Wyszukiwarka
Katedra Fizyki Ciała Stałego
Publikacje
Filtry
wszystkich: 997
Katalog Publikacji
Rok 2015
-
Structure and thermoelectric properties of Bi–Te alloys obtained by novel method of oxide substrates reduction
PublikacjaA novel method of thermoelectric materials fabrication has been developed. Oxide reagents have been melted at high temperature in air, quenched, milled to powder and reduced in hydrogen to form Bi–Te alloys. Structural and thermoelectric properties of samples have been investigated depending on initial composition and temperature of reduction process. Sample 25Bi2O3–75TeO2 reduced at 340 °C for 10 h has been found to be a p-type...
-
STRUKTURA I TRANSPORT ELEKTRYCZNY UKŁADU Li-Ti-O
PublikacjaTytanian litu Li1+xTi2-xO4 (0 ≤ x ≤ 1/3) jest tlenkiem, który dzięki swym unikalnym właściwościom od połowy lat 70 pozostaje źródłem zainteresowania i obiektem badań naukowców. Jedną z najciekawszych właściwości tego związku jest przejście w stan nadprzewodzący poniżej temperatury około 13 K i jej silna zależność od stechiometrii układu. Oprócz nadprzewodnictwa wyróżniają go ciekawe właściwości elektrochemiczne oraz fotokatalityczne,...
-
Superconductivity in the niobium-rich compound Nb5Se4
PublikacjaThe niobium rich selenide compound Nb5Se4 was synthesized at ambient pressure by high-temperature solid–state reaction in a sealed Ta tube. Resistivity and heat capacity measurements reveal that this compound is superconducting, with a Tc = 1.85K. The electronic contribution to the specific heat γ and the Debye temperature are found to be 18.1 mJmol−1K−2 and 298 K respectively. The calculated electron-phonon coupling constant λep...
-
Synthesis and modification of reduced graphene oxide aerogels for biofuel cell applications
PublikacjaWe have carried out the preparation of reduced graphene oxide aerogels using eco-friendly method that is based on the Hummers method of graphite oxidation without the use of NaNO3 that produces toxic gases. To obtain a porous 3D structure of reduced graphene oxide, we performed the hydrothermal reduction at elevated temperature. We also prepared the rGO aerogel/CNT composite using multiwalled carbon nanotubes as linkers. The rGO...
-
Tailoring Graphene to Achieve Negative Poisson's Ratio Properties
PublikacjaGraphene can be made auxetic through the introduction of vacancy defects. This results in the thinnest negative Poisson's ratio material at ambient conditions known so far, an effect achieved via a nanoscale de-wrinkling mechanism that mimics the behavior at the macroscale exhibited by a crumpled sheet of paper when stretched.
-
The influence of thermal conditions on V2O5 nanostructures prepared by sol-gel method
PublikacjaThis work presents the result of structure investigations ofV 2O5 nanorods grown from thin films and powders prepared by sol-gel method. To examine the best temperature of nanorods crystallization, thin films deposited by spin-coating method on quartz glass or silicon substrates and bulk xerogel powders were annealed at various temperatures ranging from 100∘C to 600∘C. The structure of the samples was characterized by X-ray diffraction...
-
Theory of valence-band and core-level photoemission from plutonium dioxide
PublikacjaThe correlated-band theory implemented as a combination of the local-density approximation with the dynamical mean-field theory is applied to PuO2. An insulating electronic structure, consistent with the experimental valence-band photoemission spectra, is obtained. The calculations yield a nonmagnetic ground state that is characterized by a noninteger filling of the plutonium 5f shell. The noninteger filling as well as the satellites...
-
Thermodynamics of solid phases containing rare earth oxides
PublikacjaRare earth elements (RE) are incorporated into a large variety of complex oxide phases to provide tailored mechanical, electrical, optical, and magnetic properties. Thermodynamics control phase stability, materials compatibility in use, corrosion, and transformation. This review presents, in one compilation, the thermodynamic properties of a large number of such materials and discusses systematic trends in energetics and the factors...
