Wyszukiwarka
Filtry
wszystkich: 2433
wybranych: 1827
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: Dold coefficients
-
The unstable thermoelectric effect in non-stoichiometric Cu2Se during the non-equilibrium phase transition
PublikacjaThe superionic α ↔ β phase transition in Cu1.96Se thermoelectric material is investigated by means of thermal analysis (DSC) and measurements of Seebeck coefficient and electrical conductivity. Results of the DSC measurements with 1–10 K/min heating and cooling rates show that the material is close to the equilibrium phase composition during the transformation. However, the kinetic limitation of the process exists, which is indicated...
-
Weldability of high strength steels in wet welding conditions
PublikacjaIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Optical properties of the chemotherapy drugs used in the central nervous system lymphoma therapy: monitoring drug delivery
PublikacjaOur aim is to optically monitor the delivery of the chemotherapy drugs for brain tumours, particularly used in the central nervous system (CNS) lymphoma therapy. In vivo monitoring would help to optimize the treatment and avoiding unnecessary medications. Moreover, it would be beneficial to be able to measure which of the multi-regimen drugs actually do penetrate and how well into the brain tissue. There exist several potential...
-
Debonding of coin-shaped osseointegrated implants: Coupling of experimental and numerical approaches
PublikacjaWhile cementless implants are now widely used clinically, implant debonding still occur and is difficult to anticipate. Assessing the biomechanical strength of the bone–implant interface can help improving the understanding of osseointegration phenomena and thus preventing surgical failures. A dedicated and standardized implant model was considered. The samples were tested using a mode III cleavage device to assess the mechanical...
-
A Method for Optimising the Blade Profile in Kaplan Turbine
PublikacjaThis paper introduces a method of blade profile optimisation for Kaplan-type turbines, based on modelling the interaction between rotor and stator blades. Rotor and stator blade geometry is described mathematically by means of a midline curve and thickness distribution. Genetic algorithms are then used to find a global optimum that minimises the loss coefficient. This allows for variety of possible blade shapes and configurations....
-
An electrochemical biosensor for the determination of hormone Human Chorionic Gonadotropin (hCG) in human serum
PublikacjaThis work describes the modification of a gold electrode to create an electrochemical biosensor capable of detecting human chorionic gonadotropin (hCG). The biosensor was obtained by modifying the gold electrode with cysteamine and oligopeptide (PPLRINRHILTR). The modification steps of the gold electrode were confirmed by cyclic voltammetry (CV) and impedance electrochemical spectroscopy (EIS) measurements. The conducted EIS experiments...
-
Ocena odporności na pękanie podbudów drogowych z mieszanek mineralno-cementowo-emulsyjnych (MCE)
PublikacjaPodbudowy z mieszanek mineralno-cementowo-emulsyjnych (MCE) są jednym z wielu materiałów stosowanych do wykonywania warstw nawierzchni w ramach przebudów dróg w Polsce. Mieszanki MCE pozwalają na maksymalne powtórne wykorzystanie istniejących warstw konstrukcyjnych do budowy lub przebudowy nawierzchni. Do wykonania podbudów z MCE stosuje się materiał pochodzący z rozbiórki istniejących warstw (destrukt) bitumicznych, warstw związanych...
-
Reliable EM-driven size reduction of antenna structures by means of adaptive penalty factors
PublikacjaMiniaturization has become of paramount importance in the design of modern antenna systems. In particular, compact size is essential for emerging application areas such as internet of things, wearable and implantable devices, 5G technology, or medical imaging. On the other hand, reduction of physical dimensions generally has a detrimental effect on antenna performance. From the perspective of numerical optimization, miniaturization...
-
The demand for skills and the labor cost in partner countries: evidence from the enlarged EU
PublikacjaWe analyse the consequences of trade integration in Europe (1995-2005) detecting how thelabor costs in partner countries affects the demand for domestic high- and low-skilled labor inthe EU-15 (Old) and five New member states. In general, independently on the skill level, the resultshint at complementarity between domestic and foreign labor. However, the demand for thehigh skilled in New EU members' low skill intensive sectors...
