Filtry
wszystkich: 2464
-
Katalog
- Publikacje 660 wyników po odfiltrowaniu
- Czasopisma 2 wyników po odfiltrowaniu
- Osoby 4 wyników po odfiltrowaniu
- Wynalazki 1 wyników po odfiltrowaniu
- Laboratoria 3 wyników po odfiltrowaniu
- Aparatura Badawcza 2 wyników po odfiltrowaniu
- Kursy Online 1 wyników po odfiltrowaniu
- Wydarzenia 2 wyników po odfiltrowaniu
- Dane Badawcze 1789 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: QM/MM
-
Experimental analysis of chip removing system in circular sawing machine
PublikacjaPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
Badania porównawcze wpływu grubości ścianki powłoki o przekroju niekołowym, wykonanej z tworzywa GRP, w obiekcie gruntowo-powłokowym
PublikacjaW artykule przedstawiono badania porównawcze przepustów wykonanych z tworzywa GRP (Glass Reinforcement Poliester) zabudowanych w warunkach naturalnych i obciążanych układem sił symulujących obciążenia komunikacyjne zgodne z „Modelem Obciążenia 1” wg [7]. Analizowano dwie konstrukcje o identycznym przekroju poprzecznym (profil dzwonowy DN3000/2400), ale różnej grubości ścianki: standardowej 45 mm i zredukowanej 35 mm. Badania obejmowały...
-
CARDIOVASCULAR RISK FACTORS AMONG POLISH EMPLOYEES OF UNIFORMED SERVICES
PublikacjaObjectives: Employees of uniformed services (EoUS) were screened for cardiovascular risk factors. Material and Methods: A total of 1138 EoUS (age M±SD 49.9±6.0 years) and 263 controls (age M±SD 54.4±9.7 years) under the care of the cardiology clinic in Gdańsk, Poland,were included in the study. Medical history and blood samples were collected, and a physical examination was performed. Ten-year cardiovascular risk of death was...
-
Sposób zbrojenia wymuszonego docieraków tarczowych
PublikacjaW artykule przedstawiono konstrukcję głowicy do mechanicznego zbrojenia płaskiej tarczy docierającej o średnicy 580 mm mikroziarnami ściernymi. Opracowano model przyrządu w programie SolidWorks 2007 oraz przeprowadzono obliczenia konstrukcji nośnej urządzenia.
-
EFEKTYWNOŚĆ STOSOWANIA ZDERZAKÓW STYROPIANOWYCH POMIĘDZY ZDERZAJĄCYMI SIĘ KONSTRUKCJAMI STALOWYMI
PublikacjaPodczas wstrząsów sejsmicznych o różnym natężeniu, wielokrotnie obserwowano zjawisko zde-rzania się konstrukcji ze sobą sąsiadujących, co mogło prowadzić nawet do jej całkowitego zniszczenia. Na podstawie obserwacji, badań numeryczny i eksperymentalnych stwierdzono, że przyczyną kolizji jest niedostateczna przerwa pomiędzy konstrukcjami. Ponadto czynnikami, które również mogą doprowadzić do zderzeń są różnice w masach lub sztywnościach...
-
Electromagnetic wave scattering from material objects using hybrid methods
PublikacjaRozdział zawiera opis hybrydowych metod analizy stanowiących połączenie metody różnic skończonych w dziedzinie częstotliwości (FDFD) z metodą dopasowania rodzajów (MM), służących do badania cylindrycznych struktur falowych w układach zamkniętych i otwartych.
-
Narzędzia dla docierarek jednotarczowych - modułowe konstrukcje i ich analiza.
PublikacjaPrzedstawiono konstrukcję ścierno-metalowych narzędzi o średnicy 380 mm do obróbki powierzchni płaskich. Omówiono szczegółowo ich modułową budowę i poddano analizie projektowej technologiczność konstrukcji. W ocenie stosowano kryteria konstrukcyjne i użytkowe
-
The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints
PublikacjaThe purpose of the following study was to compare the effect of the shape of a tool onthe joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the bestpossible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To theauthors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Fivebutt joints were made with a self-developed, cylindrical,...
