Filtry
wszystkich: 1001
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: ROOF RUNOFF
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublikacjaThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
PROGRAMMABLE YANG - BASED INTERFACE IN CONTROL OF OPTICAL TRANSPORT NETWORK
PublikacjaSince over a decade we observe intensive effort of research institutions and industrial consortia on extending flexibility and automation of the transport network control also known under the term network programmability. Key aspect of each programming interface is ability to evolve but also sensitivity to future modifications. As indicated in the past work in the specific context of optical transport networks an important criterion...
-
STUDIES ON THE USE OF TERRESTRIAL LASER SCANNING IN THE MAINTENANCE OF BUILDINGS BELONGING TO THE CULTURAL HERITAGE
PublikacjaWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith’s forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Studies on the use of terrestrial laser scanning in the maintenance of buildings belonging to the cultural heritage
PublikacjaWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith's forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Mössbauer Spectroscopy and Magnetoelectric Effect Studies of Multiferroic Ceramics Based on BiFeO<sub>3</sub>
PublikacjaIn this work the results of investigations for (BiFeO3)x(BaTiO3)1-x and Bi1-xNdxFeO3 solid solutions are described. Samples were prepared by the conventional solid-state sintering method. X-ray diffraction, 57Fe Mössbauer spectroscopy, and magnetoelectric effect measurements were applied as complementary methods to determine the structure and magnetic properties of materials. For (BiFeO3)x(BaTiO3)1-x solid solutions Mössbauer...
-
Resistive gas sensors – Perspectives on selectivity and sensitivity improvement
PublikacjaResistive gas sensors are very popular and relatively inexpensive; they can operate at elevated or room temperature for years on end. The main disadvantage of resistive gas sensors is their limited selectivity and sensitivity, but various methods have been applied to improve their behavior. The composition of the porous gas sensing layer, or changes in the sensor’s operating temperature, can enhance the gas detection ability. Furthermore, emerging...
-
Industry 4.0 Implementation Challenges in Manufacturing Industries: an Interpretive Structural Modelling Approach
PublikacjaFor the last few years, the fourth industrial revolution, known as Industry 4.0, has been a hot topic among academics. Industry 4.0 literature involves researches presenting studies related to its different aspects including challenges, opportunities, implementation and adoption. However, a detailed study of challenges and barriers towards the Industry 4.0 implementation in manufacturing industries is missing. Hence, this paper...
-
Vibration-Based Investigation of a Historic Bell Tower to Understand the Occurrence of Damage
PublikacjaABSTRACT The paper presents a survey of the historic Arch-cathedral bell tower in Vilnius induced by the appearance of cracks in the structure after a new bell system installation. An attempt is undertaken to identify the reason for the crack occurrence and to check a possible crack influence on global structural behaviour. The research is based on dynamic measurements made in the tower during ambient vibrations and during vibrations...
-
Nanoindentation tests titanium alloy Ti-6Al-4V after interference laser treatment
PublikacjaThe study aimed was to assess selected mechanical properties of surface layers obtained after interference laser treatment – DLIL of titanium alloy Ti-6Al-4V used for implants. The samples were melted in still air at room temperature, for this purpose Nd:YAG laser was used, the number of laser shots was variable. Next, nanoindentation tests were performed, based on which Young’s modulus and nanohardness in the obtained surface...
-
Stability analysis of interconnected discrete-time fractional-order LTI state-space systems
PublikacjaIn this paper, a stability analysis of interconnected discrete-time fractional-order (FO) linear time-invariant (LTI) state-space systems is presented. A new system is formed by interconnecting given FO systems using cascade, feedback, parallel interconnections. The stability requirement for such a system is that all zeros of a non-polynomial characteristic equation must be within the unit circle on the complex z-plane. The obtained...
-
Collaborative Exploration of Trees by Energy-Constrained Mobile Robots
PublikacjaWe study the problem of exploration of a tree by mobile agents (robots) that have limited energy. The energy constraint bounds the number of edges that can be traversed by a single agent. We use a team of agents to collectively explore the tree and the objective is to minimize the size of this team. The agents start at a single node, the designated root of the tree and the height of the tree is assumed to be less than the energy...
