Wyszukiwarka
Wyniki wyszukiwania dla: process performance
-
Effect of iron oxides scaling on the MD process performance
Publikacja -
Simultaneous Removal of Hexane and Ethanol from Air in a Biotrickling Filter—Process Performance and Monitoring Using Electronic Nose
PublikacjaBiofiltration is a well-accepted method for the removal of malodorous compounds from air streams. Interestingly, the mechanisms underlying this process are not fully understood. The aim of this paper was to investigate the simultaneous removal of hydrophobic hexane with hydrophilic ethanol, resulting in the enhanced removal of hexane in the presence of ethanol. Investigations were performed in a peat-perlite packed biotrickling...
-
Evaluation of Partial Nitritation/Anammox (PN/A) Process Performance and Microorganisms Community Composition under Different C/N Ratio
PublikacjaA one-stage partial nitritation/anammox (PN/A) process with intermittent aeration is possible under sidestream conditions, but implementation in a mainstream is a challenge due to increased Carbon/Nitrogen (C/N) ratios in domestic wastewater. This study investigated the effect of C/N ratios on process efficiency and the effect of narrowing non-aeration time on process improvement at high chemical oxygen demand (COD) load. An increase...
-
Long-term performance of membrane distillation process
Publikacja -
Influence of polypropylene membrane surface porosity on the performance of membrane distillation process
Publikacja -
Effect of the Cavitation Generation Unit Structure on the Performance of an Advanced Hydrodynamic Cavitation Reactor for Process Intensifications
PublikacjaThe advanced rotational hydrodynamic cavitation reactors (ARHCRs) that appeared recently have shown obvious advantages compared with conventional devices in process intensifications. In ARHCRs, the cavitation generation unit (CGU) located on the rotor and stator basically determines their performance. For the first time, the present study investigated the effect of the CGU structure on the performance of a representative ARHCR...
-
Investigation into MPI All-Reduce Performance in a Distributed Cluster with Consideration of Imbalanced Process Arrival Patterns
PublikacjaThe paper presents an evaluation of all-reduce collective MPI algorithms for an environment based on a geographically-distributed compute cluster. The testbed was split into two sites: CI TASK in Gdansk University of Technology and ICM in University of Warsaw, located about 300 km from each other, both connected by a fast optical fiber Ethernet-based 100 Gbps network (900 km part of the PIONIER backbone). Each site hosted a set...
-
High-performance liquid chromatography in group-type separation and technical or process analytics of petroleum products
PublikacjaW pracy dokonano przeglądu i poddano krytycznej ocenie metody oznaczania składu grupowego produktów naftowych o różnej lotności, zarówno metody znormalizowane, jak i opisane w literaturze naukowej. W zdecydowanej większości są to metody wykorzystujące technikę chromatografii cieczowej w układzie faz normalnych (NP-HPLC). Na podstawie danych z literatury oraz własnych studiów i badań należy stwierdzić, że im wyższy zakres temperatury...
-
Thermal utilization of meat and bone meals. Performance analysis in terms of drying process, pyrolysis and kinetics of volatiles combustion
PublikacjaA development of technology of thermal utilization requires a thorough knowledge of the physicochemical properties, as well as kinetics of combustion of volatiles and char. Due to waste management regulations the meat and bone meal (MBM) is regarded as biofuel constituting one of the alternatives to fossil fuels in the energy market. MBM is a heterogeneous material that may consist of several different fractions. The extensive...
-
The Impact of Operational Parameters on Polypropylene Membrane Performance during the Separation of Oily Saline Wastewaters by the Membrane Distillation Process
Publikacja -
Process control of leakages in refinery reforming plant by means of Normal Phase High Performance Liquid Chromatography (HPLC)
PublikacjaPraca dotyczy zbadania możliwości, opracowania nowej procedury badawczej oraz dokonania oznaczeń ¬m-krezolu w strumieniu produktu z procesu reformingu katalitycznego techniką wysokosprawnej chromatografii cieczowej w układzie faz normalnych, z detektorem spektrofotometrycznym typu DAD (NP-HPLC-UV-VIS/DAD). Opracowana procedura stanowi alternatywę dla innych procedur wykorzystujących klasyczne techniki analityczne, albo wykorzystanie...
-
Removal of ketoprofen from surface water in a submerged photocatalytic membrane reactor utilizing membrane distillation: effect of process parameters and evaluation of long‐term performance
Publikacja -
Daniel Chuchała dr hab. inż.
