Filters
total: 420
filtered: 374
Search results for: REACTION FORCES
-
Influence of the shoe type on the ground reaction forces
PublicationThe aim of this work was to estimate a relationship between the type of the footwear and ground reactions. Differences in medio-lateral, anterior-posterior and vertical reactions are compared for different shoe-types for male and female volunteers. Each of the participants gait was recorded in case of different shoes and without them, also stabilograms were analyzed. Results revealed differences in ground reaction forces for different...
-
The Influence of External Additional Loading on the Muscle Activity and Ground Reaction Forces during Gait
PublicationAsymmetrical external loading acting on the usculoskeletal system is generally considered unhealthy. Despite this knowledge, carrying loads in an asymmetrical manner like carrying on one shoulder, with one hand, or on the strap across the torso is a common practice. This study is aimed at presenting the effects of the mentioned load carrying methods on muscle activity assessed by using thermal field and ground reaction forces....
-
The nonlinear effects of sound in a liquid with relaxation losses
PublicationThe nonlinear effects of sound in electrolyte with a chemical reaction are examined. The dynamic equations that govern non-wave modes in the field of intense sound are derived, and acoustic forces of vortex, entropy, and relaxation modes are determined in the cases of low-frequency sound and high-frequency sound. The difference in the nonlinear effects of sound in electrolyte and in a gas with excited vibrational degrees of molecules,...
-
Orthotropic membrane as a mechanical model of surgical implant in abdominal hernia repair
PublicationEven though the incisional hernia repair surgery is a well known procedure, mechanical properties of the tissue-implant system are unknown so the implantation of the repairing mesh is quite intuitive and, recurrences of the illness still take place. The main objective of the study is to define an operated hernia model that can be used for surgery planning and the assessment of the repair persistence. The load applied to the structure...
-
Mechanical compatibility of implants used in hernia repair with abdominal wall
PublicationThe paper deals with a membrane model of a synthetic surgical mesh for treatment of abdominal hernia. The authors analyse the compatibility of two implant types with the human wall: Dualmesh Gore and Proceed. The finite element method is applied to simulate tjhe behavior of the proposed model. Due fact that recurrences are usually caused by connection failure, this study is focused on reaction forces in supports representing the...
-
Influence of steel brackets supporting crane runway girders structure on the stress distribution in the brackets
PublicationThe paper presents a numerical analysis of steel brackets supporting a double-span crane runway girders. The purpose of the study was to assess the new structural solution based on the stress distribution in the brackets. In order to simplify the connection, the bottom flange of the crane runway girder is based directly on the upper flange of the bracket. As a result, the support reaction is no longer applied in the plane of the...
-
Mechanics of mesh implanted into abdominal wall under repetitive load. Experimental and numerical study
PublicationThere are a number of papers discussing medical and mechanical aspects of ventral hernia management. Despite intensive work on the problem understanding, recurrences of the sickness still happen too often. For that reason new aspects of the problem must be considered. In this paper, a change in the abdominal implant’s stiffness is discussed, which is caused by cyclic loading. Such loading influence abdominal implant e.g. while...
-
Sphere Drive and Control System for Haptic Interaction With Physical, Virtual, and Augmented Reality
PublicationA system for haptic interaction with physical, virtual, and augmented realities, founded on drive and measurement elements (DMEs), is considered. The system consists of eight DME rolls equipped with linear actuators, able to measure their angular velocity, drive the sphere, and adjust downforce (pressing the roll against the sphere). Two modeling issues are addressed. Special effort is put in to compensate for various technical...
-
Problem of aggregation in dye-DNA interaction, calorimetry studies
PublicationNucleic acids are the biological target for many antimicrobial, antitumor and antiviral drugs. Ligand-DNA interactions can be classified into two major categories: 1. covalent binding, which can provide to intermolecular adducts, 2. physico-chemical interactions, which can be divided into intercalation (e.g. adriamycin) or groove binding (e.g. dystamycin). There are several methods to investigate interactions between drug and DNA....
-
Ionic liquids for nano- and microstructures preparation. Part 1: Properties and multifunctional role
PublicationIonic liquids (ILs) are a broad group of organic salts of varying structure and properties, used in energy conversion and storage, chemical analysis, separation processes, as well as in the preparation of particles in nano- and microscale. In material engineering, ionic liquids are applied to synthesize mainly metal nanoparticles and 3D semiconductor microparticles. They could generally serve as a structuring agent or as a reaction...
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublicationThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...
