Filtry
wszystkich: 1236
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: phraseological units
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 20MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
DLC coating doped with W in ring-on-ring sliding with water lubrication 10MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: WATER. Tribometer: PT-3. Overall test time >15h. The test was...
-
Adiabatic potential energy curves of the 3, 4 and 5^1Σ^+ excited states of LiCs molecule
Dane BadawczeAdiabatic potential energy curves of the 3, 4, and 5^1Σ^+ excited states have been calculated for the LiCs molecule. The results of three excited states of the symmetry Σ^+ have been obtained by the nonrelativistic multireference configuration interaction (MRCI) method used with pseudopotentials describing the interaction of valence electrons with atomic...
-
The Application of a Mobile Unmanned Device for Monitoring Water and Sediment Pollution in the Port of Gdynia
PublikacjaPollution in the Port of Gdynia can encompass various types of substances and contaminants that affect the quality of water and sediment in this region. Ships entering and leaving the port can release pollutants such as oil, fuel, waste, and chemicals into the water. Controlling and monitoring these pollutants is a crucial part of environmental stewardship. In recent years, uncrewed units have been increasingly in use for in situ...
-
Experimental database of 3D lattice structure scaffolds testing
Dane BadawczeDataset contains results of validation (experimental testing) of 3D lattice scaffolds proposed in the paper "Mathematical approach to design 3D scaffolds for the 3D printable bone implant". There are presented three series of experimental testing for each of seven tested scaffolds:
-
Hybrid use of the building as a method supporting epidemic safety
PublikacjaThe COVID-19 pandemic has resulted in changing organisational and technical requirements in the operation of treatment facilities. This paper summarises the available knowledge on the principles of hybrid design of the architecture of treatment units to ensure that different levels of sanitary and hygienic safeguards can be implemented. The basis of this narrative overview is an analysis of the existing Polish legislation on required...
-
Extraction of information from born-digital PDF documents for reproducible research
PublikacjaBorn-digital PDF electronic documents might reasonably be expected to preserve useful data units of their source originals that suffice to produce executable papers for reproducible research. Unfortunately, developers of authoring tools may adopt arbitrary PDF generation strategies, producing a plethora of internal data representations. Such common information units as text paragraphs, tables, function graphs and flow diagrams,...
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 20MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 20MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
DLC coating doped with W in ring-on-ring sliding with saline solution (0.9% wt.) lubrication 10MPa/0.1m/s
Dane BadawczeWear tests in sliding friction of 1% W (tungsten) doped DLC coating on 1.4021 (EN 10088-1) heat treated stainless steel. Ring - on - ring contact in unidirectional sliding, DLC-W over DLC-W. Mean contact stress: 10MPa. Sliding velocity: 0,1 m/s. Mean friction radius: 9.5mm. Lubricant: SALINE SOLUTION (0.9% wt.). Tribometer: PT-3. Overall test time >15h....
-
Zadłużenie jednostek samorządu terytorialnego i jego determinanty
PublikacjaW artykule zbadano przesłanki i skutki zadłużania się jednostek samorządu terytorialnego w Polsce, a także zidentyfikowano determinanty ich zadłużenia w podziale na prawno-finansowe, polityczne, ekonomiczno-społeczne i organizacyjno-zarządcze. Przedstawiono również poziom zadłużenia tych jednostek w latach 2003-2020. Najbardziej zadłużone są miasta na prawach powiatu i gminy, co jest przede wszystkim związane z realizowanymi przez...
-
Classification of Landscape Physiognomies in Rural Poland: The Case of the Municipality of Cekcyn
PublikacjaThis article presents a methodology and the results of the classification of the rural landscapes physiognomies conducted on the study area located in the municipality of Cekcyn, Poland. The study aimed to develop a landscape identification method that would combine natural, cultural, and visual criteria with which to implement the provisions of the European Landscape Convention. The realization of the European Landscape Convention...
