Wyszukiwarka
Filtry
wszystkich: 1320
wybranych: 1154
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MILLIMETER WAVES
-
Numerical analysis of elastic wave propagation in unbounded structures
PublikacjaThe main objective of this paper is to show the effectiveness and usefulness of the concept of an absorbing layer with increasing damping (ALID) in numerical investigations of elastic wave propagation in unbounded engineering structures. This has been achieved by the authors by a careful investigation of three different types of structures characterised by gradually increasing geometrical and mathematical description complexities....
-
Reservoir Influence on Pressure Wave Propagation in Steel Pipes
PublikacjaThe relation between the length of steel pipe and the pressure wave period in the system, reservoir-pipe-valve, is discussed. Experiments carried out for the short steel pipes showed that in such a system, the pressure wave celerity estimated using the measured wave cycles systematically increases with the increase of the pipe length. The observed differences can exceed even 90 m=s. As the pressure wave traveling in the pipe with...
-
Field-induced suppression of charge density wave in GdNiC2
PublikacjaWe report the specific heat, magnetic, magnetotransport, and galvanomagnetic properties of polycrystalline GdNiC 2 . In the intermediate temperature region above T N = 20 K, we observe large negative magnetoresistance due to Zeeman splitting of the electronic bands and partial destruction of a charge density wave ground state. Our magnetoresistance and Hall measurements show that at low temperatures a magnetic field-induced transformation from...
-
A concept of measurement system based on the Z-Wave standard
PublikacjaIn the paper a new concept of measurement system based on the Z-Wave standard is presented. This standard is dedicated to use mainly in home automation systems, but its properties enable to use it in dispersed measurement systems and support wireless communication between measurement nodes in a mesh-type network. In the paper basic metrological aspects of the Z-Wave standard and an example of impedance measurement system are discussed.
-
Investigation of continuous wave jamming in an IEEE 802.15.4 network
PublikacjaThis paper presents how continuous wave jamming affects IEEE 802.15.4 network. To this end, an office-based measurement setup has been proposed. Within the measurement area, 25 nodes have been set up in order to create a IEEE 802.15.4 tree-based test network structure. A dedicated jamming device that generates and transmits a continuous wave signal has been developed. Several tests have been conducted and presented to demonstrate...
-
Numerical modeling of the nonlinear wave propagation in a bubble layer
PublikacjaRozważano zagadnienie propagacji fali wewnątrz warstwy z pęcherzykami. Omówiono model matematyczny, przedstawiono przykładowe wyniki badań teoretycznych. Analizowano zmiany ciśnienia wewnątrz warstwy, falę odbitą i bieżącą w ośrodku otaczającym, badano gęstość widmową mocy. Badania teoretyczne przeprowadzono dla różnych grubości warstwy, koncentracji pęcherzyków i wartości parametrów fali padającej.
-
Wave transmission across surface interfaces in lattice structures
PublikacjaWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Measurement system based on USB Z-Wave controller
PublikacjaA wireless measurement system based on the Z-Wave standard is presented in this paper. The system is composed of a U SB Z-Stick Gen5 controller connected to a Personal Computer and a Fibaro controller FGRGBWM-441. Operation of the system is controlled by software written in C++ using OpenZWave library. Some metrological aspects of the system are evaluated: accuracy, linearity, resolution and frequency of voltage measurements.
-
Theoretical Model of Acoustic Wave Propagation in Shallow Water
PublikacjaThe work is devoted to the propagation of low frequency waves in a shallow sea. As a source of acoustic waves, underwater disturbances generated by ships were adopted. A specific feature of the propagation of acoustic waves in shallow water is the proximity of boundaries of the limiting media characterised by different impedance properties, which affects the acoustic field coming from a source situated in the water layer “ deformed”...
-
Lamb wave propagation in a single lap adhesive joint
PublikacjaThe aim of the paper is the analysis of Lamb wave propagation in adhesive joints. The research was performed on a single lap adhesive joint of two steel plates. Two types of joints, namely an intact and with defect were considered. In experimental investigations the condition assessment of the joint was performed with the use of antisymmetric Lamb waves excited by a plate piezo actuators and measured by a laser vibrometer. Numeri-cal...