-
A self-optimization mechanism for generalized adaptive notch smoother
PublikacjaTracking of nonstationary narrowband signals is often accomplished using algorithms called adaptive notch filters (ANFs). Generalized adaptive notch smoothers (GANSs) extend the concepts of adaptive notch filtering in two directions. Firstly, they are designed to estimate coefficients of nonstationary quasi-periodic systems, rather than signals. Secondly, they employ noncausal processing, which greatly improves their accuracy and...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publikacjamodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
BIODIVERSITY OF YEASTS ISOLATED FROM CAVES OF THE POLISH TATRA MOUNTAINS, AND ITS BIOTECHNOLOGICAL POTENTIAL
PublikacjaMost of the Earth’s biosphere is permanently or periodically exposed to temperatures below 5°C. Cold habitats harbor a wide diversity of psychrophiles. For many years Antarctica has been the geographic area preferred for studying the diversity and properties of cold-adapted microorganisms. However, the non-Antarctic habitats like Himalayas or Alps are also extensively explored. The Tatra Mountains are Europe’s second-highest massif...
-
Does migration lead to economic convergence in an enlarged European market?
PublikacjaThis paper examines the relationship between migration and convergence for the enlarged internal market of the European Union (EU27) for the period 1990-2007. The impact of migration on growth is estimated in two ways: by including the migration rate in a growth regression and examining its impact on the convergence coefficient; and from the actual coefficient on migration, which can be interpreted as the effect of migration on...
-
Mesh dependence study for numerical assessment of hydrodynamic characteristics of windsurfing fin
PublikacjaThe presented research aims to assess the drag coefficient and lift coefficient versus angle of attack curves for windsurfing fin. Special attention in the research was being paid to the evaluation of the stall angle value. The angle of incidence for which the stall occurs was searched, and the sensitivity of the solution for the mesh resolution was studied. The mesh resolution sensitivity analysis was done by systematically decreasing...
-
Comparison of oil yield and quality obtained by different extraction procedures from salmon (Salmo salar) processing byproducts
PublikacjaThe content and composition of lipids in different byproducts (skins, heads, and backbones) from mechanically processed farmed Atlantic salmon were determined and compared with that obtained from wild salmon. Three different procedures were used to establish the optimal conditions of oil extraction (at high temperature −95°C, “cold” extraction at temperature not exceeding 15°C and enzyme assisted with Alcalase). “Cold” extraction...
-
User experience evaluation study on the quality of 1K, 2K, and 4K H.265/HEVC video content
PublikacjaNowadays, most content creators focus on distributing rich media at the highest possible resolution. Currently, the majority of sold consoles, media players, computer hardware, as well as displays and TVs are advertised as 4K-compatible. The same trend is observed in the case of popular online streaming services and terrestrial TV broadcasts. Generally speaking, it is assumed that higher bitrates provide higher subjective judgements....
-
EFFECT OF NANOFLUID CONCENTRATION ON TWO-PHASE THERMOSYPHON HEAT EXCHANGER PERFORMANCE
PublikacjaAn approach – relaying on application of nanofluid as a working fluid, to improve performance of the two-phase thermosyphon heat exchanger (TPTHEx) has been proposed. The prototype heat exchanger consists of two horizontal cylindrical vessels connected by two risers and a downcomer. Tube bundles placed in the lower and upper cylinders work as an evaporator and a condenser, respectively. Distilled water and nanofluid water-Al2O3...
-
Economics of credit scoring management
PublikacjaCredit scoring models constitute an inevitable element of modern risk and profitability management in retail financial lending institutions. Quality,or separation power of a credit scoring model is usually assessed with the Gini coefficient. Generally, the higher Gini coefficient the better, as in this way a bank can increase number of good customers and/or reject more bad applicants. In...