-
Chemometric Evaluation of WWTPs’ Wastewaters and Receiving Surface Waters in Bulgaria
PublikacjaWastewater treatment plant (WWTP) installations are designed and operated to reduce the quantity of pollutants emitted to surface waters receiving treated wastewaters. In this work, we used classical instrumental studies (to determine chemicals and parameters under obligations put with Directive 91/271/EEC), ecotoxicological tools (Sinapis alba root growth inhibition (SA-RG) and Heterocypris incongruens mortality (MORT) and growth...
-
Preparation of Allyl Alcohol Oligomers Using Dipicolinate Oxovanadium(IV) Coordination Compound
PublikacjaCurrently, new precatalysts for olefin oligomerization are being sought in the group of vanadium(IV) complexes. Thus, the aim of our research was to examine the catalytic activity of the oxovanadium(IV) dipicolinate complex [VO(dipic)(H2O)2] 2 H2O (dipic = pyridine-2,6-dicarboxylate anion) in 2-propen-1-ol oligomerization as well as to characterize oligomerization products using matrix-assisted laser desorption/ionization–time-of-flight...
-
Featured based CAVE software factory
PublikacjaIn the paper we convey the lessons learned along the path we have gone through several years since establishing a room-sized CAVE installation at our university, from craft manufacturing and ad-hoc software reuse of VR software products to the robust feature driven software product line (SPL) implementing the Product Line Engineering (PLE) factory paradigm. With that we can serve all our departments and other entities from the...
-
Practical Eco-Driving Strategy for Suburban Electric Multiple Unit
PublikacjaIn this paper, a practical approach to velocity profile optimization for electric multiple unit was presented. The study focuses on a case of fast urban railway, which is a popular mean of transport across Tricity, Poland. Based on observations and measurements, a potential for improvement of energy efficiency by modifying the speed profile was recognized. In order to conduct necessary calculations, simulation model of railway...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublikacjaAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
Recent advances in hydrodynamic cavitation-based pretreatments of lignocellulosic biomass for valorization
PublikacjaRecently, the hydrodynamic cavitation (HC)-based pretreatment has shown high effectiveness in laboratories and even in industrial productions for conversion of lignocellulosic biomass (LCB) into value-added products. The pretreatment capability derives from the extraordinary conditions of pressures at ∼500 bar, local hotspots with ∼5000 K, and oxidation (hydroxyl radicals) created by HC at room conditions. To promote this emerging...
-
Damage imaging algorithm for non-destructive inspection of CFRP/steel adhesive joints based on ultrasonic guided wave propagation
PublikacjaThe paper concerns assessing the quality of the adhesive connection between a steel plate and the reinforcing CFRP laminate. A three-stage algorithm for non-destructive damage imaging was developed. As the first step, an initial study involving dispersion curves of joint components was executed to determine the material parameters and the appropriate excitation frequency. During the second step, damage identification in three-layer...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublikacjaGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Towards truly sustainable IoT systems: the SUPERIOT project
PublikacjaThis paper provides an overview of the SUPERIOT project, an EU SNS JU (Smart Networks and Services Joint Undertaking) initiative focused on developing truly sustainable IoT systems. The SUPERIOT concept is based on a unique holistic approach to sustainability, proactively developing sustainable solutions considering the design, implementation, usage and disposal/reuse stages. The concept exploits radio and optical technologies...
-
Anna Rzeczycka dr hab.
OsobyAnna Rzeczycka jest zastępcą kierownika Katedry Finansów na Wydziale Ekonomii i Zarządzania Politechniki Gdańskiej. Publikacje sytuują się w dziedzinie nauk społecznych w zakresie dyscypliny ekonomia i finanse. Obejmują one książki, monografie, artykuły, publikacje i redakcje naukowe monografii i zeszytów naukowych. Liczbowo obejmuje on następujące pozycje: 12 monografii i podręczników, 115 publikacji w czasopismach naukowych,...
