Search
Filters
total: 246
filtered: 223
-
Catalog
Chosen catalog filters
Search results for: hydraulic resistance
-
Hydraulic resistance analyses of selected elements of the prototype Stirling engine
PublicationThe paper presents the results of simulation tests of hydraulic resistance and temperature distribution of the prototype Stirling alpha engine supplied with waste heat. The following elements were analyzed: heater, regenerator and cooler. The engine uses compressed air as a working gas. Analyses were carried out for three working pressure values and different engine speeds. The work was carried out in order to optimize the configuration...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Thermal-Hydraulic Studies on the Shell-and-Tube Heat Exchanger with Minijets
PublicationIn this paper a patented design of a heat exchanger with minijets, with a cylindrical construction is presented. It is followed by the results of its systematic experimental investigations in the single-phase convection heat transfer mode. Based on these results, validation of selected correlations (coming from the literature) describing the Nusselt number was carried out. An assessment of the heat exchange intensification level...
-
Wpływ strat mechanicznych w siłowniku teleskopowym zespołu zagęszczającego w pojeździe do usuwania odpadów z pojemników na skuteczność prasowania odpadów
PublicationHydraulic telescopic cylinders are used to power the moving wall of rear loader garbage trucks equipped with the traditional "sweep and slide" system. As the garbage compression force is directly dependent on the resistance force of the moving wall, losses in the hydraulic telescopic cylinder influence the compaction process. Taking them into account in the control system may improve the operation of the compaction...
-
Mechanical Properties of a Dike Formed from a Soil-ash Composite
PublicationThe paper presents the research results on application of composite soils for dike construction. The composite soil is produced by mixing bottom ash (by-product of energetics) with dredged material (sand) taken from the mouth of The Vistula river. The optimum composite for dike core was chosen with respect to mechanical parameters: high internal friction angle, good compaction and reduced hydraulic conductivity. The test dike was...
-
Experimental study on the seepage flow through the ice jam
PublicationIn light of the observed climate change, there is a need for better understanding of river ice processes for managing water resources in the cold regions. Ice jams produce significant resistance which may cause rise of water level and flooding. The jam resistance is only referred to the roughness of its underside, and this approach lead to exceptional roughness coefficients which has no physical explanation. Number of evidences...
-
Hydrauliczna wiarygodność wyników pomiarów terenowych stosowanych do identyfikacji oporności hydraulicznej przewymiarowanych sieci wodociągowych
PublicationPublikacja zawiera zalecenia metodyczne dotyczące identyfikacji oporności hydraulicznej w przewymiarowanych sieciach wodociągowych na tle spotykanych nieprawidłowości. Krytycznie oceniono wyniki pomiarów terenowych, które zastosowano do tarowania komputerowych modeli przepływów (KMP) pomimo, że nie spełniały kryterium hydraulicznej wiarygodności. Ponadto zaproponowano spadek hydrauliczny jako obiektywny wskaźnik wiarygodności pomiarów,...
-
Recycling of Industrial Waste as Soil Binding Additives—Effects on Soil Mechanical and Hydraulic Properties during Its Stabilisation before Road Construction
PublicationTo improve the in situ soil stabilization, different chemical additives are used (ion exchange compounds, additives based on H2SO4 or vinyl polymers, and organic additives using lignosul- fonates). One interesting alternative is the production of additives from various waste materials. The extensive testing of waste-based blends with soil was performed; the mechanical (unconfined compressive strength (UCS)) and hydraulic (capillary...
-
Przygotowanie, realizacja i ocena pomiarów terenowych do identyfikacji oporności hydraulicznej sieci wodociągowej
PublicationW procesie tworzenia komputerowego modelu przepływów (KMP) jednym z wiodących zadań jest przygotowanie i realizacja pomiarów terenowych w celu identyfikacji oporności hydraulicznej czynnej sieci wodociągowej. Motywacją autora do przedstawienia zasad postępowania w tym zakresie jest narastająca niefrasobliwość twórców KMP, którzy w nieuprawniony sposób używają paramodeli do rozwiązywania problemów inżynierskich. W pracy zdefiniowano...
-
Innovative Implantable Left Ventricular Assist Device—Performance under Various Resistances and Operating Frequency Conditions
PublicationThis paper presents the operation of an innovative left ventricular assist device under various resistances and operating frequencies. The operating principle of the device is based on pulsatile blood flow, which is forced by a suction–discharge device pumping helium into a set of intra-cardiac balloons. In this way, the ejection fraction of the left ventricle is increased, and the mitral valve is additionally occluded. What is...
