Filtry
wszystkich: 1416
wybranych: 1040
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: · BEHAVIOURAL LOYALTY
-
Magnetoelectric effect in (BiFeO3)x–(BaTiO3)1-x solid solutions
PublikacjaThe aim of the present work was to study magnetoelectric effect (ME) in (BiFeO3)x–(BaTiO3)1x solid solutions in terms of technological conditions applied in the samples fabrication process. The rapidly growing interest in these materials is caused by their multiferroic behaviour, i.e. coexistence of both electric and magnetic ordering. It creates possibility for many innovative applications, e.g. in steering the magnetic memory...
-
Impact damage in SiO2 nanoparticle enhanced epoxy – Carbon fibre composites
PublikacjaLow velocity impact behaviour of nano-SiO2 enhanced carbon fibre/epoxy composites for naval applications is reported. Epoxy resin matrix was enhanced by 1- 8 wt% SiO2 nanoparticles, based on industrial surface-modified nanosilica. Impact parameters: force, deformation, energy, damage size were recorded. The most pronounced effect was damage size decrease; e.g. ∼28% recorded by infrared thermography and X-ray computed radiography...
-
Experimental and Numerical Study on Pounding of Structures in Series
PublikacjaPounding between structures in series during earthquakes may cause serious damage in the structural elements. The aim of this paper is to show the results of an experimental and numerical study that is focused on pounding between more than two structures which may be described as “structures in series”. In this study, the shaking table experiments, as well as the numerical analyses, were performed using three tower models including...
-
Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu „Geb“
PublikacjaOne of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight, so manufacturers are increasingly using the possibilities of those sections for the production of typical single-storey steel structures systems. Well known profiles, such as Z, C and the so called hat sections that have been studied and described in the literature, are used mainly as purlins or truss components....
-
Textile reinforced concrete members subjected to tension, bending, and in-plane loads: Experimental study and numerical analyses
PublikacjaTextile reinforced concrete has raised increasing research interest during the last years, mainly due to its potential to be used for freeform shell structures involving complex load situations. Yet, most experimental work has focused on test setups with primarily uniaxial loading. In the current work, such setups are complemented with a novel test setup of deep beams, including in-plane bending and shear. Further, nonlinear finite...
-
Application of a stochastic compartmental model to approach the spread of environmental events with climatic bias
PublikacjaWildfires have significant impacts on both environment and economy, so understanding their behaviour is crucial for the planning and allocation of firefighting resources. Since forest fire management is of great concern, there has been an increasing demand for computationally efficient and accurate prediction models. In order to address this challenge, this work proposes applying a parameterised stochastic model to study the propagation...
-
FRP-based reinforcement coatings of steel with application prospects in ships and offshore structures: a review
PublikacjaLatest research on novel FRP-based anti-corrosion structural coatings (for enhancing structural capacity and strengthening the coating layer) is discussed with application prospects for ships and offshore structures. In the marine environment, structures constantly face corrosion and fatigue cracks. Combining this with high operational and wave loads, it might cause a structural collapse. Recently, polymer composites have been...
-
TIME-DOMAIN NUMERICAL EVALUATION OF SHIP RESISTANCE AND MOTION IN REGULAR WAVES BY USING THE CFD URANS METHOD
PublikacjaTaking into account the International Maritime Organisation’s (IMO) strategy to radically reduce the GHG emitted by the shipping industry towards zero emission operation, today's assessment of ship behaviour in waves, its seakeeping characteristics and resistance and their interrelation with fuel consumption and emissions are one of the most attended research subject. There are three methods to conduct this analysis, which are...
-
Thermal analysis of Magnetohydrodynamics (MHD) Casson fluid with suspended Iron (II, III) oxide-aluminum oxide-titanium dioxide ternary-hybrid nanostructures
PublikacjaThis study is carried out to enhance and analyze the thermal performance of non-Newtonian Casson fluid by immersing Ternary hybrid nanoparticles Fe3O4-Al2O3-TiO2 uniformly. To model the behaviour of such complex phenomena mathematically, a system of complex transport differential equations is developed by utilizing a non-Fourier heat transfer model for energy transport. The non-dimensional system of transport equations involving...