-
Thin layer of ordered boron-doped TiO2 nanotubes fabricated in a novel type of electrolyte and characterized by remarkably improved photoactivity
PublikacjaThis paper reports a novel method of boron doped titania nanotube arrays preparation by electrochemical anodization in electrolyte containing boron precursor – boron trifluoride diethyl etherate (BF3 C4H10O), simultaneously acting as an anodizing agent. A pure, ordered TiO2 nanotubes array, as a reference sample, was also prepared in solution containing a standard etching compound: ammonium fluoride. The doped and pure titania...
-
Three electrode configuration measurements of electrolyte-diffusion barrier-cathode interface
PublikacjaMeasurements of a system consisting of cathode/doped ceria diffusion barrier/doped zirconia electrolyte were made using two- and three-electrode configuration. Results obtained on a three-electrode measurement configuration were compared with and reflect the results obtained in two-electrode configuration. Three-electrode measurements allowed separating the impact of the symmetrical interface in the investigated system. They also...
-
Tin oxide nanoparticles from laser ablation encapsulated in a carbonaceous matrix – a negative electrode in lithium-ion battery applications
PublikacjaThis report concerns carbonaceous electrodes doped with tin(II) oxide nanoparticles. Tin nanoparticles are obtained by pulsed laser ablation in water. Crystalline nanoparticles have been encapsulated in a carbonaceous matrix formed after pyrolysis of a mixture consisting of tin/tin(IV) oxide nanoparticles and gelatine. The obtained material is characterized by means of X-ray diffraction, selected area diffraction, scanning electron...
-
Transition Metal Oxides influence on phosphate and borate glasses structure
PublikacjaBorate and phosphate glasses possess many potential luminescence and optical applications. With their low melting point, they are one of the most often studied amorphous materials. In recent years these glasses, doped with transition metal oxides (TMO), gained much attention due to their tunable structural and thermal properties. Review of systems containing TMOs was presented. Additionally synthesis of binary MnO-P2O5 and MnO-B2O3...
-
Unusual behaviour of (Np,Pu)B2C
PublikacjaTwo transuranium metal boron carbides, NpB2C and PuB2C have been synthesized by argon arc melting. The crystal structures of the {Np,Pu}B2C compounds were determined from single-crystal X-ray data to be isotypic with the ThB2C-type (space group R3m, a = 0.6532(2) nm; c = 1.0769(3) nm for NpB2C and a = 0.6509(2) nm; c = 1.0818(3) nm for PuB2C; Z = 9). Physical properties have been derived from polycrystalline bulk material in the...
-
Visible light activity of rare earth metal doped (Er3+, Yb3+ or Er3+/Yb3+) titania photocatalysts
PublikacjaA series of Er3+-TiO2, Yb3+-TiO2 and Er3+/Yb3+-TiO2 photocatalysts were obtained via sol-gel method, using rare earth metal (RE) precursor ranging from 0.25 to 10 mol%. The experiments demonstrated that phenol in aqueous solutions was successfully degraded under visible light (> 450 nm) using RE3+-TiO2. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron emission spectroscopy (XPS), UV-Vis...
-
Właściwości redukowanych szkieł Ge-Sb-O dla urządzeń termoelektrycznych
PublikacjaPraca zawiera wyniki badań strukturalnych oraz właściwości termoelektrycznych tlenkowego szkła antymonowo-germanianowego, poddanego redukcji w atmosferze wodoru, jako potencjalnego materiału do zastosowań w urządzeniach termoelektrycznych. Otrzymane rezultaty analizy dyfrakcyjnej oraz analizy mikroskopowej dały informacje o strukturze i składzie próbki. Potwierdziły one fakt powstawania warstwy powierzchniowej zredukowanych granul...
