Filters
total: 422
filtered: 391
Search results for: PA9, ALUMINIUM, WELDING
-
Application of Extreme Doses of Aluminium for Growth Control of Filmentous Bacteria Microthrix Parvicella in an Activated Sludge System - Laboratory Investigations
PublicationLaboratory investigations of aluminium (PAX-16) application for control of population of filamentous bacteria Microthrix Parvicella in a three-phase bioreactor in lab-scale were performed. Dosing of small aluminium doses (approximately 0.5 mgAl/gMLSS·d) in the period preceding seasonal growth of M.Parvicella failed to prevent mass growth of this microorganism leading to activated sludge bulking phenomenon (SVI-250 ml/gMLSS)...
-
Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
PublicationAmong the emerging new welding techniques, friction stir welding (FSW) is used frequently for welding high-strength aluminum alloys that are difficult to weld by conventional fusion-welding techniques. This paper investigated the effects of tool-positioning factors on the maximum temperature generated in the dissimilar FSW joint of AA6061-T6 and AA7075-T6 aluminum alloys. Three factors of plunge depth, tool offset, and tilt angle...
-
The present state of requirements of international association of classification societies (IACS) for wrought aluminium alloys
PublicationW referacie przedstawiono aktualną sytuację w zakresie stopów aluminium z serii 5xxx i 6xxx do przeróbki plastycznej, ze szczególnym uwzględnieniem zmian w tym zakresie zapoczątkowanych przez unifikację wymagań w dokumentach nr 25 i 26 opublikowanychostatnio przez International Association of Classification Societies (IACS). Jednym z najważniejszych punktów w tych dokumentach jest wymaganie odnośnie przeprowadzania próby odporności...
-
Aluminium w nowoczesnych konstrukcjach budowlanych
Publication -
Spawanie ramy motocyklowej ze stopu aluminium metodami TIG i MIG
PublicationNaprawa uszkodzonych elementów konstrukcji technologiami spawalniczymi może pozwolić na przedłużenie ich eksploatacji przy stosunkowo niskich kosztach i krótkim czasie wyłączenia z użytkowania. W pracy porównano cztery technologie spawania ramy motocyklowej Kawasaki wykonanej ze stopu aluminium PA11 (AW 5754, Wr. nr. 3.3535, AlMg3). Spawanie przeprowadzono procesami TIG oraz MIG z wykorzystaniem materiałów dodatkowych AlSi5, AlMg5Mn...
-
Aluminium in glacial meltwater demonstrates an association with nutrient export (Werenskiöldbreen, Svalbard)
PublicationThe aluminium (Al) cycle in glacierised basins has not received a great deal of attention in studies of biogeochemical cycles. As Almay be toxic for biota, it is important to investigate the processes leading to its release into the environment. It has not yet been ascertained whether filterable Al (passing through a pore size of 0.45 m) is incorporated into biogeochemical cycles in glacierised basins. Our study aims to determine...
-
Selected local stability problems of channel section flanges made of aluminium alloys
PublicationThe paper addresses the issue of local buckling of compressed flanges of cold-formed thin-walled channel columns and beams with nonstandard flanges composed of aluminium alloys. The material behaviour follows the Ramberg–Osgood law. It should be noted that the proposed solution may be also applied for other materials, for example: stainless steel, carbon steel. The paper is motivated by an increasing interest in nonstandard cold-formed...
-
Zastosowanie metody emisji akustycznej i metody dynamicznej elektrochemicznej spektroskopii impedancyjnej do badania odporności korozyjnej stopów aluminium
PublicationPrzedstawiono wyniki badania stopów aluminium metodą DEIS oraz metodą emisji akustycznej. Badania przeprowadzono w roztworze buforu boranowego (pH ) domieszkowanego jonami chlorkowymi w celu zwiększenia agresywności korozyjnej. Obydwa badane stopy aluminium ulegają w tych warunkach korozji wżerowej. Stwierdzono, że pierwsze sygnały emisji akustycznej pojawiają się przy potencjałach niższych niż potencjały, przy których następuje...
