Filters
total: 739
filtered: 533
-
Catalog
Chosen catalog filters
Search results for: POWER ENGINEERING
-
Diagnosis of Damage in a Steel Tank Model by Shaking Table Harmonic Tests
PublicationThe aim of the present paper is to show the results of the shaking table experimental study concerning the diagnosis of damage in a model of cylindrical steel tank with self-supported roof which is filled with liquid. During the tests, the base of the structure was excited under the harmonic loading with variable frequency. The tests were repeated for different stages of damage, which was introduced in the model by easing the bolts...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Verification of safety in low-voltage power systems without nuisance tripping of residual current devices
PublicationLow-voltage power systems require initial and periodical verification to check the effectiveness of protection against electric shock. As a protection in case of fault, automatic disconnection of supply is most often used. To verify such a protection measure, the earth fault loop impedance or resistance is measured. This measurement is easy to perform in circuits without residual current devices. When residual current devices are...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublicationA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
THREE-LEVEL F-TYPE INVERTER
PublicationGiven the recent available IGBT switch modules up to 6.5 kV, 1200 A rating, the prospect of the diode-free variant topology of the three-level neutral-point-clamped (3-level, T-type) inverter in certain medium voltage applications is bright; due to its small part count and low conduction losses compared to the diode-clamped NPC inverter. However, within this voltage range, the input dc voltage rating of 50% of the switches per...
-
Modified Preisach model of hysteresis in multi air gap ferrite core medium frequency transformer
PublicationThis article presents the modified Preisach model of hysteresis for a 3-phase medium frequency transformer in a 100 kW dual active bridge converter. The transformer magnetic core is assembled out of ferrite I-cores, which results in multiple parasitic air gaps. For this transformer, the hysteresis loops were measured and parameters of the Preisach model were determined. The Preisach distribution function is approximated with a...
-
Structure and the space vector modulation for a medium-voltage power-electronic-transformer based on two seven-level cascade H-bridge inverters
PublicationThis study presents the structure and the space vector pulse-width modulation (SVPWM) for power electronic transformer (PET) based on two seven-level cascade H-bridge (CHB) inverters. The DC links of CHB inverters are coupled with nine dual-active bridge (DAB) converters with medium-frequency transformers. The DC-link voltages are equalised with two methods – through the control of DAB voltages...
-
Lagrangian model of an isolated dc-dc converter with a 3-phase medium frequency transformer accounting magnetic cross saturation
PublicationThis article presents a nonlinear equivalent circuit model of an isolated dc-dc converter with a 3-phase medium frequency transformer. The model takes into account the magnetic cross saturation of the 3-phase core-type magnetic circuit. The model is suitable in detailed electromagnetic transient simulations of power systems involving isolated dc-dc converters. The model is developed using the Lagrange energy method. It involves...
-
Overview of DC–DC Converters Dedicated to HVdc Grids
Publication -
Estimation of Parameters Associated With Individual Sources of Voltage Fluctuations
Publication -
The Wiener filter applied to EMI decomposition
PublicationArtykuł przestawia zastosowanie metody filtracji Wienera do dekompozycji zaburzeń elektromagnetycznych z różnych źródeł. Zaburzenia generowane w trójfazowym rezonansowym falowniku napięcia typy PQRDCLI oraz w przekształtniku napięcia stałego zasilającego obwód sterowania falownika zostały zmierzone z zastosowaniem sieci sztucznej (LISN). W oparciu o transmitancje częstotliwościowe pomiędzy źródłami zaburzeń i zaburzeniami zmierzonymi...
-
AC Microgrid Control and Management Strategies: Evaluation and Review
Publication -
Hybridized SVPWM Algorithm for Multilevel CHB Inverter With DC-Link Voltage Control Capability
PublicationThe deployment of a space vector pulsewidth modulation (SVPWM) scheme in controlling cascaded H-bridge multilevel inverter (CHB MLI) is quite challenging; especially, when a substantial number of output voltage levels are involved and the dc-link voltages are out of balance. In this article, a simple SVPWM algorithm for CHB MLI is proposed. In the proposed algorithm, all the H-bridges in an inverter phase are treated as a single...
-
Automated network control and supervision
PublicationPrzedstawiono ogólne problemy związane z postępem w zakresie integracji systemów informatycznych w elektroenergetyce. Podano zasady budowy struktury systemów sterowania i nadzoru.