-
Monitoring and analytics of semivolatile organic compounds (SVOCs) in indoor air
PublikacjaThis paper reviews literature information on the behaviour of semivolatile organic compounds (SVOCs) in the indoor environment, as well as the most likely emission sources. The consecutive stages of analytical procedures used for monitoring SVOCs in indoor environments are described. The most common approaches used for collecting samples from the gas and particulate phases are mentioned. The paper discusses and compares various...
-
Leakage detection and localisation in drinking water distributionnetworks by MultiRegional PCA
PublikacjaMonitoring is one of the most important steps in advanced control of complex dynamic systems. Precise information about systems behaviour, including faults indicating, enables for efficient control. The paper describes an approach to detection and localisation of pipe leakage in Drinking Water Distribution Systems (DWDS) representing complex and distributed dynamic system of large scale. Proposed MultiRegional Principal Component...
-
Numerical Analysis of a Steel Frame Building with Soft-storey Failure under Ground Motion Excitation
PublikacjaThe aim of this paper is to show the results of a numerical analysis focused on the behaviour of multi-storey steel frame building that suffers from a soft-storey failure under ground motion excitation. A numerical model of the structure was created in FEM computer software and was exposed to an impact that would have been generated after a soft-storey failure due to falling of the upper floors. During the analysis, the whole structure...
-
Effect of adhesive compliance in the assessment of soft adhesives with the wedge test
PublikacjaWedge tests are usually analysed assuming that the free, unbonded members may be treated as encastré cantilever beams. However, if the adhesive layer is sufficiently flexible (e.g., due to low elastic modulus), then significant strain in the bonded region may occur and lead to modification of the behaviour outside this region. Using in conjunction a sensitive strain gauge method on asymmetric wedge tests and a mathematical analysis...
-
The literature review on boundary conditions of use for non-residential buildings
PublikacjaThis paper describes the results of qualitative and quantitative literature reviews on boundary conditions within educational buildings, emphasising the users' perspective. The reviews were performed before and during the COVID-19 pandemic using Scopus, Taylor& Francis, Web of Science databases. The boundary conditions understood as special characteristics for use and or precondition, determining specific features of buildings...
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublikacjaThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
The literature review on boundary conditions of use for non-residential buildings. Educational buildings.
PublikacjaThis paper describes the results of qualitative and quantitative literature reviews on boundary conditions within educational buildings, emphasising the users' perspective. The studies were performed before and during the COVID-19 pandemic using Scopus, Taylor& Francis, and Web of Science databases. The boundary conditions are understood as special characteristics for use and or precondition, determining specific features of...
-
Structural and electrochemical heterogeneities of boron-doped diamond surfaces
PublikacjaThis brief review is focussed on the recent progress in studies of the heterogeneous electrochemical behaviour of various boron-doped materials extending from zero-dimensional particles through polycrystalline or nanostructured three-dimensional surfaces. A boron-doped diamond reveals large heterogeneities induced by numerous factors, inter alia multi-faceted crystallinity, inhomogeneous boron concentration, sp2/sp3-carbon ratio,...
-
Shear resistance of low height precast concrete lintels
PublikacjaThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Justification of quasi-stationary approximation in models of gene expression of a self-regulating protein
PublikacjaWe analyse a model of Hes1 gene transcription and protein synthesis with a negative feedback loop. The effect of multiple binding sites in the Hes1 promoter as well as the dimer formation process are taken into account. We consider three, possibly different, time scales connected with: (i) the process of binding to/dissolving from a binding site, (ii) formation and dissociation of dimers, (iii) production and degradation of Hes1...