Osoby -
MANAGING LEARNING PROCESS WITH E-LEARNING TOOL
PublikacjaThis article presents one possibility to employ Moodle, the free e-Leaning platform, to organize learning understood as a process. Behavioral approach and application to massive courses are assumed. A case study is presented, where the introduction of Moodle resulted in better student performance in homework
-
Evaluating the effectivness of an outsourced processes on the basis of key performance indicators
PublikacjaAccording to the statistics outsourcing has become typical solution for mature economies. Besides short run attempt based on cost reduction, getting popular is the method of increasing the effectiveness by implementing outsourced process. Authors in this article present the methods of measuring outsourcing performance on the basis of key performance indicators.
-
Improving all-reduce collective operations for imbalanced process arrival patterns
PublikacjaTwo new algorithms for the all-reduce operation optimized for imbalanced process arrival patterns (PAPs) are presented: (1) sorted linear tree, (2) pre-reduced ring as well as a new way of online PAP detection, including process arrival time estimations, and their distribution between cooperating processes was introduced. The idea, pseudo-code, implementation details, benchmark for performance evaluation and a real case example...
-
Company Culture, Knowledge Sharing and Organizational Performance. The Employee’s Perspective
PublikacjaKnowledge sharing, as a basic prerequisite for knowledge creation, is a dynamic social process characterized by profound human interactions. The process of knowledge sharing can be supported by organizational culture which is a set of values and norms giving identity to each enterprise. As a valuable element of intellectual capital, organizational culture contributes to achieving strategic business goals. The purpose of this article...
-
Thermodynamic modeling of combustion process of the internal combustion engines – an overview
PublikacjaThe mathematical description of combustion process in the internal combustion engines is a very difficult task, due to the variety of phenomena that occurring in the engine from the moment when the fuel-air mixture ignites up to the moment when intake and exhaust valves beginning open. Modeling of the combustion process plays an important role in the engine simulation, which allows to predict incylinder pressure during the combustion,...
-
Performance of ASON/GMPLS architecture in condition of wavelength conversion and without wavelength conversion
PublikacjaThe paper regards the problem of ASON/GMPLS performance in condition of wavelength and without wavelength conversion. The authors present influence analysis in condition of wavelength and non-wavelength conversion on the ASON/GMPLS control plane performance represented by mean Connection Set-up Time E (CST) and request loss probabilities. The offered traffic to the transport layer and request intensity have been changed for evaluation...
-
Market knowledge and new product performance: the mediating effects of new product performance
PublikacjaMarket knowledge is recognised as an important predictor of new product performance, which existing studies have proven. However, a missing link in this relationship is creativity, and specifically, as a natural process in product innovation. This study aims to examine a model that includes two mediating mechanisms between market knowledge scope and two new product outcomes, respectively: a new product’s competitive advantage and...
-
Maturity curve for estimating the in-place strength of high performance concrete
PublikacjaThe paper presents the maturity curve for estimating the in-place early-age compressive strength of concrete. The development of appropriate maturity curve is a complex process. It is important to correctly determine the datum temperature and activation energy, which can be obtained in mortar tests. This paper describes an investigation of the accuracy of the maturity method to estimate the strength when different way to rate constant...
-
Removal of Volatile Organic Compounds (VOCs) from Air: Focus on Biotrickling Filtration and Process Modeling
PublikacjaBiotrickling filtration is a well-established technology for the treatment of air polluted with odorous and volatile organic compounds (VOCs). Besides dozens of successful industrial applications of this technology, there are still gaps in a full understanding and description of the mechanisms of biotrickling filtration. This review focuses on recent research results on biotrickling filtration of air polluted with single and multiple...
-
Improving Clairvoyant: reduction algorithm resilient to imbalanced process arrival patterns
PublikacjaThe Clairvoyant algorithm proposed in “A novel MPI reduction algorithm resilient to imbalances in process arrival times” was analyzed, commented and improved. The comments concern handling certain edge cases in the original pseudocode and description, i.e., adding another state of a process, improved cache friendliness more precise complexity estimations and some other issues improving the robustness of the algorithm implementation....
-
Process arrival pattern aware algorithms for acceleration of scatter and gather operations
PublikacjaImbalanced process arrival patterns (PAPs) are ubiquitous in many parallel and distributed systems, especially in HPC ones. The collective operations, e.g. in MPI, are designed for equal process arrival times (PATs), and are not optimized for deviations in their appearance. We propose eight new PAP-aware algorithms for the scatter and gather operations. They are binomial or linear tree adaptations introducing additional process...
-
The Way One Defines Specification Matters: On the Performance Criteria for Efficient Antenna Optimization in Aggregated Bi-Objective Setups
PublikacjaDesign of antenna structures for real-world applications is a challenging task that often involves addressing multiple design requirements at a time. Popular solution approaches to this class of problems include utilization of composite objectives. Although configuration of such functions has a significant effect on the cost and performance of the optimization, their specific structure is normally determined based on engineering...