-
FLUID BED COATING OF MINITABLETS AND PELLETS WITH OPTIMIZATION OF THE PROCESS BASED ON TAGUCHI METHOD
PublikacjaSmall particles like pellets are coated in fluid bed systems. This method can be also feasible for minitablets but the selection of optimal process parameters is complicated. The aim of the research was to optimize the coating process for minitablets and to compare the conditions required for pellets. Minimum fluidization velocities (umf) for 2.0 and 2.5 mm minitablets and 0.7-0.8 mm or 1.0-1.25 mm pellets were determined experimentally....
-
A Highly Sensitive Planar Microwave Sensor for Detecting Direction and Angle of Rotation
PublikacjaThis article presents a technique based on a modified complementary split-ring resonator (CSRR) to detect angular displacement and direction of rotation with high resolution and sensitivity over a wide dynamic range. The proposed microwave planar sensor takes advantage of the asymmetry of the sensor geometry and measures the angle of rotation in terms of the change in the relative phase of the reflection coefficients. The sensor...
-
Wpływ warunków hydraulicznych w sieci wodociągowej na wtórne zanieczyszczenie wody = Effect of hydraulic conditions in the water distribution system on the secondary water pollution
PublikacjaCelem badań jest próba empirycznego wykazania wpływu zmian prędkości i czasu przebywania wody w przewymiarowanej sieci wodociągowej na wtórne jej zanieczyszczenie. Podstawą analizy są pomiary hydrauliczne wykonane podczas realizacji płukania rurociągów żeliwnych D=100 mm oraz badania laboratoryjne popłuczyn w zakresie suchej pozostałości, w tym zawartości związków żelaza. Każdą pobraną próbkę popłuczyn z hydrantów poddano szczegółowej...
-
New Complementary Resonator for Permittivity- and Thickness-Based Dielectric Characterization
PublikacjaThe design of high-performance complementary meta-resonators for microwave sensors featur-ing high sensitivity and consistent evaluation of dielectric materials is challenging. This paper presents the design and implementation of a novel complementary resonator with high sensi-tivity for dielectric substrate characterization based on permittivity and thickness. A comple-mentary crossed arrow resonator (CCAR) is proposed and integrated...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublikacjaThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Circularly Polarized Antenna Array design with the Potential of Gain-Size Trade-off and Omnidirectional Radiation for Millimeter-Wave Small Base Station Applications
PublikacjaThis paper presents the design and validation of a slot-patch-hybrid circularly polarized antenna array for 28 GHz millimeter (mm) wave (mm-wave) applications. The proposed design has a simple geometry that facilitates the fabrication process, which is otherwise a challenging task due to the sub-mm dimensions of the circuit in the mm-wave band. In the proposed structure, aperture-coupled series slot-fed array is utilized to excite...
-
Topologie der Strömung und das Geschwindigkeitsfeld während des Blasenaufstiegs und der Koaleszenz
PublikacjaPrzedstawiono wyniki pomiarów prędkości wokól wzrastających i łączących się pęhcerzyków powietrza generowanych z dwóch igieł oddalonyhc od siebie o 5 i 10 mm. W badaniach uzyto układ PIV oraz kamerę do szybkich zdjęć.
-
Comprehensive dimension scaling of multi-band antennas for operating frequencies and substrate parameters
PublikacjaIn this paper, low-cost and comprehensive redesign of multi-band antennas with respect to the operating frequencies and material parameters of the substrate is presented. Our approach exploits an inverse surrogate model identified based on a set of reference designs optimized at the level of coarse-discretization EM simulations of the antenna at hand. An iterative correction procedure is also implemented to account for the initial...
-
Numerical analysis of chip removing system operation in circular sawing machine using CFD software
PublikacjaPaper presents the analysis of the results of numerical simulations of the air flow process of wood chips removing system in the circular sawing machine. The attention is focused on the upper cover and bottom shelter of the chip removing system. Within the framework of the work a systematic numerical modeling of the air flow distribution in the cover and shelter during operation of the selected rotational speed of saw blade with...
-
Compact 4 × 4 butler matrix with non‐standard phase differences for IoT applications
PublikacjaButler matrices represent a popular class of feeding networks for antenna arrays. Large dimensions and the lack of flexibility in terms of achievable output phase difference make conventional Butler structures of limited use for modern communication devices. In this work, a compact planar 4 × 4 matrix with non-standard relative phase shifts of –30º, 150º, –120º, and 60º has been proposed. The structure is designed to operate at...
-
The sensitivity of bacteria to heavy metals in presence of mineral ship motor oil in coastal marine sediments and waters.