-
Post processing and selecting data obtain with parametric sub-bottom profiler SES-2000 Standard during sounding the Gulf of Gdansk
PublikacjaThe main goal of the paper is to describe the results of sounding the Gulf of Gdansk seabed using a parametric sub-bottom profiler SES-2000 Standard. Quality of obtained during trials data depends inter alia on proper location of antenna to reduce influence of pitch, roll, heave and ship noise (bubbles from propeller and a hull flow, vibration from main engine and peripheral devices). Furthermore calibration of complementary units...
-
Algorithms and Tools for Intelligent Control of Critical Infrastructure Systems
PublikacjaCritical Infrastructure Systems (CIS) are spatially distributed and of a network structure. The dynamics are nonlinear, uncertain and with several time scales. There is a variety of different objectives to be reliably met under a wide range of operational conditions. The operational conditions are influenced by the disturbance inputs, operating ranges of the CIS, faults in the sensors and actuators and abnormalities occurring in...
-
A GPU Solver for Sparse Generalized Eigenvalue Problems with Symmetric Complex-Valued Matrices Obtained Using Higher-Order FEM
PublikacjaThe paper discusses a fast implementation of the stabilized locally optimal block preconditioned conjugate gradient (sLOBPCG) method, using a hierarchical multilevel preconditioner to solve nonHermitian sparse generalized eigenvalue problems with large symmetric complex-valued matrices obtained using the higher-order finite-element method (FEM), applied to the analysis of a microwave resonator. The resonant frequencies of the low-order...
-
Visual Traffic Noise Monitoring in Urban Areas
PublikacjaThe paper presents an advanced system for railway and road traffic noise monitoring in metropolitan areas. This system is a functional part of a more complex solution designed for environmental monitoring in cities utilizing analyses of sound, vision and air pollution, based on a ubiquitous computing approach. The system consists of many autonomous, universal measuring units and a multimedia server, which gathers, processes and...
-
Active management of equipment cooling in hoteling data centers
PublikacjaHoteling data centers are designated for housing computing and storage units of many, usually small customers, as opposed to traditional data centers supporting own computing and storage resources of a bigger company. One of the services to be provided to consumer’s equipment is cooling. Cooling in data centers is prevalently achieved by circulating air in computer room. Efficient cooling requires delivering cold air from central...
-
Quality of Cryptocurrency Mining on Previous Generation NVIDIA GTX GPUs
PublikacjaCurrently, there is a lot of previous generation NVIDIA GTX graphical processing units (GPUs) available on the market, which were ousted from by next-gen RTX units. Due to this fact, numerous fully-operational devices remain underused, which are available at an affordable price. First, this paper presents an analysis of the cryptocurrency market. Next, in this context, the results of research on the performance of NVIDIA graphics...
-
Virtual inertia in Electric Power System
PublikacjaThe article presents the idea of introducing virtual inertia system to the electric power systems. The virtual inertia aim is to reduce or eliminate the effect of reducing the inertia of the power system as a result of replacing classic electricity generating units with renewable renergy sources (RES). The considerations are ilustrated by a computational example.
-
Błędy w przedstawianiu wyników pomiarów i wartości wielkości fizycznych popełniane w pracach studenckich
PublikacjaArtykuł powstał na bazie doświadczeń zdobytych podczas pracy dydaktycznej autora jako wykładowcy i nauczyciela akademickiego prowadzącego zajęcia w Laboratorium Podstaw Metrologii. Przytoczono przykłady nieprawidłowości w przedsta-wianiu wyników pomiarów i wartości wielkości fizycznych pochodzące z prac pisemnych studentów i skonfrontowano je z zaleceniami Międzynarodowego Układu Jednostek Miar (SI), oraz polskimi aktami prawnymi.
-
Mathematical approach to design 3D scaffolds for the 3D printable bone implant
PublikacjaThis work demonstrates that an artificial scaffold structure can be designed to exhibit mechanical properties close to the ones of real bone tissue, thus highly reducing the stress-shielding phenomenon. In this study the scan of lumbar vertebra fragment was reproduced to create a numerical 3D model (this model was called the reference bone sample). New nine 3D scaffold samples were designed and their numerical models were created....