-
Surface and Corrosion Properties of AA6063-T5 Aluminium Alloy in Molybdate-containing Sodium Chloride Solutions
PublicationCorrosion properties of aluminium alloy AA6063-T5 were investigated in molybdate-containing NaCl solutions. Electrochemical, microscopic, and spectroscopic experiments were utilized to examine the mechanism of corrosion inhibition by molybdates. SEM-EDX, magnetic force, and intermodulation electrostatic force microscopy data suggested that the inhibition initiation preferentially occurred over Fe-rich cathodic IMPs. Spectroscopic...
-
Numerical simulations of S700MC laser and hybrid welding
Publication -
Numerical Simulation of Duplex Steel Multipass Welding
Publication -
Electric field-assisted dissociation of singlet excitons in tris-(8-hydro-xyquinolinato)aluminium (III)
PublicationW pracy podano szczegółowemu badaniu kompleks organo-metaliczny 8-hydroksy-chinoliny i aluminium (ALq3) metodą pomiaru fotopądów i elektromodulacji luminescencji. Stwierdzono, że w obszarze wysokich pól elektrycznych (F>105 V/cm) ładunek wytwarzany jest w procesie dysocjacji wzbudzonych stanów single-towych. Wyjaśnienie przebiegów prądowych w zakresie niskich pól elektrycznych (F<105 V/cm) wymagało włączenia zjawiska rekombinacji...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Effect of the welding environment and storage time of electrodes on the diffusible hydrogen content in deposited metal
PublicationIn the study the glycerin displacement method was used for determination of diffusible hydrogen content in deposited metal. Specimens were welded in the air and in the water with covered rutile electrodes. The first part of the specimens was made immediately after opening the package of the electrodes. The electrodes were then stored in opened packages in laboratory conditions that allowed for contact with the air for three years....
-
Temperature Evolution, Material Flow, and Resulting Mechanical Properties as a Function of Tool Geometry during Friction Stir Welding of AA6082
PublicationThe friction stir welding process was simulated for joining AA6082 aluminum alloy with the use of the computational fluid dynamics method. Two different tool geometries were used—a tapered cylindrical pin (simple pin) and a hexagonal pin with grooves (complex pin). The analysis of the simulations performed was discussed in terms of temperature evolution during the process, total heat input, residual stresses and material flow....
-
Elasto-viscoplastic properties of AA2017 aluminium alloy
PublicationArtykuł opisuje procedurę identyfikacji parmetrów materiałowych dla sprężysto-lepkoplastycznego modelu Bodnera-Partoma. Prezentowane są symulacje numeryczne testów jednoosiowego rozciągania z różnymi prędkościmi odkształcenia, które porównane są z wynikami eksperymantalnymi.
-
Synthesis and characterization of luminescent aluminium selenide nanocrystals
Publication -
Effect of geometric imperfections on aluminium silo capacities
PublicationAn aluminum silo with initial imperfections is analysed. Two types of imperfections are considered. The first one takes the form of local indentations in the shell; their size and range are adopted on the basis of the standard guidelines. The second type is a global imperfection described through the use of its eigenforms and by means of two-dimensional random fields. The calculations are limited to two cases of loading: negative...
-
Zmęczeniowe badania porównawcze złączy spawanych stopów aluminium Al-Mg5083 oraz Al-Zn-Mg 7010
PublicationBadaniom zmęczeniowym poddano stopy aluminium do przeróbki plastycznej Al-Mg5083 w stanie T6-przesyconym, a następnie sztucznie starzonym oraz stop Al-Zn-Mg 7010 w stanie H321 umocnionym zgniotem i stabilizowanym. Doczołowe złącza spawane wykonano metodami MIG i TIG. Na podstawie uzyskanych wyników badań opracowano zbiorcze wykresy niskocyklowej wytrzymałości zmęczeniowej. Wykazano, że stop Al-Mg 5083 ma wyższą niskocyklową wytrzymałość...
-
Application of Numerical Simulations on 10GN2MFA Steel Multilayer Welding
Publication -
Numerical Simulations of X22CrMoV12-1 Steel Multilayer Welding
Publication -
Heat Source Models in Numerical Simulations of Laser Welding
Publication -
Design of thermal cutting table - welding technology and construction
PublicationW referacie przedstawiono pionierską pracę dyplomową stopnia inżynierskiego, wykonaną przez dwoje studentów Wydziału Mechanicznego Politechniki Gdańskiej zgodnie z systemem CDIO (Conceive, Design, Implement, Operate). W ramach pracy studenci zaprojektowali stół do cięcia termicznego metali (rysunki i obliczenia wytrzymałościowe metodą elementów skończonych), opracowali technologię spawania stołu oraz samodzielnie go wykonali. Stół...