-
The Impact of a New Product’s Novelty and Meaningfulness on its Commercial Performance
Publikacjas new product development (NPD) process encompasses creative actions, so a new product is characterized by two essential dimensions used to describe any creative output – namely novelty and meaningfulness. Therefore, businesses are faced with the questions to what extent and under what market conditions to develop each of these dimensions in order to obtain high new product commercial performance. Based on gaps indentified in the...
-
Effects of n-butanol presence, inlet loading, empty bed residence time and starvation periods on the performance of a biotrickling filter removing cyclohexane vapors from air
PublikacjaThis paper presents the results of investigations on the removal of cyclohexane vapors from air using a peat-perlite packed biotrickling filter. Effects of basic process parameters i.e. IL (inlet loading) and EBRT (empty bed residence time) as well as introduction of n-butanol to the treated air stream and starvation periods on the process performance were evaluated. The results show that the introduction of hydrophilic n-butanol...
-
Improved Design Closure of Compact Microwave Circuits by Means of Performance Requirement Adaptation
PublikacjaNumerical optimization procedures have been widely used in the design of microwave components and systems. Most often, optimization algorithms are applied at the later stages of the design process to tune the geometry and/or material parameter values. To ensure sufficient accuracy, parameter adjustment is realized at the level of full-wave electromagnetic (EM) analysis, which creates perhaps the most important bottleneck due to...
-
Effects of liquid phase modification on the performance of biotrickling filters
Dane BadawczeDataset presents the effects of liquid phase modification on the biotrickling filtration (BTF) performance of air polluted with toluene, ethylbenzene, xylene and styrene.
-
Performance Models of a Multidomain IMS/NGN Service Stratum
PublikacjaThis paper quantifies call processing performance (CPP) of a multidomain IMS/NGN architecture, which was proposed to deliver current and future telecommunication services with strict quality requirements, independently of the transport network technologies. A realistic simulation model is used as a reference for evaluation of the analytical results, in which vari-ous types of queuing systems are applied to model the opera-tion...
-
Multi-Criteria Approach in Multifunctional Building Design Process
PublikacjaThe paper presents new approach in multifunctional building design process. Publication defines problems related to the design of complex multifunctional buildings. Currently, contemporary urban areas are characterized by very intensive use of space. Today, buildings are being built bigger and contain more diverse functions to meet the needs of a large number of users in one capacity. The trends show the need for recognition of...
-
Architecture Design of a Networked Music Performance Platform for a Chamber Choir
PublikacjaThis paper describes an architecture design process for Networked Music Performance (NMP) platform for medium-sized conducted music ensembles, based on remote rehearsals of Academic Choir of Gdańsk University of Technology. The issues of real-time remote communication, in-person music performance, and NMP are described. Three iterative steps defining and extending the architecture of the NMP platform with additional features to...
-
Topological modifications for performance improvement and size reduction of wideband antenna structures
PublikacjaCompact antennas belong to the key components of modern communication systems. Their miniaturization is often achieved by introducing appropriate topological changes such as simple ground plane slots or tapered feeds. More sophisticated modifications are rarely considered in the literature because they normally lead to significant increase of the number of tunable parameters, which makes the antenna design process more challenging....
-
Jerzy Kowalski dr hab. inż.
Osoby -
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublikacjaLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Studying the Effect of Working Conditions on WEDM Machining Performance of Super Alloy Inconel 617
PublikacjaWire electrical discharge machining (WEDM) has been for many years a precise and efficient non-conventional manufacturing solution in various industrial applications, mostly involving the use of hard-to machine materials like, among other, the Inconel super alloys. The focus of the present study is on exploring the effect of selected control parameters, including pulse duration, pulse-off time and the dielectric flow pressure on...
-
Pyrolysis Process of Whole Waste Tires as a Biomass Energy Recycling
PublikacjaThe article is devoted to the description of material recycling of whole waste tires, including a new method of pyrolysis process, resulting in the final products: technically oil fractions (rubber plasticizer of rubber compounds) or diesel fuels (light, medium and heavy), activated carbon, gas fuel and steel scrap. Operational and performance tests of the first version of the pilot plant, consisting of three contributions cooperating...
-
Tailoring a low-energy ball milled MnCo2O4 spinel catalyst to boost oxygen evolution reaction performance
PublikacjaThe development of cost-efficient oxygen evolution reaction (OER) catalysts is one of the most important tasks facing modern techniques for hydrogen production. In this work, for the first time, a low-energy ball milling process of MnCo2O4 (MCO) spinel powders, with a mechanical modification time exceeding 1 day was used. After 6 days of ball-milling, the obtained overpotential of the electrocatalyst reached the value of 375 mV...
