Filtry
wszystkich: 1368
wybranych: 907
-
Katalog
- Publikacje 907 wyników po odfiltrowaniu
- Czasopisma 97 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Osoby 101 wyników po odfiltrowaniu
- Aparatura Badawcza 1 wyników po odfiltrowaniu
- Kursy Online 120 wyników po odfiltrowaniu
- Wydarzenia 3 wyników po odfiltrowaniu
- Dane Badawcze 138 wyników po odfiltrowaniu
Filtry wybranego katalogu
Wyniki wyszukiwania dla: COACHING
-
Development of thin film SPME sorbents based on deep eutectic solvents and their application for isolation and preconcentration of endocrine-disrupting compounds leaching from diapers to urine
PublikacjaIn this study, the thin film solid phase microextraction (TF-SPME) based on a novel sorbent composed of deep eutectic solvent (DES) is proposed. Among several synthesized sorbents the most efficient was DES containing trihexyl(tetradecyl)phosphonium chloride and docosanol mixed with polydimethylsiloxane (PDMS) in a molar ratio 1:3:0.25 to achieve a more stable structure. The proposed sorbent was applied on a fiberglass mesh and...
-
Effect of alumina oxide nano-powder on the wear behaviour of CrN coating against cylinder liner using response surface methodology: processing and characterizations
Publikacja -
Understanding the Dominant Physics Mechanisms on the p-i-n Perovskite Solar Cells Fabricated by Scalable Slot-Die Coating Process in Ambient Air
PublikacjaPerovskite solar cells (PSC) are emerging technologies that have shown continuous improvement in power conversion efficiency (PCE) and stability. However, a very important aspect that has been seldom considered is the reproducibility of PCE of PSC devices. It is possible to achieve PCE from 10.21% to 17.05% using scalable slot-die-coating technique. However, a spatial distribution of performance is clearly observed for device samples...
-
The Influence of Long-Term Heat Treatment on Microstructure of Zr-Modified Aluminide Coating Deposited by CVD Method on MAR M200+Hf Nickel Superalloy
Publikacja -
Polyhydric SiO2 coating assistant to graft organophosphorus onto glass fabric for simultaneously improving flame retardancy and mechanical properties of epoxy resin composites
Publikacja -
Improvement of the Water Resistance of a Narrow-Band Red-Emitting SrLiAl3N4:Eu2+Phosphor Synthesized under High Isostatic Pressure through Coating with an Organosilica Layer
Publikacja -
Physicochemical properties of Mn1.45Co1.45Cu0.1O4 spinel coating deposited on the Crofer 22 H ferritic steel and exposed to high-temperature oxidation under thermal cycling conditions
PublikacjaThe Crofer 22 H ferritic steel substrate was coated with an Mn1.45Co1.45Cu0.1O4 spinel by means of electrophoresis. After high-temperature oxidation under thermal cycling conditions, the physicochemical properties of the obtained system were evaluated. During 48-h cycles that involved heating the samples up to temperatures of either 750 or 800 °C, the oxidation kinetics of both coated and unmodified steel approximately obeyed...
-
Cyclic behavior of FeCoCrNiMn high entropy alloy coatings produced through cold spray
PublikacjaeCoCrNiMn high entropy alloy powders were employed to produce coatings on carbon steel through high pressure cold spray (at 1100 °C and 7 MPa in temperature and pressure respectively). X-ray diffraction of the sprayed material revealed a dense coating with the retention of the original crystallographic structure. Once splatted, particles revealed high flattening ratio with consequent excellent adhesion of the coating to the substrate....
-
Comparison of Cu1.3Mn1.7O4 spinels doped with Ni or Fe and synthesized via wet chemistry and solid-state reaction methods, designed as potential coating materials for metallic interconnects
PublikacjaThe influence of the method applied to synthesize Cu-Mn-O spinel was evaluated. The methods selected for the investigation were EDTA gel processes and solid-state reaction synthesis. From the obtained powders, sinters were prepared and assessed in terms of their properties as potential coating materials. Additionally, the influence of Ni and Fe dopants was evaluated. The results show that the EDTA gel processes method seems to...