-
Testing oscillators by waveform comparison with the ideal sine-wave
PublikacjaW kontekście oscylacyjnej metody testowania zaproponowano prostą i mało kosztowną metodę testowania oscylatorów poprzez porównanie fragmentu generowanego przebiegu z wzorcowym przebiegiem sinusoidalnym. Metoda bazuje na odejmowaniu dwu sygnałów zmodulowanych techniką sigma-delta za pomocą subtraktora wykorzystujacego nadpróbkowanie i kształtowanie szumów. Sygnaturą uszkodzeń jest wartość średnia 1 bitowego strumienia danych, wyznaczana...
-
Global value chains and labour markets – simultaneous analysis of wages and employment
PublikacjaThis study examines the overall effect of global value chains (GVCs) on wages and labour demand. It exploits the World Input–Output Database to measure GVC involvement via recently developed participation indices (using both backward and forward linkages) and the relative GVC position using three-stage least squares regression. We find that the relative GVC position is negatively correlated with wages and employment and that the...
-
Position in global value chains and wages in Central and Eastern European countries
PublikacjaThis paper examines the relationship between the relative position of industries in Global Value Chains (GVC) and wages in 10 Central and Eastern European countries. We combine GVC measures of global import intensity of production, upstreamness and the length of the value chain with micro-data on workers. We find that the wages of Central and Eastern European countries workers are higher when their industry is at the beginning...
-
Global value chains and wages under different wage setting mechanisms
PublikacjaThis study examines whether, and how, differences in wage bargaining schemes shape the relationship between global value chains (GVCs) and the wages of workers while considering both GVC participation and position in GVC. Our dataset is derived from the European Structure of Earnings Survey (SES), containing employee–employer data from 18 European countries, merged with sectoral data from the World Input-Output Database (WIOD)....
-
RMS-based damage identification in adhesive joint between concrete beam and steel plate using ultrasonic guided waves
PublikacjaAdhesive joints have numerous applications in many branches of industry, such as civil engineering, automotive, aerospace and shipbuilding. As with most structural elements, adhesive joints can experience any damage mechanism, which induces the need for diagnostic testing. Ultrasonic waves are widely used for non-destructive inspection of many structures and their elements, including adhesive joints. Guided wave propagation method...
-
Some new soliton solutions to the higher dimensional Burger–Huxley and Shallow water waves equation with couple of integration architectonic
PublikacjaIn this paper, we retrieve some traveling wave, periodic solutions, bell shaped, rational, kink and anti-kink type and Jacobi elliptic functions of Burger’s equation and Shallow water wave equation with the aid of various integration schemes like improved -expansion scheme and Jacobi elliptic function method respectively. We also present our solutions graphically in various dimensions.
-
Slow-wave fractal-shaped compact microstrip resonant cell
PublikacjaA novel fractal-shaped compact microstrip resonant cell (CMRC) featuring a strong slow-wave effect has been presented. Its vital usefulness in the process of microstrip line miniaturisation has been proved and experimentally validated on the basis of a compact 3-dB branch-line coupler illustrating the possibilities of the approach. A prototype example structure has been designed to mirror the characteristics of a conventional device,...
-
Numerical analysis of the finite amplitude plane wave propagation problem
PublikacjaRozważano zagadnienie propagacji fali płaskiej o skończonej amplitudzie w środowisku wodnym. Przedstawiono model matematyczny i przykładowe wyniki obliczeń numerycznych. Model matematyczny zbudowano w oparciu o równanie akustyki nieliniowej. Do rozwiązania zagadnienia zastosowano metodę różnic skończonych. Badano wpływ wartości parametrów numerycznych na dokładność obliczeń oraz analizowano wpływ wartości parametrów fizycznych...
-
Research on wave structures containing sets of metallized cylindrical objects
PublikacjaCel pracy obejmował opracowanie modelu matematycznego opartego na bezpośredniej interpretacji fizycznej rozpraszania fali elektromagnetycznej w zamkniętych i otwartych systemach zawierających różne konfiguracje złożonych obiektów cylindrycznych. Kolejnym celem było zastosowanie otrzymanego modelu do badania problemów otwartych i zamkniętych, oraz zaproponowanie przykładów ich aplikacji. Tezą pracy było stwierdzenie, że istnieje...
