Wyszukiwarka
Filtry
wszystkich: 3271
wybranych: 1834
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SPINDLE
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublikacjaMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Improving Control Dynamics of PMSM Drive by Estimating Zero-Delay Current Value
PublikacjaDynamic performance of current control loop still remains crucial for position-, speed-, and torque-controlled drives. In the study, a current loop solution has been designed for field oriented control of permanent magnet synchronous motors (PMSM). It enhances typical PI controller with an estimator of zero-delay current (ZDC) value. The ZDC estimation allows for selecting substantially higher controller gain. It reduces control...
-
Quantum mechanical which-way experiment with an internal degree of freedom
PublikacjaFor a particle travelling through an interferometer, the trade-off between the available which-way information and the interference visibility provides a lucid manifestation of the quantum mechanical wave-particle duality. Here we analyse this relation for a particle possessing an internal degree of freedom such as spin. We quantify the trade-off with a general inequality that paints an unexpectedly intricate picture of wave-particle...
-
Conjectured strong complementary-correlations tradeoff
PublikacjaWe conjecture uncertainty relations that restrict correlations between the results of measurements performed by two separate parties on a shared quantum state. The first uncertainty relation bounds the sum of two mutual informations when one party measures a single observable and the other party measures one of two observables. The uncertainty relation does not follow from the Maassen-Uffink uncertainty relation and is much stronger...
-
Hierarchical Estimation of Human Upper Body Based on 2D Observation Utilizing Evolutionary Programming and 'Genetic Memory'
PublikacjaNew method of the human body pose estimation based on single camera 2D observation is presented. It employs 3D model of the human body, and genetic algorithm combined with annealed particle filter for searching the global optimum of model state, best matching the object's 2D observation. Additionally, motion cost metric is employed, considering current pose and history of the body movement, favouring the estimates with the lowest...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublikacjaSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Low frequency of itraconazole resistance found among avian Aspergillus fumigatus isolates
PublikacjaAspergillus fumigatus is the most frequent etiological factor of invasive aspergillosis in human as well as animals, including birds. Aspergillosis caused by drug-resistant strains poses a significant therapeutic issue, especially if resistance pattern includes insensitivity to triazoles, i.e. drugs recommended for the primary therapy purposes. Majority of resistant isolates hold the TR34/L98H...
-
Load Tests of the Movable Footbridge Over the Port Canal in Ustka
PublikacjaThe paper presents the acceptance tests carried out on the open footbridge over the port canal in the Port of Ustka. The steel footbridge construction is created by a single pylon to which a movable truss span is suspended with a theoretical span of 52.3 m. The studies about load test of the object included static and dynamic extortion and measurements. In static tests the ballast was of pallets with concrete blocks. Dynamic studies...
-
Structure of EstA esterase from psychrotrophic Pseudoalteromonas sp. 643A covalently inhibited by monoethylphosphonate.
PublikacjaThe crystal structure of the esterase EstA from the cold-adapted bacteriumPseudoalteromonas sp. 643A was determined in a covalently inhibited form at aresolution of 1.35 A˚. The enzyme has a typical SGNH hydrolase structureconsisting of a single domain containing a five-stranded beta-sheet, with threehelices at the convex side and two helices at the concave side of the sheet, and isornamented with a couple of very short helices...
-
Hybrid battery based on arylated carbon nanotubes and laccase
PublikacjaSingle-walled carbon nanotubes (SWCNT) were covalently modified with anthracene and anthraquinone and used for the construction of cathodes for biocatalytic reduction of dioxygen. The nanotubes with aromatic groups casted onto the electrode increased the working surface of the electrode and enabled efficient direct electron transfer (DET) between the enzyme and the electrode. The aryl groups enter the hydrophobic pocket of the...
-
Merging Images From Parallel Depth Cameras
PublikacjaIn this paper a problem of simultaneous information acquisition from multiple depth cameras is investigated, aiming at obtaining single overall picture containing information from all cameras. The experiments are carried out on Microsoft Kinect devices. A methodology for merging images from multiple positioned in a line cameras is proposed. The method is based on the concept of simulating a view of an imaginary camera covering...
-
Improving agility and discipline of software development with the Scrum and CMMI
PublikacjaThis study presents a method of combining the Scrum methodology with the CMMI maturity model to improve bothagility and discipline of software development. First, the authors propose the CMMI-Scrum reference model, which maps Scrumpractices onto 123 practices of CMMI staged levels 2 and 3. For 60% of CMMI practices, which are insufficiently covered byScrum they add new practices that improve discipline while maintaining agility....