-
Experimental study on the seepage flow through the ice jam
PublikacjaIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
Computer Supported Analysis of the Human Body Surface Area
PublikacjaRecent scientific studies show the growing importance of the coefficients: BSA and TBSA, as an alternative to the widely used BMI. The relevant indicators are widely used in medicine, including such areas as: the treatment of burns, chemotherapy, dermatology and toxicology; as benchmarks when calculating doses of drugs and fluids. The particular problems concerning this subject are: the change of the reference parameter value which...
-
Analysis of the Hydrodynamic Properties of the 3-Column Spar Platform for Offshore Wind Turbines
PublikacjaThe article presents a design of a floating platform for offshore wind turbines. The concept is a modification of the Spar design and consists of three variable section columns connected to each other by a ballast tank in the lower part of the platform. This solution makes it possible to influence the position of the centre of buoyancy and the centre of mass of the structure. Compared to the classic Spar platform structure, the...
-
Temper bead welding of S460N steel in wet welding conditions
PublikacjaWet welding is the most common method of welding in water environment. It is most often used for repairing of underwater parts of offshore structures. However, the water as a welding environment causes an increase of susceptibility of steels to cold cracking. For underwater constructions high strength low alloy (HSLA) steel are widely used. In wet welding condition a HSLA steel is characterized by high susceptibility to cold cracking....
-
Simplified saturation modelling in three-leg power transformer for the system stability analisys
PublikacjaThe paper presents a simplified method for modelling non-linearity of the magnetic circuit of the power transformer. The saturation effect is implemented by describing the self and mutual inductances as a function of the magnetic flux. The most important element of this function is the saturation coefficient which is calculated based on transient state during the unloaded transformer switch on. The transformer model is described...
-
Optimal Rotating Receiver Angles Estimation for Multicoil Dynamic Wireless Power Transfer
PublikacjaThis study proposed an approach to dynamic wireless charging that uses a rotating receiver coil. Our simulation study focused on the verification of a novel way of increasing the coupling coefficient and power transfer stability by following the flux of the transmitting coils. To obtain the highest possible coupling by means of the FEM analysis, we studied the optimization of the trajectory of the angular velocity of the rotating...
-
Fluorescence studies by quenching and protein unfolding on the interaction of bioactive compounds in water extracts of kiwi fruit cultivars with human serum albumin
PublikacjaThe main aim of this investigation was to characterize new kiwi fruit cultivars after cold storage treatment and to determine the similarities and differences between them, using spectroscopic methods. The chemometric comparison of kiwi fruit cultivars based on physicochemical indices during cold storage was carried out. All kiwi fruit cultivars showed a high level of correlation between the contents of phenolic compounds (polyphenols,...
-
Numerical study on pounding between two adjacent buildings under earthquake excitation
PublikacjaSeismic excitation, which results in large horizontal relative displacements, may cause collisions between two adjacent structures due to insufficient separation distance between them. Such collisions, known as earthquake-induced structural pounding, may induce severe damages. In this paper, the case of pounding between two adjacent buildings is studied by the application of single degree-of-freedom structural models. Impact is...
-
Applicability of arrays of microjets heat transfer correlations to design compact heat exchangers
PublikacjaThe article presents experimental studies on a compact heat exchanger with heat transfer intensification by means of impinging microjets. The pursuit to provide high performance of heat exchangers is a response to the demand both in economics and in the universal tendency to miniaturization of industrial equipment. This paper presents the design and tests of a prototype, microjet heat exchanger. The modular design of the heat exchanger...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublikacjaIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
On Memory-Based Precise Calibration of Cost-Efficient NO2 Sensor Using Artificial Intelligence and Global Response Correction
PublikacjaNitrogen dioxide (NO2) is a prevalent air pollutant, particularly abundant in densely populated urban regions. Given its harmful impact on health and the environment, precise real-time monitoring of NO2 concentration is crucial, particularly for devising and executing risk mitigation strategies. However, achieving precise measurements of NO2 is challenging due to the need for expensive and cumbersome equipment. This has spurred...
