Wyszukiwarka
Filtry
wszystkich: 1625
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: TAGGING
-
Przegląd metod monitorowania stanu technicznego tranzystorów mocy
PublikacjaW artykule przedstawiono kilka metod monitorowania stanu technicznego tranzystorów mocy, które są lub mogą być wbudowane w układy przekształtnikowe. Celem artykułu jest określenie aktualnego stanu badań na ten temat. Prezentowane metody przeznaczone są do monitorowania istotnych objawów starzenia modułów mocy: rozwarstwiania struktury modułu na skutek termomechanicznego zmęczenia stopu lutowniczego, uszkodzeń połączeń drutowych...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublikacjaIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulationand evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modelingand solution rely on finite element methods and cover the simulation of the structure’s properties along with the influenceof the marine environment – sea currents, wave...
-
Maximum Power Point Technique (MPPT) for PV System Based on Improved Pert and Observe (P&O) Method with PI Controller
PublikacjaPhotovoltaic power generation system has key rule in electricity production. Although, it is clean renewable energy with unlimited resources but it has some drawbacks in efficiency. In order to maximize the efficiency, PV array must drive at maximum power point. For the reason so, several algorithms are used in PV system to track MPP and reduce the...
-
Conductivity, structure, and thermodynamics of Y2Ti2O7–Y3NbO7 solid solutions
PublikacjaThe defect fluorite yttrium niobate Y3NbO7 and pyrochlore yttrium titanate Y2Ti2O7 solid solutions have been synthesized via a solid state synthesis route. The resulting stoichiometry of the oxides is Y2+xTi2−2xNbxO7, where x = 0 to x = 1. All of the samples were single-phase; however, for those with a predominant fluorite phase, a small amount of additional pyrochlore phase was detected. The volume of the solid solution unit cells...
-
Effects of Bromine Doping on the Structural Properties and Band Gap of CH3NH3Pb(I1–xBrx)3 Perovskite
PublikacjaAn experimental and theoretical study is reported to investigate the influence of bromine doping on CH3NH3Pb(I1−xBrx)3 perovskite for Br compositions ranging from x = 0 to x = 0.1, in which the material remains in the tetragonal phase. The experimental band gap is deduced from UV−vis absorption spectroscopy and displays a linear behavior as a function of bromine concentration. Density functional theory calculations are performed...
-
Down-Sampling of Large LiDAR Dataset in the Context of Off-Road Objects Extraction
PublikacjaNowadays, LiDAR (Light Detection and Ranging) is used in many fields, such as transportation. Thanks to the recent technological improvements, the current generation of LiDAR mapping instruments available on the market allows to acquire up to millions of three-dimensional (3D) points per second. On the one hand, such improvements allowed the development of LiDAR-based systems with increased productivity, enabling the quick acquisition...
-
Uncertainty Quantification in Experimental Structural Dynamics Identification of Composite Material Structures
PublikacjaComposite materials are widely used in manufacture of aerospace and wind energy structural components. These load carrying structures are subjected to dynamic time-varying loading conditions. Robust structural dynamics identification procedure impose tight constraints on the quality of modal models estimates obtained from vibration experiments. Modal testing results are influenced by numerous factors introducing uncertainty to...
-
E-Learning Service Management System For Migration Towards Future Internet Architectures
PublikacjaAs access to knowledge and continuous learning are among the most valuable assets in modern, technological society, it is hardly surprising that e-learning solutions can be counted amongst the most important groups of services being deployed in modern network systems. Based on analysis of their current state-of-the-art, we decided to concentrate our research and development work on designing and implementing a management system...
-
The OptD-multi method in LiDAR processing
PublikacjaNew and constantly developing technology for acquiring spatial data, such as LiDAR (light detection and ranging), is a source for large volume of data. However, such amount of data is not always needed for developing the most popular LiDAR products: digital terrain model (DTM) or digital surface model. Therefore, in many cases, the number of contained points are reduced in the pre-processing stage. The degree of reduction is determined...