-
Low-Voltage Low-Power Filters with Independent ω0 and Q Tuning for Electronic Cochlea Applications
PublikacjaAn acoustic second-order low-pass filter is proposed for filter banks emulating the operation of a human cochlea. By using a special filter structure and an innovative quality (Q)-factor tuning technique, an independent change of the cutoff frequency (ω0) and the Q-factor with unchanged gain at low frequencies is achieved in this filter. The techniques applied result in a simple filter design with low Q-factor sensitivity to component...
-
Anna Baj-Rogowska dr
OsobyAnna Baj-Rogowska zatrudniona jest na stanowisku adiunkta w Katedrze Informatyki w Zarządzaniu (Politechnika Gdańska, Wydział Zarządzania i Ekonomii). Jej wyższa edukacja związana jest z Uniwersytetem Gdańskim, gdzie ukończyła magisterskie studia informatyczne, studia doktoranckie i następnie uzyskała stopień naukowy doktora nauk ekonomicznych w zakresie nauk o zarządzaniu (Katedra Informatyki Ekonomicznej na Wydziale Zarządzania...
-
The structure of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides measured with X-ray diffraction method
Dane BadawczeThe structure of strontium–borate glasses and glass-ceramics containing bismuth and vanadium oxides was measured by XRD.
-
The structure of strontium–borate glass-ceramics containing crystalites of Bi2VO5.5. measured with X-ray diffraction and SEM methods
Dane BadawczeThe structure of strontium–borate glass-ceramics containing Bi2VO5.5 crystallites was measured by XRD and SEM.
-
Zaufanie do siebie jako jeden z aspektów zaufania w aktywności przedsiębiorczej
PublikacjaArtykuł prezentuje znaczenie zaufania do samego siebie na tle zaufania w relacjach budowanych przez przedsiębiorcę w jego otoczeniu społecznym i biznesowym. Wyjaśniono koncepcję zaufania do samego siebie, odnosząc się do zróżnicowanych typów zaufania, na przykład: kalkulacyjnego, opartego na wiedzy i identyfikacyjnego. Wskazano jego potencjalne źródła i konsekwencje w kontekście budowania własnego wizerunku, podejmowania decyzji...
-
The Mott-Schottky characteristics of microwave pulsed-plasma polymerized allylamine by DEIS analysis
Dane BadawczeThe dataset contains the results obtained for the Mott-Schottky analysis of the microwave pulsed-plasma polymerized allylamine using the multifrequency perturbation signal with Dynamic Electrochemical Impedance Spectroscopy (DEIS) technique. The results were obtained using the perturbation composed of the elementary signals with a frequency range between...
-
Wind speed, wind direction and solar radiation datasets; wind and solar energy resources analysis
Dane BadawczeDataset contain the results of wind speed, wind direction and solar radiation for wind and solar energy resources analysis performed in years 2008 and 2009. Application for efficiency and profitability of solar and wind power plants anaylsis and for energy generation forecasting algorithms design and anaysis. Datasets used in doctoral dissertations,...
-
Depth profile of the composition of 8 nm Al2O3 thin film
Dane Badawcze8 nm layer of aluminum oxide (Al2O3) was deposited by ALD method on a s. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. To investigate the profile of concenration of...
-
Mariusz Franciszek Kaszubowski dr
OsobyBiogram Mariusz Kaszubowski jest adiunktem w Katedrze Statystyki i Ekonometrii Wydziału Zarządzania i Ekonomii Politechniki Gdańskiej. Prowadzi zajęcia ze statystyki opisowej i matematycznej, a także statystyki społecznej i statystyki ubezpieczeniowej. Wykłada również statystykę na podyplomowych studiach z kontroli jakości „Lean Six Sigma Black Belt”. Jest absolwentem dwóch kierunków studiów: Zarządzania (specjalność Statystyka...