-
Knowledge and technology transfer in the Center for Scientific and Technical Information of the Wrocław University of Technology
PublikacjaKnowledge and Technology Transfer between a university and economic operators affects innovation and growth of competitiveness, as well as the development of a knowledge-based society. In the structures of Wroclaw University of Technology, regarded as one of the best and the most innovative technical universities in Poland, a number of units responsible for a wide understanding cooperation with the economy have been established....
-
High performance filtering for big datasets from Airborne Laser Scanning with CUDA technology
PublikacjaThere are many studies on the problems of processing big datasets provided by Airborne Laser Scanning (ALS). The processing of point clouds is often executed in stages or on the fragments of the measurement set. Therefore, solutions that enable the processing of the entire cloud at the same time in a simple, fast, efficient way are the subject of many researches. In this paper, authors propose to use General-Purpose computation...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K01
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - full run
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K06
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K04
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run (10s)
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K08
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K07
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K05
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K02
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate...
-
Wear in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K03
Dane BadawczeFriction and wear tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180 and 300s. (stored in separate folders).Specimen...
-
Block-based Representation of Application Execution on Modern Parallel Systems
PublikacjaThe chapter presents how to model execution of a parallel computational application that is to be executed in a large-scale parallel or distributed environment with potentially thousands to millions of execution units. The representation uses pre- viously attributes and factors representative of modern high performance systems including multicore CPUs, GPUs, dedicated accelerators such as Intel Phi.
-
Anna Wałek dr
OsobyDr Anna Wałek, Prezydent International Association of University Libraries (IATUL), dyrektor Biblioteki Politechniki Gdańskiej, ekspert w zakresie otwartego dostępu do zasobów naukowych (Open Science, Open Access, Open Research Data) oraz organizacji i zarządzania biblioteką naukową. Od lutego 2023 r. ekspert i Koordynator Hubu Wschodniego (East Hub) w ramach projektu Focusing on Open, Collaboration and Useful Science (EOSC Focus)...
-
Possibilities of applying standard tools of promotion in place marketing
PublikacjaThe purpose of this article is to present the tools of promotion that can be used by local government units in the developing and implementing of marketing strategies. The article evaluates a set of four basic tools of promotion comprising advertising, public relations and publicity, sales promotion and personal selling. This group was supplemented by direct marketing, presented from the point of view of communication via the Internet.
-
How to render FDTD computations more effective using agraphics accelerator.
PublikacjaGraphics processing units (GPUs) for years have been dedicated mostly to real time rendering. Recently leading GPU manufactures have extended their research area and decided to support also graphics computing. In this paper, we describe an impact of new GPU features on development process of an efficient finite difference time domain (FDTD) implementation.
-
The effect of nitrogen on the structure and thermal properties of beryllium-containing Na-(Li)-Si-O-N glasses
PublikacjaTwo oxynitride glass series with the composition of 35Na2O-5BeO-(60-x)SiO2-xSi3N4 and 9Li2O- 27Na2O-5BeO-(59-x)SiO2-xSi3N4, were prepared. The glasses' topography and structure were studied by Scanning Electron Microscopy and Raman spectroscopy. The composition was analyzed by Inductively Coupled Plasma Optical Emission Spectrometer, SEM-EDS and nitrogen and oxygen elemental analyzer. Na-(Li)-Be-silicate glasses were found to contain...
-
A coarse‐grained approach to NMR ‐data‐assisted modeling of protein structures
PublikacjaThe ESCASA algorithm for analytical estimation of proton positions from coarse-grained geometry developed in our recent work has been implemented in modeling protein structures with the highly coarse-grained UNRES model of polypeptide chains (two sites per residue) and nuclear magnetic resonance (NMR) data. A penalty function with the shape of intersecting gorges was applied to treat ambiguous distance restraints, which automatically...