-
Statistical Data Pre-Processing and Time Series Incorporation for High-Efficacy Calibration of Low-Cost NO2 Sensor Using Machine Learning
PublikacjaAir pollution stands as a significant modern-day challenge impacting life quality, the environment, and the economy. It comprises various pollutants like gases, particulate matter, biological molecules, and more, stemming from sources such as vehicle emissions, industrial operations, agriculture, and natural events. Nitrogen dioxide (NO2), among these harmful gases, is notably prevalent in densely populated urban regions. Given...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublikacjaThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
The effect of calcination temperature on structure and photocatalytic properties of Au/Pd nanoparticles supported on TiO2
PublikacjaBimetallic nanoparticles, composed of two different metal elements, can exhibit peculiar electronic, optical, and catalytic or photocatalytic properties that are absent in the corresponding monometallic nanoparticles. We show the effect of calcination temperature (from 350 to 700°C) on the structure and the photocatalytic properties of Au/Pd-modified TiO2. The composition of the bimetallic Au/Pd nanoparticles in relation to their...
-
Sequences of fixed point indices of iterations in dimension 2.
PublikacjaW pracy dowodzi się, że każdy ciąg liczb całkowitych spełniający relacje Dolda może zostać zrealizowany jako ciąg indeksów punktu stałego iteracji ciągłego odwzorowania dwuwymiarowego dysku w siebie.
-
Problems of analysis of axially loaded steel behavior under laser welded panel
PublikacjaWprowadzanie do praktyki nowych rozwiązań konstrukcyjnych wymaga posiadania danych wejściowych do procesu modelowania ich zachowania. Takim nowym elementem jest stalowy, spawany laserowo panel typu sandwich. W pracy pokazano wy-brane problemy towarzyszące modelowaniu zachowań takiej struktury. Pokazano podstawy teoretyczne wyznaczania sztyw-ności panelu a następnie omówiono wyniki badań wyboczenio-wych serii modeli o zmiennej geometrii.
-
Thin-walled cross section shape influence on steel member resistance.
PublikacjaThis work describes why trending thin-walled technology is achieving popularity in steel construction sector. A purpose of this article is to present the influence of the cold-formed element cross-section shape on an axial compression and a bending moment resistance. The authors have considered four different shapes assuming constant section area and thickness. Calculations were based on three different steel grades taking into...
-
Preliminary experimental research on stability of truss' joint with positive eccentricity
PublikacjaRecently, a very large interest in lightweight steel structures made from cold-formed sections has been noticeable. In the design practice, a large emphasis is put on rational shaping of both the thin-walled elements and constructions designed on them. The aim of this paper is to present the methodology for preparation of experimental research that model the behaviour of members in trusses made of cold-formed sections with positive...
-
Subcritical bifurcation of free elastic shell of biological cluster
PublikacjaIn this paper we will investigate symmetry-breaking bifurcation of equilibrium forms of biological cluster. A biological cluster is a two-dimensional analogue of a gas balloon. The cluster boundary is connected with its kernel by elastic links. The inside part is filled with compressed gas or fluid. Equilibrium forms of biological cluster can be found as solutions of a certain second order ordinary functional-differential equation...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublikacjaHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Effects of Post-Harvest Elicitor Treatments with Ultrasound, UV- and Photosynthetic Active Radiation on Polyphenols, Glucosinolates and Antioxidant Activity in a Waste Fraction of White Cabbage (Brassica oleracea var. capitata)
PublikacjaBiosynthesis of phytochemicals in leaves of Brassica can be initiated by abiotic factors. The aim of the study was to investigate elicitor treatments to add value to waste of cabbage. A leaf waste fraction from industrial trimming of head cabbage was exposed to UV radiation (250–400 nm, 59 and 99 kJ m-2, respectively), photosynthetic active radiation (PAR, 400–700 nm, 497 kJ m-2), and ultrasound in water bath (35 kHz, at 15, 30...
