Wyszukiwarka
Wyniki wyszukiwania dla: method configuration
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublikacjaIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
A Simple-Topology Compact Broadband Circularly Polarized Antenna With Unidirectional Radiation Pattern
PublikacjaIn this letter, a geometrically simple, reflector-backed single-point-fed circularly polarized (CP) antenna with unidirectional radiation pattern is presented. The structure comprises a simple coplanar waveguide (CPW) feeding circuit with an open slot etched on one side of the coplanar ground. The enhanced CP bandwidth is obtained by combining the loop mode, the slot mode, and the asymmetrical configuration of the coplanar ground...
-
High load capacity spur gears with conchoidal path of contact
PublikacjaThe present study is devoted to investigation of spur gears with a conchoidal path of contact and a convex-convex contact between teeth. The load capacity and energy efficiency were evaluated using both theoretical and experimental approaches. The theoretical analysis showed that the conchoidal gear pairs are 5–21% stronger in terms of contact stress and have similar energy efficiency as compared to the involute gear pairs of the...
-
Minichannel and minigap classification criteria based on the aspect ratio of the minigeometry: A numerical study
PublikacjaA detailed numerical investigation has been carried out to analyze the diabatic flow distribution and velocity profile in 18 minigeometries with various aspect ratios for V-type and I-type flow configurations (for 36 cases) assuming ethanol as a working fluid. The aim of the study is to distinguish the value of the aspect ratio for which the flow in minigeometry starts to be two-dimensional (minigap). Cases with a constant Reynolds...
-
Simulations of wave propagation and attenuation in fields of colliding ice floes
Dane BadawczeThis dataset contains results of numerical smulations of sea ice-wave interactions, corresponding to laboratory experiments conducted at the Large Ice Model Basin (LIMB) at the Hamburg Ship Model Basin (HSVA) as part of the LS-WICE ("Loads on Structure and Waves in Ice"; https://zenodo.org/record/1067170#.XrLt_dhpxhE) project. THe simulations were conducted...
-
Performance Analysis of Multicast Video Streaming in IEEE 802.11 b/g/n Testbed Environment
PublikacjaThe aim of the work is to analyse capabilities and limitations of different IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both multicast and unicast video streaming transmissions directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
The role of SSVF and SSHF beds in concentrated wastewater treatment, design recommendation
PublikacjaThe return flows of reject water from sewage sludge dewatering alter the activated sludgeprocess in a conventional WWTP and increas TN concentration in final effluent from WWTPs.The objectives of the investigation carried out is to consider the application of sequential SS VFbeds and an SS HF bed for the treatment of highly polluted wastewater, namely reject waterfrom sewage sludge dewatering in a centrifuge (RWC). This paper aims...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublikacjaThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Cascaded Buck Hybrid Interlink Converter for Multiple-Input / Multiple-Output Operation
PublikacjaThe provision of isolated- and non-isolated DC output voltages by Power electronics power-conditioning devices in the recent ‘green-energy-revolution’ era is on course. In this paper, a structure for multi-input multi-output(MIMO) DC–DC buck converter is proposed to generate output voltages of varying levels with fewer component-count. The DC output voltage of each of the constituting buck converters can be used independently or...
-
Electron Scattering from Methyl Formate (HCOOCH3): A Joint Theoretical and Experimental Study
PublikacjaElastic low-energy electron collisions with methyl formate have been studied theoretically at the level of various theories. The elastic integral cross section was calculated using Schwinger multichannel and R-matrix methods, in the static-exchange and static-exchange plus polarization levels of approximations for energies up to 15 eV. The absolute total cross section for electron scattering from methyl formate has been measured...
-
The Way One Defines Specification Matters: On the Performance Criteria for Efficient Antenna Optimization in Aggregated Bi-Objective Setups
PublikacjaDesign of antenna structures for real-world applications is a challenging task that often involves addressing multiple design requirements at a time. Popular solution approaches to this class of problems include utilization of composite objectives. Although configuration of such functions has a significant effect on the cost and performance of the optimization, their specific structure is normally determined based on engineering...
-
Canonical switched capacitor converters. Comments, complements, and refinements
PublikacjaSwitched Capacitor Converters (SCC) form useful blocks in low/medium power applications as they are suitable for integration, both as off-chip and on-chip IC realizations. However, the problem with SCC is that their voltage conversion ratio is topology-dependent. By changing the SC circuit configuration, we can gain control over voltage conversion but the available ratio remains of a discrete nature, i.e. it maps into a countable...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublikacjaBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Direction-of-Arrival Estimation Methods in Interferometric Echo Sounding
PublikacjaNowadays, there are two leading sea sounding technologies: the multibeam echo sounder and the multiphase echo sounder (also known as phase-dierence side scan sonar or bathymetric side scan sonar). Both solutions have their advantages and disadvantages, and they can be perceived as complementary to each other. The article reviews the development of interferometric echo sounding array configurations and the various methods applied...