-
Radio wave propagation conditions for terrestrial radiocommunications in the EHF band
Publikacja -
Numerical modelling of conical wave formation in multimode optical fibers
Publikacja -
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Five-phase induction motor drive with sine-wave filter
PublikacjaThe paper presents closed loop ac drive with 5 phase induction motor operating with voltage source inverter and sine wave filter. The motor supply voltages and currents have sinusoidal shape. For well known adjustable electric drives the field oriented control method with flux and speed co ntrol can be applied. In the presence of output filter both control and estimation algorithms should be modified due to sine wave filter installation....
-
Diagnostics of bolted lap joint using guided wave propagation
PublikacjaThe paper presents numerical and experimental analyses of elastic waves propagation in a bolted lap joint. In experimental investigations condition assessment of the joint was performed with the use of symmetric waves excited by a piezoactuator. Numerical calculations were conducted in commercial finite element method software Abaqus. The influence of number of bolts and the value of the initial stress on recorded signals was examined....
-
Application of guided wave propagation in diagnostics of steel bridge components
PublikacjaEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
WAVE AND CURRENT MODELLING OVER THE BALTIC SEA AND THE GDAŃSK BAY
Publikacja -
Damage localisation in a stiffened plate structure using a propagating wave
PublikacjaThe paper presents an application of changes in propagating waves for damage detection in a stiffened aluminium plate. The experimental investigation was conducted on an aluminium plate with riveted two L-shape stiffeners. The wave has been excited with a piezoelectric transducer and measured with the Laser Scanning Doppler Vibrometer. Recorded signals were analysed using the special signal processing techniques developed for damage...
-
Scattering of the plane wave from a periodically perforated dielectric slab
Publikacja -
Evaluation of concrete cover by surface wave technique: Identification procedure
Publikacja -
Longitudinal wave propagation. Part I—Comparison of rod theories
Publikacja -
Longitudinal wave propagation. Part II—Analysis of crack influence
Publikacja -
Characteristics of the s–Wave Symmetry Superconducting State in the BaGe3 Compound
Publikacja -
Wave-induced pore pressure oscillations in sandy seabed sediments
PublikacjaPracę poświęcono zagadnieniu wywoływania cyklicznych oscylacji ciśnieniacieczy porowej w piaszczystym gruncie dna morskiego w wyniku oddziaływania progresywnego falowania powierzchniowego. Dokonano szerokiego przeglądu i analizy istniejących teorii ciśnień cieczy porowej z punktu widzenia skom- plikowania opisu matematycznego zachowania się ośrodka wodno-gruntowego. Wyprowadzono dwuwymiarowe rozwiązanie analityczne i...
-
Oblique Plane Wave Scattering by an Array of Dielectric and Metamaterial Cylinders.
PublikacjaBadanie wpływu ujemnej przenikalności elektrycznej i magnetycznej na parametry rozproszenia fali elektromagnetycznej dla cylindrów wykonanych z dielektryka i metamateriału. Wykorzystanie zmodyfikowanej procedury iteracyjnej i metody dopasowania rodzajów do analizy ukośnego padania fali elektromagnetycznej na zbiór równoległych cylindrów.
-
Spectral Wave Energy Dissipation due to Under-Ice Turbulence
Publikacja -
Square-wave propagation along coupled coplanar transmission line.
PublikacjaW pracy przedstawiono wyniki modelowania propagacji fali prostokątnej w układzie sprzężonych linii koplanarnych z uziemionym centralnym paskiem. Przeanalizowano napięcia przesłuchów na bliskim i dalekim końcu linii sprzężonych wykazując poprawę zgodności wyników modelowania i eksperymentu przy uwzględnieniu propagacji wielomodowej.
-
Damage Imaging in Lamb Wave-Based Inspection of Adhesive Joints
PublikacjaAdhesive bonding has become increasingly important in many industries. Non-destructive inspection of adhesive joints is essential for the condition assessment and maintenance of a structure containing such joints. The aim of this paper was the experimental investigation of the damage identification of a single lap adhesive joint of metal plate-like structures. Nine joints with different defects in the form of partial debonding...
-
Underwater Navigation System Based on Doppler Shifts of a Continuous Wave
PublikacjaThe paper describes a concept of an underwater navigation system designed to determine the location and speed of its ROVs or divers. Conducted by the Department of Marine Electronic Systems at the Gdansk University of Technology for several years, research has focused on navigation systems which determine positions on the basis of Doppler shifts of echo signals reflected from a moving object. This article presents a different version...
