columns (deformation...
-
Behaviour of deformed steel columns exposed to impact load during earthquakes: numerical analysis
PublikacjaIt has been observed during earthquakes that the so called soft-storey failure of an upper floor of a building leads to considerable vertical impact load acting on structural members of the lower storeys. The aim of this paper is to investigate numerically the behaviour of horizontally deformed columns (deformation as the result of earthquake loading) that are additionally subjected to vertical impact load. In the first stage of...
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
The buckling analysis of a cold-formed steel C-sectional column resting on an elastic foundation
PublikacjaThe paper is focused on stability analysis of different models of steel cold-formed C-section column. The analysed element may be applied as a primary load-bearing member in steel trusses or silo columns. The column can be used as a support for a wall of roof plates made of corrugated sheets. The wall sheeting that restrains the column against buckling may be considered as an elastic foundation. Due to the design solutions the...
-
Concept of cavitation erosion assessment of austenitic 1.4301 stainless steel based on roughness development
Publikacja -
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublikacjaThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublikacjaAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
Numerical Evaluation of Dynamic Response of a Steel Structure Model under Various Seismic Excitations
PublikacjaThe present paper reports the results of the study, which was designed to perform a numerical evaluation of dynamic response of a single-storey steel structure model. The experimental model was previously subjected to a number of different earthquake ground motions during an extensive shaking table investigation. The analyzed structure model was considered as a 1-DOF system with lumped parameters, which were determined by conducting...
-
Prediction of the Mechanical Properties of P91 Steel by Means of Magneto-acoustic Emission and Acoustic Birefringence
PublikacjaThe paper describes an application of nondestructive volumetric magnetic and ultrasonic techniques for evaluation of the selected mechanical parameter variations of P91 steel having direct influence on its suitability for further use in critical components used in power plants. Two different types of deformation processes were carried out. First, a series of the P91 steel specimens was subjected to creep and second, one to plastic...
-
Determination of Complex Permeability of Silicon Steel for Use in High-Frequency Modeling of Power Transformers
Publikacja -
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
Publikacja -
Stainless Steels Sintered Form the Mixture of Prealloyed Stainless Steel and Alloying Element Powders
Publikacja -
Influence of H2S on degradation of 9Cr-1Mo steel in advanced stage of metal dusting process
PublikacjaPrzedstawiono wyniki badań stali 9Cr-1Mo w zaawansowanym stadium procesu pylenia metalu po 10 latach eksploatacji w piecu rafineryjnej instalacji platformingu CCR, przeprowadzonych w celu podjęcia decyzji o dozowaniu związków siarki do wsadu instalacji. Na podstawie długotrwałej ekspozycji próbek stali w 600C w mieszaninie wodoru i siarkowodoru wykazano, że siarka może być powodem procesów wpływających niekorzystnie na stan materiału...
-
Use of electrochemical methods to examine different surface preparation methods for organic coatings on steel
PublikacjaObróbka strumieniowo - ścierna jest jedną z powszechnie stosowanych metod przygotowania powierzchni. Wśród nowoczesnych metod coraz większe zainteresowanie wzbudza przygotowanie powierzchni wodą pod wysokim ciśnieniem (z ang. waterjetting). W porównaniu z konwencjonalnymi metodami ''waterjetting'' jest nowoczesną oraz przyjazną środowisku metodą. W literaturze brakuje informacji na temat skuteczności owej metody do zastosowań...
-
Tool Life and Process Dynamics in High Speed Ball End Milling of Hardened Steel
Publikacja -
Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production
Publikacja