-
Wpływ odkształcenia na parametry stereometryczne powłok z faz międzymetalicznych NiAl i Ni3Al = Strain intensity effect on stereometrical properties at the NiAl i Ni3Al coating
PublikacjaWspółcześnie materiały na osnowie faz międzymetalicznych są przedmiotem badań wielu ośrodków naukowo-badawczych w kraju.Stopy na osnowie uporządkowanych faz międzymetalicznych z udziałem aluminium posiadają dużą odporność na utlenianie i korozję wżerową, a także wysoką wytrzymałość zmęczeniową oraz żaroodporność. Dlatego znalazły one zastosowanie do produkcji części maszyn do pracy w trudnych warunkach eksploatacyjnych (łopatki...
-
Design, engineering, and performance of nanorod-Fe2O3@rGO@LaSrFe2-Co O6 (n = 0, 1) composite architectures: The role of double oxide perovskites in reaching high solar to hydrogen efficiency
Publikacja -
Uwagi o problemach w nauczaniu projektowania i eksploatacji siłowni okrętowych (referat dyskusyjny) = Remarks on problems in teaching about designing and operating in ship power plant (discursive study).
PublikacjaW referacie uzasadniono celowość uwzględniania wybranych zagadnień projektowania siłowni w kształceniu studentów wydziałów mechanicznych akademii morskich i zagadnień eksploatacji siłowni w kształceniu studentów odpowiednich wydziałów politechnik.
-
Maszyny elektryczne wokół nas. Poszukiwanie dróg do nauczania na kierunku Elektrotechnika Politechniki Gdańskiej = Electrical machines around us. searching for teaching ways at electrical engineering of the Gdansk University of Technology
PublikacjaStreszczenie angielskie: This paper provides a summary of the didactic assumptions, goals and approach concerning the syllabus and description/modelling of electrical machines (EM) for teaching in the field of power electrical engineering at the Gdansk University of Technology. They have been used to write e-text book entitled "Electrical machines around us" that covered the lectures on electrical machines given for the second...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublikacjaVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...
-
Obyś cudze dzieci uczył! Magia zawodu czy przekleństwo wszech czasów? Na wstępie od redaktorki – bardzo osobiście [Teaching as such. A glamorous profession or a curse of all time? Some introductory remarks from the editor]
Publikacja -
The new silica-based coated SPME fiber as universal support for the confinement of ionic liquid as an extraction medium
PublikacjaThe new silica-based SPME fiber coating is reported for the first time as universal support purposed to confinement of ionic liquid as an extraction medium. Fiber coating was prepared by the sol-gel process, using potassium silicate (K2SiO3) as a precursor and dimethylformamide (DMF) as a pore-forming medium. The concept of synthesis assumes obtaining a solid porous material on the surface of the glass rod and, being characterized...
-
Geometrical versus analytical approach in problem solving- an exploatory study
PublikacjaAbstract. In this study we analyse the geometrical visualization as a part of the process of solution. In total 263 students in the first year of study at three different universities in three different countries (Poland, Slovakia and Spain) were asked to solve four mathematical problems. The analysis of the results of all students showed that geometrical visualization for problems where there is a possibility to choose different ways...
-
Porównanie efektywności wybranych technik ekstrakcji/ługowania metabolitów wtórnych z suchego materiału roślin owadożernych z hodowli in vitro = Acomparison of effciency of secondary metabolites extraction/leaching techniques from carnivorous plants dry material from in vitro culture
PublikacjaW roślinach owadożernych za efekt terapeutyczny odpowiadają głównie pochodne 1,4-naftochinonu (juglon), oraz flawonoidy. Interesujące właściwości tych związków oraz możliwość synergicznego działania wielu innych metabolitów na efekt terapeutyczny, podjęto pracę przygotowania technologii efektywnego wyodrębniania metabolitów. W tej publikacji porównano efektywności technik ekstrakcji/ługowania. Jako materiał badany posłużyły wysuszone...
-
The role of self-awareness in enhancing cooperative behaviour among students
Publikacja -
The role of self-awareness in enhancing cooperative behaviour among students
Publikacja -
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublikacjaHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Posttraumatic Orbital Emphysema: A Numerical Model
PublikacjaOrbital emphysema is a common symptom accompanying orbital fracture. The pathomechanism is still not recognized and the usually assumed cause, elevated pressure in the upper airways connected with sneezing or coughing, does not always contribute to the occurrence of this type of fracture. Observations based on the finite model (simulating blowout type fracture) of the deformations of the inferior orbital wall after a strike in...