-
Linear and nonlinear impedance in iron oxide glasses containing alkaline ions and alkali free
PublikacjaThe linear and nonlinear impedance spectra of oxide glasses were measured in the frequency range of 1 mHz to 1 MHz and in the temperature range of 153K to 483K. Two groups of iron oxide glass samples were prepared, the first one containing alkaline ions and the second one without alkali. In the first group, compositions of glasses were as follows: (in %mol) 50% SiO2 , 25% PbO, 15% Fe2O3 and 15% one of alkaline oxides: Na2O, K2O,...
-
Design of Microwave-Based Angular Displacement Sensor
PublikacjaThis letter presents a novel microwave-based rotation sensor having a wide dynamic range to detect and measure the angular displacement in terms of the change in resonant frequency. The proposed sensor is based on the microstrip technology, where a rotor comprised of a complementary splitring resonator (CSRR) placed on the ground plane of the microstrip line is free to rotate around its axis. The mechanical rotation of CSRR determines...
-
3D Vision System for a Robotic Arm Based on Equal Baseline Camera Array
PublikacjaThis paper presents a lightweight 3D vision system called Equal Baseline Camera Array (EBCA). EBCA can work in different light conditions and it can be applied for measuring large range of distances. The system is a useful alternative to other known distance measuring devices such as structured-light 3D scanners, time-of-flight cameras, Light Detection and Ranging (LIDAR) devices and structure from motion techniques. EBCA can be...
-
Flow boiling of R1233zd(E) in a 3 mm vertical tube at moderate and high reduced pressures
PublikacjaThe results of flow boiling of R1233zd(E) in a 3 mm vertical stainless steel tube are presented at moderate and high saturation temperatures. Integral flow characteristics in the form of pressure drop and heat transfer coefficient are discussed for saturation temperatures ranging from 115 to 145 °C (corresponding reduced pressures from 0.2 to 0.7), mass velocity of 800 kg/m2s and heat flux of 20 kW/m2. All of the obtained heat...
-
Society 4.0: Issues, Challenges, Approaches, and Enabling Technologies
PublikacjaThis guest edition of Cybernetics and Systems is a broadening continuation of our last year edition titled “Intelligence Augmentation and Amplification: Approaches, Tools, and Case Studies”. This time we cover research perspective extending towards what is known as Society 4.0. Bob de Vit brought the concept of Society 4.0 to life in his book “Society 4.0 – resolving eight key issues to build a citizens society”. From the Systems...
-
Characterization of GM3 Gangliosides in Human Milk throughout Lactation: Insights from the Analysis with the Use of Reversed-Phase Liquid Chromatography Coupled to Quadrupole Time-Of-Flight Mass Spectrometry
PublikacjaGangliosides are complex lipids found in human milk that play important structural and biological functions. In this study, we utilized reversed-phase liquid chromatography coupled to quadrupole time-of-flight mass spectrometry to evaluate the molecular distribution of GM3 in human milk samples collected at distinct lactation stages, ranging from colostrum to advanced lactation samples. Throughout lactation, GM3 d40:1 emerged as...
-
Three-dimensional characterization of porosity in iron ore pellets: A comprehensive study
PublikacjaThis paper presents a comprehensive study on the production and reduction of high-quality iron ore pellets characterized by a basicity index nearing 0.5 and diameters ranging from 1 to 2 cm. The reduction process was carried out in a hydrogen atmosphere at temperatures spanning 800–1000 ◦ C and a pressure of 8 bar. Initial f indings revealed substantial variations in pellet density and compressive strength, attributed to their...
-
Water and chemical properties of hydrometeors over central european mountains
PublikacjaAtmospheric pollutants are transferred to the groundby the contribution of various types of hydrometeors. Because ofthe different techniques of measurement, comparative analysesbetween them are often neglected. Hence, the main goal is tocompare water volume and chemistry of different types ofhydrometeors and their role in both: water balance and pollutantsdeposition. The results of water input and atmospheric depositschemistry...
-
Kinetic analysis of the reduction of a ternary system of Bi, Sb and Te oxides by hydrogen for BiSbTe3 synthesis
PublikacjaReduction in a hydrogen atmosphere of Bi2O3, Sb2O3 and TeO2 mixes oxides for the synthesis of BiSbTe3 was analysed. The reduction reactions of Sb2O3 and Sb2O4 oxides, as well as Bi2O3+Sb2O3 and Sb2O3+3TeO2 mix- tures, were also evaluated. The reduction of Sb2O4 is investigated for the first time. The reactions of the mixed oxides systems also were not the subject of research so far despite being used for synthesis of the (Bi,Sb)2Te3...