-
Electric field-assisted dissociation of singlet excitons in tris-(8-hydro-xyquinolinato)aluminium (III)
PublikacjaW pracy podano szczegółowemu badaniu kompleks organo-metaliczny 8-hydroksy-chinoliny i aluminium (ALq3) metodą pomiaru fotopądów i elektromodulacji luminescencji. Stwierdzono, że w obszarze wysokich pól elektrycznych (F>105 V/cm) ładunek wytwarzany jest w procesie dysocjacji wzbudzonych stanów single-towych. Wyjaśnienie przebiegów prądowych w zakresie niskich pól elektrycznych (F<105 V/cm) wymagało włączenia zjawiska rekombinacji...
-
Exploring the Reactivity of Unsymmetrical Diphosphanes toward Heterocumulenes: Access to Phosphanyl and Phosphoryl Derivatives of Amides, Imines, and Iminoamides
PublikacjaWe present a comprehensive study on the diphosphanation of iso(thio)cyanates by unsymmetrical diphosphanes. The reactions involving unsymmetrical diphosphanes and phenyl isocyanate or phenyl thioisocyanate gave rise to phosphanyl, phosphoryl, and thiophosphoryl derivatives of amides, imines, and iminoamides. The structures of the diphosphanation products were confirmed through NMR spectroscopy, IR spectroscopy, and single-crystal...
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublikacjaThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
Displacement Sensors Based on the Phase of the Reflection Coefficient of a Split Ring Resonator Loaded Transmission Line
Publikacja— In this paper, novel displacement sensors using a microstrip loaded with a pair of split ring resonators (SRRs) are proposed. It is shown that the phase of the reflection coefficient from the loading SRRs can be used for displacement sensing. The paper also proposes a differential version of the sensor that benefits from a higher sensitivity and reference zero, which is useful for alignment purposes. It is further shown that...
-
Double ZIF-L structures with exceptional CO2 capacity
PublikacjaCarbon dioxide emission is an emerging problem nowadays and new methods are designed for its control. In this article, a report on the formation of zeolitic imidazole framework with an apparent double leaf-like morphology DZIF-L is given. The special structure of the materials prevents from aggregation of the particles providing remarkable CO2 capacity. At 0.1 MPa the CO2 uptake was 2.99 ± 0.06 mmol/g. The capacity of synthesized...
-
Corrigendum to “An investigation on residual stress and fatigue life assessment of T-shape welded joints” [Eng. Fail. Anal. 141 (2022) 106685]
PublikacjaThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
On the Buckling Response of Axially Pressurized Nanotubes Based on a Novel Nonlocal Beam Theory
PublikacjaIn the present study, the buckling analysis of single-walled carbon nanotubes (SWCNT) on the basis of a new refined beam theory is analyzed. The SWCNT is modeled as an elastic beam subjected to unidirectional compressive loads. To achieve this aim, the new proposed beam theory has only one unknown variable which leads to one equation similar to Euler beam theory and is also free from any shear correction factors. The equilibrium...
-
Detailed studies of superconducting properties of Y2Pd1.25Ge2.75
PublikacjaWe report a successful synthesis of a high-purity intermetallic germanide Y2Pd1.25Ge2.75, crystallizing in the disordered variant of the AlB2-type structure. A single-phase sample was obtained via arc-melting by deliberately tuning the composition out of the ideal 2:1:3 ratio. Specific heat, electrical resistivity and magnetization measurements show that the compound is a weakly-coupled (λ e-p = 0.58) type-II superconductor with...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
The role of trade in intra industry productivity growth - the case of old and new European Union countries.
PublikacjaThe purpose of this paper is to evaluate the role of trade in productivity growth in a sample of 30 sectors in 25 EU countries in the period of rapid East–West integration (1995–2007). Shift-share analysis is used to show that changes in value added per hour worked in these countries appear to be mainly due to positive developments (rising productivity) within single industries and only to a lower extent result from a shift towards...