-
Analysis of IPv6 Handovers in IEEE 802.16 environment
PublikacjaZaprezentowano pełną analizę wpływu poszczególnych faz procesu przełączania w warstwie drugiej i trzeciej na przerwy w transmisji wynikające ze zmiany stacji bazowej BS przez przemieszczający się węzeł ruchomy MN. Zaproponowano i przebadano symulacyjnie 10 scenariuszy przełączania, w tym 8 różnych algorytmów stanowej autokonfiguracji węzłów MN, wspierających protokół IPv6 w środowiskach sieci WiMAX. W badaniach wskazano na możliwości...
-
Areas of updraft air motion from WRF model simulations.
Dane BadawczePresented dataset is a part of numerical modelling study focusing on the analysis of sea ice floes size distribution (FSD) influence on the horizontal and vertical structure of convection in the atmosphere. The total area and spatial arrangement of the updrafts indicates that the FSD affects the total moisture content and the values of area averaged...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublikacjaThe aim of the paper is to analyze data obtain during sounding of the Gdansk Bay by means of the parametric sonar. The accuracy of the sea bottom structure investigation needs the correct configuration of research equipment and the proper calibration of peripheral devices (GPS, heading sensor, motion sensor MRU-Z and navigation units) which provide necessary data to bathymetrical measurement system enabling its work with whole...
-
The concept of sewage-sludge management system for an individual household
PublikacjaThe individual farms at the rural areas often face problems with domestic sewage collection and treatment. In many cases building of sewerage systems and central wastewater treatment plants (WWTPs) brings too high costs, due to high distances from one farm to another and terrain configuration. Treatment wetlands for individual farms can solve this problem. In the article, an overview of individual treatment wetlands in Europe and...
-
Operation of multistage constructed wetlands systems in temporary climate
PublikacjaThe investigation were carried out at two different hybrid constructed wetlands, which treated municipal sewage after mechanical treatment from small villages in Pomeranian Region. In all facilities first step of biological treatment were horizontal flow beds. The main difference concern configuration of the facilities and sewage distributions systems into vertical flow beds. The measurement period was divided into vegetation...
-
Process zone in the Single Cantilever Beam under transverse loading. - Part II: Experimental
PublikacjaThis paper describes an experimental arrangement to evaluate stress/strain fields in the process zone of asymmetric adhesively bonded joints. A transparent polycarbonate flexible beam was bonded to an aluminium alloy rigid block with an epoxy adhesive in a Single Cantilever Beam (SCB) configuration. The flexible adherend was loaded in the direction parallel to the initial crack front at constant rate. To monitor strains induced...
-
New Polymeric Materials for Solid Phase Extraction
PublikacjaSolid phase extraction (SPE) is a popular sample preparation technique, which can be applied directly in gas–solid phase and liquid–solid phase, or indirectly to solid samples by using, e.g., thermodesorption with subsequent chromatographic analysis. Although SPE can be described as a physical extraction process involving a liquid phase and a solid phase, the increased use of packed sorbent formats seems to have led to a bias toward...
-
Code development of a DSP-FPGA based control platform for power electronics applications
PublikacjaThis paper focuses on the implementation of power electronics algorithms in control platforms based on DSP-FPGA. Today’s power electronics technology demands high power computation with high speed interfacing at the same time. The most popular configuration is a DSP for the former and a FPGA for the latter. The main goal of this work was to develop a generic control system for power electronics application, but it is explained...
-
The excitation controller with gain scheduling mechanism for synchronous generator control
PublikacjaThe power systems, including the synchronous generators and power systems networks, are complex nonlinear systems with configuration and parameters which change through time. That leads to electromechanical oscillations occurring in that system. Thus synchronous generator excitation controller must be capable of providing appropriate stabilization signal over broad range of operating conditions and disturbances. In this paper,...
-
Processing data on sea bottom structure obtained by means of the parametric sounding
PublikacjaThe aim of the paper is to analyze data obtained during sounding the Gdansk Bay sea bed by means of the parametric echo-sounder. The accuracy of the sea bottom structure investigation needs correct configuration of research equipment and proper calibration of peripheral devices (GPS, heading sensor, MRU-Z motion sensor and navigation instruments which provide necessary data to bathymetrical measurement system, enabling its work...
-
A new anisotropic bending model for nonlinear shells: Comparison with existing models and isogeometric finite element implementation
PublikacjaA new nonlinear hyperelastic bending model for shells formulated directly in surface form is presented, and compared to four existing prominent bending models. Through an essential set of elementary nonlinear bending test cases, the membrane and bending stresses of each model are examined analytically. Only the proposed bending model passes all the test cases, while the other bending models either fail or only pass the test cases for...