-
Free trade with the former COMECON Countries as Unequal Exchange
PublikacjaTwo authors of this chapter were born to the East of what was once The Iron Curtain and two to the West. From both angles, the two systems – capitalism and communism – seemed to be as contrary to each other as possible. Few people are aware that in terms of industrial and trade policy, both classical capitalism and communism had a common root in the theories of German economist Friedrich List (1789-1846) (List, 1841). In fact,...
-
Rating Prediction with Contextual Conditional Preferences
PublikacjaExploiting contextual information is considered a good solution to improve the quality of recommendations, aiming at suggesting more relevant items for a specific context. On the other hand, recommender systems research still strive for solving the cold-start problem, namely where not enough information about users and their ratings is available. In this paper we propose a new rating prediction algorithm to face the cold-start...
-
Fortifications of Hel Peninsula in Poland – history, preservation and contemporary adaptation.
PublikacjaThe Hel Peninsula fortifications are one of the largest and most interesting historic coastal fortification complexes in Poland. Built from the 1930s until demilitarisation at the end of the Cold War, they are now one of the biggest tourist attractions of the region. The article attempts to describe the history of their development, current state and selected problems related to their protection and adaptation for touristic purposes....
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
A Bayesian regularization-backpropagation neural network model for peeling computations
PublikacjaA Bayesian regularization-backpropagation neural network (BRBPNN) model is employed to predict some aspects of the gecko spatula peeling, viz. the variation of the maximum normal and tangential pull-off forces and the resultant force angle at detachment with the peeling angle. K-fold cross validation is used to improve the effectiveness of the model. The input data is taken from finite element (FE) peeling results. The neural network...
-
The role of low-energy electrons in the charging process of LISA test masses
PublikacjaThe estimate of the total electron yield is fundamental for our understanding of the test-mass charging associated with cosmic rays in the Laser Interferometer Space Antenna (LISA) Pathfinder mission and in the forthcoming gravitational wave observatory LISA. To unveil the role of low energy electrons in this process owing to galactic and solar energetic particle events, in this work we study the interaction of keV and sub-keV...
-
Free convection of water-Al2O3 nanofluid from horizontal porous coated tube
PublikacjaThe main aim of the present study was to investigate the influence of nanoparticles on heat transfer coefficients during free convection of water-Al2O3 nanofluid from horizontal porous coated tube under atmospheric pressure for nanoparticle concentration of 0.01% by weight. Contrary to published data present study concerns on free convection of nanofluids in extensive, quiescent fluid.
-
Narrowband Transmission Quality in Presence of Modified IEEE 802.15.4a Impulse Radio Interference
PublikacjaThis paper presents results of measurement of narrowband transmission quality in presence of impulse radio UWB interference. IEEE 802.15.4a UWB signal is being used as interferer, also with frame structure modifications which lead to change spectrum of the interference. Equations and coefficients which allow to calculate ratio between power of useful and interference signal are also presented.
-
The Linear Array 2x1 of Slot Monopoles for 6-8.5 GHZ UWB Standard
PublikacjaThe results of numerical simulations and measurements of 2x1 linear array of slot monopoles are presented in the paper. At the begining a single slot monopole was designed. Next the 2x1 linear array of these monopoles was numerically tested for various configurations of the feeding network. The single monopole and the array were fabricated and the results of the measurements of the reflection coefficients and the radiationpatterns...
-
Spinal Cord Injury: A Review Of Current Management Considerations And Emerging Treatments
Publikacja -
The EU enlargement and domestic employment
PublikacjaThe study focuses on the interactions between EU member states' labor markets (manufacturing and tradable business services) over the period 1995-2005. We use recently released detailed sector level employment statistics, considering the effects of trade integration on the creation of links between labor force in ''Old'' and ''New'' partners in the enlarged EU. Empirical estimations show that the domestic demand for labor in the...