-
Wpływ procesu redukcji na właściwości strukturalne i mechaniczne szkieł tlenkowych z grupy (Pb,Bi)-(Si,Ge)-O
PublikacjaW pracy zbadano wpływ procesu redukcji w wodorze prowadzonej w temperaturze 380°C na mikrostrukturę i skład pierwiastkowy próbki szkła Bi0.4Pb0.2Si0.4Ox. Wykazano, że na skutek redukcji w próbce tworzy się wyraźnie odseparowana wierzchnia warstwa o grubości ok. 50µm, która jest zubożona w tlen i charakteryzuje się lepszą przewodnością elektryczną. Stwierdzono również, że na powierzchni szkła tworzą się granule metalicznego bizmutu...
-
Wpływ procesu redukcji na właściwości strukturalne i mechaniczne szkieł tlenkowych z grupy (Pb,Bi)-(Si,Ge)-O = Influence of reduction process on the structural and mechanical properties of (Pb,Bi)-(Si,Ge)-O oxide glasses
PublikacjaThe effect of the reduction process in H2 at 380 °C on the microstructure and elemental composition of a glass Bi0.4Pb0.2Si0.4Ox has been investigated. It has been shown that after reduction a clearly separated top layer with a thickness of approx. 50 µm was formed on the surface of the sample. This layer is depleted of oxygen and has higher electrical conductivity than the interior of the glass. It has also been found that some...
Rok 2014
-
237Np Mössbauer effect study on NpFeAsO
PublikacjaWe report 237Np Mössbauer measurements on NpFeAsO. The Np atoms were found to occupy only one crystallographic site. The value of the isomer shift (δ ∼ 9.1 mm s−1 versus NpAl2) indicates a 5f4 electronic configuration (Np3+ ions). The magnetic ordering of the Np sublattice below 60 K is established and the saturated ordered magnetic moment is determined to be 1.73μB at 3.6 K. The unique set of hyperfine parameters exclude a modulated...
-
Aggregation of Rhodamine 6G in titanium dioxide nanolayers and bulk xerogels
PublikacjaNanolayers and bulk xerogels of Rhodamine 6G (Rh6G) in titanium dioxide (Rh6G/TiO2) were prepared using the sol–gel method. The spectroscopic and structural properties of these two types of hybrid matrices were studied as a function of dye concentration. In both cases absorption, fluorescence and time resolved emission spectra show the formation of fluorescent aggregates. The observed stronger changes in characteristics of bulk...
-
Badania kompozytów na bazie niestechiometrycznego tytanianu strontu -Sr1-xTi0,98Nb0,02O3- jako potencjalnej anody dla SOFC
PublikacjaW celu uzyskania jak najwyższej przewodności elektrycznej oraz ograniczenia procesu dyfuzji strontu do warstw sąsiadujących wytworzono tytanian strontu domieszkowany niobem z niedoborem strontu do 9% molowych. Następnie materiał ten zastosowano jako składnik przewodzący elektronowo w kompozytach z tlenkiem cyrkonu stabilizowanego tlenkiem itru (YSZ). Kompozyty scharakteryzowano pod względem właściwości istotnych z punktu widzenia...
-
Badania kompozytów na bazie niestechiometrycznego tytanianu strontu Sr1-xTi0,98Nb0,02O3-YSZ jako potencjalnej anody dla SOFC
PublikacjaW celu uzyskania jak najwyższej przewodności elektrycznej oraz ograniczenia procesu dyfuzji strontu do warstw sąsiadujących wytworzono tytanian strontu domieszkowany niobem z niedoborem strontu do 9% molowych. Następnie materiał ten zastosowano jako składnik przewodzący elektronowo w kompozytach z tlenkiem cyrkonu stabilizowanego tlenkiem itru (YSZ). Kompozyty scharakteryzowano pod względem właściwości istotnych z punktu widzenia...
-
Biobatteries and biofuel cells with biphenylated carbon nanotubes
PublikacjaSingle-walled carbon nanotubes covalently biphenylated are used for the construction of cathodes in a flow biobattery and in flow biofuel cell. Zinc covered with a hopeite layer is the anode in the biobattery and glassy carbon electrode covered with bioconjugates of single-walled carbon nanotubes with glucose oxidase and catalase is anode of the biofuel cell. The potentials of the electrodes are measured vs. the Ag/AgCl reference...
