Search
Filters
total: 457
filtered: 417
Search results for: power supply
-
ANALYSIS OF DIESEL OIL SPECIFIC HEAT IMPACT FOR OPERATION OF THE SUPPLY PUMP
PublicationThe article describes a test rig that allows the measurement of fuel oil specific heat changes based on the cooling time of liquids. After that, by analysing the test results, a research hypothesis was created and verified. The hypothesis is that the specific heat energy of fuel oil impact the operation of the circulation pump.
-
Modernizaciâ sistemi mikrorajonnogo teplopostačaniâ. Modernization of system of district heat supply.
PublicationOmówiono przykład kompleksowej modernizacji osiedlowego systwmu grzewczego. W jego ramach wprowadzono nowe skojarzone źródło energii elektrycznej i ciepła, wymieniono system rurociagów, zaś budynki dwu osiedli poddano konwencjonalnej termomodernizacji. W budynku jednego z osidli zastosowano układ grzejny oparty na gruntowych pompach ciepła oraz kolektorach słonecznych.
-
Supply current signal and artificial neural networks in the induction motor bearings diagnostics
PublicationThis paper contains research results of the diagnostics of induction motor bearings based on measurement of the supply current with usage of artificial neural networks. Bearing failure amount is greater than 40% of all engine failures, which makes their damage-free operation crucial. Tests were performed on motors with intentionally made bearings defects. Chapter 2 introduces the concept of artificial neural networks. It presents...
-
Transient States during Short-circuit in a Line Powered by UPS and its Impact on Earth Fault Loop Impedance Measurement and Power Quality
PublicationThe short-circuit in a line powered by Uninterruptible Power Supply (UPS) during different UPS operation modes is presented in the article. The transient state condition related to the short-circuit in a line fed from double conversion On-line UPS is discussed in detail. The results of the measurements of earth fault loop impedance (FLI) in circuits powered by UPS with the instruments of various manufacturers are presented. The...
-
Optimisation of cooperation of hybrid renewable energy sources with hydrogen energy storage toward the lowest net present cost
PublicationThe paper presents the results of a technical and economic analysis of the power supply for a model industrial facility based on intermittent renewable energy sources in the form of wind turbines and photovoltaic modules, supplemented with hydrogen energy storage. The adopted power supply strategy assumed the maximisation of self-consumption of self-produced electricity. Six variants were considered, including two with an energy...
-
Protection System Design of Induction Motor for Industries
PublicationThe fundamental and durable structures of induction motor, as well as their low manufacturing cost, make them popular components in a wide range of current applications. Providing a safety net for employees is a must-have for businesses. This project’s motivation for improvement is to provide industrial motors, lift motors, pumps, and so on with safety. An induction motor’s primary goal is to protect it from problems, such as...
-
Protection System Design of Induction Motor for Industries
PublicationThe fundamental and durable structures of induction motor, as well as their low manufacturing cost, make them popular components in a wide range of current applications. Providing a safety net for employees is a must-have for businesses. This project’s motivation for improvement is to provide industrial motors, lift motors, pumps, and so on with safety. An induction motor’s primary goal is to protect it from problems, such as...
-
Voltage and Current Unbalance Reduction in Power Networks with Distributed Generation and Electric Vehicles
PublicationThe current development of prosumer microsources and the expected spread of electric vehicles may cause the appearance of significant current and voltage unbalance in low-voltage (LV) networks. This unbalance, which is an unfavorable phenomenon, may occur when using single-phase photovoltaic (PV) microsources and single-phase home chargers for electric vehicles. This paper presents a proposal for the symmetrization of the LV network...
-
Sustainable Use of the Catenary by Trolleybuses with Auxiliary Power Sources on the Example of Gdynia
PublicationThe current developments in onboard power source technology, in particular, traction batteries, open up new potential in trolleybus transport and also make it possible to introduce electric buses. Thus far, trolleybus transport has required the presence of overhead lines (OHL). Introducing trolleybuses with onboard batteries makes it possible to grow the zero-emissions transport network in places with limited power supply capabilities...