-
π-Indenyl substituted zirconium compounds containing terminal bondedphosphanylphosphido ligands [Ind2Zr(Cl){(Me3Si)P-PR2-jP1}]. Synthesis,X-ray analysis and NMR studies
PublikacjaPraca prezentuję reakcję kompleksów indenylowych cyrkonu z solami litowymi difosfanów o ogólnym wzorze R2P-P(SiMe3)Li, gdzie R = tBu, Et2N, iPr2N. W wyniku tych reakcji otrzymano 3 nowe kompleksy fosfanylofosfidowe.Otrzymane nowe kompleksy zbadano przy pomocy technik rentgenowskiej analizy strukturalnej i NMR.Dichloro-bis(indenyl)zirconium(IV) reacts with lithium derivatives of diphosphanes R2P-P(SiMe3)Li (R = tBu, Et2N, iPr2N)...
-
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
An optimised placement of the hard quality sensors for a robust monitoring of the chlorine concentration in drinking water distribution systems
PublikacjaThe problem of an optimised placement of the hard quality sensors in drinking water distribution systemsunder several water demand scenarios for a robust monitoring of the chlorine concentration is formulatedin this paper. The optimality is understood as achieving a desired trade off between the sensors and theirmaintenance costs and the accuracy of estimation of the chlorine concentration. The contribution of thiswork is a comprehensive...
-
Alternative cogeneration thermodynamic cycles for domestic ORC
PublikacjaThe Organic Flash Cycle (OFC) is suggested as a vapor power cycle that could potentially improve the efficiency of utilization of the heat source. Low and medium temperature finite thermal sources are considered in the cycle. Additionally the OFC’s aim is to reduce temperature difference during heat addition. The study examines 2 different fluids. Comparisons are drawn between the OFC and an optimized basic Organic Rankine Cycle...
-
Timber-frame house resistant to dynamic loads - analysis of wall panel filled with polyurethane foam
PublikacjaThe present study shows the experimentally and numerically determined response of a single timber-frame house wall panel filled with polyurethane (PU) foam under dynamic loads. The harmonic tests were conducted for the following frequencies: 0.5 Hz, 1.0 Hz, 2.0 Hz and 5.0 Hz for various values of the specified displacement. Based on the results of the comparison between the experimental tests and the numerical analyses, the numerical...
-
Earth wires currents calculation by tableau analysis
PublikacjaThe paper presents a new method to compute a phase-to-earth fault current distribution in overhead transmission line. The method is based on the tableau analysis of an unbalanced, multi-wire model of a transmission line. It allows for the calculation of current distribution in overhead earth wires along the transmission line. Additionally, it may be used to calculate currents in a tower’s earthing system as well as voltages over...
-
Design and optimization of a novel compact broadband linearly/circularly polarized wide-slot antenna for WLAN and Wi-MAX applications
PublikacjaA novel topologically modified structure of a compact low profile wide-slot antenna for broadband applications is presented. The antenna comprises a modified E-shaped slot with unequal arm lengths in the ground plane, and a parasitic quasi-rectangular loop placed coplanar with the feedline. For exciting orthogonal modes with equal amplitude, a single-point feeding technique with an asymmetrical geometry of the coplanar waveguide...
-
Real-Time Volatilomics: A Novel Approach for Analyzing Biological Samples
PublikacjaThe use of the ‘omics techniques in environmental research has become common-place. The most widely implemented of these include metabolomics, proteomics, genomics, and transcriptomics. In recent years, a similar approach has also been taken with the analysis of volatiles from biological samples, giving rise to the so-called ‘volatilomics’ in plant analysis. Developments in direct infusion mass spectrometry (DI-MS) techniques have...
-
Numerical modeling and experimental validation of full-scale segment to support design of novel GFRP footbridge
PublikacjaThe paper contains analysis of full-scaled three meters long segment of a novel composite footbridge. Both numerical modeling and experimental validation were performed. Analyzed object is a shell type sandwich channel-like structure made of composite sandwich with GFRP laminates as a skin and PET foam as a core. Several static load schemes were performed including vertical and horizontal forces. In FEM analysis multilayered laminate...
-
Collision-induced luminescence spectra of pyridine bombarded by 1000 eV He+ cations
PublikacjaHere we show collision-induced luminescence spectra measured for collisions of the He+cations with thearomatic six-membered ring of the pyridine molecule (C5H5N). Distinct emission bands due to the CH(A2Δ→X2Πr;B2Σ+→X2Πr;C2Σ+→X2Πr), CN(B2Σ+→X2Σ+), C2(d3Πg→a3Πu), and NH(A3Π→X3Σ−) transitions, aswell as atomic H, He, and C lines have been observed. Apart from the He atoms, all the emitters arise from thefragmentation of the pyridine...