-
Chitosan-coated coconut shell composite: A solution for treatment of Cr(III)-contaminated tannery wastewater
PublicationTannery industry generates a large amount of Cr(III)-contaminated wastewater daily. Unless properly treated, not only this effluent contaminates the water body, but also damages the environment and threatens public health. This batch study investigates the feasibility of chitosan-coated coconut shells as a low-cost material for removing Cr(III) from tannery wastewater. Both chitosan and coconut shell (CS) waste are abundantly available...
-
Biomechanical causes for failure of the Physiomesh/Securestrap system
PublicationThis study investigates the mechanical behavior of the Physiomesh/Securestrap system, a hernia repair system used for IPOM procedures associated with high failure rates. The study involved conducting mechanical experiments and numerical simulations to investigate the mechanical behavior of the Physiomesh/Securestrap system under pressure load. Uniaxial tension tests were conducted to determine the elasticity modulus of the Physiomesh...
-
STANY NIEUSTALONE TOWARZYSZĄCE POMIAROWI IMPEDANCJI PĘTLI ZWARCIA W OBWODACH WYJŚCIOWYCH ZASILACZY BEZPRZERWOWYCH UPS
PublicationW pracy przedstawiono metodykę i wyniki pomiarów stanów nieustalonych w zasilaczu bezprzerwowym (UPS) typu on - line. Do rejestracji zdarzeń po stronie zasilania i na wyjściu UPS wykorzystano dwa przyrządy do pomiaru jakości energii elektrycznej zsynchronizowane czasowo. Rejestratory kompresują uzyskane dane pomiarowe, co może wprowadzać dodatkowe błędy pomiaru wielkości mierzonych – napięć i prądów. Dodatkowe rejestracje oscyloskopem...
-
Truss imperfections in the design of bar and diaphragm bracing systems
PublicationIn the article three variants of roof bracing were considered: bar bracing, diaphragm bracing and the combination of bar and diaphragm bracing. Different analytical and numerical ways of taking into account the imperfections of the truss girder were compared. The entire 3D model of the roof (shell and beam elements with the eccentricities taken into account) was analysed numerically. Selected stressed-skin aspects were considered....
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublicationThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Selected aspects of the evolution of the industry analysis
PublicationPorter's five forces is a significant tool of analysis of industries. It helps evaluating variables of industry profitability and assessing firm performance. Using the framework, managers can take a decision as to which industries they can effectively compete in and position their companies to reduce the adverse effects of the mentioned forces. According to the critics, the five forces model is limited to its static nature. The...
-
Novel analysis methods of dynamic properties for vehicle pantographs
PublicationTransmission of electrical energy from a catenary system to traction units must be safe and reliable especially for high speed trains. Modern pantographs have to meet these requirements. Pantographs are subjected to several forces acting on their structural elements. These forces come from pantograph drive, inertia forces, aerodynamic effects, vibration of traction units etc. Modern approach to static and dynamic analysis should...
-
The Method of reduction of aerodynamic forces generated in turbine blade seals
PublicationThe distibution of pressure in the seal gaps does not only affect the so called '' leakage losses'' and the turbine stage overall efficiency but also plays an important role in the generation of aerodynamic forces which may cause self-excited rotor vibrations. The paper describes a chamber seal applied for the reduction of the aerodynamic forces created in shroud seals. This kind of turbine seal was patented and tested.
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublicationMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
Analysis of balancing of four stroke V6 engines
PublicationAnalysis of balance of V6 engines with a common-pin crankshaft depending on a cylinder bank angle and the crank radius to connecting rod length ratios , based on the relations derived, is presented in the paper. The bank angles providing the lowest moment of inertia forces in reciprocating motion, for selected values, were determined. The position of the plane of the main counterweights in order to maximum balance of the moment...
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Explanation of Reduction of Pressure Forces in Turbine Chamber Seals
PublicationThe paper describes a chamber seal reducing the aerodynamic forces created in shroud seals. Asymmetrical pressure distribution (due to rotor-stator eccentricity) in the blade tip clearance leads to the creation of pressure forces acting on the blade shroud. By increasing the volume above the shroud, the pressure distribution becomes more uniform on the whole shroud circumference and the effect of rotor eccentricity is reduced....
-
Is It Right To Predict Cutting Forces On The Basis Of Wood Density?
PublicationSeveral properties of wood can be correlated to wood density. It is widely accepted that the cutting power requirements are following this general assumption. Therefore, according to classic literature sources available for determination of the cutting power for both band- and circular- sawing machines, the cutting power requirements (and/or cutting forces) are computed as a function of the wood specific gravity SG. It was shown...
