Wyszukiwarka
Wyniki wyszukiwania dla: MIKROMETR
-
OVERALL SET OF BANDSAW TEETH VERSUS METHODS OF MEASUREMENTS
PublikacjaThis article deals with the impact of the manual methods of measurement on the overall set measurement results. It describes the results of the measurement of bandsaw teeth kerf with the use of a micrometer and a digital calliper. It is commonly known that the cutting process causes the wear of cutting tools. The wear of the cutting edge depends on the cutting conditions as well as on the mechanical properties of the processed...
-
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Zintegrowana obróbka tulei cylindrów hydraulicznych głowicami roztaczająco-nagniatającymi
PublikacjaOpisano zintegrową technologię tulei cylindrów hydraulicznych polegającą na obróbce skrawaniem i powierzchniowej obróbce plastycznej przez nagniatanie. Przedstawiono konstrukcję specjalnych głowic roztaczajaco-nagniatających, stanowisko obróbkowe i rezultaty obróbki tulei o średnicy otworu 100H7 i długości 1400 mm. Osiągnięto chropowatość powierzchni Ra = 0,6 do 0,32 mikrometra. Proponowana technologia cylindrów hydraulicznych...
-
Compatible DC and small-signal MOSFET models for radio and microwave frequency simulation
PublikacjaZaprezentowano nowy model stałoprądowy tranzystora MOS i kompatybilny z nim uogólniony nie-quasi-statyczny model małosygnałowy. Model stałoprądowy został eksperymentalnie zweryfikowany dla tranzystorów MOS o długości kanału od 75 nm do kilkunastu mikrometrów, a model małosygnałowy od zera herców do 30 GHz.
-
Morphology of polyurethanes revisited by complementary AFM and TEM
PublikacjaPrzedmiotem badań mikroskopowych TEM i AFM były lane segmentowe poliuretany o zawartości 30 i 50% segmentu sztywnego. Stwierdzono obecność sferolitów (poziom mikrometrów), fibryl i globul. Ponadto zastosowanie AFM pozwoliło na zbadanie nanomorfologii badanych poliuretanów. Zaobserwowano krótkie, cylindropodobne domeny segmentów sztywnych rozproszone w matrycy segmentów giętkich.
-
Method of determining to the solving of friction forces on the tissue surface in bioreactor = Numeryczny wkład do wyznaczania sił tarcia na powierzchni tkanki w bioreaktorze
PublikacjaNiniejsza praca przedstawia metodę całkowania równań ruchu lepko-sprężystej cieczy odżywczej w cienkiej warstwie granicznej na powierzchni komórek chrząstki (chondrocytów), podczas nieustalonego procesu ich hodowli w bioreaktorze. Układ równań podstawowych w trójwymiarowej przestrzeni składa się z trzech równań zachowania pędu oraz z równania ciągłości. Proces hodowli komórek w bioreaktorach zależy od własności cieczy odżywczych.Ponieważ...
-
Synthesis and properties of UV-curable poly(imideurethane) acrylates.
PublikacjaOtrzymano światłoczułe poli(imidouretano) akrylany (PIUA) które użyte zostały do wytwarzania światłoczułych kompozycji z dodatkiem reaktywnych rozcieńczalników i różnych fotoinicjatorów. Uzyskane z nich cienkie warstwy polimerowe ulegały usieciowaniu pod działaniem światłaUV w ciągu 10-30 sek. W badaniach fotolitograficznych uzyskano z ich użyciem ścieżki izolacyjne o rozdzielczości 10 mikrometrów. Usieciowane PIUA scharakteryzowano...
-
Model of heat transfer in the stagnation point of rapidly evaporating microjet
PublikacjaThe paper presents investigation into the single water microjet surface cooling producing evaporating film. Reported tests were conducted under steady state conditions. Experiments were conducted using the nozzle size of 70 and 100 mikrometer respectively. In the course of investigations obtained were experimental relations between heat flux and wall superheating. It was proved that the phenomenon is similar to that of pool boiling...
-
Mesoscopic impedance analysis of solid materials surface
PublikacjaSeveral techniques have been developed in order to characterize electrical properties of surfaces in micrometer/nanometer scale. Obtaining of the spatial distribution of sample resistance, capacitance or potential requires separate measurements performed in different scanning modes. On the other hand, analysis of the frequency response of investigated system enables determination of several physical quantities in single measurement...