-
Degradation of protective coatings in steel chimneys of flue gas desulfurisation system
PublikacjaThis paper presents problems associated with corrosion of steel stacks and changes in philosophy of corrosion protection when implemented into flue gas desulphurization systems. In-situ tests were taken by means of electrochemical impedance spectroscopy at the stack which discharges flue gas before wet lime/limestone desulphurization. A very quick electrolyte absorption by the spherical infill vinylester coating was found using...
-
Deterioration and Protection of Concrete Elements Embedded in Contaminated Soil: A Review
PublikacjaCoating materials are considered one of the most antique materials of human civilization; they have been used for decoration and the protection of surfaces for millennia. Concrete structures—due to their permanent exposure to different types of environments and contaminants—require the use of coatings that contribute to its preservation by reducing the corrosion of its components (steel and aggregates). This article intends to...
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti Substrate
PublikacjaThree coatings suitable for biomedical applications, including the dispersion coating composed of multi-wall carbon nanotubes (MWCNTs), MWCNTs/TiO2 bi-layer coating, and MWCNTs-Cu dispersion coating, were fabricated by electrophoretic deposition (EPD) on Ti Grade II substrate. Optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and nanoindentation were applied to study topography, chemical, and...
-
Low temperature processed MnCo2O4 and MnCo1.8Fe0.2O4 as effective protective coatings for solid oxide fuel cell interconnects at 750 °C
PublikacjaIn this study two materials, MnCo2O4 and MnCo1.8Fe0.2O4 are studied as potential protective coatings for Solid Oxide Fuel Cell interconnects working at 750 °C. First powder fabrication by a modified Pechini method is described followed by a description of the coating procedure. The protective action of the coating applied on Crofer 22 APU is evaluated by following the area specific resistance (ASR) of the scale/coating for 5500...
-
Performance of zinc-rich coatings evaluated using AFM-based electrical properties imaging
PublikacjaThe paper presents the results of investigation of polyvinyl zinc-rich coating exposed to 97% relativehumidity atmosphere for 40 days. Condition of the coating and evolution of its protective properties weredetermined with the novel AFM-based approach capable of providing surface profiles, local dc currentmaps as well as local impedance spectra. The proposed technique allowed insight into the local changesof coating topography...
-
Manganese Phosphatizing Coatings: The Effects of Preparation Conditions on Surface Properties
PublikacjaManganese phosphate coating could be used to protect the surface of steel products. However, it is essential to determine the effects which process parameters, as well as the types of additives used, have on the efficiency of coating deposition. Thus, we present here a process of phosphatization of low-alloy steel (for 15 min at 95 ◦C) in manganese/nickel baths followed by a passivation process with the use of a silicon and zircon...
-
Measurement methods for assessing insulation condition of underground pipelines
PublikacjaThe paper discusses the most frequently applied measurement methods for assessing the quality of external insulation along pipelines and detecting defect locations in the protective coating. The quality of coating along a given pipeline section under investigation is assessed by determining unitary resistance of the coating, which is calculated on the basis of measurement results obtained along a pipeline subjected to cathodic...
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublikacjaSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
Adhesion of organic coatings to hot-dip galvanized steel
PublikacjaDuplex systems provide long-time corrosion protection, much longer than the sum of the lifetimes of zinc and paint used individually. However loss of adhesion between coating and zinc substrate is often found in practice. Different methods of zinc surface preparations are used in the fi eld. The aim of this study was to examine and compare coating protection when the old zinc surface, stored during long-time period (15 years) in...
-
Developing competences for cooperation in international teams - tools and methods
PublikacjaThe article presents the training methods that can be used to develop intercultural competences which are extremely important while working in intercultural teams. The mentioned methods like: case-studies, collaborating, role-play simulations, team working, video presentations and others are presented on the basis of authors’ experiences while teaching the international groups of students at Faculty of Management and Economics...