-
Freehand drawing versus digital design tools in architectural teaching
PublikacjaThe oldest drawings resembling modern architectural designs date from the 22nd Century BC. Throughout history, the first drawings have evolved into the basic tool of the architect’s work. The exchange of information between the architect and the contractor began to take place through a drawing system, allowing to describe three-dimensional space using flat representations. With time, architectural drawings also began to resemble...
-
Influence of Fluid Compressibility and Movements of the Swash Plate Axis of Rotation on the Volumetric Efficiency of Axial Piston Pumps
PublikacjaThis paper describes the design of a swash plate axial piston pump and the theoretical models describing the bulk modulus of aerated and non-aerated fluids. The dead space volume is defined and the influence of this volume and the fluid compressibility on the volumetric efficiency of the pump is considered. A displacement of the swash plate rotation axis is proposed to reduce the dead space volume for small swash plate swing angles....
-
Non-Least Square GNSS Positioning Algorithm for Densely Urbanized Areas
PublikacjaThe paper introduces an essentially new algorithm for calculating the GNSS position as an alternative to the least-square method. The proposed approach can be widely applied to any positioning method that uses multiple position lines for position calculation and is an example ofhow using a numerical solution can improve position accuracy without access to historical data. In essence, the method is based on the adaptation of the...
-
Correlation between Fractal Dimension and Areal Surface Parameters for Fracture Analysis after Bending-Torsion Fatigue
PublikacjaThis paper investigates the fracture surface topography of two steel and aluminum alloys subject to bending-torsion fatigue loadings, as well as their susceptibility to fatigue performance and failure mechanisms. Using fracture surface topography data analysis, elements with different geometries were elaborated. A correlation between the fractal dimension, other selected parameters of surface topography such as areal Sx, and...
-
Pursuing Analytically the Influence of Hearing Aid Use on Auditory Perception in Various Acoustic Situations
PublikacjaThe paper presents the development of a method for assessing auditory perception and the effectiveness of applying hearing aids for hard-of-hearing people during short-term (up to 7 days) and longer-term (up to 3 months) use. The method consists of a survey based on the APHAB questionnaire. Additional criteria such as the degree of hearing loss, technological level of hearing aids used, as well as the user experience are taken...
-
On the use of leading safety indicators in maritime and their feasibility for Maritime Autonomous Surface Ships
PublikacjaAlthough the safety of prospective Maritime Autonomous Surface Ships will largely depend on their ability to detect potential hazards and react to them, the contemporary scientific literature lacks the analysis of how to achieve this. This could be achieved through an application of leading safety indicators. The aim of the performed study was to identify the research directions of leading safety indicators in three safety-critical...
-
Multiple sound sources localization in free field using acoustic vector sensor
PublikacjaMethod and preliminary results of multiple sound sources localization in free field using the acoustic vector sensor were presented in this study. Direction of arrival (DOA) for considered source was determined based on sound intensity method supported by Fourier analysis. Obtained spectrum components for considered signal allowed to determine the DOA value for the particular frequency independently. The accuracy of the developed...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublikacjaThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Flow Process Models for Pipeline Diagnosis
PublikacjaThis chapter examines the problem of modeling and parameterization of the transmission pipeline flow process. First, the base model for discrete time is presented, which is a reference for other developed models. Then, the diagonal approximation (AMDA) method is proposed, in which the tridiagonal sub-matrices of the recombination matrix are approximated by their diagonal counterparts, which allows for a simple determination of...
-
Systems engineering approach to functional safety and cyber security of industrial critical installations
PublikacjaThis chapter addresses the systems engineering approach to integrated functional safety and cybersecurity analysis and management regarding selected references, standards and requirements concerning critical installations and their industrial automation and control system (IACS). The objective is to mitigate the vulnerability of industrial installations that include the information technology (IT) and the operational technology...
-
Systems engineering approach to functional safety and cyber security of industrial critical installations
PublikacjaThis chapter addresses the systems engineering approach to integrated functional safety and cybersecurity analysis and management regarding selected references, standards and requirements concerning critical installations and their industrial automation and control system (IACS). The objective is to mitigate the vulnerability of industrial installations that include the information technology (IT) and the operational technology...