-
Managing the security vulnerabilities of critical systems and hazardous plants
PublikacjaRozdział poświęcono aktualnym problemom zarządzania ochroną obiektów podwyższonego ryzyka jako ważnych systemów infrastruktury krytycznej. Zarządzanie odpornością na ataki takich obiektów jest oparte na ocenach ryzyka. Podkreśla się, że występują ważne instalacje i systemy wymagające specjalnej uwagi i zabezpieczeń, szczególnie systemy kontroli dostępu do sterowni i urządzeń komunikacji. Opisuje się przykładowe technologie ochrony....
-
MOOCs in SP4CE - case studies (Strategic Partnership for Creativity and Entrepreneurship)
PublikacjaSP4CE stands for Strategic Partnership for Creativity and Entrepreneurship project which has been funded with support from the European Commission under the ERASMUS+ Programme in the period 1st September 2014 - 31st August 2017. The main purpose of SP4CE project is to design innovative e-learning tools for collaboration between students, enterprises and teachers. It concentrates on identifying users’ needs and supports the development...
-
Circularly Polarized Metalens Antenna Design for 5G NR Sub-6 GHz Communication Systems
Publikacja5G NR (new radio) FR1 range refers to as Sub-6GHz band (410MHz to 7125MHz and 3.4GHz to 6GHz). In this paper, the frequency range of interest is from 3.4 to 6GHz, as many cellular companies are focusing on this Sub-6GHz band. A wideband circularly polarized (CP) antenna radiator is designed with diamond shape patches, fed by a microstrip line at the bottom through a rectangular shape wide slot on a ground plane. The proposed CP...
-
INVESTIGATION OF THE LOMBARD EFFECT BASED ON A MACHINE LEARNING APPROACH
PublikacjaThe Lombard effect is an involuntary increase in the speaker’s pitch, intensity, and duration in the presence of noise. It makes it possible to communicate in noisy environments more effectively. This study aims to investigate an efficient method for detecting the Lombard effect in uttered speech. The influence of interfering noise, room type, and the gender of the person on the detection process is examined. First, acoustic parameters...
-
Miniaturized Inline Bandpass Filters Based on Triple-Mode Integrated Coaxial-Waveguide Resonators
PublikacjaThis work presents a design technique to implement miniaturized cross-coupled bandpass filters in inline physical configurations based on triple-mode resonators. Triple-mode resonances are obtained by using integrated coaxial-waveguide cavity resonators. They consist of two coaxial conducting posts placed in the sidewalls of a rectangular waveguide cavity. In the proposed triplet, a transmission zero (TZ) can be positioned at any...
-
Ultrafast high-temperature sintering (UHS) of cerium oxide-based compound
PublikacjaUltrafast high-temperature sintering (UHS) is an innovative sintering technique that can densify ceramics in a few seconds, dramatically reducing the carbon footprint and firing costs. In this work, the feasibility of applying UHS in Gd-doped ceria (GDC) and GDC-Er-stabilized bismuth oxide (ESB) composite powders was investigated. At high UHS currents (22-24 A), a fully dense GDC sample with a large grain size was obtained. Nonetheless,...
-
Isolation and structure of a covalent cross-link adduct between mitomycin C and DNA
PublikacjaA DNA cross-link adduct of the antitumor agent mitomycin C (MC) to DNA has been isolated and characterized; the results provide direct proof for bifunctional alkylation of DNA by MC. Exposure of MC to Micrococcus luteus DNA under reductive conditions and subsequent nuclease digestion yielded adducts formed between MC and deoxyguanosine residues. In addition to the two known monoadducts, a bisadduct was obtained. Reductive MC activation...
-
Rospuda - czy wszędzie budować mosty?
PublikacjaStreszczenie - SummaryThe article presents the problem of planning transport system in the areas of high natural and landscape values. Bridges and roads crossing valuable areas undergo Environmental Impact Assessment (EIA) Procedure. This procedure in Poland is often treated only as formal requirement, not as an instrument helping to solve conflicts and to minimise negative environmental and landscape effects. The potential of...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Influences of grain shape and size distribution on permeability
PublikacjaThe present study investigates the effects of shape and size distributions of grains on the coefficient of permeability (k). A series of constant head permeability tests were performed to characterize the coefficient of permeability. Three particle size ranges (4.75- 0.075, 1.18- 0.075 and 0.300-0.075 mm) of two different sands (Narli Sand, Crushed Stone Sand) having different shapes were tested in a constant head permeability...
