Search
Filters
total: 564
filtered: 497
Search results for: ENERGY STORAGE AND CONVERSION DEVICES
-
Enhanced energy conversion as a result of fluid-solid interaction in micro- and nanoscale
PublicationIt is known that nano- and micromechanics require new approaches to right describing of surface-like phenomena which lead to an enhanced energy conversion. In this work, a general form of surface forces that consist of a contribution from both the friction and mobility components has been extended to collect the effects of bulk and surface motion of a fluid. Quite similar impact can be observed for a solid-fluid mixture, where...
-
Impact of R/X ratio of distribution network on selection and control of energy storage units
PublicationThe interest in energy storage is still increasing. Energy storage units are installed in high voltage networks, medium voltage networks and low voltage distribution networks as well. These units are often used to improve power quality. One of the criteria for improving power quality is reducing voltage deviations. Depending on the type of network and specifying its R/X ratio, this criterion can be fulfilled by control of active...
-
ENERGY SAVINGS BY APPLICATION OF SUPERCAPACITOR STORAGE IN TROLLEYBUS SUPPLYING STATION – ANALYSIS OF EXPERIMENTAL RESULTS
PublicationIn 2011–2013, stationary supercapacitor storage developed by the Electrotechnical Institute in Warsaw was put into trial operation in the trolleybus substation “Północna” (North) located in Gdynia. The article presents the results recorded during supercapacitor storage operation and discusses the impact of the storage on energy consumption savings. Guidelines for selecting a location for stationary supercapacitor storage...
-
Logistical Aspects of Energy Conversion Efficiency in Marine Steam Power Plants in Off-Design Conditions
PublicationThe paper presents logistical aspects of energy conversion efficiency in off-design conditions. The main part of the article is based on results of thermodynamic calculation for large propulsion steam turbine under partial loads. Calculations are made on extended mathematical model of two proposed steam turbine thermodynamic cycles using Stodola’s cone law. The conclusion based on calculation re-sults contains importance of off-design...
-
Phase change thermal energy storage – the experience of the materials preparation for the specific applications.
PublicationThermal energy storage and temperature stabilization is very important in many engineering applications. There are three kinds of thermal energy storage: sensible heat, latent heat and reversible chemical reaction heat. Phase change materials (PCM) absorb, store and release large amounts of energy in the form of latent heat, at constant temperature, called the transition temperature. Many innovative applications could be found...
-
Thermochemical Conversion of Biomass and Municipal Waste into Useful Energy Using Advanced HiTAG/HiTSG Technology
PublicationAn advanced thermal conversion system involving high-temperature gasification of biomass and municipal waste into biofuel, syngas or hydrogen-rich gas is presented in this paper. The decomposition of solid biomass and wastes by gasification is carried out experimentally with a modern and innovative regenerator and updraft continuous gasifier, among others. A ceramic high-cycle regenerator provides extra energy for the thermal conversion...
-
Hybrid energy storage forelectric multiple units to operate at the partially electrified line Gdynia -Hel
PublicationThe article presents calculations enabling the selection of an on-board energy storage device to replace diesel-powered trains with modern storage multiple units on the example railway line Gdynia Główna -Hel. The pioneering and currently used storage electric multiple units, mainly in Europe, were presented. The condensed results of the inventory of the line in question, including the technical condition...
-
Modular power converter with superconducting magnetic energy storage for electric power distribution system — Analysis and simulation
PublicationThis paper describes selected issues concerning realization of energy storage system (ESS) designed to operate in power distribution system. This paper presents a modular approach of 300 kVA power converter operating with superconducting magnetic energy storage (SMES), which gives high dynamics together with high power and suitable capability for instantaneous energy storage. Analysis and simulation studies of selected power converter...
-
A Model of Thermal Energy Storage According to the Convention of Bond Graphs (BG) and State Equations (SE)
PublicationThe main advantage of the use of the Bond Graphs method and State Equations for modeling energy systems with a complex structure (marine power plants, hybrid vehicles, etc.) is the ability to model the system components of different physical nature using identical theoretical basis. The paper presents a method of modeling thermal energy storage, which is in line with basic BG theory. Critical comments have been put forward concerning...
-
Nanomaterials for Environmental Purification and Energy Conversion
Publication -
Synthesis and characterization of MoS2-carbon based materials for enhanced energy storage applications
PublicationThe article delves into the synthesis and characterization of MoS2-carbon-based materials, holding promise for applications in supercapacitors and ion batteries. The synthesis process entails the preparation of MoS2 and its carbon hybrids through exfoliation, hydrothermal treatment, and subsequent pyrolysis. Various analytical techniques were employed to comprehensively examine the structural, compositional, and morphological properties...