-
The Application of Granulated Expanded Glass Aggregate with Cement Grout as an Alternative Solution for Sub-Grade and Frost-Protection Sub-Base Layer in Road Construction
PublicationThe purpose of the research was to assess the possibility of using granulated expanded glass aggregate (GEGA) with cement grout as a replacement of a sub-grade and frost-protection layer, made of natural fine aggregates (NATU), stabilized with a hydraulic binder. Instead of traditional parts of the road construction, such as the sub-grade and frost-protection layer with the application of fine aggregate, stabilized with cement,...
-
Przykłady realizacji i interpretacji wyników sondażowych pomiarów terenowych w czynnych systemach dystrybucji wody
PublicationW pracy przedstawiono przebieg realizacji i rezultaty sondażowych pomiarów terenowych w trzech układach dystrybucji wody o zróżnicowanym przewymiarowaniu sieci wodociągowej. Pomiary przeprowadzono w dążeniu do identyfikacji właściwości (cech) strukturalnych i funkcjonalnych układów po wieloletniej ich eksploatacji. Ustalenia te determinują opracowanie programu realizacji pomiarów dla potrzeb tarowania komputerowego modelu przepływu...
-
Evaluation of the stiffness modulus and phase angle of cold in-place recycled mix-tures for long curing periods
PublicationArticle presents the changes inbehaviour of cold-in place recycling mixtures made using cement and bituminous emulsion (CIR mixtures) after anelongated time of curing. Most of the available literatureregarding change instiffness modulus and phase angle presents resultsfor a maximum of several dozen days,which makesit difficult to predict the behaviour over the whole life of the compacted layer. The article...
-
Review and evaluation of cold recycling with bitumen emulsion and cement for rehabilitation of old pavements
PublicationThe article presents Polish experience with cold recycling of asphalt pavements with theusage of bituminous emulsion and cement. In the 1990s numerous roads in Polandrequired immediate reinforcement due to their significant degradation. Implementation ofthe cold recycling technology was one of the solutions to this problem. Cold recycledmixtures containebeside the recycled asphalt pavement and aggregateetwo differenttypes of binding...
-
Influence of type of material on performance of hydraulic components in thermal shock conditions
PublicationDuring the start-up of a hydraulic system in low ambient temperatures an incorrect operation may occur. The principles and conditions of safely operating hydraulic driven machines and devices are essential to designers and operators. For this reason the author of this article has conducted a series of tests on hydraulic components and systems in thermal shock conditions (cooled-down components were supplied with hot working medium)....
-
Losses and power balance in hydraulic satellite motor supplied with oil and HFA-E emulsion
PublicationMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motor with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motor. The research of satellite motor has been conducted...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Power balance in hydraulic satellite motors supplied with oil and HFA-E emulsion
PublicationMineral oil and HFA-E emulsion are liquids which differ in viscosity, density and lubricant properties. Therefore, supplying hydraulic satellite motors with these liquids, differences between quantity of hydraulic, volumetric and mechanical losses are observed. These losses influence efficiency of conversion of hydraulic energy into mechanical energy and thereby power balance of motors.
-
Suspended-sediment transport related to ice-cover conditions during cold and warm winters, Toudaoguai stretch of the Yellow River, Inner Mongolia, China
PublicationThe presence of winter ice in cold regions changes the water level, flow rate, velocity distribution, and other parameters of the river, which in turn affects the sediment concentration and channel evolution. Based on data obtained from Toudaoguai Hydrological Station from 1959 to 2021, this study examines the characteristics of the ice regime during cold and warm winters and the water and sediment transport processes along the...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
The influence of pressure drop on the working volume of a hydraulic motor
PublicationReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
Investigation method and mathematical model of pressure losses in hydraulic rotary motor
PublicationTis paper presents a way of determining the coefcient k of the pressure losses Δp (fow drag) in internal ducts 8 Mp of SWSB-63 hydraulic motor. Te coefcient is determined at a fow rate equal to the theoretical capacity Q of the Pt pump feeding the motor , the losses are related to the nominal pressure p in the hydraulic system. Te investigations n followed a model of energy performance of hydraulic rotary motor, proposed by...
-
Validation of Hydraulic Mechanism during Blowout Trauma of Human Orbit Depending on the Method of Load Application
PublicationThe more we know about mechanisms of the human orbital blowout type of trauma, the better we will be able to prevent them in the future. As long as the buckling mechanism’s veracity is not in doubt, the hydraulic mechanism is not based on equally strong premises. To investigate the correctness of the hydraulic mechanism’s theory, two different methods of implementation of the hydraulic load to the finite element method (FEM) model...