-
Światłowodowa koherentna tomografia optyczna (OCT) w zastosowaniach technicznych
PublikacjaKoherentna tomografia optyczna jest szybko rozwijającą się metodą obrazowania przekrojów wewnętrznych struktur. Pierwotnie używana do celów biomedycznych, może znaleźć szerokie zastosowanie do badań materiałowych. Jest to uniwersalna technika pomiarowa charakteryzująca się wysoką rozdzielczością (rzędu pojedynczych mikrometrów), połączoną z możliwością obrazowania optycznych ośrodków silnie rozpraszających światło. W artykule przedstawione...
-
Światłowodowa koherentna tomografia optyczna (OCT) w zastosowaniach technicznych
PublikacjaKoherentna tomografia optyczna (ang. Optical Coherence Tomography - OCT) jest szybko rozwijającą się metodą obrazowania przekrojów wewnętrznych struktur. Pierwotnie używana do celów biomedycznych, może znaleźć szerokie zastosowanie do badań materiałowych. Jest to uniwersalna technika pomiarowa charakteryzująca się wysoką rozdzielczością (rzędu pojedynczych mikrometrów) połączoną z możliwością obrazowania optycznych ośrodków silnie...
-
Przemysłowe zastosowania optycznej tomografii koherentnej
PublikacjaOptyczna tomografia koherentna (OCT) jest nowoczesną techniką obrazowania wewnętrznej struktury obiektów rozpraszających światło. Główne zastosowania OCT należą do dziedziny obrazowania medycznego, jednak prowadzony jest także szereg badań nad przemysłowymi aplikacjami tej metody. Zaletą OCT jest możliwość tomograficznego obrazowania z rozdzielczością rzędu pojedynczych mikrometrów w sposób szybki i nieinwazyjny. W niniejszym artykule...
-
Structure changes in (Bi-Pb)-Sr-Ca-Cu-O glass ceramics during the first minutes of crystallization.
Publikacja(Bi0.8Pb0.2)4Sr3Ca3Cu4Ox szkło otrzymano standardową metodą chłodzenia stopionych substratów. Częściowo skrystalizowane próbki otrzymano poprzez wygrzewanie szkła w temperaturze między 700stC i 870stC. Obecność faz krystalicznych badano metodą dyfrakcji rentgenowskiej w temperaturze pokojowej oraz w temperaturze krystalizacji. Stwierdzono obecność faz nadprzewodzących (Bi0.8Pb0.2)2Sr2CuOx, (Bi0.8Pb0.2)2Sr2CaCu2Ox i (Bi0.8Pb0.2)2Sr2Ca2Cu3Ox...
-
Surface treatment of porous Ti13Nb13Zr alloy for biomedical applications
PublikacjaPrzeprowadzono badania materiału porowatego, przeznaczonego na implanty ortopedyczne, wytworzonego metodą metalurgii proszków ze stopu Ti13Nb13Zr. Proszki z badanego stopu uzyskano metodą rozpylania plazmowego. Otrzymano próbki o otwartej porowatej strukturze, stopniu porowatości do 68% i średniej wielkości porów w przedziale 30-150 mikrometrów. Obróbka próbek porowatych - utlenianie termiczne, chemiczne i/lub elektrochemiczne...
-
Increased resonance energy transfer between fluorophores bound to DNA in proximity to metallic silver particles.
PublikacjaZbadano wpływ nanocząstek metalicznego srebra na rezonansowe przekazywanie energii między fluoroforami związanymi z DNA. Donor (pochodna kumaryny) i akceptor (Cy3) umieszczono na przeciwległych końcach DNA o strukturze podwójnej helisy i o 23 parach bazowych. W nieobecności cząstek srebra wydajność przekazywania energii w tym układzie wynosiła ok. 9%, zaś po umieszczeniu go między kwarcowymi płytkami pokrytymi filmem wysepek...
-
Corrosion Inhibition of Aluminium Alloy AA6063-T5 by Vanadates: Local Surface Chemical Events Elucidated by Confocal Raman Micro-Spectroscopy
PublikacjaChemical interactions between aqueous vanadium species and aluminium alloy AA6063-T5 were investigated in vanadate-containing NaCl solutions. Confocal Raman and X-ray photoelectron spectroscopy experiments were utilised to gain insight into the mechanism of corrosion inhibition by vanadates. A greenish-grey coloured surface layer, consisting of V+4 and V+5 polymerized species, was seen to form on the alloy surface, especially on...