-
Deformation of an elastic second gradient spherical body under equatorial line density of dead forces
PublicationWe consider deformations of an elastic body having initially a spherical shape. Assumed deformation energy depends on the first and second gradient of displacements. We apply an equatorial line density of dead loads, that are forces per unit line length directed in radial direction and applied along the equator of the sphere. We restrict ourselves our analysis to the case of linearized second strain gradient isotropic elasticity...
-
Analysis of muscles behaviour. Part II. The computational model of muscles group acting on the elbow joint
PublicationThe purpose of this paper is to present the computational model of muscles' group describing the movements of flexion/extension at the elbow joint in the sagittal plane of the body when the forearm is being kept in the fixed state of supination/pronation. The method ofevaluating the muscle forces is discussed in detail. This method is the basis for the quantitative and qualitative verification of the proposed computational model...
-
Rotordynamic characteristics of a chamber seal
PublicationThe paper presents the results of numerical and experimental investigations into pressure forces generated in a turbine labyrinth seal of a modernized type. The experiments were performed on a single-stage air model turbine of the impulse type. The experiments were performed on a single-stage air model turbine of the impulse type. The experimental data were compared with theoretical results obtained by means of CFD Fluent Code....
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
An Intergrated Model of Motion, Steering, Positioning and Stabilization of an Unmanned Autonomous Maritime Vehicle
PublicationIn the paper the aim of an interdisciplinary research is presented. The research method is introduced. An object the unmanned autonomous maritime vehicle is briefly described. The key research problem concerns a combined model of the vehicle motion including the loads of lift and hydrodynamic nature. The model takes into account the gravity and displacement forces, resistance and thrust forces, lift and other hydrodynamic forces....
-
Thermal Buckling Analysis of Circular Bilayer Graphene sheets Resting on an Elastic Matrix Based on Nonlocal Continuum Mechanics
PublicationIn this article, the thermal buckling behavior of orthotropic circular bilayer graphene sheets embedded in the Winkler–Pasternak elastic medium is scrutinized. Using the nonlocal elasticity theory, the bilayer graphene sheets are modeled as a nonlocal double–layered plate that contains small scale effects and van der Waals (vdW) interaction forces. The vdW interaction forces between the layers are simulated as a set of linear springs...
-
Electroelastic biaxial compression of nanoplates considering piezoelectric effects
PublicationIn the present theoretical work, it is assumed that a piezoelectric nanoplate is connected to the voltage meter which voltages have resulted from deformation of the plate due to in-plane compressive forces whether they are critical buckling loads or arbitrary forces. In order to derive governing equations, a simplified four-variable shear deformation plate theory has been employed using Hamilton’s principle and Von-Kármán...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Analysis of compressive forces in CFGFT cylindrical pillars and their coatings using laboratory tests and metric spaces
PublicationThe article discusses compressive forces tests in composite-concrete pillars with the use of laboratory active experiment including the factors and properties of materials which have a significant impact on the test results and their repeatability. A polymer composite based on glass fiber reinforced resin with different fiber beam angles (20, 55 and 85) was used as a buffer/coat of the pole. Due to the problems with direct comparison...
-
Design of septic tanks placed on cohesive soils
PublicationThe paper presents a short review of literature with regard to design and erection of the reinforced concrete and concrete tanks. The authors investigated the underground septic tank with of 10 m3 capacity placed on cohesive soils. The authors compared the values of internal forces for soils in drained and undrained conditions with different geotechnical parameters: loamy sand of liquidity index IL = 0.1 and IL = 0.7 and clay with...
-
ANALYSIS OF THE PROJECT OF INNOVATIVE FLOATING TURBINE
PublicationThe design of a floating, innovative device for river water aeration and conversion of mechanical energy to electrical energy required the analysis of a number of geometrical and dynamic features. Such an analysis may be carried out on the basis of existing methods of numerical fluid mechanics. Models of pressures, forces and torques characteristic for the conversion of watercourse energy were developed for two basic concepts of...
-
SPECTRAL RESPONSE OF STATIONARY JACK-UP PLATFORMS LOADED BY SEA WAVES AND WIND USING PERTURBATION METHOD
PublicationThe paper addresses non-linear vibrations of offshore jack-up drilling platforms loaded by sea waves and wind in their stationary condition using the perturbation method. Non-linearity of dynamic equations of motion for fixed offshore platforms yields from two factors. The first is load excitation generating non-linear velocity coupling in a dynamic system. This coupling is inherent in the modified Morison equation, involving the...
