Wyszukiwarka
Filtry
wszystkich: 3383
-
Katalog
- Publikacje 2617 wyników po odfiltrowaniu
- Czasopisma 39 wyników po odfiltrowaniu
- Osoby 59 wyników po odfiltrowaniu
- Wynalazki 8 wyników po odfiltrowaniu
- Projekty 10 wyników po odfiltrowaniu
- Laboratoria 1 wyników po odfiltrowaniu
- Zespoły Badawcze 1 wyników po odfiltrowaniu
- Aparatura Badawcza 3 wyników po odfiltrowaniu
- Kursy Online 41 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 602 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: LASERY PÓŁPRZEWODNIKOWE
-
Additive manufacturing of Proton-Conducting Ceramics by robocasting with integrated laser postprocessing
PublikacjaA hybrid system combining robocasting and NIR laser postprocessing has been designed to fabricate layers of mixed proton-electron conducting Ba0.5La0.5Co1-xFexO3-δ ceramic. The proposed manufacturing technique allows for the control of the geometry and microstructure and shortens the fabrication time to a range of a few minutes. Using 5 W laser power and a scanning speed of 500 mm⋅s− 1, sintering of a round-shaped layer with an...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublikacjaThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Laser patterned platform with PEDOT–graphene composite film for NO2 sensing
PublikacjaThis work presents a simple and fully electrochemical route used for fabricating of a NO2 gas sensor made of reduced-graphene-oxide-poly(3,4-ethylenedioxythiophene) composite film. The sensing platform was fabricated from alumina substrate and equipped with gold interdigitated electrodes and built-in heater.The temperature distribution on the surface of interdigitated electrodes was investigated by a thermalimaging camera and compared...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublikacjaMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
Optical and photoelectrochemical characterization of pulsed laser deposited Bi4V2O11, BICUVOX, and BIZNVOX
PublikacjaThin layers of three compounds from the BIMEVOX family (Bi4V2O11, Bi2V0.9Cu0.1O5.35, and Bi2V0.9Zn0.1O5.35) were prepared via pulsed laser deposition technique on quartz, silicon, and platinum foil and tested as photoanodes for water photooxidation. The film formation, as well as the crystallization upon heating, was characterized using X-ray diffraction and Raman spectroscopy. The optical properties were investigated using spectroscopic...
-
A new approach of coastal cliff monitoring using Mobile Laser Scanning
PublikacjaThe article proposes a new approach of coastal cliff monitoring which bases on a new comprehensive monitoring system, being a combination of mobile scanning from the sea with the geotechnical stability analysis. Mobile laser scanning is an innovative solution for 3D data collection which allows the monitored object geometry to be precisely measured, thus providing opportunities for series of analyses contributing to the development...
-
The effect of laser on metal surfaces for multidisciplinary usage in material and thermal engineering
PublikacjaThe subject of heat transfer and cooling systems is still a matter of contention in many different fields of science and industry. Infrigidation is much more difficult than warming, and so, much more needed in more and more different devices, starting from massive industrial machinery and air conditioning in commercial buildings, up to micro and nano-surgery tools. In fact, the size of many cooling systems is still a problem. It...
-
Odporność kawitacyjna stali 2H13 przetapianej wiązką lasera i stopowanej niobem
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali 2H13 po dwóch wariantach obróbki laserowej. W pierwszym wariancie powierzchnie stali przetapiano wiązką lasera CO2, a w drugim powierzchnie wzbogacano Nb w ilości 5% masowego.
-
Layer-by-layer polymer deposited fabrics with superior flame retardancy and electrical conductivity
PublikacjaSmart and multifunctional textiles and fabrics are progressively developing, such that multifunctional fabrics are becoming more widespread. We elaborated herein multi-layered flax fabrics with superior flame retardancy and conductivity, which revealed fireproof feature while keeping conductivity during burning. The flax fabric was reinforced by layer-by-layer (LbL) deposition of sodium polyacrylate (SPA), polyethylenimine (PEI),...
-
Półprzewodniki organiczne
PublikacjaW artykule przedstawiono zwięzły podział półprzewodników organicznych oraz opis zasadniczych właściwości i parametrów elektrycznych istotnych dla zastosowań elektronicznych. Omówiono koncepcje przewodnictwa elektrycznego i fotoprzewodnictwa półprzewodników organicznych.
-
Wpływ prędkości przesuwu wiązki lasera CO2 na odporność kawitacyjną stali 2H13
PublikacjaPrzedstawiono badania odporności kawitacyjnej stali 2H13 po przetapianiu jej powierzchni wiązką lasera CO2, przy różnych prędkościach obróbki laserowej. Stwierdzono wzrost odporności kawitacyjnej przy wzroście prędkości obróbki.