-
Modern Arrangement for Reduction of Voltage Perturbations
PublicationThe contents of this chapter encompass general problems and the most important issues of power-supply-quality improvement in AC systems. In the context of the above, consideration is given to evaluation of bilateral interactions of receivers with an electrical power-distribution system and methods of their reduction. Also are discussed the basis of operation of the most important compensation-filtration devices and their applications...
-
Resonant Conditions in a Node with an SVC Compensator
PublicationThe primary purpose of installing static shunt compensators in power grids is to improve the voltage conditions. Additional reactive power sources increase the system’s voltage stability and enable faster system recovery after a voltage failure. This paper presents the impact of an SVC device’s structure and settings on impedance change in the supply system, and hence on the frequencies at which resonance phenomena can develop.
-
Effect of power frequency on the stress state of disc actuator
PublicationThis paper presents the concept of determining the optimum frequency of coil supply in inductive-dynamic drive. As a criterion to obtain the sought frequency, the smallest value of reduced stress in the disc was assumed while maintaining the desired dynamics. The disc stress is determined on the basis of solution of vibrating thin plate equation. Magnetic pressure acting on the disc is obtained from a hybrid circumferentially-field...
-
Higher harmonics produced by traction substations – computer modelling and experimental verification
PublicationVoltage and current harmonics have a detrimental effect on the components of a power system. Current harmonics may result in the overload and damage to power transformers, although the rms value of load current does not exceed their current-carrying capacity. Voltage harmonics may result in, for example, damage to capacitor banks used to compensate reactive power. Devices which contribute to both current and voltage distortion...
-
Unity-Gain Zero-Offset CMOS Buffer with Improved Feedforward Path
PublicationA voltage unity-gain zero-offset CMOS amplifier with reduced gain error and increased PSRR (power supply rejection ratio) is proposed. The amplifier uses two feed mechanisms, negative feedback and supporting positive feedforward, to achieve low deviation from unit gain over the entire input range. The circuit, designed in a standard 180-nanometer 1.8-voltage CMOS process, is compared with two known buffers of similar topology,...
-
Impact of Industry 4.0 Technologies for Advancement of Supply Chain Management (SCM) Sustainability
Publication -
The new investing effectiveness evaluation multi-criteria method in modern supply systems
PublicationThe important problem in the processes of modelling and programming the development of sustainable energy sector is the multi-criteria manner of assessing the effectiveness of investments. The goal of this paper is to show how to take into account the impact of investments in multidimensional modelling decision-making processes. This goal can be achieved through the development, presentation, and use of a new multi-criteria method...
-
ECU calibration for gaseous dual fuel supply system in compression ignition engines
PublicationThe dual fuel (DF) combustion mode is proven solution that allows to improve or get at the same level engine performance and reduce toxic compounds in exhaust gases which is confirmed by researchers and end-users. DF combustion mode uses two fuels gaseous fuel as a primary energy source and a pilot quantity of diesel fuel as ignition source. However, in order, to fully take advantage of the potential of the dual fuel mode, DF system...
-
Current harmonic controller in multiple reference frames for series active power filter integrated with 18-pulse diode rectifier
PublicationThe paper presents the control system and selected results of experimental tests of the AC/DC power converter consisting of an 18-pulse diode rectifier based on coupled reactors and a serial active power filter. Proportional integral controllers with decoupling components are implemented in multiple reference frames for selective line current harmonic suppression. The regulator is provided with a backtracking anti-windup mechanism...
-
Problems of varistor quality assessment during exploitation
PublicationVaristors are commonly used elements which protect power supply networks against high-voltage surges or lightning. Therefore, quality and endurance of these elements is important to avoid losses when an expensive laboratory equipment would not be protected from random overvoltages. Additionally, excessive leakage currents generate serious costs due to high energy consumption. The paper presents shortly properties of varistors that...