-
Thermoelectric properties of bismuth-antimony-telluride alloys obtained by reduction of oxide reagents
PublikacjaThe BieSbeTe alloys with different Bi/Sb/Te ratio were fabricated by an innovative method. For that purpose the oxide reagents were melted at high temperature, then quenched to form pellets, milled to a powder and finally reduced in hydrogen at various temperatures. Complex structures consisting of connected thin layers forming a continuous path between nano- and micrometer size grains have been obtained. The electrical conductivity,...
-
Laserowy wibrometr skanujący PSV-400-M4
Aparatura BadawczaLaserowy wibrometr skanujący PSV-400-M4
-
HPLC-DAD in identification and quantification of selected coumarins in crude extracts from plant cultures of Ammi majus and Ruta graveolens.
PublikacjaW pracy opisano wyniki badań nad opracowaniem metody rozdzielania, identyfikacji i oznaczania wybranych kumaryn i funarokumaryn w surowych ekstraktach roślinnych z Ammi majus i Ruta graveolens hodowanych pojedynczo lub w kokulturach. Zbadano przydatność trzech głównych składników eluentu, stosowanych w układach faz odwróconych i różnych programów elucji: woda- acetonitryl(ACN)- metanol (MeOH)- tetrahydrofuran (THF). W optymalnej...
-
Stan wiedzy na temat analizy pyłów z wykorzystaniem mikroskopii elektronowej
PublikacjaDo oceny stopnia zanieczyszczenia środowiska wykorzystuje się różnorodne metody i techniki analityczne. Jedną z metod jest mikroskopia elektronowa, która może być wykorzystana także do monitoringu jakości powietrza, a w szczególności pyłów, których wielkość jest tak mała, że nie mogą być obserwowane z wykorzystaniem mikroskopii optycznej.W 2006 roku badania pyłów z wykorzystaniem mikroskopii elektronowej rozpoczęto także na Politechnice...
-
Effect of Microplastics Pollution on Hydrogen Production from Biomass: A Comprehensive Review
PublikacjaHydrogen production from biomass and organic wastes is considered as a potential alternative energy source and is known as a clean and CO2-free fuel energy carrier. H2 is considered very promising among the other energy sources; therefore, the effective conversion of biomass and organic solid waste to this secondary energy source is urgently sought. As a result, it is of importance to assess the impact of the existence of microplastics...
-
Effect of sintering temperature on electrochemical performance of porous SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) oxygen electrodes for solid oxide cells
PublikacjaThis work evaluates the effects of the sintering temperature (800 °C, 900 °C, 1000 °C) of SrTi1-xFexO3-δ (x = 0.35, 0.5, 0.7) porous electrodes on their electrochemical performance as potential oxygen electrode materials of solid oxide cells. The materials were prepared by a solid-state reaction method and revealed the expected cubic perovskite structure. After milling, the powders were characterised by a sub-micrometre particle...
-
Assessment of organic coating degradation via local impedance imaging
PublikacjaThe paper presents a new approach to organic coating condition evaluation at micrometer scale using localized impedance measurements. It is based on atomic force microscopy (AFM) in contact mode. Impedance is measured between conductive AFM tip and metal substrate covered with organic coating. A single-frequency voltage perturbation signal is applied between the electrodes and current response signal is registered. As the tip is...
-
Micro- and nano-level of bio-joint lubrication = Smarowanie biołożysk na poziomie mikro i nano
PublikacjaSmarowanie stawów człowieka koncentruje się w głównej mierze na tarciu granicznym oraz na tarciu mieszanym w cienkiej warstwie cieczy synowialnej zalegającej pomiędzy łatwo odkształcalnymi powierzchniami miękkiej chrząstki stawowej, na której wysokości chropowatości zmieniają się z czasem trwania procesu smarowania.Wartości sił tarcia granicznego ulegają zmianie w przypadku zmian wysokości nierówności dochodzących do dziesiątych...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 0 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 40 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 30 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 200 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 20 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 80 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 170 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 20 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 140 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 130 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 50 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 120 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 110 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 130 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 90 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 120 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 200 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 170 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 90 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 180 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 140 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 60 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 190 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 40 um (serie 1)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 70 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...
-
Distance measurement with the low coherent interferometer with silver mirror (the source wavelegth 1310 nm) - 180 um (serie 2)
Dane BadawczeThe obtained data was acquired by the interferometric fiber-optic sensor of distance. The setup was constructed of a broadband light source working at the central wavelength of 1310 nm, an optical spectrum analyzer, and a fiber-optic 2x1 coupler (with the power split 50:50). All elements were connected by standard single-mode optical fibers. The measurement...