PublikacjaThe sensitivity of bacteria, isolated from coastal marine sediments and waters of Sopot beach, Gdańsk Bay (Poland), to heavy metals in the presence of mineral ship motor oil were studied. All isolated heterotrophic bacteria were resistant to the 0.1 mM lead concentration occurring in the environment. Metal resistance of bacteria isolated from coastal water was strongly related to mineral ship motor oil concentration. At 0.1% mineral...
-
Wymiana ciepła podczas wrzenia w przepływie przy zastosowaniu wkładek blokujących
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych wrzenia w przepływie w minikanałach. Jako czynnik roboczy zastosowano Freon R123. Przebadano pojedyncze, pionowe rurki srebrne o długości 380 mm i szerokości 2.3 mm przy zastosowaniu dwóch wariantów wkładek turbulizujących przepływ. Przeanalizowano wpływ strumienia masy i gęstości strumienia ciepła na współczynnik przejmowania ciepła. Wyniki porównane zostały z popularnymi korelacjami...
-
Computational methods for calculation of binding free energy for ligand-receptor complexes
PublikacjaAccurate description of the molecular complexes energetic influence is required for understanding of many biological functions carried out by proteins. Therefore, estimation of binding free energy for ligand-receptor complexes is of highest importance for structure-based ligand design and drug discovery approaches.Experimental methods of determination of difference in Gibbs'es free energy have many limitations. Thus, computational...
-
Beta-galactosidase activity of Meiothermus ruber cells
PublikacjaFreeze-dried cells of Meiothermus ruber catalyses cleavage of o-nitrophenyl-b-D-galactopiranoside (oNPb-gal) and conversion of lactose into glucose and galactose. The permeabilization with 2%toluene,20%ethanol and 20%acetone increased enzymatic activity from 74.87 U/g of lyophilized cells up to 129.44,114.38 and 90.19 U/g,respectively. Ethanol was an effective permeabilizing agent and its efficiency was dependent on the concentration,...
-
Zanieczyszczenia powietrza w środowisku pracy podczas przecinania ściernicowego ręcznego i możliwości ich ograniczenia
PublikacjaW artykule przedstawiono zagrożenie środowiska zanieczyszczeniami powietrza pyłami i gazami w pomiesz-czeniu zamkniętym podczas przecinania ręcznego prętów stalowych ściernicami elektrokorundowymi. Ocenę porównawczą zanieczyszczeń powietrza wewnętrznego, z użyciem ściernic o średnicy 230 mm pięciu producen-tów, dokonano na podstawie 30. przecięć każdą ściernicą pręta stalowego o średnicy 20 mm. W zależności od producenta ściernicy...
-
Measurements of fundamental properties of homogeneous tissue phantoms
PublikacjaWe present the optical measurement techniques used in human skin phantom studies. Their accuracy and the sources of errors in microscopic parameters’ estimation of the produced phantoms are described. We have produced optical phantoms for the purpose of simulating human skin tissue at the wavelength of 930 nm. Optical coherence tomography was used to measure the thickness and surface roughness and to detect the internal inhomogeneities....
-
The use of thin diamond films in fiber optic low-coherence interferometers”
PublikacjaIn this paper we present the use of thin diamond films in fiber-optic low-coherence interferometers. Two kinds of diamond surfaces were used: undoped diamond film and boron-doped diamond film. They were deposited on glass plates as well as silicon layers. A conventionally used mirror was used as a reference layer. Diamond films were deposited using Microwave Plasma Enhanced Chemical Vapour Deposition (μPE CVD) system. Measurements...
-
Novel structure and design of compact UWB slot antenna
PublikacjaIn this paper, a novel structure of a compact UWB slot antenna is presented along with a simulation-driven design optimization algorithm for adjusting geometry parameters of the device. Our primary objective is to obtain small footprint of the structure while maintaining its acceptable electrical performance. It is achieved by introducing sufficiently large number of geometry degrees of freedom, including increased number of parameterized...
-
Symulacja rozmieszczenia wkładek ściernych w narzędziu tarczowym do mikroszlifowania
PublikacjaPrzedstawiono wyniki analiz symulacyjnych rozmieszczenia tabletek ściernych w narzędziu do obróbki powierzchni płaskich na docierarce jednotarczowej. W analizowanym narzędziu ścierno-metalowym uwzględniono zróżnicowany stan zużycia tarczy. Stosowano kołowe wkładki ścierne o średnicy 23 mm.