-
Steady-State Vibration Level Measurement of the Five-Phase Induction Machine during Third Harmonic Injection or Open-Phase Faults
PublikacjaMultiphase electric machines are increasingly used in various industries and for electromobility. Complex systems have been developed for the control and powering of multiphase machines, which require verification. The quality of control and the power supply of electric machines is usually evaluated by analyzing various electrical parameters. On the other hand, taking into account the fact that a motor is an electrical-mechanical...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublikacjaThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
Elderly persons professional activity - substantive issues and methodical challenges
PublikacjaPopulation ageing and mass withdrawal of persons around retirement age from the labour market constitutes a serious threat for European Union economy, especially in the so-called new member states. The coming years are expected to bring a considerable increase in public spending on pensions and health care, as well as changes in the structure and size of consumer demand and an increase in the number of socially excluded individuals....
-
Building the Learning Environment for Sustainable Development: a Co-creation approach
PublikacjaEducation for sustainable development supports the improvement of knowledge, skills, attitudes and behaviors related to global challenges such as climate change, global warming and environmental degradation, among others. It is increasingly taking place through projects based on information and communication technologies. The effectiveness of the actions taken depends not only on the quality of the project activities or the...
-
Elementary analysis and energetic potential of the sludge from the Gdynia Dębogórze and Lębork wastewater treatment plants
PublikacjaThe paper aims to show the results of the elementary analysis of the sewage sludges from wastewater treatment plants in Gdynia Dębogórze and Lębork as well as measurements of the heat of combustion and the calculated calorific values according to regulation PN-93/Z-15008, taking into account water content and the composition of sewage sludge at different utilisation stages. The results presented in this paper are based on the analysis...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublikacjaBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Multimode systems of nonlinear equations: derivation, integrability, and numerical solutions
PublikacjaWe consider the propagation of electromagnetic pulses in isotropic media taking a third-order nonlinearityinto account. We develop a method for transforming Maxwell's equations based on a complete set ofprojection operators corresponding to wave-dispersion branches (in a waveguide or in matter) with thepropagation direction taken into account. The most important result of applying the method is a systemof equations describing the...
-
Identification of Bodner-Partom model parameters for technical fabrics
PublikacjaThe thorough analysis of modeling technical fabrics behavior with the viscoplastic Bodner-Partom constitutive law is presented. The study has been focused on differences between the warp and weft direction of the material. To obtain the model’s parameters only the uniaxial tensile laboratory tests with three different, but constant strain rates are required. The parameters have been found for polyester fibers PVC coated fabrics:...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Development of trolleybus public transport in Gdynia as part of sustainable mobility strategy
PublikacjaIn many EU cities trolleybuses are experiencing a period of revitalization. New lines, new and modern trolley-buses, the use of auxiliary propulsion battery, eco-logical values and others, create great opportunities for that kind of public transport as an effective tool to shape transport policy in accordance with the principles of sustainable mobility. Gdynia is one of three cities in Poland with trolleybuses public transport...
-
Blood Pressure Estimation Based on Blood Flow, ECG and Respiratory Signals Using Recurrent Neural Networks
PublikacjaThe estimation of systolic and diastolic blood pressure using artificial neural network is considered in the paper. The blood pressure values are estimated using pulse arrival time, and additionally RR intervals of ECG signal together with respiration signal. A single layer recurrent neural network with hyperbolic tangent activation function was used. The average blood pressure estimation error for the data obtained from 21 subjects...
-
THE CONCEPT OF MODELING OF SNOW IMPACT ON THE STRUCTURE OF THE SUSPENDED TAURON ARENA ROOF IN CRACOW
PublikacjaThe article presents studies and numerical simulations on modeling snow influence on TAURON ARENA suspended roof structure in Cracow. The scope of work includes experimental tests, functions solutions taking into account various cases of snow impact according to PN and EC, as well as numerical simulations for the sport and entertainment arena in the Czyzyny district. The FEM roof structure model developed in the SOFISITK software...