-
Graphene and Its Derivatives for Energy Storage
Publication -
Techno-economic evaluation of combined cycle gas turbine and a diabatic compressed air energy storage integration concept
PublicationMore and more operational flexibility is required from conventional power plants due to the increasing share of weather-dependent renewable energy sources (RES) generation in the power system. One way to increase power plant’s flexibility is integrating it with energy storage. The energy storage facility can be used to minimize ramping or shutdowns and therefore should lower overall generating costs and CO2 emissions. In this article,...
-
Experimental and theoretical study of a vertical tube in shell storage unit with biodegradable PCM for low temperature thermal energy storage applications
PublicationThis article presents the experimental investigations of the coconut oil-based TES module for HVAC applications in the ambient and-sub ambient temperature range. To properly study this problem modular experimental module and test loop were developed. Special attention has been paid to study the physical mechanism of the melting/solidification process for natural substance (coconut oil) which has perspectives to be used in thermal...
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublicationThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
Onboard Energy Storage and Power Management Systems forAll-Electric Cargo Vessel Concept
PublicationThis paper presents an innovative approach to the design of a forthcoming, fully electric-powered cargo vessel. This work begins by defining problems that need to be solved when designingvessels of this kind. Using available literature and market research, a solution for the design of apower management system and a battery management system for a cargo vessel of up to 1504 TEUcapacity was developed. The proposed solution contains...
-
Heat transfer enhancement of modular thermal energy storage unit for reversible heat pump cooperation
PublicationThe following article presents experimental comparison research on a hexagonal shelland-tube latent thermal energy storage (TES). Such shape of a shell was deliberately chosen instead of a cylindrical one due to its high modularity and with intent for future applications in automobiles (EV and PHEV) air conditioning systems (HVAC). Two geometries of helical coils, acting as tubes, were studied in this article. One was a simple...
-
Modelling, thermography and digital processing of energy conversion processes
PublicationW pracy przedstawiono zagadnienia modelowania fizycznego i numerycznego procesów wymiany ciepła i konwersji energii. Do analizy wymiany ciepła w przestrzeni wypełnionej płynem zastosowano termografie krystaliczne i komputerowy system analizy otrzymanych laserowych obrazów. Wykonano również termogramy powierzchni pokrytych także ciekłokrystaliczniei jako przykład przeanalizowano rozkład temperatury na powierzchniach ciał stałych...
-
Analysis of the possibility of increasing thermal-electric energy conversion ratio in CHP units based on micro gas turbine
PublicationThe aim of this paper is to analyze the possibility of increasing thermal energy to electricity conversion efficiency in combined heat and power (CHP) units based on micro gas turbine during low heat demand periods. At the beginning sustainable development postulates under power engineering are explained. Next micro CHP as part of distributed generation idea is presented. The main part of the article is based on results of thermodynamic...
-
Effect of the let-through energy of overcurrent protective devices on the temperature of conductors during short-circuits
PublicationThe scope of the verification of low-voltage systems covers the earth fault loop impedance measurement. This measurement is usually performed with the use of low-value current meters, which force a current many times lower than the one occurring during a real short-circuit. Therefore, the international standard recommends consideration of the increase of resistance of conductors with the increase of temperature, which may occur...
-
Integrated algorithm for selecting the location and control of energy storage units to improve the voltage level in distribution grids
PublicationThis paper refers to the issue that mainly appears in distribution grids, where renewable energy sources (RES) are widely installed. In such grids, one of the main problems is the coordination of energy production time with demand time, especially if photovoltaic energy sources are present. To face this problem, battery energy storage units (ESU) can be installed. In recent years, more and more attention has been paid to optimizing...
-
Energy Management for PV Powered Hybrid Storage System in Electric Vehicles Using Artificial Neural Network and Aquila Optimizer Algorithm
PublicationIn an electric vehicle (EV), using more than one energy source often provides a safe ride without concerns about range. EVs are powered by photovoltaic (PV), battery, and ultracapacitor (UC) systems. The overall results of this arrangement are an increase in travel distance; a reduction in battery size; improved reaction, especially under overload; and an extension of battery life. Improved results allow the energy to be used efficiently,...
-
Annual variations in the solar energy conversion efficiency in will coppice stand.