-
Optimal linear control theory in power system application
PublicationPrzedstawiono syntezę stabilizatora systemowego przy wykorzystaniu metodyki Hinf. Zaprojektowany regulator umożliwia uzyskanie lepszych rezultatów w porównaniu z regulatorem odniesienia w szerokim zakresie zmian punktu pracy.
-
Problems of exact generation ofinverter output voltage
PublicationW pracy przedstawiono nową modyfikację modulatora szerokości impulsów. Rozważono problemy generacji dokładnej wartości napięcia wyjściowego falownika. Zaproponowano dwie metody generacji małej wartości napięcia.
-
Power control system structure of doubly‐fed induction generator connected to current source converter
PublicationThe power control system structures for a doubly-fed generator (DFIG) are proposed. The classical field oriented control and the feedback control with the multi-scalar variables were considered. The generator is working in the AC grid connection mode. The rotor side of the generator is connected to the current source converter (CSC); the stator is directly related to the AC grid. The static feedback linearization using the multi-scalar...
-
Supervisory control of wind farm
PublicationW artykule przedstawiono układ nadrzędnej regulacji farmy wiatrowej umożliwiający minimalizację wahań mocy czynnej na wyjściu farmy wiatrowej.
-
Control Strategy of a Five-Phase Induction Machine Supplied by the Current Source Inverter With the Third Harmonic Injection
PublicationIn the five-phase induction machine (IM), it is possible to better use the electromagnetic circuit than in the three-phase IM. This requires the use of an adequate converter system which will be supplied by an induction machine. The electric drive system described, in this article, includes the five-phase induction machine supplied by the current source inverter (CSI). The proposed novelty—not presented previously—is the control...
-
EMI mitigation of GaN power inverter leg by local shielding techniques
PublicationThis paper presents local shielding techniques applied to a half-bridge inverter leg with the aim to reduce the common mode (CM) current noise at converter’s DC input. The research study is conducted for 650V Enhancement mode Gallium Nitride (GaN) power transistor switches. Main contributors of parasitic capacitances referred to the inverter-leg middle point node are identified. Then, shielding solutions are proposed to reduce...
-
Hybridized Space-Vector Pulsewidth Modulation for Multiphase Two-Level Voltage Source Inverter
PublicationIn space vector pulsewidth modulation (SVPWM) algorithms for multiphase two-level voltage source inverters (VSI), the components of active vectors in all orthogonal spaces have to be calculated within the processor and stored in its memory. These necessitate intensive computational efforts of the processor and large memory space. This article presents a hybridized SVPWM for multiphase two-level VSI. In this algorithm, elements...
-
Medium-Voltage Drives: Challenges and existing technology
PublicationThe article presents an overview of state-of-art solutions, advances, and design and research trends in medium-voltage (MV) drive technologies - and also discusses the challenges and requirements associated with the use of such drives. The choice and deployment of MV drives in industries are associated with numerous requirements related to the front-end converter (grid side) and inverter (machine side). The focus is on solutions...
-
Energy recovery effectiveness in trolleybus transport
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest whichis connected both with a growth in environmental awareness of the society and an increase in the pricesof fuel and electricity. One of the possibilities to reduce energy consumption in urban public transport isto increase the extent of regenerative braking energy utilization. This can be achieved by its accumulationin the supercapacitors...
-
A simplified behavioral MOSFET model based on parameters extraction for circuit simulations.
PublicationThe paper presents results on behavior modeling of general purpose Metal-Oxide Semiconductor Field-Effect Transistor (MOSFET) for simulation of power electronics systems requiring accuracy both in steady-state and in switching conditions. Methods of parameters extraction including nonlinearity of parasitic capacitances and steady-state characteristics are based on manufacturer data sheet and externally measurable characteristics....
-
Modelling of steady state and transient performance of the synchronous generator considering harmonic distortions caused by non-uniform saturation of the pole shoe
PublicationIn this paper a synchronous generator model is described. This model is developed on the assumption that in loaded and no load conditions the saturation effect affects the pole shoe in a different way. The developed model is based on the multiple saliency model and is formulated using winding function approach in machine variables. The influence of the non-uniform saturation of the pole shoe in load conditions on the performance...