-
Call Control Evaluation in ASON/GMPLS Architecture
PublikacjaThe Automatically Switched Optical Network (ASON) utilizing Generalized Multi–Protocol Label Switching (GMPLS) protocols named as ASON/GMPLS is one of the propositions of Next Generation Network. The basic assumption of ASON control plane is a separation of call control from connection control. The control plane is divided into call control and connection control components. Presented work regards the problem of call control evaluation...
-
Method of determining the degree of liquid aeration in a variable capacity displacement pump
PublikacjaThe Author concludes, that there is a possibility of determining a concrete value of the liquid aeration coefficient during the pump operation by finding such value of coefficient with which the increase of torque of mechanical losses is proportional to the indicated torque determined with a fixed value of increase of pressure in the pump working chambers. The fixed value of increase of pressure assumed in searching the liquid...
-
An advanced Thermal-FSI approach to flow heating/cooling
PublikacjaActually, two-way thermal-energy exchange between working fluid and solid material of a casing is a leading problem for modern – semi automatic – design techniques. Many questions should be solved, especially, the turbulent mode of thermal energy transport both in fluid and solid, should be re-examined and reformulated from the primary principles. In the present paper, a group of researchers from Energy Conversion Department of...
-
Balancing energy processes in turbine engines
PublikacjaThe article discusses the issue of balancing energy processes in turbine engines in operation in aeronautic and PDULQHSURSXOVLRQV\VWHPVZLWKWKHDLPWRDQDO\VHDQGHYDOXDWH EDVLFRSHUDWLQJSDUDPHWHUV7KH¿UVWSDUWSUHVHQWV the problem of enormous amounts of energy needed for driving fans and compressors of the largest contemporary turbofan engines commonly used in long-distance aviation. The amounts of the transmitted power and the effect RIÀRZSDUDPHWHUVDQGFRQVWUXFWLRQDOSURSHUWLHVRIWKHHQJLQHV RQWKHLUSHUIRUPDQFHDQGUHDOHI¿FLHQF\DUH evaluated....
-
REVISING ENTREPRENEURIAL ORIENTATION (EO) IN SOCIAL ENTREPRENEURSHIP, QUALITATIVE EVIDENCE FROM WORK INTEGRATION SOCIAL ENTERPRISES (WISES) FROM POLAND
PublikacjaEntrepreneurial behaviour and entrepreneurial orientation (EO) of (commercial) entrepreneurship. have received significant scholarly attention in entrepreneurship and management research However, there are insufficient attempts discussing such behaviour and EO in non-profit, and particularly social entrepreneurship context, arguing that EO is higher in such contexts, or remains the same, some new EO dimensions are proposed, existing...
-
Electronic noses: Powerful tools in meat quality assessment
PublikacjaMain factors that are considered by consumers when choosing meat products are colour and aroma, of which the latter is a more reliable indicator of quality. However, a simple sensory evaluation of hedonistic qualities is often not sufficient to determine whether protein is past its shelf life, and consumption of spoiled meat can lead to serious health hazards. Some volatile compounds can be used as spoilage indicators, and so a...
-
Real-Time Gastrointestinal Tract Video Analysis on a Cluster Supercomputer
PublikacjaThe article presents a novel approach to medical video data analysis and recognition. Emphasis has been put on adapting existing algorithms detecting le- sions and bleedings for real time usage in a medical doctor's office during an en- doscopic examination. A system for diagnosis recommendation and disease detec- tion has been designed taking into account the limited mobility of the endoscope and the doctor's requirements. The...
-
Multiple sound sources localization in real time using acoustic vector sensor
PublikacjaMethod and preliminary results of multiple sound sources localization in real time using the acoustic vector sensor were presented in this study. Direction of arrival (DOA) for considered source was determined based on sound intensity method supported by Fourier analysis. Obtained spectrum components for considered signal allowed to determine the DOA value for the particular frequency independently. The accuracy of the developed...
-
The application of the Superpave method of climatic zones analysis in Poland with regard to bitumen performance grading
PublikacjaCurrently in Poland, similarly as in the other EU countries, road bitumens are tested and classified with regard to mainly the penetration value determined at the tempera-ture of 25C. It should be noted that this classification is not correlated with the cli-matic conditions in which the bitumens are to serve in the road pavement. Towards the end of the last century a new system of bitumen grading was developed and im-plemented...