-
Otwarte zasoby edukacyjne - przegląd inicjatyw w Polsce i na świecie
PublikacjaOtwarte zasoby edukacyjne (OZE) to materiały szkoleniowe oraz narzędzia wspierające zarówno uczenie, jak i nauczanie. Zjawisko to nierozerwalnie łączy się z szerszym pojęciem otwartej edukacji (OE), które postuluje zniesienie barier w nauczaniu tak, aby uczący się mogli zdobywać wiedzę zgodnie ze swoimi potrzebami edukacyjno-szkoleniowymi. Celem artykułu jest zapoznanie czytelników z zagadnieniem otwartych zasobów edukacyjnych,...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublikacjaCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
Nickel-nanodiamond coatings electrodeposited from tartrate electrolyte at ambient temperature
PublikacjaIn this study, nanocrystalline Ni and Ni-diamond coatings were obtained by electrodeposition from tartrate electrolyte at ambient temperature aiming at improving corrosion and wear properties of the material. The created surfaces were investigated with regard to microhardness, adhesion, wear- and corrosion-resistance. The various methods such as atomic force microscopy, scanning electron microscopy, electrochemical impedance spectroscopy...
-
Pharmaceutical care in the neonatal intensive care unit: Perspectives of Polish medical and pharmacy students
Publikacja -
The use of eLearning strategies among travel agents in the United Kingdom, India and New Zealand
Publikacja -
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublikacjaThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
New Transparent Flame-Retardant (FR) Coatings Based on Epoxy-Aluminum Hypophosphite Nanocomposites
PublikacjaThe present study investigated the flame-retardant (FR) effect of transparent epoxy coating containing aluminum hypophosphite (AHP) nanoparticles (NPs) on polylactic acid (PLA) sheets used as a typical model of combustible polymeric material. First, AHP NPs (≤60 nm) were prepared by a specific two-stage wet milling process and deeply analyzed (morphology, thermal/mechanisms of degradation under nitrogen and air). The thermal properties...
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublikacjaMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
Stratification of nano-pigments in anti-corrosive coatings by means of magnetic field
PublikacjaThe concept of self-stratification of coatings, although attractive, causes difficulties in its practical use, especially when pigments are added to the resins. An alternative way of obtaining a multilayer structure in a single step was presented. Using the inhomogeneous magnetic field and magnetically active components of the coating, the possibility of vertically graded differentiation of the one layer properties has been verified....
-
Chosen Methods Supporting Didacts of Descriptive Geometry
PublikacjaThe article presents reflections on the practical ways of supporting the teaching processes of descriptive geometry in the context of psychological theories of learning and motivation.
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Environmental degradation of Ti alloys in artificial saliva and a role of fluorides
PublikacjaThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Environmental degradation of titanium alloy in artificial saliva
PublikacjaThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Structural evaluation of percolating, self-healing polyurethane–polycaprolactone blends doped with metallic, ferromagnetic, and modified graphene fillers
PublikacjaComposites with differently shaped micro- and nanofillers show various, unique thermal, and physicochemical properties when mixed with carefully chosen polymer matrix. Selected composition holds strategic value in achieving desired properties that is biodegradability, thermoelectric conductivity, and shape memory for organic coating. The main aim of this work is to briefly examine structural changes after reaching percolation...
-
Structural evaluation of percolating, self-healing polyurethane–polycaprolactone blends doped with metallic, ferromagnetic, and modified graphene fillers
PublikacjaComposites with differently shaped micro- and nanofillers show various, unique thermal, and physicochemical properties when mixed with carefully chosen polymer matrix. Selected composition holds strategic value in achieving desired properties that is biodegradability, thermoelectric conductivity, and shape memory for organic coating. The main aim of this work is to briefly examine structural changes after reaching percolation threshold...
-
Evaluation of organic coatings condition with AFM-based method
PublikacjaThe paper presents an atomic force microscopy (AFM)-based approach to evaluation of local protective properties of organic coatings. Apart from topography, it provides local ac and dc characteristics of examined coating. The method consists in application of ac voltage perturbation signal between conductive AFM tip and coated metal substrate. The resulting current is used to determine local impedance characteristics. Both impedance...
-
Applicability of edible Candelilla wax composite blended with Bryophyllumpinnatum extract to prolong shelf life of fruits/vegetables
PublikacjaCandelilla wax (CW) is a natural lipid source that can be used to make biodegradable and edible coatings and films for fruits. However, CW alone does not provide sufficient antimicrobial and antioxidant properties to prevent microbial spoilage and oxidative deterioration of fresh products. This study aims at evaluating the applicability of CW blended with Bryophyllum pinnatum extract (BPE), a plant with medicinal and phytochemical...
-
Weldability of high strength steels in wet welding conditions
PublikacjaIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...