-
Thermodynamic study of binary mixtures of toluene with ionic liquids, 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, 1-hexyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide and 1-butylpyridinium bis(trifluoromethylsulfonyl)imide
PublikacjaDensities, refractive indices and viscosities at 293.15, 298.15, 303.15, 308.15 and 313.15 K of binary mixtures of toluene with 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, 1-hexyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide and 1-butylpyridinium bis(trifluoromethylsulfonyl)imide have been measured over the miscible region at p = 0.1 MPa. From the experimental data, values of excess molar volume,...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublikacjaThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Vibration-Based Investigation of a Historic Bell Tower to Understand the Occurrence of Damage
PublikacjaABSTRACT The paper presents a survey of the historic Arch-cathedral bell tower in Vilnius induced by the appearance of cracks in the structure after a new bell system installation. An attempt is undertaken to identify the reason for the crack occurrence and to check a possible crack influence on global structural behaviour. The research is based on dynamic measurements made in the tower during ambient vibrations and during vibrations...
-
Electrical Stimulation Modulates High Gamma Activity and Human Memory Performance
PublikacjaDirect electrical stimulation of the brain has emerged as a powerful treatment for multiple neurological diseases, and as a potential technique to enhance human cognition. Despite its application in a range of brain disorders, it remains unclear how stimulation of discrete brain areas affects memory performance and the underlying electrophysiological activities. Here, we investigated the effect of direct electrical stimulation...
-
Behavior Based Complete Coverage Task of Unknown Area by an Autonomous Mobile Robot SCORPION with Static Obstacles in Environment
PublikacjaIn the paper the behavior based control system of an autonomous mobile robot SCORPION is presented to execute the one of the most difficult navigation task, which is the complete coverage task of unknown area with static obstacles in the environment. The main principle assumed to design control system was that the robot should cover all area only once, if it possible, to optimize the length of path and energy consumption. All commercial...
-
Efficient Simulation-Based Global Antenna Optimization Using Characteristic Point Method and Nature-Inspired Metaheuristics
PublikacjaAntenna structures are designed nowadays to fulfil rigorous demands, including multi-band operation, where the center frequencies need to be precisely allocated at the assumed targets while improving other features, such as impedance matching. Achieving this requires simultaneous optimization of antenna geometry parameters. When considering multimodal problems or if a reasonable initial design is not at hand, one needs to rely...
-
Data-Driven Surrogate-Assisted Optimization of Metamaterial-Based Filtenna Using Deep Learning
PublikacjaIn this work, a computationally efficient method based on data driven surrogate models is pro-posed for the design optimization procedure of a Frequency Selective Surface (FSS)-based filtering antenna (Filtenna). A Filtenna acts as a as module that simultaneously pre-filters unwanted sig-nals, and enhances the desired signals at the operating frequency. However, due to a typically large number of design variables of FSS unit elements,...
-
Multimodal human-computer interfaces based on advanced video and audio analysis
PublikacjaMultimodal interfaces development history is reviewed briefly in the introduction. Some applications of multimodal interfaces to education software for disabled people are presented. One of them, the LipMouse is a novel, vision-based human-computer interface that tracks user’s lip movements and detect lips gestures. A new approach to diagnosing Parkinson’s disease is also shown. The progression of the disease can be measured employing...
-
Multimodal human-computer interfaces based on advanced video and audio analysis
PublikacjaMultimodal interfaces development history is reviewed briefly in the introduction. Examples of applications of multimodal interfaces to education software and for the disabled people are presented, including interactive electronic whiteboard based on video image analysis, application for controlling computers with mouth gestures and the audio interface for speech stretching for hearing impaired and stuttering people. The Smart...
-
Numerical analysis of mechanical properties of an infill structure used in 3D printings
PublikacjaThe paper presents results of a numerical analysis focused on an identification of mechanical properties of an element created by using Fused Deposition Modelling additive manufacturing technique (FDM). There is presented a description of technology of the 3D printing, numerical model created by using the finite element method (FEM), as well as some problems referred to estimation of the mechanical properties of the printout. The...