-
Cadmium complex possessing simultaneously silanethiolato- and dithiocarbamato-ligands. A novel single-source precursor of cadmium sulfide
PublikacjaThermal decomposition of suitable coordination compounds may be used as efficient route for fabrication of semiconducting layers. A new potential CdS precursor—a cadmium complex with all-sulfur Cd-coordination sphere [Cd{l-SSi(OBut)3}(S2CNC4H8)]2 (1) —has been prepared and its properties are investigated. The complex was obtained in the reaction between dimeric bis(tri-tert-butoxysilanethiolato) cadmium(II) [Cd{SSi(OBut)3}2]2 and...
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublikacjaIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Crystal structure and electronic structure of CePt2In7
PublikacjaWe report a corrected crystal structure for the CePt2In7 superconductor, refined from single crystal x-ray diffraction data. The corrected crystal structure shows a different Pt–In stacking along the c-direction in this layered material than was previously reported. In addition, all of the atomic sites are fully occupied with no evidence of atom site mixing, resolving a discrepancy between the observed high resistivity ratio of...
-
Czujniki tlenu pracujące bez układu odniesienia
PublikacjaW celu wyznaczenia stężenia lub ciśnienia parcjalnego tlenu w danym środowisku zastosować można potencjometryczne, amperometryczne lub rezystancyjne czujniki tlenu. W niniejszej pracy scharakteryzowane zostaną wszystkie trzy typy urządzeń. Szczególnie interesujące są czujniki amperometryczne i rezystancyjne, gdyż nie wymagają stosowania układu odniesienia i dzięki temu są to rozwiązania stosunkowo proste, tanie i trwałe.
-
Density functional theory calculations on entire proteins for free energies of binding: Application to a model polar binding site
PublikacjaIn drug optimization calculations, the molecular mechanics Poisson-Boltzmann surface area (MM-PBSA) method can be used to compute free energies of binding of ligands to proteins. The method involves the evaluation of the energy of configurations in an implicit solvent model. One source of errors is the force field used, which can potentially lead to large errors due to the restrictions in accuracy imposed by its empirical nature....
-
Determination of Mechanical Properties of P91 Steel by Means of Magnetic Barkhausen Emission
PublikacjaIn this work, an attempt at determination of mechanical properties by means of a method based on magnetic Barkhausen emission measurements was proposed. The specimens made of P91 steel were subjected to creep or plastic flow which were interrupted after a range of selected time periods in order to achieve specimens with an increasing level of strain. Subsequently, measurements of magnetic Barkhausen emission were carried out, and...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublikacjaLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Elastyczne nanokopozytowe pianki poliuretanowe
PublikacjaPrzedmiotem badań były elastyczne pianki poliuretanowe modyfikowane nanonapełniaczem z grupy glinokrzemianiów warstwowych oraz fosforoorganicznym związkiem zmniejszającym palność.
-
Electrical properties and structure of lead-borate glass containing iron ions.
PublikacjaThe ac and dc conductivity in iron–lead-borate glass samples was investigated in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by the means of atomic force microscopy (AFM) and the crystalline phases (if present) were identified by the means of X-ray diffractometry. Two types of ac electrical behaviour were observed. The first group of glass samples which...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublikacjaThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
Evidence for SrHo2O4 and SrDy2O4 as model J1- J2 zigzag chain materials
PublikacjaNeutron diffraction and inelastic spectroscopy is used to characterize the magnetic Hamiltonian of SrHo2O4 and SrDy2O4. Through a detailed computation of the crystal-field levels we find site-dependent anisotropic single-ion magnetism in both materials, and diffraction measurements show the presence of strong one-dimensional spin correlations.Our measurements indicate that competing interactions of the zigzag chain, combinedwith...