-
Analiza rozmieszczenia wkładek ściernych w docieraku składanym
PublikacjaPrzedstawiono wyniki analiz symulacyjnych rozmieszczenia wkładek ściernych w narzędziu do obróbki powierzchni płaskich na docierarce jednotarczowej. W analizowanym narzędziu ścierno-metalowym uwzględniono zróżnicowany stan zużycia tarczy. Stosowano kołowe wkładki ścierne o średnicy 23 mm.
-
Fundamenty budynku mieszkalno-usługowego ''Transatlantyk'' w Gdyni
PublikacjaBudynek ma 13 kondygnacji i kubaturę 57000 m3. Obudowę wykopu głębokości ponad 7 m pod częścią podziemną budynku ( o powierzchni 2500 m2) stanowiły ściany szczelinowe grubości 60 cm, rozparte rurami stalowymi śrdnicy 508 mm.
-
Pomiary temperatury podczas gładzenia otworów
PublikacjaPrzedstawiono wyniki badań temperatury podczas gładzenia otworów w elementach stalowych. Analizowano obróbkę otworów o średnicach 75H7, 75H10 i 150H7 mm. W badaniach zastosowano metodę termowizyjną. Otrzymane wyniki pomiarów pozwolą właściwie zaplanować miejsce i czas kontroli.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych kondensacji czynnika HFE-7100 w minikanale o średnicy wewnętrznej 2.3 mm. Opisano również oryginalne podejście w prowadzeniu badań nad uzyskaniem lokalnych wartości współczynnika przejmowania ciepła podczas kondensacji w przepływie.
-
Wettability of Horizontal Stainless Steel Tube by Nanofluid Droplets
PublikacjaThe goal of the present work was the experimental determination of the contact angle of three nanofluids, i.e. water-Al2O3, water-Cu and water-TiO2 on horizontal stainless steel tube of 1.6 mm OD. Of particular interest was the effect of nanoparticle concentration (0.01%, 0.1%, and 1% by weight) on droplet contact angle.
-
Technologia nagniatania stali hartowanych.
PublikacjaPrzedstawiono wyniki badań nagniatania wałków ze stali 45 o twardości 23-56 HRC. Do nagniatania zastosowano tokarkę CNC oraz specjalne narzędzie z kulką ceramiczną fi6 mm. Badano wpływ parametrów technologicznych obróbki nagniataniem na chropowatość powierzchni.
-
Ekspertyza połączeń lutowanych rur miedzianych
PublikacjaCelem pracy było ustalenie rodzaju lutu zastosowanego do spajania rur miedzianych o średnicy 20 mm, ustalenie technologii lutowania oraz wydanie opinii czy połączenia lutowane gwarantują bezpieczeństwo podczas użytkowania rurociągu w wewnętrznej instalacji gazowej w budownictwie mieszkaniowym
-
Modeling organic nitrogen conversions in activated sludge bioreactors
PublikacjaFor biological nutrient removal (BNR) systems designed to maximize nitrogen removal, the effluent total nitrogen (TN) concentration may range from 2.0 to 4.0 g N/m3 with about 25-50% in the form of organic nitrogen (ON). In this study, current approaches to modeling organic N conversions (separate processes vs. constant contents of organic fractions) were compared. A new conceptual model of ON conversions was developed and combined...
-
Morphometric evaluation of the delayed cerebral arteries response to acetazolamide test in patients with chronic carotid artery stenosis using computed tomography angiography
PublikacjaBackground: The evidence accumulates that the response to acetazolamide test is delayed on the ipsilateral side to stenosis. However, the effect of acetazolamide beyond 30 minutes after acetazolamide administration remains unknown. The aim of this study was to assess the diameters of: anterior cerebral arteries (ACAs), middle cerebral arteries (MCAs) and posterior cerebral arteries (PCAs) before and 60 minutes after the acetazolamide...
-
Wpływ parametrów technologicznych nagniatania tocznego na chropowatość powierzchni części klasy wałek
PublikacjaW artykule zamieszczono wyniki badań wpływu nagniatania tocznego na chropowatość powierzchni wałków ze stali C45. Badania przeprowadzono na serii próbek o średnicy 56 mm na tokarce CNC z użyciem nagniataka z tensometrycznym pomiarem siły nagniatanej podczas obróbki.