-
Razem czy osobno - zespoły a działania przedsiębiorcze
PublikacjaPrzedsiębiorczość rozumiana jako atrybut jednostki, charakteryzowana jest ponad 40 pojęciami. Wiadomo jest jednak, że zakres i różnorodność kompetencji pojedynczej osoby jest zazwyczaj mniejszy niż zespołu. Jednostka może posiadać wybitną wiedzę, niezwykły poziom umiejętności i ogromne doświadczenie, ale ich zakres może zostać rozszerzony o właściwie dobrane kompetencje innej jednostki. Z drugiej strony zarówno działania zespołowe...
-
WZROST ZATRUDNIENIA W PRZEDSIĘBIORSTWACH MSP problemy badawcze i wyniki
PublikacjaW artykule w pierwszej kolejności przedstawiono główne problemy badawcze związane z zagadnieniem wzrostu i rozwoju przedsiębiorstwa, wskazując na najczęściej stosowane rozwiązania metodyczne w tym zakresie. W dalszej części zaprezentowano wyniki badań empirycznych, dotyczące zmian zatrudnienia oraz planów związanych z rozwojem małych i średnich przedsiębiorstw funkcjonujących na Pomorzu (badania zostały przeprowadzone w 2009 i...
-
Metoda analizy wielokryterialnej do planowania rozwoju sieci elektroenergetycznej średniego i niskiego napięcia
PublikacjaW artykule przedstawiono metodę wspomagającą decyzje w zakresie wyboru wariantu przyłączenia odbioru do sieci elektroenergetycznej dystrybucyjnej niskiego napięcia lub średniego napięcia oraz mikrogeneracji do sieci niskiego napięcia. Metodę tą zaimplementowano w skoroszycie kalkulacyjnym Microsoft Excel i zastosowano do analizy złożonych przypadków przyłączenia odbioru lub mikrogeneracji.
-
Połączenie G3 dwóch kierunków prostych z użyciem krzywej NURBS
PublikacjaW artykule przedstawiono nową metodę projektowania układu geometrycznego toru kolejowego opartą na zastosowaniu krzywych NURBS (Non-Uniform Rational B-Spline) do opisu krzywizny. Punkty kontrolne krzywej NURBS wyznaczane są w procesie optymalizacji za pomocą algorytmu genetycznego. Jako kryterium optymalizacji przyjęto minimalizację oddziaływań dynamicznych występujących w układzie tor-pojazd przy spełnieniu warunków geometrycznych...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publikacja-
-
DoA Estimation Using Reconfigurable Antennas in Millimiter-Wave Frequency 5G Systems
PublikacjaTo achieve low latency and high throughputs, future 5G systems will have to utilize complex antenna systems able to provide beamforming and direction-of-arrival (DoA) estimation capabilities. Most of the concepts available in the literature rely on analog or digital beamforming, which is well developed and can be used both at a base station and in a user terminal. However, in applications, in which...
-
Optimizing CO2 Purification in a Negative CO2 Emission Power Plant
PublikacjaIn the pursuit of mitigating CO2 emissions, this study investigates the optimisation of CO2 purification within a Negative CO2 Emission Power Plant using a spray ejector condenser (SEC) coupled with a separator. The approach involves direct-contact condensation of vapour, primarily composed of an inert gas (CO2), facilitated by a subcooled liquid spray. A comprehensive analysis is presented, employing a numerical model to simulate...
-
Novel Tools for Comprehensive Functional Analysis of LDLR (Low-Density Lipoprotein Receptor) Variants
PublikacjaFamilial hypercholesterolemia (FH) is an autosomal-dominant disorder caused mainly by substitutions in the low-density lipoprotein receptor (LDLR) gene, leading to an increased risk of premature cardiovascular diseases. Tremendous advances in sequencing techniques have resulted in the discovery of more than 3000 variants of the LDLR gene, but not all of them are clinically relevant. Therefore, functional studies of selected variants...
-
Expedited Machine-Learning-Based Global Design Optimization of Antenna Systems Using Response Features and Multi-Fidelity EM Analysis
PublikacjaThe design of antenna systems poses a significant challenge due to stringent per-formance requirements dictated by contemporary applications and the high com-putational costs associated with models, particularly full-wave electromagnetic (EM) analysis. Presently, EM simulation plays a crucial role in all design phases, encompassing topology development, parametric studies, and the final adjustment of antenna dimensions. The latter...