-
Evolution of the nanostructure of Pt and Pt–Co polymer electrolyte membrane fuel cell electrocatalysts at successive degradation stages probed by X-ray photoemission
PublikacjaWe present a set of XPS (X-ray photoemission spectroscopy) measurements and detailed data-analysis of electrodes for polymer electrolyte membrane fuel cell (PEMFC) based on carbon supported catalysts (Pt and Pt–Co) subjected to a step-like potential cycling (accelerated degradation test). The results of the measurements complete and corroborate parallel TEM (transmission electron microscopy), XRD (X-ray diffraction) and XAS (X-ray...
-
Hierarchia czynników wpływu w diagnostyce komponentów stalowych metodą statycznego pola rozproszonego
PublikacjaWśród technik badań nieniszczących obiektów stalowych (NDT) szczególną rolę pełnią techniki elektromagnetyczne, jako relatywnie tanie, czyste, szybkie i adaptowalne. Mają one jednak istotne ograniczenia, o których wydają się zapominać praktycy promujący tzw. metodę magnetycznej pamięci metali (ang. magnetic metal memory, MMM). Szczególnie dyskusyjna jest postulowana przez nich możliwość ilościowej korelacji charakterystyk pola...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublikacjaIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
Influence of plastic deformation on stray magnetic field distribution of soft magnetic steel sample
PublikacjaThe effect of various combinations of conditions, i.e., presence of the Earth’s magnetic field during and after deformation on the distribution of stray magnetic field of S355 steel sample, which is locally deformed, was investigated. Some of the stages of the experiment were carried out in zero magnetic field. Compensation of the Earth’s magnetic field was obtained by the application of a pair of Helmholtz coils. These coils are...
-
Interaction of SrTi0.65Fe0.35O3-δ with LaNi0.6Fe0.4O3-δ, La0.6Sr0.4Co0.2Fe0.8O3-δ and Ce0.8Gd0.2O2-δ
PublikacjaIron doped strontium titanates SrTi1-xFexO3-δ are perovskites of versatile properties. They can be used in solid oxide fuel cells or high temperature oxygen sensors. Their reactivity with electrolyte materials, cathode buffer layer materials, other cathode materials or current collector layers has not been fully tested. In this study we use X-ray diffraction to check SrTi0.65Fe0.35O3-δ compatibility with Ce0.8Gd0.2O2-δ (used as...
-
Katalizatory reakcji elektrochemicznych w tlenkowych ogniwach paliwowych zasilanych biogazem
PublikacjaJednym z potencjalnych obszarów zastosowań tlenkowych ogniw paliwowych jest energetyka rozproszona, gdzie paliwem mógłby biogaz pochodzący z oczyszczalni ścieków, wysypisk, gospodarstw rolnych. Obecnie stosowane na skalę komercyjną rozwiązania technologiczne uniemożliwiają wykorzystanie paliwa w postaci biogazu m.in. ze względu na niską odporność anody na osadzanie węgla oraz niewystarczającą aktywność katalityczną dla elektrochemicznego...
-
Kontrola parametrów obwodu wymuszającego w quasi-statycznych magnetycznych badaniach nieniszczących stali, cz. I: Model analityczny i 2D
PublikacjaW artykule zaprezentowane zostało dwuwymiarowe modelowanie Metodą Elementów Skończonych (MES) układu do badań nieniszczących (ang. non-destructive testing, w skrócie NDT), składającego się z elektromagnesu jarzmowego i płyty ferromagnetycznej magnesowanej w sposób quasi-statyczny. Wykazane zostały ograniczenia stosowalności opartych na równaniach Maxwella obliczeń analitycznych 1D, które przynoszą zadowalające wyniki jedynie w...
-
KTaO3-based nanocomposites for air treatment
PublikacjaThe advantage is that photocatalytic methods allow removing VOCs, NOx, SO2, deodorants, and microorganisms at the same system. The new third generation of photoactive materials activated by low powered and low cost irradiation sources (such as LEDs or black fluorescent UV lamps) can be used as photocatalysts in air purification systems. A series of single semiconductors and their nanocomposites combination were prepared using hydrothermal...