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublicationMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...
-
Evaluation of citric acid corrosion inhibition efficiency and passivation kinetics for aluminium alloys in alkaline media by means of dynamic impedance monitoring
PublicationA novel approach is proposed for constructing the adsorption isotherm in corrosion studies, based on a well-known interaction between citric acid and aluminium in alkaline electrolytes. Our approach utilizes the instantaneous impedance measurements via Dynamic Electrochemical Impedance Spectroscopy in galvanostatic mode (g-DEIS). Unlike other common tools, g-DEIS delivers exact information about the concentration required for full...
-
Pin Angle Thermal Effects on Friction Stir Welding of AA5058 Aluminum Alloy: CFD Simulation and Experimental Validation
PublicationThe friction stir welding (FSW) of tool pin geometry plays a critical role in the final properties of the produced joint. The tool pin geometry directly affects the generation of heat and the flow of internal materials during the FSW process. The effects of the FSW tool pin angle on heat generation and internal flow have not been quantitatively investigated in detail. In this manuscript, a validated Computational Fluid Dynamic...
-
Badania tribologicznych właściwości nanokompozytowych warstw Ni-P/Si3N4 osadzanych metodą redukcji chemicznej na stopie aluminium AW-7075
PublicationPrzedstawiono wyniki tribologicznych badań warstw nanokompozytowych Ni-P/Si3N4 i niklowych Ni-P osadzonych na stopie aluminium AW-7075 metodą redukcji chemicznej, a także stopu AW-7075 bez powłoki. Warstwy nanokompozytowe wytworzono, stosując azotek krzemu Si3N4 w postaci polidyspersyjnego proszku o wielkości cząstek 20–25 nm. Analizowano wpływ zawartości w materiale warstwy fazy dyspersyjnej na twardość i zużycie ścierne, którą...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Fractographic-fractal dimension correlation with crack initiation and fatigue life for notched aluminium alloys under bending load
PublicationIn this study, fatigue fracture surfaces of aluminium alloy 2017-T4 notched specimens were investigated under cyclic bending to find an alternative failure loading index.. The surface topographies were measured on the entire fracture area with an optical profilometer for different loading conditions. Fatigue crack initiation life Ni and total fatigue life Nf were examined using standard surface topography parameters (such as, root...
-
Fracture in composite/aluminium joints of variable adhesive properties
PublicationA strain gauge technique recently developed with the wedge test, for estimating crack length and, thus, the fracture energy of structural adhesive bonding, has been employed on a system in which one adherend had two types of surface treatment. Simple polishing and polishing with subsequent sandblasting were the treatments used, with a distinct straight line, perpendicular to the sample edges, separating the two. Despite the clear-cut...
-
Aluminium Profile Reinforced with Carbon Fibre: Numerical Analysis
Publication -
The aluminium and polycarbonate covering of the canopy above the stadium in Gdansk
PublicationW artykule przestawiono informacje o elementach konstrukcyjnych poszycia zadaszenia stadionu piłkarskiego w Gdańsku zrealizowanego z okazji rozgrywanych w Polsce i Ukrainie mistrzostw Europy w piłce nożnej. Omówione zostały elementy poszycia z poliwęglanu wraz z jego konstrukcją nośną oraz układem odwodnienia. Podano informacje o testach i badaniach przeprowadzonych przed wykonaniem obiektu, które zadecydowały o przyjętych rozwiązaniach...
-
The aluminium and polycarbonate covering to the roof over the stadium in Gdańsk
PublicationThis paper presents information about structural elements of the roof covering to the stadium in Gdansk built for the 2012 European Football Championship in Poland and the Ukraine. The paper discusses elements of the polycarbonate covering, the supporting structure and the drainage system. It also provides information about tests and research performed prior to construction, which determined the solutions adopted as well as...