-
Drukowanie trwałych elementów z żywic utwardzanych światłem lasera w technologii SLA
PublikacjaŻywice stanowią ważny materiał służących do wytarzania określonych elementów technicznych w wielu obszarach współczesnego i nowoczesnego przemysłu. Niniejsze opracowanie poświęcono charakterystyce najstarszej z metod druku 3D na świecie – technologii stereolitografii. Omówiono zasadę działania i budowy modelu fizycznego, a także dokonano charakterystyki jej kluczowych czynników związanych z parametrami drukarki wraz z porównaniem...
-
The work of Professor Andrzej Lasota on asymptotic stability and recent progress
PublikacjaPraca poświęcona jest wkładowi Profesora Andrzeja Lasoty w teorię asymptotycznej stabilności iteracji operatorów stochastycznych na przestrzeni ostatnich 36 lat. Podkreślono aplikacyjny charakter wyników, pokazując stosowne przykłady z modelowania rozwoju komórki, optymalizacji wierceń geologicznych i ewolucji modeli kwantowych.
-
Fabrication Of Scaffolds From Ti6Al4V Powders Using The Computer Aided Laser Method
Publikacja -
Double wedge prism based beam deflector for precise laser beam steering
Publikacja -
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublikacjaLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Magnetic anisotropy in the exchange-biased laser-patterned thin Co/CoO films
Publikacja -
Surface Property Modification of Collagen, Hyaluronic Acid, and Chitosan Films with the Neodymium Laser
Publikacja -
The Erosion Resistance and Microstructure Evaluation of Laser Surface Alloyed Sintered Stainless Steels
Publikacja -
Surface texture formation in precision machining of direct laser deposited tungsten carbide
Publikacja -
Application of high pressure laser flash photolysis in studies on selected hemoprotein reactions
Publikacja -
Surface roughness analysis after machining of direct laser deposited tungsten carbide
Publikacja -
Influence of laser remelting at cryogenic conditions on corrosion resistance of non-ferrous alloys
PublikacjaCelem nadtapiania laserowego elementów wytwarzanych z stopów aluminium, miedzi i tytanu jest uzyskanie wysokiej twadrości i odporności na korozję dla wydłużenia okresu ich eksploatacji w rezultacie ich szybkiej krystalizacji. Końcowa mikrostruktura, skład fazowy i właściwości wymienionych stopów zależą od parametrów obróbki laserowej oraz budowy wykresów równowagi fazowej. W artykule przedstawiono wpływ laserowego nadtapiania...
-
Development of free electron laser and accelerator technology in Poland (CARE and EuCARD projects)
Publikacja -
Acousto-optic interaction of a Gaussian laser beam with an ultrasonic wave of cylindrical symmetry
Publikacja -
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublikacjaThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
APPLYING RANSAC ALGORITHM FOR FITTING SCANNING STRIPS FROM AIRBORNE LASER SCANNING
PublikacjaDuring the development of the data acquired by airborne laser scanning the important issue is the fitting and georeferencing of ALS point clouds by means of the tie surfaces and the reference planes. The process of scanning strips adjustment is based on mutual integration of point clouds (scanning strips) and their adaptation to the reference planes.In simultaneous adjustment all strips are combined into one geometrically coherent...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublikacjaThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Preparation of platinum modified titanium dioxide nanoparticles with the use of laser ablation in water
PublikacjaWe report on the preparation method of nanocrystalline titanium dioxide modified with platinum by using nanosecond laser ablation in liquid (LAL). Titania in the form of anatase crystals has been prepared in a two-stage process. Initially, irradiation by laser beam of a titanium metal plate fixed in a glass container filled with deionized water was conducted. After that, the ablation process was continued, with the use of a platinum...
-
Chemical, thermal and laser processes in recycling of photovoltaic silicon solar cells and modules
PublikacjaIn recent years, photovoltaic power generation systems have been gaining unprecedented attention as an environmentally beneficial method to solve the energy problem. From the economic point of view the pure silicon, which can be recapture from the used cells, is the most important material due to its cost and shortage. In the paper selected methods of used or damaged module and cells recycling and experimental results are presented....
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublikacjaThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublikacjaAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublikacjaDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Mechanical and Corrosion Properties of Laser Surface-Treated Ti13Nb13Zr Alloy with MWCNTs Coatings
Publikacja: Titanium and its alloys is the main group of materials used in prosthetics and implantology. Despite their popularity and many advantages associated with their biocompatibility, these materials have a few significant disadvantages. These include low biologic activity—which reduces the growth of fibrous tissue and allows loosening of the prosthesis—the possibility of metallosis and related inflammation or other allergic reactions,...