-
Lanthanide co-doped TiO2: the effect of metal type and amount on surface properties and photocatalytic activity
PublikacjaPreparation of new rare earth metal-containing TiO2 nanocomposites (Nd3+/Er3+, Nd3+/Eu3+, Eu3+/Ho3+-TiO2) using sol–gel route and their photoactivity under visible and ultraviolet light is reported. The obtained photocatalysts were subsequently characterized by Brunauer–Emmett–Teller (BET) method, UV–Vis diffuse-reflectance spectroscopy (DRS), luminescence spectroscopy, X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction...
-
Materiały biozgodne i specjalnego przeznaczenia
PublikacjaW książce przedstawiono ogólną charakterystykę materiałów używanych w medycynie i laboratoriach klinicznych. Opisano wyjaławianie materiałów medycznych; mteriały okulistyczne, soczewki kontaktowe, szkła okularowe, enzymatyczne oczyszczanie soczewek kontaktowych, płyny, krople i maści do oczu; materiały dentystyczne: wiertła, pasty szlifierskie, wypełnienia; materiały na implanty metalowe, ceramiczne, z tworzyw sztucznych; cementy...
-
Methods of ZnO nanoparticles synthesis
PublikacjaZinc oxide nanostructures are interesting nanomaterials with a wide range of applications. Since the physical and chemical properties of ZnO nanoparticles are influenced both by their shape and size, a control of morphology of ZnO structures is needed for their commercial usage. Different chemical, physical, and biological methods used to produce ZnO nanostructures can be found in the literature. The production of ZnO nanoparticles...
-
Metodyka wykonywania pomiarów oraz ocena niepewności i błędów pomiaru
Publikacjaelem każdego ćwiczenia w laboratorium studenckim jest zmierzenie pewnych wielkości, a następnie ob- liczenie na podstawie tych wyników pomiarów wartości wielkości badanej. Rezulta- tem końcowym badań jest nie tylko otrzymany wynik liczbowy. Nie mniej ważne jest dokonanie oceny dokład- ności pomiaru oraz opraco- wanie wniosków końcowych. Warto zadać sobie pytanie: czy to, co zostało zmierzone, ma sens i co z tego wynika?...
-
Metodyka wytwarzania tlenkowych ogniw paliwowych oraz pomiaru ich parametrów elektrycznych w warunkach laboratoryjnych
PublikacjaCelem opracowania jest zaprezentowanie metodyki przygotowania oraz pomiaru parametrów elektrycznych tlenkowych ogniw paliwowych z anodą kompozytową na bazie perowskitu. Częściowo procedura ta była opisana w rozprawie doktorskiej autorki pt. „Właściwości strukturalne i transportowe kompozytów tytanianu strontu z tlenkami przewodzącymi jonowo” (Gdańsk 2013).
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublikacjaThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
Morfologia, w³aoeciwooeci mechaniczne i termiczne elastycznych pianek poliuretanowych modyfikowanych glinokrzemianami warstwowymi
PublikacjaWytwarzane z udzia³em poligliceryny elastyczne pianki poliuretanowe modyfikowano za pomoc¹ montmorylonitu sodowego (bentonitu, MMT), mieszaniny bentonitu i bezhalogenowego fosforoorganicznego zwi¹zku zmniejszaj¹cego palnooeæ (Fyrol PNX) oraz, stanowi¹cego nape³niacz hybrydowy, bentonitu modyfikowanego wykorzystywanym uniepalniaczem. Badano mikrostrukturê, w³aoeciwooeci mechaniczne i termiczne modyfikowanych pianek poliuretanowych....
-
Nanostructure and dielectric behavior of vanadate glasses containing BaTiO3
PublikacjaThe ac and dc electrical conductivity of barium titanate doped bismuth-vanadate as-quenched and heat-treated materials was measured in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K with the impedance spectroscopy method. The microstructure was investigated by means of XRD, scanning electron microscopy (SEM), atomic force microscopy (AFM) and confocal microscopy. The obtained results showed...