-
Technical and economic conditions of supplying residential consumers with heat from nuclear power plant
PublicationThe reduction of CO2 emission requires technological shift towards carbon-free options. Cogeneration of electricity and heat based on coal and natural gas will experience generation cost increase, if the costs of emissions are imposed on the plant operators. Therefore, nuclear and renewable options should be considered. In this paper, we present the concept of electricity and heat supply system with nuclear condensing turbine adapted...
-
Evaluation of electrical parameters of traction supply system for complex railway traffic conditions, using simulation methods
PublicationDevelopment of electrified transport systems, railways modernization, expansion of urban transport networks, purchases of modern rolling stock causes that updating of electric traction supply system is necessary. This chapter presents an effective method for electrical parameters of traction supply system evaluation, using simulation methods.
-
The Method of Multi-criteria Analysis to Support the Decision on Load or Micro-generation Connection to a Low- or Medium-voltage Power Grid
PublicationThis paper presents a method that supports the decision in terms on selecting the best option of a load connection to a low- or medium-voltage power distribution grid, and of a micro-generation source connection to a low-voltage grid. The method is based on the search for the option with the lowest aggregate assessment measure, which is the weighted average of partial assessment measures determined for each of eight considered...
-
Modeling and experimental investigation of the small UPQC systems
PublicationIn this paper the basis of analytical modelling of the UPQC arrangements (Unified Power Quality Conditioner) in d-q rotating coordinates, as well as select results of investigations conducted on the simplified small power laboratory model were talked over. In short form power balance as well as fundamental dependences and analytic model with regard of decoupling circuits were investigated. Applied method for DC link capacity selection...
-
Research on the Flicker Effect in Modern Light Sources Powered by an Electrical Network
PublicationDisruptions in power quality have a negative impact on many energy consumers. These include lighting, where interference manifests itself, among others, in the form of light flickering. The article presents phenomena accompanying the operation of modern light sources against the background of exemplary results of studies on the flicker of conventional light sources, such as incandescent or fluorescent lamps. The flickering effect...
-
Multiaspect measurement analysis of breaking energy recovery
PublicationNowadays the issue of electric energy saving in public transport is becoming a key area of interest, which is connected both with a growth of environmental awareness in the society and an increase in the prices of fuel and electricity. That is why the reduction of energy consumption by increasing electrified urban transport, such as trams, trolleybuses, light rail and underground is becoming an increasingly important issue. Energy...
-
Comprehensive circumscribing of non-linearity cases of a water supply system with smooth flow control
PublicationW artykule opisano formalnie poprawne metody opisu matematycznego pracy pomp o płynnie regulowanych wydatkach oraz reduktorów ciśnienia i reduktorów przepływu w modelowaniu przepływów ustalonych zachodzących w systemach wodociągowych. Opisano metodę opartą o dynamiczną analizę wrażliwości systemu oraz metodę wykorzystującą charakterystyki hydrauliczne systemu wodociągowego. Przedstawiono wyniki symulacji wykorzystującej ww. metody...
-
Risk-averse decision-making to maintain supply chain viability under propagated disruptions
Publication -
Ancient settlements-atavistic solutions for present water supply and drainage problems engendered by urbanism
PublicationWater is the most valuable resource available on earth. Although it is present in abundance, its usable volume is very scarce. This is the reason behind the existence of both floods and droughts around the world. However, human settlements face water scarcity issues that are primarily engendered by improper town planning measures. To create a balance between the available fractions of water, it is therefore imperative to have proper...
-
Random components influence on the values characterising periodic disturbances in low voltage supply lines.
PublicationAnalizowano wpływ składowych losowych na wielkości charakteryzujących zaburzenia okresowe w napięciu zasilania na przykładzie współczynnika zawartości harmonicznych (THD). Zaprezentowano sposób wyznaczania niepewności pomiaru współczynnika THD, uwzględniający występowanie korelacji pomiędzy składową podstawową i kolejnymi harmonicznymi napięcia sieci a także między poszczególnymi harmonicznymi. Przedstawiono analizę wyników z pomiarów...