-
Earth wires currents calculation by tableau analysis
PublicationThe paper presents a new method to compute a phase-to-earth fault current distribution in overhead transmission line. The method is based on the tableau analysis of an unbalanced, multi-wire model of a transmission line. It allows for the calculation of current distribution in overhead earth wires along the transmission line. Additionally, it may be used to calculate currents in a tower’s earthing system as well as voltages over...
-
Errors of a Linear Current Approximation in High-Speed PMSM Drives
PublicationCurrent sampling techniques and predictive algorithms used in the digital control of electric drives rely on a simple mathematical model that assumes linear current changes upon constant supplying voltages. This paper identifies rotor movement as a factor that makes this assumption invalid when the rotor covers an angular distance of a few tens of degrees during the control interval duration. The errors of the linear current approximation...
-
Comparison of Impedance-Source Networks for Two and Multilevel Buck–Boost Inverter Applications
Publicationmpedance-source networks are an increasingly popular solution in power converter applications, especially in single-stage buck-boost power conversion to avoid additional front-end dc-dc power converters. In the survey papers published, no analytical comparisons of different topologies have been described, which makes it difficult to choose the best option. Thus, the aim of this paper is to present a comprehensive analytical comparison...
-
Novel Family of Single-Phase Modified Impedance-Source Buck-Boost Multilevel Inverters With Reduced Switch Count
Publicationhis paper describes novel single-phase solutions with increased inverter voltage levels derived by means of a nonstandard inverter configuration and impedance source networks. Operation principles based on special modulation techniques are presented. Detailed component design guidelines along with simulation and experimental verification are also provided. Possible application fields are discussed, as well as advantages and disadvantages....
-
Conducted EMI Propagation Paths in DC-AC Hard Switching Converter
PublicationIn order to limit the electromagnetic interference (EMI) in power electronics devices, knowledge about the phenomena connected with EMI generation and propagation is necessary. This papers describes the propagation paths in the 3 phase voltage source inverter using wide-band simulation and laboratory test with the signal processing method Wiener filtering, where the transfer functions between voltage across switches and the perturbation...
-
Geometrically nonlinear FEM analysis of FGM shells based on neutral physical surface approach in 6-parameter shell theory
PublicationThe paper presents the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter being the drilling degree of freedom. The material law is derived by through-the-thickness integration of the Cosserat plane stress equations. The constitutive equations are formulated with respect to the neutral physical surface. The influence of...
-
Design of Intelligent Low-Voltage Load Switch for Remote Control System in Smart Grid
PublicationCurrent low-voltage load switches do not support remote disconnect/connect and real-time monitoring of a disconnect/connect state. Addressing to these issues, this paper presents a low-voltage load switch for a smart remote control system, which uses a one-chip microcontroller board and a DC step motor drive mechanism and provides the feedback on the switch status also. Arrears disconnect and full-pay connect control is implemented...
-
M-integral for finite anti-plane shear of a nonlinear elastic matrix with rigid inclusions
PublicationThe path-independent M-integral plays an important role in analysis of solids with inhomogeneities. However, the available applications are almost limited to linear-elastic or physically non-linear power law type materials under the assumption of infinitesimal strains. In this paper we formulate the M-integral for a class of hyperelastic solids undergoing finite anti-plane shear deformation. As an application we consider the problem...
-
Assembling and testing of quasi-static hybrid piezoelectric motor based on electroactive lubrication principle
PublicationThe presented paper concerns a novel concept of hybrid piezoelectric motor based on electroactive lubrication principle. Its structure is combined of quasi-static and resonance piezoelectric actuators, synchronizing their work to generate the rotary movement. The hybrid motor topology is compared to the existing piezoelectric motors, regarding its field of applications in embedded systems with very high security requirements. The...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublicationThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Numerical Study of Turbulent Flow and Heat Transfer of Nanofluids in Pipes
PublicationIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Variable-fidelity shape optimization of dual-rotor wind turbines
PublicationPurpose Dual-rotor wind turbines (DRWTs) are a novel type of wind turbines that can capture more power than their single-rotor counterparts. Because their surrounding flow fields are complex, evaluating a DRWT design requires accurate predictive simulations, which incur high computational costs. Currently, there does not exist a design optimization framework for DRWTs. Since the design optimization of DRWTs requires numerous model...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublicationThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
Design advantages and analysis of a novel five-phase doubly-fed induction generator
PublicationPurpose – The purpose of this paper is to provide an analysis of the performance of a new five-phase doubly fed induction generator (DFIG). Design/methodology/approach – This paper presents the results of a research work related to fivephase DFIG framing, including the development of an analytical model, FEM analysis as well as the results of laboratory tests of the prototype. The proposed behavioral level analytical model is based...