-
Adaptive dynamic control allocation for over-actuated dynamic positioning system based on backstepping method in case of thruster faults
PublicationThe objective of the research considered in this paper is dynamic positioning of a nonlinear over-actuated marine vessel in the presence of limited information about thruster forces. First, the adaptive backstepping method is used to estimate the input matrix which will compensate partial loss of actuator effectiveness in the presence of actuator dynamics. Then, the adaptive commanded virtual forces and moment are allocated into...
-
Mechanical behaviour of the implant used in human hernia repair under physiological loads
PublicationIn laparoscopic operations of abdominal hernias some recurrences still take place, even when applying a surgical mesh. This is usually caused by a failure of the connection between the tissue and the implant. The study deals with the influence of an implant’s orientation on forces in joints, which connect the mesh to human tissues. In the paper, the implant is modelled as a membrane structure within framework of the Finite Element...
-
Application of Fracture Mechanics for Energetic Effects Predictions While Wood Sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (or power - more interesting from energetic point of view) could be considered from a point of view of modern fracture mechanics. Cutting...
-
SAWING PROCESS AS A NEW ALTERNATIVE WAY OF DETERMINING SOME WOOD PROPERTIES
PublicationCutting forces (power) could be considered from a point of view of modern fracture mechanics. The developed cutting model, derived from fracture mechanics, includes work of separation (fracture toughness) in addition to plasticity and friction, and also dullness of the cutting edge described by the cutting edge radius. Moreover, forecasting of the shear plane angle for the cutting models, broaden possibilities of energetic effects...
-
Verification of punching shear outside the shear cap by the direct method
PublicationThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Development and validation of lumbar spine finite element model
PublicationThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
An Innovative Approach to the Forecasting of Energetic Effects While Wood Sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specifi c cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, the cutting forces (power) problem may be tackled with an innovative, up-to-date fundamental analysis of the mechanics of sawing based on modern fracture mechanics....
-
An innovative approach to the forecasting of energetic effects while wood sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, the cutting forces (power) problem may be tackled with an innovative, up-to-date fundamental analysis of the mechanics of sawing based on modern fracture...
-
Behaviour of Colliding Multi-Storey Buildings under Earthquake Excitation Considering Soil-Structure Interaction
PublicationThis paper investigates the coupled effect of the supporting soil flexibility and pounding between neighbouring, insufficiently separated buildings under earthquake excitation. Two adjacent three-storey structures, modelled as inelastic lumped mass systems with different structural characteristics, have been considered in the study. The models have been excited using the time history of the Kobe earthquake of 1995. A nonlinear...
-
DESIGN AND STRENGTH CALCULATIONS OF THE TRIPOD SUPPORT STRUCTURE FOR OFFSHORE POWER PLANT
PublicationThe support structure being the object of the analysis presented in the article is Tripod. According to the adopted assumptions, it is a foundation gravitationally set in the water region of 60 m in depth, not fixed to the seabed, which can be used for installing a 7MW wind turbine. Due to the lack of substantial information on designing and strength calculations of such types of structures in the world literature, authors have...
-
The differential impact of a density of Polish pine wood on cutting forces with its origin region taken into consideration
PublicationIn the article the dependence of cutting forces in a function the density of wood with regard to the wood origin are presented. Samples used in experiment were with Scotch pine (Pinus sylvestris L.) originating from four provenances in Poland (Figure 1). Wood density was measured by two methods: stereometric method (global density) and radiometric method (local density). Stereometric method consists in measurements the volume...
-
An influence of the ship's block coefficient implementation on the evaluation of it's hull girder bending
PublicationAn influence of the three different ways of implementation ship's block coefficient δ (three geometrical models) on the stresses due to wave bending moment have been investigated. Two models have been applied and compared: beam one (description of the shape usingparameters) and FEM shell model (direct representation of the shape). The outcomes have been compared to Polish Register of Shipping (PRS) rules. The results show that...
-
AN INNOVATIVE APPROACH TO PREDICTION ENERGETIC EFFECTS OF WOOD CUTTING PROCESS WITH CIRCULAR-SAW BLADES
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. The aim of the paper is to present a new calculating model using the application of modern fracture mechanics and to compare cutting parameters of native beech, Bendywood...
-
Shell model of multiple-row moment I-section end-plate joint
PublicationThe paper deals with a problem of application of shell elements in the models of multiple-row moment end-plate connections. The extended connection of I-section with a cross-section W760x265x220 made of steel S355 was analyzed. Comparison analysis of FEM, complex volume and shell models has been done. Three cases with different end-plate thickness: 14, 18 and 36 mm were analyzed and compared with the reference results. Comparison...