PublicationMonitorowano produkcyjność plantacji wiklinowych w Uppsali w Szwecji w latach 1985-1994. Okazało się, że największa sprawność przetwarzania energii słonecznej w biomasę ma miejsce w drugim i trzecim roku uprawy wiklinowej (około 1%), natomiast w pierwszym i w czwartym roku sprawność ta jest 2 razy niższa i wynosi około 0,5%. Dyskutuje się przyczyny takiej sytuacji.
-
Quantum issues in diagnostics of marine energy machines and devices
PublicationW artykule podjęto zagadnienie możliwości uwzględniania części dorobku mechaniki kwantowej w diagnostyce okrętowych urządzeń energetycznych. Wykazano, że są zbieżne spostrzeżenia mechaniki kwantoweji diagnostyki technicznej uzyskane w obszarze wiedzy z zakresu badań empirycznych. Uzasadniono konieczność wykonywania podczas badań empirycznych, nie tylko rachunku błędów, lecz także określania niedokładności wyników badań (pomiarów)...
-
Residual current devices in installations with PV energy sources
PublicationThe paper presents the principles of residual current devices (RCDs) application in photovoltaic (PV) installations. Provisions of standards in this regard are commented on, in particular, attention is drawn to the lack of obligation to use of RCDs in PV installations. The issue of the shape of the earth fault current and the level of leakage currents in such installations are discussed. These factors influence the selection of...
-
Powering the Future by Iron Sulfide Type Material (FexSy) Based Electrochemical Materials for Water Splitting and Energy Storage Applications: A Review
PublicationWater electrolysis is among the recent alternatives for generating clean fuels (hydrogen). It is an efficient way to produce pure hydrogen at a rapid pace with no unwanted by-products. Effective and cheap water-splitting electrocatalysts with enhanced activity, specificity, and stability are currently widely studied. In this regard, noble metal-free transition metal-based catalysts are of high interest. Iron sulfide (FeS) is one...
-
The phenomenon of increasing capacitance induced by 1T/2H-MoS2 surface modification with Pt particles – Influence on composition and energy storage mechanism
PublicationIn this paper, several approaches to the synthesis of molybdenum-based electrode materials for supercapacitors are presented, including anodization, hydrothermal process and annealing. For the material prepared via anodization of a molybdenum plate, followed by a hydrothermal process in thiourea aqueous solution, a thorough study of the Pt-surface modification through repetitive cycling in 1 M sulfuric acid with Pt acting as a...
-
Energy conversion in small water plants with variable speed PM generator
Publication -
Energy conversion in 7-(Diethylamino)coumarin doped PMMA fluorescent fibre
Publication -
ENERGY EFFICIENT AND ENVIRONMENTALLY FRIENDLY HYBRID CONVERSION OF INLAND PASSENGER VESSEL
PublicationThe development and growing availability of modern technologies, along with more and more severe environment protection standards which frequently take a form of legal regulations, are the reason why attempts are made to find a quiet and economical propulsion system not only for newly built watercraft units, but also for modernised ones. Correct selection of the propulsion and supply system for a given vessel affects significantly...
-
Luminescence and energy-storage properties of Pr3+-doped YAlO3 crystals
Publication -
Thermal Energy Storage with PCMs in Shell-and-Tube Units: A Review
PublicationThe paper presents a survey of the experimental and numerical studies of shell-and-tube systems in which phase change material (PCM) is used. Due to the multitude of design solutions for shell-and-tube systems, the emphasis is placed on double-tube (DT), triplex-tube (TT), and multitube (MT) units. Additionally, only single-pass systems are considered. Particular attention is paid to the method of heat transfer intensification....
-
Chestnut-Derived Activated Carbon as a Prospective Material for Energy Storage
PublicationIn this work, we present the preparation and characterization of biomass-derived activatedcarbon (AC) in view of its application as electrode material for electrochemical capacitors. Porouscarbons are prepared by pyrolysis of chestnut seeds and subsequent activation of the obtainedbiochar. We investigate here two activation methods, namely, physical by CO2and chemical usingKOH. Morphology, structure and specific surface area (SSA)...
-
Higher harmonics of converter currents in energy conversion system of small water plants
Publication -
Efficiency analysis of an energy conversion system for a variable speed small hydropower plant
Publication -
Influence of hydrochloric acid concentration and type of nitrogen source on the electrochemical performance of TiO2/N-MoS2 for energy storage applications
PublicationIn this work, nitrogen-doped molybdenum sulfide was directly deposited on titanium dioxide nanotubes substrate (TiO2/N-MoS2) during hydrothermal synthesis. The study focuses on the influence of hydrochloric acid concentration used for the synthesis, with the results indicating its essential role in thioacetamide hydrolysis and thus in the effectiveness of the N-MoS2 deposition. The electrode material itself is characterized by...