-
Support for argument structures review and assessment
PublicationArgument structures are commonly used to develop and present cases for safety, security and for other properties of systems. Such structures tend to grow excessively, which causes problems with their review and assessment. Two issues are of particular interest: (1) systematic and explicit assessment of the compelling power of an argument, and (2) communication of the result of such an assessment to relevant recipients. The paper...
-
Frequency response spectra applied to assess efficiency of the training techniques
PublicationThe purpose of the research is to assess the increase of the muscle strength and power. Movement of the human body when the moving one impacts a stationary or moving body is taken under consideration. The waveform produced by an impact is transformed into frequency domain. The acceleration record is transformed as a complex spectrum, by the use of a Discrete Fourier Transformation. In this paper the applications of the discrete...
-
An experimental investigation on the effect of new continuous core-baffle geometry on the mixed convection heat transfer in shell and coil heat exchanger
PublicationIn the article, the authors presented the influence of continuous core-baffle geometry at mixed convection heat transfer in shell and coil heat exchanger. Experiments were carried out for a large power range, i.e. from 100W to 1200W and mass flow rates ranging from 0.01 kg/s to 0.025 kg/s. During the experiments, the mass flow rate of cooling water, the temperature of water at the inlet and outlet as well as the wall temperature...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublicationWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Analysis of the possibility of creep damage detection in T24 heat resistant steel with the help of magnetic nondestestructive testing methods
PublicationThe paper presents the result of an analysis of applicability of various electromagnetic methods of nondestructive evaluation for creep damage detection in a novel heat resistant steel - T24 grade. Two sample sets, cut out from membrane wall tubes, were investigated – the as-delivered one and another exploited for 36,000 h in a power plant. There are described results of magnetic hysteresis loops B(H), Barkhausen noise (BN) and...
-
Intensification of catechin extraction from the bark of Syzygium cumini using ultrasonication: Optimization, characterization, degradation analysis and kinetic studies
PublicationCatechin is a prominent polyphenolic component that possesses various medicinal properties. Present work communicates the intensification and optimization of catechin extraction from the bark of Syzygium cumini tree using stirred reactor, soxhlet, ultrasonic bath, and ultrasonic horn technique. The optimization of several parameters such as type of solvent, solid to solvent ratio (1:100 w/v), speed of agitation (300 RPM), extraction...
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publication -
A Comprehensive Review on DC Fast Charging Stations for Electric Vehicles: Standards, Power Conversion Technologies, Architectures, Energy Management, and Cybersecurity
PublicationThis paper aims to review the main research points regarding DC fast charging stations. At the beginning, the paper addresses an overview of DC fast charging standards, galvanic isolation, EV powertrain, and some examples of real DC fast chargers. This part highlights that DC fast chargers are usually connected to an AC network or microgrid, whereas DC microgrids would be a better choice to increase the charging efficiency and...
-
New insights on lithium storage in silicon oxycarbide/carbon composites: Impact of microstructure on electrochemical properties
PublicationIn this work, we study the impact of the preceramic precursor vinyltriethoxysilane (VTES) on the electrochemical performance of silicon oxycarbide (SiOC) glass/graphite composites. We apply an innovative approach based on high-power ultrasounds in order to obtain highly homogenous composites with a uniform distribution of small graphitic flakes. This procedure enhances gelation and drying of VTES-based preceramic polymer/graphite...
-
Machine-Learning Methods for Estimating Performance of Structural Concrete Members Reinforced with Fiber-Reinforced Polymers
PublicationIn recent years, fiber-reinforced polymers (FRP) in reinforced concrete (RC) members have gained significant attention due to their exceptional properties, including lightweight construction, high specific strength, and stiffness. These attributes have found application in structures, infrastructures, wind power equipment, and various advanced civil products. However, the production process and the extensive testing required for...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublicationThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...