-
Experimental Investigations on the Influence of Coil Arrangement on Melting/Solidification Processes
PublikacjaThe latent heat thermal energy storage units are very popular because of their high energy density and almost close to constant temperature during the charging/discharging. In the present study has been proposed new shell-and-coil geometry with a shifted coil position to enhance the performance of phase change thermal magazine. The experimental investigations have been performed both for the melting and solidification process of...
-
Practical aspects of design and operation of amphibious craft for rescue purposes
PublikacjaThe paper presents the selected problems of design and operation of amphibious craft for rescue purposes. The result of research on the amphibious rescue units allowed formulating the general conclusions with respect to the proper selection of the main design parameters, program of model tests and full scale trials for the amphibious craft. The most important design problems related to the water characteristics are presents and...
-
Wytwarzanie energii elektrycznej - diagnoza i terapia
PublikacjaW artykule przeanalizowano stan i dalszy rozwój krajowego sektora wytwarzania energii elektrycznej w świetle najnowszych raportów Międzynarodowej Agencji Energetycznej, wskazujących potencjalne trendy i perspektywy w światowej energetyce. Na tle przewidywanego wzrostu zapotrzebowania na energię elektryczną wskazano na możliwość istotnego ograniczenia emisji CO2 drogą zastąpienia przestarzałych, nieefektywnych...
-
Power enhancement of the Brayton cycle by steam utilization
PublikacjaThe paper presents thermodynamic analysis of the gas-steam unit of the 65 MWe combined heat and power station. Numerical analyses of the station was performed for the nominal operation conditions determining the Brayton and combined cycle. Furthermore, steam utilization for the gas turbine propulsion in the Cheng cycle was analysed. In the considered modernization, steam generated in the heat recovery steam generator unit is directed...
-
APPLICATION OF THE GWR MODEL FOR PREDICTING THE ROAD FATALITIES RATE ON THE ROAD NETWORK IN THE NUTS 3 REGIONS IN EUROPE ON THE EXAMPLE OF KUYAVIAN- -POMERANIAN VOIVODESHIP
PublikacjaThe article presents the application of the GWR (Geographically Weighted Regression) model to the description of differences in the level of road traffic safety in individual counties on the example of the Kuyavian-Pomeranian Voivodeship. The GWR model developed for counties, taking into account the diversity of NUTS 3 regions, can be a helpful tool for traffic safety management in voivodships and lower administrative units, and...
-
Comparison of Mathematical Models of Torque Transmitted by Multi-disc Wet Clutch with Experimental Results
PublikacjaIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
Experimental Study of Flow Rate in Hydraulic Satellite Motor with the Rotating Case at a Low Constant Rotational Speed
PublikacjaIn this article was described the methodology for the experimental study of flows in the prototype of a satellite hydraulic motor with a rotating body. The experimental tests of the motor were carried out at a low constant rotational speed in a wide range of pressure drop in this motor. The constant rotational speed of the motor was kept by a worm gear. Based on the test results, the leakage characteristics in the flat gaps of...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09A - full-run
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K09 - pre-run
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). No lubrication (DRY). Specim. set K05
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DRY. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30, 60, 180...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - PARAFFIN OIL. Specim. set K08
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: PARAFFIN OIL. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15, 30,...
-
VIbration monitoring in reciprocating siding friction tests. Ball-on-flat contact. Sintered alumina ceramics (98%). Lubricant - DISTILLED WATER. Specim. set K02
Dane BadawczeVIbration monitoring in reciprocating siding friction tests in ball-on-flat contact. Both specimens made of sintered alumina ceramics (98%) - self-mated contact.Linear reciprocating motion.Lubrication: DISTILLED WATER. Sliding velocity (peak): 0.1 m/s. Load (normal force): 5N. Test rig: TPZ-1 Tribometer.Running time: progressive increments of 10, 15,...