-
An innovative method of measuring the extension of the piston rod in hydraulic cylinders, especially large ones used in the shipbuilding and offshore industry
PublicationThe article presents the results of selected works related to the wider subject of research conducted at the Faculty of Mechanical Engineering and Shipbuilding at the Gdańsk University of Technology, regarding designing various on board devices with hydraulic drive for ships and other offshore facilities. One of the commonly used these mechanisms are hydraulic actuators with the measurement of the piston rod extension. The issue...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
DIGITAL HYDRAULICS CIRCUIT BASED ON PWM FUNCTION FOR CONTROLLING HYDRAULIC ACTUATOR POSITION
PublicationHydraulic systems are used in many different industries, such as multi-source hydrostatic drive systems. In traditional hydraulic systems, a proportional servo valve is used to control the position of hydraulic actuators. The low energy efficiency and high cost of these control valves are two major problems with these systems. Digital hydraulics is one of the most unique ideas on how to solve these problems. Researchers like digital...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublicationThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Hydraulic equations for vortex separators dimensioning
PublicationThe paper presents a set of hydraulic expressions developed to design vortex separators. These devices are used for gravitational removal of suspensions from wastewater. Measurements and theoretical considerations allowed the authors to formulate a mathematically simple velocity field model. Than, equations describing particle motion in the separator were derived. Finally, a technical procedure for hydraulic design of vortex separators...
-
Problem of Clogging in Drainage Systems in the Examples of the Zur and Podgaje Dams
PublicationDrainage plays an extremely important role in hydraulic structures, such as earth dams. Observations of drainage in hydraulic structures under various soil conditions indicate that the phenomenon of clogging can lead to a radical reduction in the efficiency of drainage, making it non-functional within a few years after construction. This article describes the problems of drainage clogging by iron oxide in the examples of the Zur...
-
Research of hydrotronic variable displacement radial piston pump with electro -pneumatic control
PublicationThe paper presents the developed new electro-pneumatic control (pneumotronic) system for hydraulic fixed-displacement radial piston pump. Hydraulic fixed-displacement radial piston pump equipped with the proposed control system changes into hydrotronic variable-displacement radial piston pump. Pump flow rate control is realized by means of programmable logic controller, electro-pneumatic valves, pneumatic cylinders and a sensor.
-
The Methodology for Determining the Theoretical Based on the Characteristics of Effective Absorbency Versus Pressure Drop in the Motor
PublicationThis article describes a method for determining the theoretical and actual working volume of a hydraulic motor. It has been shown that the actual working volume of the motor is the sum of the theoretical working volume and the additional volume that depends on the pressure drop in the working chambers of the motor. It was also shown that the volumetric losses in the hydraulic motor are not only a function of the pressure drop in...
-
New Design of Axial Piston Pump with Displaced Swash Plate Axis of Rotation for Hydro-Mechanical Transmissions
PublicationThis paper presents a prototype design of an axial piston pump with displaced swash plate axis of rotation in two directions of discharge with electronic control intended for installation on a hydraulic-mechanical gearbox dedicated to working machines. The effect of displacement of the swash plate rotation axis on dead space volume and volumetric efficiency is presented. The construction and principle of operation of the capacity...
-
Shallow Water Equations as a Mathematical Model of Whitewater Course Hydrodynamics
PublicationPredicting the positions of local hydraulic phenomena, as well as accurately esti-mating the depth and velocity of the water flow are necessary to correctly config-ure a whitewater canoeing course. Currently, a laboratory and full 3D CFD model-ing are typically used in the design process to meet these needs. The article points to another possibility which can be useful at the preliminary stage of the design. The authors show that...
-
Perforating systems in shale gas recovery
PublicationHydraulic fracturing is common method of shale gas recovery. Due to environmental, economical and technological problems many alternative technologies have been developed. One of the most promising group of technologies is based on perforating systems. This paper describes theoretical and practical aspects of best known technologies used to create perforations. New perforating/fracturing technologies which can replace hydraulic fracturing...
-
Methodology of experimental research on efficiency of hydro-mechanical automatic gearbox
PublicationThe article shortly describes the design and principle of operation of the hydromechanical gearbox and presents the methodology and design of test stands used for testing hydromechanical proto-type gearbox developed at Technical University of Gdansk. The article presents an approach according to which, in order to obtain reliable measurement data, it is necessary to separate the tests of the hydraulic and mechanical parts of the...
-
NEW CONCEPT OF HYBRID PROPULSION WITH HYDROSTATIC GEAR FOR INLAND WATER TRANSPORT
PublicationThe article presents the development of author’s concept of a diesel/hydraulic propulsion system for inland watercraft. Due to specific nature of vessel navigation on rivers, classical propulsion systems with shaft lines can be effectively replaced by systems with hydraulic power transmission. A solution is also presented of a hybrid design with extra electric port having the form of a pumping system driven from a battery of accumulators....
-
Hydraulic valve design methodology for hydro turbine control system
PublicationThe control of the turbine and its equipment in a hydroelectric power plant requires the HPU (hydraulic power unit) to deliver large volumes of working fluid in a short time at specific optimum control parameters. The use of typical proportional flow control valves created by manufacturers of hydraulic components in low-pressure control systems is disadvantageous due to high pressure losses in the control chambers. This paper presents...