-
Sliding burnishing technology of holes in hardened steel
PublikacjaNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Nagniatanie stali o różnej twardości narzędziami ceramicznymi.
PublikacjaPrzedstawiono wyniki badań nagniatania wałków ze stali 45 o twardości w zakresie 23-56 HRC. Do nagniatania zastosowano tokarkę CNC oraz specjalne narzędzie z kulką ceramiczną fi6 mm. Badano wpływ parametrów technologicznych obróbki nagniataniem na chropowatość powierzchni.
-
60 GHz Microstrip Van Atta Arrays for Millimeter Wave Identification and Localization
PublikacjaIn this paper performance comparison of co-polarized and cross-polarized microstrip Van Atta arrays working in the 60 GHz frequency range is presented. They can be treated as simple chipless RFID tags with frequency response based identification. Tags with three different nominal resonance frequencies of 57, 62 and 67 GHz are designed by scaling optimized base model. Designed 62 GHz co-polarized and cross-polarized arrays with...
-
Thermal-FSI modeling of flow and heat transfer in a heat exchangerbased on minichanels
PublikacjaIn this paper selected numerical modelling problems for an advanced thermal-FSI ("Fluid Solid Interaction") mini-channel heat exchanger model are presented. Special attention is given to the heat transfer between the separated mediums for different mass flows. Similar modelling problems have also been discussed in the literature dedicated to numerical and theoretical modelling problems for typical heat exchangers [1, 2, 3]. Basic...
-
Experimental examination and modification of chip suction system in circular sawing machine
PublikacjaThe article presents the results of experimental examination of the wood chip suction system in the existing sliding table saw before and after its modifi cation. The studies focused on the extraction hood of the mentioned system. The methodical experimental research of the pressure distribution inside the hood during wood chip removal for the selected rotational speed of saw blades of 3500 and 6000 min-1 with a diameter of 300...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublikacjaA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
Monitorowanie szybkości korozji stali w Martwej Wiśle metodą syntezy harmonicznej
PublikacjaPrzedstawiono wybrane wyniki badań polowych nad przydatnością praktyczną opracowanej niedawno metody syntezy harmonicznej (SH) do monitorowania szybkości korozji metali. Badania dotyczyły stali węglowej korodującej w środowisku słonawym wody Martwej Wisły. Korozję stali monitorowano przez okres ok. 20 dni w odstępach dwudniowych za pomocą umieszczonych w wodzie sond trójelektrodowych korzystając z przenośnej aparatury Solartron...
-
Hydraulic conductivity of a biopolymer treated sand
PublikacjaThis paper presents results of laboratory assessment of creating seepage barriers in a sandy soil using biopolymer additives (bio substance), which consist of polysaccharides and water. Polysaccharides strongly interact with water to produce a viscous suspension. The aim of the conducted work was to investigate the influence of a biosubstance employed in a highly permeable sandy soil. The amount of the biopolymer used in a sample...
-
Determination of Moisture Content Profiles of Spruce Wood After High Temperature Process and Air Drying
PublikacjaThe results of moisture content of wood after the process of its drying under high temperature conditions and air drying are presented. Wood samples, namely spruce (Picea abies Karst.) from the northern part of Pomerania region in Poland, were subject of steam and air drying.The aim of experiments was to measure moisture content of wood in its cross sections using moisture meter WRD-100. The samples of thickness 70 mm and length...
-
A Regional ITRF Densification by Blending Permanent and Campaign Data — The CEGRN campaigns and the Central European Velocity Field
PublikacjaThe CERGOP Project of the Central European Countries initiated six GPS observation campaigns from 1994 to 2001. By the high standards set within this project for site selection, observation and analysis a consistent set of epoch solutions with a precision in the 3–5 mm range was created. The network contains about 19 permanent and 38 epoch stations. In this paper a first combination solution over the seven years with a velocity...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublikacjaIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Pool boiling of water-Al2O3 and water-Cu nanofluids on horizontal smooth tubes
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia dwóch nanocieczy, tj. woda-Al2O3 i woda-Cu o trzech koncentracjach masowych nanocząstek: 0.01%,0.1% oraz 1% na poziomych gładkich rurkach ze stali nierdzewnej i miedzi o średnicy zewnętrznej 10 mm.