-
Sequential treatment of landfill leachate by electrocoagulation/aeration, PMS/ZVI/UV and electro-Fenton: Performance, biodegradability and toxicity studies
PublikacjaThis study presents a systematic study on sequential treatment of highly resistant landfill leachate by electrocoagulation (EC)/aeration, sulfate radical advanced oxidation process (SR-AOP) and electro-Fenton (EF). In case of SR-AOP, peroxymonosulfate (PMS) catalyzed by zero valent iron (ZVI) and ultraviolet irradiation (UV) system was developed. Treatment process was optimized in respect to COD removal. Analysis of results revealed...
-
Performance of microbial fuel cells operated under anoxic conditions
PublikacjaNowadays, microbial fuel cells (MFC) stand up as a promising renewable energy source. Due to the ability of the MFC to oxidize a wide spectrum of substrates, wastewater seems to be one of the most interesting fuels. Unfortunately, wastewater could contain electron acceptors such as nitrate, which could interfere with the electrical performance of the MFC. In this work, the influence of oxidised nitrogen forms on the electricity...
-
Smart Virtual Product Development: Manufacturing Capability Analysis and Process Planning Module
PublikacjaSmart Virtual Product Development (SVPD) system provides effective use of information, knowledge, and experience in industry during the process of product development in Industry 4.0 scenario. This system comprises of three primary modules, each of which has been developed to cater to a need for digital knowledge capture for smart manufacturing in the areas of product design, production planning, and inspection planning. Manufacturing...
-
Towards a process based management system for oil port infrastructure in context of insurance
PublikacjaThis article addresses selected methodological aspects of a process based management system based on analysis of hazards and threats and risk evaluation for an oil port infrastructure in context of insurance. The oil port terminal is regarded as important system of the critical infrastructure that require careful system oriented approach to deal with integrated aspects of environmental, safety and security management to reduce...
-
A hybrid model of flooding of the ro-ro ships in damaged conditions
PublikacjaThe paper presents some results on investigations concerning development of a hybrid model for assessment of performance of the ro‐ro ships in damaged conditions. The model is devoted towards assessing the performance of the damaged ro‐ro ships at the preliminary stage of design. The key problems associated with preparing of such the model are associated with working out a method of assessment of the damaged roro ships performance,...
-
Additive Effect of Bromides and Chlorides on the Performance of Perovskite Solar Cells Fabricated via Sequential Deposition
PublikacjaA two-step sequential deposition method has been applied to prepare the solar cells with two types of perovskites Cs0.15FA0.85Pb(I0.95Cl0.05)3 and Cs0.15FA0.85Pb(I0.95Br0.05)3. In order to obtain the perovskite layers, the different sources of bromine and chlorine atoms were used for synthesis. The performance and time stability of chloride-based photocells are worse in comparison to the bromide-based devices. It can be explained...
-
NUMERICAL SIMULATIONS OF HONING PROCESS OF THIN WALL CYLINDER LINERS, WITH CONSTANT AND WITH VARIABLE THICKNESS OF WALL OF HONED PARTS
PublikacjaNumerical simulations of honing process of thin-wall cylinder liners, with constant and with variable thickness of the wall of honed workpieces can improve and can help to conduct the experimental research of honing process and can improve the honing process. A very valuable research assumption, before performing the numerical analysis of computer simulation of honing process, is the measurement of the real geometry of the honing...
-
VIBRATION SURVEILLANCE DURING MILLING OF FLEXIBLE DETAILS WITH A USE OF THE ACTIVE OPTIMAL CONTROL
PublikacjaThe main goal of modern machining operations is to achieve increasingly better performance. High Speed Machining and/or High Performance Cutting, despite a lot of advantages, have also some drawbacks, for example, a possibility of losing stability and development of self-excited chatter vibration. This paper presents an approach of vibration surveillance during high speed milling with a use of active optimal control. Non-stationary...
-
Ground Tire Rubber Filled Flexible Polyurethane Foam—Effect of Waste Rubber Treatment on Composite Performance
PublikacjaThe application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the...
-
Processing of Ce0.8Gd0.2O2-δ barrier layers for solid oxide cells: The effect of preparation method and thickness on the interdiffusion and electrochemical performance
PublikacjaCe0.8Gd0.2O1.9 (CGO) barrier layers are required to mitigate the chemical reactions between Sr-containing oxygen electrode materials and Zr-based oxygen ion conductors in high-temperature solid oxide cells. Barrier layers produced by different methods were studied in this work. As a reference, a cell with no barrier layer was measured. The application of the powder-processed barrier layers, considerably increases the performance....
-
Tacit Knowledge Sharing and Project Performance. Does the Knowledge Workers' Personal Branding Matter?
PublikacjaTacit knowledge sharing is the real challenge for knowledge management today. Network economy has completely changed the role of knowledge workers who now become independent tacit knowledge producers. Bearing this fact in mind, the author studied how tacit knowledge sharing affects the process of building a personal brand and project performance. For this purpose, the authors conducted a study among Polish professionals with different...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...