-
Collision Strengths of Astrophysical Interest for Multiply Charged Ions
PublikacjaThe electron impact excitation and ionization processes are crucial for modeling the spectra of different astrophysical objects, from atmospheres of late-type stars to remnants of supernovae and up to the light emission from neutron star mergers, to name just a few. Despite their signifi- cance, however, little is known quantitatively about these processes for low- and medium-impact energies of, say, Ekin . 5000 eV of the free...
-
Preparation and Characterization of Microsphere ZnO ALD Coating Dedicated for the Fiber-Optic Refractive Index Sensor
PublikacjaWe report the fabrication of a novel fiber-optic sensor device, based on the use of a microsphere conformally coated with a thin layer of zinc oxide (ZnO) by atomic layer deposition (ALD), and its use as a refractive index sensor. The microsphere was prepared on the tip of a single-mode optical fiber, on which a conformal ZnO thin film of 200 nm was deposited using an ALD process based on diethyl zinc (DEZ) and water at 100 °C....
-
Circular polarization diversity implementation for correlation reduction in wideband low-cost multiple-input-multiple-output antenna
PublikacjaIn this paper, a multiple-input-multiple-output (MIMO) antenna featuring circular polarization diversity, and designed on a common coplanar ground is presented. The proposed antenna design utilizes a coplanar waveguide (CPW) feeding technique with three parallel coplanar ground planes, and two feedlines in-between. For circular polarization (CP), quasi-loops are created by etching slots on the outermost ground planes. With this...
-
Artificial Intelligence Technologies in Education: Benefits, Challenges and Strategies of Implementation
PublikacjaSince the education sector is associated with highly dynamic business environments which are controlled and maintained by information systems, recent technological advancements and the increasing pace of adopting artificial intelligence (AI) technologies constitute a need to identify and analyze the issues regarding their implementation in education sector. However, a study of the contemporary literature reveled that relatively...
-
Optimizing FSO networks resilient to adverse weather conditions by means of enhanced uncertainty sets
PublikacjaThis work deals with dimensioning of wireless mesh networks (WMN) composed of FSO (free space optics) links. Although FSO links realize broadband transmission at low cost, their drawback is sensitivity to adverse weather conditions causing transmission degradation on multiple links. Hence, designing such FSO networks requires an optimization model to find the cheapest configuration of link capacities that will be able to carry...
-
Ipertrofan Revisited—The Proposal of the Complete Stereochemistry of Mepartricin A and B
PublikacjaBeing a methyl ester of partricin, the mepartricin complex is the active substance of a drug called Ipertrofan (Tricandil), which was proven to be useful in treatment of benign prostatic hyperplasia and chronic nonbacterial prostatitis/chronic pelvic pain syndrome. Nevertheless, no direct structural evidence on the stereochemistry of its components has been presented to date. In this contribution, we have conducted detailed, NMR-driven...
-
Usage of parametric echosounder with emphasis on buried object searching.
PublikacjaThe purpose of this article is to present the results of investigation to search for buried objects. The paper will contain echograms and other means of visualization from buried pipe placed between area of W?adys?awowo and gas platform and interesting in terms of the number of small and medium-sized unidentified objects found in the muddy bottom at different depths localized in the Gulf of Puck - results will be presented also...
-
The influence of feed rate and shear forces on the devulcanization process of ground tire rubber (GTR) conducted in a co-rotating twin screw extruder
PublikacjaThe search for new ways to recycling of rubber waste has been the aim of many studies conducted by research centers and companiesworldwide. The results of our investigations on the process of continuous thermomechanical devulcanization of ground tire rubber using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear...
-
A Series-Inclined-Slot-Fed Circularly Polarized Antenna for 5G 28-GHz Applications
PublikacjaThis letter presents the design of a single-point-fed, geometrically simple circularly polarized (CP) antenna for 28 GHz Ka-band applications. The proposed antenna is based on a straight microstrip line printed on one side and coupled with the nearly square patches through a 45-degree inclined V-shape slot aperture on the other side. In order to generate circular polarization, the fundamental radiating mode is degenerated at a...
-
Static and Dynamic Mechanical Properties of 3D Printed ABS as a Function of Raster Angle
PublikacjaDue to the rapid growth of 3D printing popularity, including fused deposition modeling (FDM), as one of the most common technologies, the proper understanding of the process and influence of its parameters on resulting products is crucial for its development. One of the most crucial parameters of FDM printing is the raster angle and mutual arrangement of the following filament layers. Presented research work aims to evaluate different...
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublikacjaThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
The conducted immunity test of a power supply unit in accordance with EMC standards
Dane BadawczeThe dataset presents a result of measurements that are a part of immunity tests to conducted disturbances, induced by radio-frequency fields. The immunity tests were carried out on the mains cable of the DF1723003TC NDN power supply. Tests of immunity of electronic systems to conducted disturbances in the frequency range from 150 kHz to 230 MHz are...