-
Failure mode prediction for composite structural insulated panels with MgO board facings
PublikacjaSandwich panels are readily used in civil engineering due to their high strength to weight ratio and the ease and speed of assembly. The idea of a sandwich section is to combine thin and durable facings with a light-weight core and the choice of materials used allows obtaining the desired behaviour. Panels in consideration consist of MgO (magnesium oxide) board facings and expanded polystyrene core and are characterized by immunity...
-
Feasibility Study for Food Intake Tasks Recognition Based on Smart Glasses
PublikacjaIn this exploratory study 13 adult test subjects have performed different food intake tasks while wearing a three axis accelerometer mounted at a temple of glasses. Two different algorithms for task recognition have been applied and compared. The retrospective data processing leads to better task recognition results when the frequency range of 50 Hz to 100 Hz is analysed within accelerometer signal recordings. A straightforward...
-
Influence of silver nanoparticles addition on antibacterial properties of PEO coatings formed on magnesium
PublikacjaMagnesium is a biodegradable material and thus could be a choice for bone fixation devices and implants with a specific purpose. This study aims to enhance the anti-corrosive, biocompatible, and antibacterial properties on magnesium-based materials through ceramic coatings formation. To achieve this the silicate-based electrolyte was used to create of Plasma Electrolytic Oxidation (PEO) coatings. During investigation the bioactive...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublikacjaEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
Linear viscoelastic modelling of damage-involved structural pounding during earthquakes
PublikacjaDamage-involved structural pounding during earthquakes has been recently intensively studied using different impact force models. The results of the previous studies indicate that the linear viscoelastic model is relatively simple yet accurate in modelling pounding-involved behaviour of structures during earthquakes. The only shortcoming of the model is a negative value of the pounding force occurring just before separation, which...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublikacjaAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublikacjaAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
Sensing the onset of epoxy coating degradation with combined Raman spectroscopy/atomic force microscopy/electrochemical impedance spectroscopy
PublikacjaThe paper presents the results of investigation on epoxy resin durability upon 12-week exposure to UV radiation. The aim was early determination of the onset of epoxy degradation and for this purpose an epoxy film on steel substrate systems were periodically inspected using Raman spectroscopy, atomic force microscopy and electrochemical impedance spectroscopy. The behaviour of examined polymer could be divided into three periods: immunity,...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublikacjaWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Proton-Electron Hole Interactions in Sr(Ti,Fe)O3−δ Mixed-Conducting Perovskites
PublikacjaOxides in which total electrical conductivity is determined by the partial conductivities of three types of charge carriers i.e. holes/ electrons, oxygen ions, and protons are key components of well-functioning proton ceramic fuel cells. Apart from electrochemical properties also easily modified microstructure is an important feature of the electrodes. In the paper, a group of SrTi1−xFexO3−δ (STF, x = 0.2–0.8) perovskites prepared...
-
Design of a compact planar transmission line for miniaturized rat-race coupler with harmonics suppression
PublikacjaThis paper presents an elegant yet straightforward design procedure for a compact rat-race coupler (RRC) with an extended harmonic suppression. The coupler’s conventional λ/4 transmission lines (TLs) are replaced by a specialized TL that offers significant size reduction and harmonic elimination capabilities in the proposed approach. The design procedure is verified through the theoretical, circuit, and electromagnetic (EM) analyses,...
-
Numerical modelling and analysis of steel specimens subjected to marine immersed corrosion and tensile load
PublikacjaThe present study develops numerical models to analyse the behaviour of steel specimens subjected to marine immersed corrosion degradation and tensile load. The finite element method with the use of the explicit dynamic solver LS-DYNA, satisfying the quasi-static conditions, is employed. Two numerical models are developed, where in the first one, the scans of surfaces gathered from corroded plate specimens are implemented directly...