-
Evaluation of losses in a hydraulic motor based on the SWSB - 63 motor tests
PublicationIn this paper are compared two models of energy losses: that suggested by Prof. Paszota,Z. in monograph "Energy losses in the hydraulic displacement motors - definitions and relations serving the evaluation of the efficiency of hydrostatic drive" [18] and that ofProf. Balawender, A. in "Energy analysis and methodology of testing of low-speed hydraulic motors" [1]. By using the data obtained from the tests of SWSB-63 hydraulic motors...
-
Mathematical model defining volumetric losses of hydraulic oil compression in a variable capacity displacement pump
PublicationThe objective of the work is to develop the capability of evaluating the volumetric losses of hydraulic oil compression in the working chambers of high pressure variable capacity displacement pump. Volumetric losses of oil compression must be determined as functions of the same parameters, which the volumetric losses due to leakage, resulting from the quality of design solution of the pump, are evaluated as dependent on and also...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublicationA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Numerical Analysis of Steady Gradually Varied Flow in Open Channel Networks with Hydraulic Structures
PublicationIn this paper, a method for numerical analysis of steady gradually varied fl ow in channel networks with hydraulic structures is considered. For this purpose, a boundary problem for the system of ordinary differential equations consisting of energy equation and mass conservation equations is formulated. The boundary problem is solved using fi nite difference technique which leads to the system of non-linear algebraic equations....
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublicationThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART IV) MODELLING THE HEATING PROCESS AND DETERMINING THE SERVICEABILITY OF HYDRAULIC COMPONENTS DURING THE STARTING-UP IN LOW AMBIENT TEMPERATURE
PublicationDesigners of hydraulically driven machines and devices are obliged to ensure during design process their high service life with taking into account their operational conditions. Some of the machines may be started in low ambient temperature and even in thermal shock conditions (due to delivering hot working medium to cold components). In order to put such devices into operation appropriate investigations, including experimental...
-
Residence time distribution in rapid multiphase reactors
PublicationResidence time distribution (RTD) provides information about average hydraulic residence time and the distribution of material in the reactor. A method for determining RTD for reactors with very short hydraulic residence times is deconvolution based on extraction of real RTD by the analysis of a non-ideal input signal. The mean residence time and dispersion were determined for the spinning fluids reactor (SFR). For the first time...
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
The methodology of design of axial clearances compensation unit in hydraulic satellite displacement machine and their experimental verification
PublicationA new methodology of calculating the dimensions of the axial clearance compensation unit in the hydraulic satellite displacement machine is described in this paper. The methods of shaping the compensation unit were also proposed and described. These methods were used to calculate the geometrical dimensions of the compensation field in an innovative prototype of a satellite hydraulic motor. This motor is characterized by the fact...
-
Safety of erection and repair of steel tanks with geometric imperfections using heavylift jack-up system
PublicationSafety analysis is performed of cylindrical vertical steel tanks during erection using heavylift jack up system. During an assembly or repair process a set of hydraulic supports is used. It allows to use the in-place lifting of heavy steel constructions on the required height. Wind can strongly influence stability of the lifted tank. Any geometric imperfections can reduce the critical or limit load. In the work failures of the...
-
Method of sum of power losses as a way for determining the ki coefficients of energy losses in hydraulic motor
PublicationThis paper shows application of the method of sum of power losses to determining energy losses which occur in hydraulic rotary motor in situation when not all laboratory data are at one’s disposal or when no use is made of data contained in catalogue charts. The method makes it possible to determine the coefficients ,ki , of energy losses occurring in the motor. The method of sum of power losses is based on the approach proposed...
-
COMPUTER ANALYSIS OF HYDRAULIC CONDITIONS IN A SANITARY CHAMBER
PublicationThis paper presents analysis of hydraulic conditions of sewage flow down the slipway (ramp) in the collecting sanitary chamber connecting 3 collectors on the inlet: ⌀600, ⌀800 and ⌀1400 and one on the outlet ⌀1600 mm, with a maximum difference of elevation 5 m. The mathematical model has been made and hydraulic calculations were carried out in steady flow conditions. Then wastewater surface elevation, energy grade line elevation,...
-
Hydraulic potential of the Lower Vistula (Poland)
PublicationThe Vistula is the largest river in Poland. Lower Vistula (part of the river discussed in this paper) is almost four hundred kilometers long river section extending from the tributary Narew to the outflow to the Baltic Sea. In the 17th century the Vistula was the most navigable river in Europe. After partitioning of Poland the Vistula lost its significance. Now the Lower Vistula should provide a navigation connection to the Europe...