-
A review on gasification and pyrolysis of waste plastics
PublikacjaGasification and pyrolysis are thermal processes for converting carbonaceous substances into tar, ash, coke, char, and gas. Pyrolysis produces products such as char, tar, and gas, while gasification transforms carbon-containing products (e.g., the products from pyrolysis) into a primarily gaseous product. The composition of the products and their relative quantities are highly dependent on the configuration of the overall process...
-
Evaluation of respiration capacity of VF in hybrid constructed wetland systems.
PublikacjaThree VF-beds operating in hybrid constructed wetlands in configuration HF-VF-HF were analysed. These hybrid constructed wetlands provide the II stage biological treatment. They are located in Pommerania voivodship, in Sarbsk, Wiklino and Wieszyno, and their capacities are 29.5, 14.2 and 21.6 m3/d, respectively. The article focuses on performance and operation of VF-CW plants during one year. Based on removal of organic matter...
-
Static Shunt PE Voltage-Quality Controllers
PublikacjaThis chapter focuses on power electronics (PE)-based solutions used in distribution networks for reduction of supply-voltage-quality deterioration, from long interruptions to the harmonics. Various PE devices and their combinations are addressed for particular or a range of voltage disturbances. A particular solution is applied taking into account demands for voltage quality and network configuration. In general, there are three...
-
HILS for the Design of Three-Wheeled Mobile Platform Motion Surveillance System with a Use of Energy Performance Index
PublikacjaCurrent tendency in mechatronic design requires the use of comprehensive development of an environment, which gives the possibility to prototype, design, simulate and integrate with dedicated hardware. The paper discusses the Hardware-In-the-Loop Simulations (HILS) mechatronic technique, used during the design of the surveillance system based on energy performance index. The presented test configuration (physical controller – emulated...
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublikacjaIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
Multisensor System for the Protection of Critical Infrastructure of Seaport
PublikacjaThere are many separated infrastructural objects within a harbor area that may be considered “critical”, such as gas and oil terminals or anchored naval vessels. Those objects require special protection, including security systems capable of monitoring both surface and underwater areas, because an intrusion into the protected area may be attempted using small surface vehicles (boats, kayaks, rafts, floating devices with weapons...
-
Semicrystalline Polyesters Based on a Novel Renewable Building Block
PublikacjaIsohexides, like e.g. isosorbide, are well-known carbohydrate-based rigid diols which are capable of dramatically increasing the glass transition temperature of polyesters. However, their relatively low reactivity has thus far hampered large-scale industrial applications in the polymer field. Recently, with the aim to increase reactivity while at the same time retain rigidity, we have developed a new isoidide dicarboxylic acid...
-
Operational Performance and Weld Bead Characteristics of Experimental Tubular-Wires for Underwater Welding
PublikacjaAiming to evaluate new formulations and their operational behavior underwater, two experimental tubular wires with different chemical compositions in their internal flux were initially manufactured, employing a pilot machine and a unique manufacturing process. Weld beads were deposited on a plate placed in a flat position inside a tank using a mechanized system and the IMC 300 welding power source. The work was done at a depth...
-
Proton conductivity in multi-component ABO4-type oxides
PublikacjaThis work investigates how configurational entropy in oxides could affect proton conductivity. For this purpose, three samples of different elemental compositions are synthesized. Five, six and seven elements were introduced into the A-site of ANbO4, forming La1/5 Nd1/5 Sm1/5Gd1/5 Eu1/5NbO4, La1/6Nd1/6Sm1/6Gd1/6Eu1/6Ho1/6NbO4 and La1/7Nd1/7Sm1/7Gd1/7Eu1/7Ho1/7Er1/7NbO4, respectively. The high configuration disorder changes the...
-
Insightful studies of AuCu nanostructures deposited on Ti platform: Effect of rapid thermal annealing on photoelectrochemical activity supported by synchrotron radiation studies
PublikacjaIn this work, we present the influence of annealing atmospheres during rapid thermal annealing (40◦C/s) on nanostructured Ti platforms modified by 10 nm layer of AuCu alloy obtained via magnetron sputtering. The AuCu/Ti platform annealed under hydrogen atmosphere exhibits the best photoelectrochemical activity under visible light, i.e. 27 times higher photocurrent than for pure Ti dimpled platform, and the lowest reflectance with minimum...
-
Chiral analysis of chloro intermediates of methylamphetamine by one-dimensional and multidementional NMR and GC/MS
PublikacjaImpurity profiling and classification of abused drugs using chiral analytical techniques is of particular interest and importance because of the additional information obtained fromthis approach. When these methods are applied to the synthesis of illicitly used substances, they can supply valuable information about the conditions/chemicals used in the synthesis. We have applied GC and NMR methods to the study of intermediates found...