-
Red Algae – An Alternative Source of Carbon Material for Energy Storage Application
PublicationNew electrode material obtained by pyrolysis of aquatic biomass macro (red algae) soaked with glucose solution has been characterized by SEM, EDX and Raman spectroscopy. Graphitized carbon was identified by Raman spectroscopy. Galvanostatic cyclic polarization of the materials in contact with 1M LiPF6 electrolyte in EC:DMC (1:1 v/v) and Li as a counter electrode was performed. Specific capacity of the novel material was enhanced...
-
Experimental investigation of thermal energy storage in shell-and-multi-tube unit with nano-enhanced phase change material
PublicationThis paper deals with thermal energy storage with use of nanoparticle enhanced phase change material in shell-and-multitube unit. The experiments are conducted under atmospheric pressure. Paraffin wax and two different fatty acids are used as base phase change material. Graphite and multi-walled carbon nanotubes serve as nanoparticles. Graphite nanoparticles are tested at the concentrations of 0.1%, 1% and 5% by weight, while multi-walled...
-
Recent advances of selected passive heat transfer intensification methods for phase change material-based latent heat energy storage units: A review
PublicationThe following article overviews recent studies regarding heat transfer enhancement methods, explicitly focusing on fins and coils utilization, in phase change material-based latent heat thermal energy storage systems. It discusses the influence of various geometrical and material parameters on the melting and solidification processes, as well as the orientation of the heat transfer surface within the storage tank. Additionally,...
-
Influence of conductive carbon and MnCo2O4 on morphological and electrical properties of hydrogels for electrochemical energy conversion
PublicationIn this work, a strategy for one-stage synthesis of polymer composites based on PNIPAAm hydrogel was presented. Both conductive particles in the form of conductive carbon black (cCB) and MnCo2O4 (MCO) spinel particles were suspended in the three-dimensional structure of the hydrogel. The MCO particles in the resulting hydrogel composite acted as an electrocatalyst in the oxygen evolution reaction. Morphological studies confirmed...
-
Low-Temperature Exfoliated Graphenes: Vacuum-Promoted Exfoliation and Electrochemical Energy Storage
Publication -
On the rising extra storage capacity of ultra-small Fe3O4particles functionalized with HCS and their potential as high-performance anode material for electrochemical energy storage
Publication -
Machine Learning- and Artificial Intelligence-Derived Prediction for Home Smart Energy Systems with PV Installation and Battery Energy Storage
Publication -
Thermodynamic Analysis of a Closed-Cycle Ocean Thermal Energy Conversion Power Plant for Offshore Platforms
Publication -
Ultrathin NiO confined within hollow carbon sphere for efficient electrochemical energy storage
Publication -
Conversion of Degradable Solid Waste into Alternative Energy using Local Wastes as a Binder, Case of Southwestern Ethiopia
Publication -
Symmetric Supercapacitors Based on MnOOH‐Coated Nanoporous Carbon toward High Energy‐Storage Performance
Publication -
A method for evaluating theoretical and real operation of diesel engines in energy conversion formulation taking into account their operating indices
PublicationPrzedstawiono propozycję wartościowania (ilościowego określenia z uwzględnieniem wskaźników) działania dowolnego silnika o zapłonie samoczynnym, na przykładzie okrętowego silnika głównego, w którym zachodzą przemiany energetyczne w określonym czasie. Działanie to rozumiane jest jako przekazywanie energii śrubie napędowej w ustalonym czasie, w którym zachodzi przetwarzanie i przenoszenie energii w formie pracy bądź ciepła. Wartościowanie...
-
Facile synthesis of porous iron oxide/graphene hybrid nanocomposites and potential application in electrochemical energy storage
Publication -
A New Approach of Solidification Analysis in Modular Latent Thermal Energy Storage Unit Based on Image Processing
PublicationThe solidification process of RT18HC in a cylindrical shell and tube storage unit has been studied using a new methodology based on image processing. The main idea of the algorithm is to label the region of solidification and use statistical functions to calculate the dimensions of the solidification front over time. Said analysis includes two methods. The first method is to measure the solid fraction changes during solidification....