-
Stability Assessment of Coastal Cliffs Incorporating Laser Scanning Technology and a Numerical Analysis
PublikacjaWe investigated the cli coast in Jastrzebia Gora, Poland. The measurements that were taken between 2014 and 2018 by applying terrestrial, mobile, and airborne laser scanning describe a huge geometric modification involving dislocations in a 2.5 m range. Dierential maps and a volumetric change analysis made it possible to identify the most deformed cli’s location. Part of the monitoring of coastal change involved the measurement...
-
Formation of the hollow nanopillar arrays through the laser-induced transformation of TiO2 nanotubes
PublikacjaIn the following article, we present a simple, two-step method of creating spaced, hollow nanopillars, from the titania nanotube arrays via pulsed laser-treatment. Due to the high ordering of the structure, the prepared material exhibits photonic properties, which has been shown to increase the overall photoefficiency. The optical and morphological changes in the titania nanotubes after pulsed laser-treatment with 532, 355, and...
-
Scalable Route toward Superior Photoresponse of UV-Laser-Treated TiO2 Nanotubes
PublikacjaTitanium dioxide nanotubes gain considerable attention as a photoactive material due to chemical stability, photocorrosion resistance, or lowcost manufacturing method. This work presents scalable pulsed laser modification of TiO2 nanotubes resulting in enhanced photoactivity in a system equipped with a motorized table, which allows for modifications of both precisely selected and any-large sample area. Images obtained from scanning...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublikacjaLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublikacjaLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublikacjaComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Application of the laser diode with central wavelength 975 nm for the therapy of neurofibroma and hemangiomas
PublikacjaThis paper presents newly developed dermatological laser (with central wavelength 975 nm) for application in therapies requiring deep penetration of tissue, e.g. cutaneous (dermal) neurofibroma (Recklinghausen disease) and hemangiomas. This laser can work either in pulse or continues wave mode. Laser radiation is transmitted toward the application region by optical fiber with a diameter of 0.6 mm. The compact design of the laser...
-
Combined Close Range Photogrammetry and Terrestrial Laser Scanning for Ship Hull Modelling
PublikacjaThe paper addresses the fields of combined close-range photogrammetry and terrestrial laser scanning in the light of ship modelling. The authors pointed out precision and measurement accuracy due to their possible complex application for ship hulls inventories. Due to prescribed vitality of every ship structure, it is crucial to prepare documentation to support the vessel processes. The presented methods are directed, combined...
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublikacjaLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Laser induced elastooptics in novel Bi2O3, and Pr2O3 doped tellurite rich glasses
Publikacja -
Laser Investigations of Flow Patterns in Electrostatic Precipitators and Non Thermal Plasma Reactors
Publikacja -
Influence of laser beam machining on the cavitation resistance of Fe-Cr-Co clad.
PublikacjaW pracy przedstawiono wpływ laserowego nagrzewania bezzmiany stanu skupienia i laserowego przetapiania napoin ze stopu Fe-Cr-Co na ich odporność kawitacyjną. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Plastyczne odkształcenia powierzchni określano za pomocą analizy obrazów erodowanych powierzchni. Uzyskane rezultaty wskazują, że laserowo obrabiane powierzchnie miały różną podatność do plastycznego odkształcania...
-
Colorimetric study of the post-processing effect due to pulsed laser cleaning of paper.
PublikacjaW artykule przedstawiono wyniki badań procesu oczyszczania papieru implulsami laserowymi o różnej długości fali. Oceny dokonywano na podstawie pomierzonych wartości parametrów kolorymetrycznych. Badania obejmowały próbki papieru o różnym wieku.
-
Cavitation erosion of some laser-produced iron-base corrosion-resistance alloys
PublikacjaW pracy przedstawiono badania kawitacyjne stali C45, X20Cr13 oraz X5CrNi18-10 po laserowym stopowaniu ich warstwy wierzchniej proszkami Mn, Cr, Ni, Si, Ti, Co, Al, Mo, B. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Zniszczenia powierzchni w okresie inkubacji oceniano metodą optyczną. Przedstawiono związek pomiędzy uzyskaną mikrostrukturą obrabianej warstwy i jej odpornością kawitacyjną.
-
Relationship between microstructure of laser alloyed C45 steel and its cavitation resistance.
PublikacjaW pracy przedstawiono badania wpływu laserowo kształtowanej mikrostruktury na stali C45 po stopowniu różnymi kompozycjami proszków metali na własności kawitacyjne warstwy wierzchniej. Badania prowadzono w początkowym stadium erozji kawitacyjnej. Stwierdzono, że lepszą odporność kawitacyjną osiąga się gdy mikrostruktura jest podatna do umacniania odkształceniowego np. w obecności pewnej ilości austenitu w strukturze.