-
Formal Institutions: the Source of Unproductive Entrepreneurship in Poland
PublikacjaThe purpose of this article is to determine the entrepreneurs' perception of formal institutions in Poland as a source of non-productive behaviours. The research methodology was developed based on many years of the teams' research experience. It involved three stages of research: 1) panel of experts and 2) telephone surveys of 1,612 entrepreneurs in Poland, which were the basis for 3) development of detailed research to be conducted...
-
Gamma oscillations precede interictal epileptiform spikes in the seizure onset zone
PublikacjaOBJECTIVE: To investigate the generation, spectral characteristics, and potential clinical significance of brain activity preceding interictal epileptiform spike discharges (IEDs) recorded with intracranial EEG. METHODS: Seventeen adult patients with drug-resistant temporal lobe epilepsy were implanted with intracranial electrodes as part of their evaluation for epilepsy surgery. IEDs detected on clinical macro- and research microelectrodes...
-
Studencki konkurs budowy mostów wyKOMBinuj mOst 2011
PublikacjaKonkurs budowy mostów wyKOMBinuj mOst na trwałe wpisał się już w kalendarz najważniejszych imprez studenckich kierunków związanych z budownictwem. Konkurs ten jest organizowany od 2008 roku przez Koło Naukowe Mechaniki Budowli KOMBO, działające przy Katedrze Mechaniki Budowli i Mostów (Wydział Inżynierii Lądowej i Środowiska, Politechnika Gdańska). Pierwsza edycja konkursu, w której uczestniczyło 12 drużyn, miała charakter lokalny....
-
Types of Markov Fields and Tilings
PublikacjaThe method of types is one of the most popular techniques in information theory and combinatorics. However, thus far the method has been mostly applied to one-dimensional Markov processes, and it has not been thoroughly studied for general Markov fields. Markov fields over a finite alphabet of size m ≥ 2 can be viewed as models for multi-dimensional systems with local interactions. The locality of these interactions is represented...
-
Scoreboard Architectural Pattern and Integration of Emotion Recognition Results
PublikacjaThis paper proposes a new design pattern, named Scoreboard , dedicated for applications solving complex, multi-stage, non-deterministic problems. The pattern provides a computational framework for the design and implementation of systems that integrate a large number of diverse specialized modules that may vary in accuracy, solution level, and modality. The Scoreboard is an extension of Blackboard design pattern and comes under...
-
Overcoming Phobias: Harnessing the Power of Immersive Virtual Reality Therapy
PublikacjaThe goal of the chapter was to review the different therapeutic techniques used in the treatment of various forms of phobias, with particular emphasis on virtual reality treatment. We define different types of phobias, including social ones. We also describe treatment techniques – adopted from behavioral therapy – which have been developed to aid the treatment of phobias. Particular emphasis has been placed on the flooding, implosive...
-
Biocompatibility and bioactivity of load-bearing metallic implants
PublikacjaThe main objective of here presented research is to develop the titanium (Ti) alloy base composite materials possessing better biocompatibility, longer lifetime and bioactivity behaviour for load-bearing implants, e.g. hip joint and knee joint endoprosthesis. The development of such materials is performed through: modeling the material behaviour in biological environment in long time and developing of new procedures for such evaluation;...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublikacjaThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
In-situ odd random phase electrochemical impedance spectroscopy study on the electropolymerization of pyrrole on iron in the presence of sodium salicylate – The influence of the monomer concentration
PublikacjaIn this work, the potentiostatic electropolymerization of polypyrrole (PPy) on iron in aqueous solution of sodium salicylate and pyrrole is studied in situ by odd random phase electrochemical impedance spectroscopy (ORP-EIS). The influence of the pyrrole concentration on the electrosynthesis process is investigated. The ORP-EIS technique ensures a reliable analysis of the PPy electrosynthesis on iron by means of an advanced data...