-
Nonlinear Properties of Seawater as a Factor Determining Nonlinear Wave Propagation
PublikacjaTaking practical advantage of nonlinear acoustical interactions occurring in seawater [1, 2] requires knowledge of the parameter of nonlinearity B=A of this medium. The literature does not offer much reports on B=A parameter value for seawater. In the few papers concerning that address the issue, results concerning ocean waters with high salinity and at large depths are given [3], while studies concerning seawater with low salinity...
-
Charge density wave and large nonsaturating magnetoresistance in YNiC2 and LuNiC2
PublikacjaWe report a study of physical properties of two quasi-low-dimensional metals YNiC2 and LuNiC2 including the investigation of transport, magnetotransport, galvanomagnetic, and specific heat properties. In YNiC2 we reveal two subsequent transitions associated with the formation of weakly coupled charge density wave at TCDW=318K and its locking in with the lattice at T1=275K. These characteristic temperatures follow the previously...
-
Detection of debonding in adhesive joints using Lamb wave propagation
PublikacjaAdhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form...
-
Domain Reduction in Hybrid Technique for Electromagnetic Wave Scattering Problems
PublikacjaThis paper proposes a combination of the field matching technique, finite element method and generalized impedance matrix, the main idea of which is to reduce the computational domain by surrounding a scatterer with the smallest convex shape and applying the field matching technique. This approach can be applied for arbitrary shaped scatterers and types of materials and allows for the reduction of the computational domain. In order...
-
Simulation of Wave Propagation in Media Described by Fractional-Order Models
PublikacjaIn this paper, algorithms for simulation of the wave propagation in electromagnetic media described by fractional-order (FO) models (FOMs) are presented. Initially, fractional calculus and FO Maxwell's equations are introduced. The problem of the wave propagation is formulated for media described by FOMs. Then, algorithms for simulation of the non-monochromatic wave propagation are presented which employ computations in the time...
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublikacjaDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
Preload monitoring in a bolted joint using Lamb wave energy
PublikacjaThe knowledge of the load in prestressed bolted connections is essential for the proper operation and safety of engineering structures. Recently, bolted joints have become an area of intensive research associated with non-destructive diagnostics, in particular in the context of wave propagation techniques. In this paper, a novel procedure of bolt load estimation based on the energy of Lamb wave signals was proposed. Experimental...
-
Analysis of guided wave propagation in adhesive joints of steel rods
PublikacjaThe aim of the study is the elastic wave propagation in adhesive joints of metal rods that are one of the simplest kind of glue connections. They are consisted of two metal members and an adhesive layer joining two parts together. The analysis is directed to technical diagnostics of such type of connections. Longitudinal and transversal guided waves were excited in prepared joints. Signals of propagating waves were registered in...
-
Multi-objective weather routing of sailboats considering wave resistance
PublikacjaThe article presents a method to determine the route of a sailing vessel with the aid of deterministic algorithms. The method assumes that the area in which the route is to be determined is limited and the basic input data comprise the wind vector and the speed characteristic of the vessel. Compared to previous works of the authors, the present article additionally takes into account the effect of sea waves with the resultant resistance...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublikacjaThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
-
Charge density wave and crystalline electric field effects in TmNiC2
PublikacjaSingle crystals of TmNiC2 were grown by the optical floating-zone technique and were investigated by x-ray diffraction (XRD), thermal expansion, electrical resistivity, specific heat, and magnetic susceptibility measurements. Single-crystal XRD reveals the formation of a commensurate charge density wave (CDW) characterized by a CDW modulation vector q2c = (0.5, 0.5, 0.5), which is accompanied by a symmetry change from the orthorhombic...
-
Nonlinear evolution of components of electromagnetic field of helicoidal wave in plasma
PublikacjaWyprowadzilismy model równań opisujących oddziaływanie pomiedzy kołowo spolaryzowanymi paczkami fal helikoidalnych w dwuwymiarowej plazmie. Dla quasi-jednowymiarowego przypadku otrzymaliśmy warunek nieliniowego rezonansu dla oddziaływania N-fal. Nowym ''osiągnięciem'' badań w kontekscie teorii solitonów, jest znalezienie rozwiązań dla przypadku asynchronizmu fal, które wydaje się być podstawowym dla paczek falowych nachylonych...