-
Characteristics of La0.8Sr0.2Ga0.8Mg0.2O3-delta -supported micro-tubular solid oxide fuel cells with bi-layer and tri-layer electrolytes
PublikacjaIn this study, La0.8Sr0.2Ga0.8Mg0.2O3−δ (LSGM)-supported micro tubular solid oxide fuel cells (T-SOFCs) with two different configurations, one containing an LSGM–Ce0.6La0.4O2−δ (LDC) bi-layer electrolyte (Cell A) and one containing an LDC–LSGM–LDC tri-layer electrolyte (Cell B), were fabricated using extrusion and dip-coating. After optimizing the paste formulation for extrusion, the flexural strength of the dense and uniform LSGM...
-
Effective Formula for Impact Damping Ratio for Simulation of Earthquake-induced Structural Pounding
PublikacjaStructural pounding during earthquakes may cause substantial damage to colliding structures. The phenomenon is numerically studied using different models of collisions. The aim of the present paper is to propose an effective formula for the impact damping ratio, as a parameter of the impact force model used to study different problems of structural pounding under seismic excitations. Its accuracy has been verified by four various...
-
Potential Skyrmion Host Fe(IO3)3: Connecting Stereoactive Lone-Pair Electron Effects to the Dzyaloshinskii-Moriya Interaction
PublikacjaMagnetic skyrmions, which are topologically distinct magnetic spin textures, are gaining increased attention for their unique physical properties and potential applications in spintronic devices. Here we present a design strategy for skyrmion host candidates based on combinations of magnetic spin, asymmetric building units having stereoactive lone-pair electrons, and polar lattice symmetry. To demonstrate the viability of the proposed...
-
A system for singing training
PublikacjaThe system proposed is aimed at the vocal students and persons who want to improve emission of their voices. The goal is not to substituite a singing teacher but to provide a tool for automatic teaching of voice emission basics. In this way singers can develop their vocal skills and improve them. By a visual feedback a student can control and modify vocal tract maximas (resonances) of a chosen vowel to match the resonances of the...
-
Recent Advances in Graphene Oxide-Based Membranes for Heavy Metal Ions Separation
PublikacjaGraphene oxide (GO)-based membranes have been widely investigated for separation of dyes, salt ions, heavy metal ions, and biomolecules due to their high mechanical strength, single-layered structure, large surface area, and high affinity. However, due to irregular pore structure, nanochannels, interlayer distance, easy functionalization, swelling effect, and chemical stability under aqueous environment limited their separation...
-
A commercial gas boiler fitted with the ORC module as perspective solution for households
PublikacjaIn this paper the applicability of the commercial gas boiler (De Dietrich DTG X23N) coupled with the laboratory prototype micro ORC setup was experimentally studied. The main objective was to determine the working fluid capability to obtain required temperatures of vapour prior to the turbine, attainable heat rates and efficiencies of the whole system. The boiler thermal power was 25 kW. Tests were carried out with a single stage...
-
Supporting the development of clusters in Poland - dillemas faced by public policy
PublikacjaClusters have proved to be an important source of competitiveness for the economic development of regions within the European Union. In recent years many countries in the EU and throughout the world have launched policies aimed at supporting the development of clusters. There are many examples of good practices in the field of cluster policy, but there is no single model that can be applied in all countries and regions. This paper...
-
Induced sheath voltages in 110 kV power cables – case study
PublikacjaThis paper considers electric shock hazard due to induced sheath voltages in 110 kV power cables. The purpose of this paper is to find an optimal configuration of the power cable system, taking into account electric shock hazard and ability of the system to transfer maximal power. A computer simulations on a computer model of the local power system, comprising high voltage power cables, were carried out. This model enables to analyse...
-
Analysis of radiation and scattering problems with the use of hybrid techniques based on the discrete Green's function formulation of the FDTD method
PublikacjaIn this contribution, simulation scenarios are presented which take advantage of the hybrid techniques based on the discrete Green's function formulation of the finite-difference time-domain (DGF-FDTD) method. DGF-FDTD solutions are compatible with the finite-difference grid and can be applied for perfect hybridization of the FDTD method. The following techniques are considered: (i) DGF-FDTD for antenna simulations, (ii) DGF-based...