-
Polyurethane glycolysate from industrial waste recycling to develop low dielectric constant, thermally stable materials suitable for the electronics
PublikacjaWe are utilizing a new method to improve the dielectric properties of a conventional polymer using a recycled polymer product. The polyurethane foams are recycled by glycolysis process and the derived material was applied to improve the dielectric properties of the brittle DGEBA epoxy resin. Two main parameters that determine the applicability of the material as a dielectric (the dielectric constant and dielectric loss), were studied...
-
Damage Imaging in Lamb Wave-Based Inspection of Adhesive Joints
PublikacjaAdhesive bonding has become increasingly important in many industries. Non-destructive inspection of adhesive joints is essential for the condition assessment and maintenance of a structure containing such joints. The aim of this paper was the experimental investigation of the damage identification of a single lap adhesive joint of metal plate-like structures. Nine joints with different defects in the form of partial debonding...
-
Machine Learning Algorithm-Based Tool and Digital Framework for Substituting Daylight Simulations In Early- Stage Architectural Design Evaluation
PublikacjaThe aim of this paper is to examine the new method of obtaining the simulation-based results using backpropagation of errors artificial neural networks. The primary motivation to conduct the research was to determine an alternative, more efficient and less timeconsuming method which would serve to achieve the results of daylight simulations. Three daylight metrics: Daylight Factor, Daylight Autonomy and Daylight Glare Probability have...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublikacjaThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
A Novel IoT-Perceptive Human Activity Recognition (HAR) Approach Using Multi-Head Convolutional Attention
PublikacjaTogether with fast advancement of the Internet of Things (IoT), smart healthcare applications and systems are equipped with increasingly more wearable sensors and mobile devices. These sensors are used not only to collect data, but also, and more importantly, to assist in daily activity tracking and analyzing of their users. Various human activity recognition (HAR) approaches are used to enhance such tracking. Most of the existing...
-
Electric and magnetic properties of Lanthanum Barium Cobaltite
PublikacjaThe cubic Ba0.5La0.5CoO3‐δ was synthesized using solid state reaction. The structural properties were determined by the simultaneous refinement of Synchrotron Powder X‐ray Diffraction and Neutron Powder Diffraction data. Iodometric titration was used to examine the oxygen stoichiometry and average cobalt oxidation state. Low‐temperature magnetic studies show soft ferromagnetic character of fully oxidized material, with θP = 198(3)...
-
Application of Stirling Engine Type Alpha Powered by the Recovery Energy on Vessels
PublikacjaThe Stirling engine is a device, in which thermal energy is transformed into mechanical without a contact between the heat carrier, and the working gas closed in the engine. Mentioned feature makes this type of engine very attractive for the use of the recovery energy, taken from other heat devices. One of the potential applications of Stirling engines is the use of thermal energy generated in the ship's engine room for producing...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublikacjaThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
CAUSALITY IN MODELS OF THERMAL PROCESSES IN SHIP ENGINE ROOMS WITH THE USE OF BOND GRAPH (BG) METHOD
PublikacjaWith a single approach to modeling elements of different physical nature, the method of Bond Graph (BG) is particularly well suited for modeling energy systems consisting of mechanical, thermal, electrical and hydraulic elements that operate in the power system engine room. The paper refers to the earlier presented new concept of thermal process modeling using the BG method. The authors own suggestions for determining causality...
-
Tuning the photocatalytic performance through magnetization in Co-Zn ferrite nanoparticles
PublikacjaIn this work, the link between the photocatalytic performance of Co-Zn ferrite nanoparticles and the net magnetic moment is analyzed. CoxZn1-xFe2O4 nanoparticles (0 ≤ x ≤ 1) were synthesized by co-precipitation method and different physicochemical techniques were employed to characterize the samples (X-ray diffraction, Transmission Electron Microscopy (TEM), BET surface area, Diffuse Reflectance Spectroscopy (DRS), Photoluminescence spectroscopy,...