-
Recykling opakowań ze szkła, aluminium i PET
PublicationW artykule porównano możliwość i korzyści wynikające z recyklingu pojemników typu puszka aluminiowa, butelka szklana i butelka PET. Ocenę przedstawiono na podstawie zebranych danych literaturowych.
-
Understanding the origin of high corrosion inhibition efficiency of bee products towards aluminium alloys in alkaline environments
PublicationVarious bee products were found to be efficient corrosion inhibitors of aluminium in different environments. In particular, bee pollen was found to be highly effective in alkaline electrolytes, yet its highly complex composition and possible synergistic interactions hinder determination of the compounds acting as active corrosion inhibitors. The main purpose of the following work is to investigate the effect of solvents used for...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Monitoring of crosslinking of a DGEBA-PAMAM adhesive in composite/aluminium bonded joint using mechanical and ultra-sound techniques
PublicationAdhesive cure is an important and determining aspect of strength and stability of bonded structures. Crosslinking of the polymer leads to the adhesive strength, stiffness and durability. Depending on the resin and curing agent used, cure time can vary from minutes to weeks, even then 100% crosslinking not being guaranteed. Standard methods based on dynamic mechanical analysis (DMA) or calorimetric techniques (DSC, DTA) are valuable...
-
Numerical Simulations of Laser and Hybrid S700MC T-Joint Welding
Publication -
Computational Techniques in Numerical Simulations of Arc and Laser Welding Processes
Publication -
APPLICATION OF NUMERICAL SIMULATIONS ON X10CRWMOVNB9-2 STEEL MULTILAYER WELDING
Publication -
Corrosion Inhibition of Aluminium Alloy AA6063-T5 by Vanadates: Local Surface Chemical Events Elucidated by Confocal Raman Micro-Spectroscopy
PublicationChemical interactions between aqueous vanadium species and aluminium alloy AA6063-T5 were investigated in vanadate-containing NaCl solutions. Confocal Raman and X-ray photoelectron spectroscopy experiments were utilised to gain insight into the mechanism of corrosion inhibition by vanadates. A greenish-grey coloured surface layer, consisting of V+4 and V+5 polymerized species, was seen to form on the alloy surface, especially on...
-
The influence of plastic working on the selection properties of the nickel - aluminium alloy coatings = Wpływ obróbki plastycznej na wybrane właściwości powłok stopowych nikiel - aluminium
PublicationW pracy przedstawiono wyniki badań nad możliwością zastosowania technologii obróbki plastycznej (walcowania na zimno i gorąco, oraz prasowania) do kształtowania wybranych właściwości natryskiwanych płomieniowo powłok stopowych Ni-5%Al o strukturze jednofazowej, a mianowicie granicznego roztworu stałego , o maksymalnej 10% rozpuszczalności glinu w sieci krystalograficznej niklu. Celem pracy jest wstępna analiza możliwości zastąpienia...
-
Impedance analysis of Portevin-Le Chatelier effect on aluminium alloy
Publication -
On the distribution of aluminium and magnesium oxides in wustite catalysts for ammonia synthesis
Publication -
Aluminium surface treatment with ceramic phases using diode laser
Publication -
Fractal analysis of the bending-torsion fatigue fracture of aluminium alloy
Publication -
Podatność złączy spawanych stopów aluminium na korozję warstwową.
PublicationPrzedstawiono wyniki badań trzech stopów grup Al-Mg i Al-Zn-Mg na korozję warstwową. Wykazano, że mimo zróżnicowanego składu odporność stopów jest podobna, zaś największa korozja występuje w spoinie.
-
Effect of welding conditions on susceptibility to cold cracking of underwater welded joints
PublicationPrzedstawiono wybrane aspekty spawalności stali przy spawaniu pod wodą metodą lokalnej komory suchej. Zwrócono szczególną uwagę na skłonność do tworzenia peknięć zimnych w SWC. Przy pomocy planowania doświadczeń określono ilościowy wpływ parametrów spawania na naprężenia krytyczne z próby implant.
-
Modeling of Heat Source Based on Parameters of Electron Beam Welding Process
Publication -
Numerical Simulation of Electron Beam Welding Process of Inconel 706 Sheets
Publication