-
Experiment-Based Study of Heat Dissipation from the Power Cable in a Casing Pipe
PublicationThe paper deals with the important challenges in terms of electricity transmission by means of underground cable lines. The power cable’s performance is characterized by an ampacity that represents its maximum electric current-carrying capacity. The ampacity of power cables depends on their ability to diffuse the heat generated by the current flow into the environment. In the performed research, the analysis of the efficiency of...
-
Koncepcja zdalnego sterowania i monitoringu urządzeń trakcyjnych z wykorzystaniem technologii teleinformatycznych
PublicationAdvancement in wireless communication enables engineers to apply sophisticated and relatively inexpensive technologies in new fields of industry, which were previously designated solely to wire-based solutions. One of those fields is railway transportation system. In effect of a high reliability and safety demands, this area was resistive to new technologies. Nowadays, increased security and reliability of wireless sensor networks...
-
Niskonapięciowy filtr analogowy CMOS wykorzystujący konwerter ujemnoimpedancyjny
PublicationA low-voltage 3-order low-pass CMOS filter based on the novel current inversion type negative impedance converter (CNIC) is presented. It shows a badwidth of 10 MHz at 400 uW power consumption and 2 V supply voltage when realized in a 0.35 um CMOS process.
-
Niskonapięciowy filtr analogowy CMOS oparty o konwerter ujemno-impedancyjny
PublicationA low-voltage 3-order low-pass CMOS filter based on the novel current inversion type negative impedance converter (CNIC) is presented. It shows a badwidth of 10 MHz at 400 uW power consumption and 2 V supply voltage when realized in a 0.35 um CMOS process.
-
Winding function approach based design of novel five-phase brushless doubly fed induction generator
PublicationThe paper presents the concept of the new design of the five-phase brushless doubly fed induction generator. The generator is dedicated to the modern wind turbine. The innovative design approach uses a five-phase power supply from the stator control winding side of the generator with a stator three-phase classic power winding. The research results presented indicate that the electromagnetic coupling between the control and power...
-
Concept of Wireless Low-Voltage DC Socket for the Residential House Application
PublicationThe proposed research is devoted to the comprehensive theoretical and experimental study of the concept of the wireless low power dc socket for residential applications. The main goal of this work is to provide safe dc source for residential customers at power level which is enough in order to supply all typical appliances without power factor correctors. Such types of devices can be already connected to the dc grid and decoupled...
-
Programmable Input Mode Instrumentation Amplifier Using Multiple Output Current Conveyors
PublicationIn this paper a programmable input mode instrumentation amplifier (IA) utilising second generation, multiple output current conveyors and transmission gates is presented. Its main advantage is the ability to choose a voltage or current mode of inputs by setting the voltage of two configuration nodes. The presented IA is prepared as an integrated circuit block to be used alone or as a sub-block in a microcontroller or in a field...
-
Fully Tunable Analog Biquadratic Filter for Low-Power Auditory Signal Processing in CMOS Technologies
PublicationA novel Gm-C structure of a second-order continuous-time filter is proposed that allows for the independent control of the filter’s natural frequency (ω0) and quality factor (Q). The structure consists of two capacitors and four transconductors. Two transconductors together with the capacitors form a lossless second-order circuit with tunable ω0. The other two transconductors form a variable gain amplifier (VGA) which realizes...
-
Diagnosis of bearing damage in induction motors by instantaneous power analysis
PublicationResearch of the machine with simulated bearing damages has been carried out, where variable load torque, simulating bearing damage, was introduced. The results show that components which can be used for bearings diagnosis appear in the spectrum of the product of current and supply voltage instantaneous values. These components are easier to identify than the components of current spectrum, which have been used so far in diagnostic...
-
On the use of a charge balancing method for low energy measurements
PublicationThe paper presents the method for the estimation of the energy consumption of the low-power microcontroller-based devices. Due to high dynamics of the changes of the supply current of the tested devices during the operational cycle, the consumed energy estimation is not easy. In order to avoid disadvantages of known methods, the charge balancing method was employed similarly like in some types of A/D converters.
-
Low temperature rotary Stirling engine: conceptual design and theoretical analysis
PublicationThe use of low-temperature energy sources for electricity generation demands a dual focus: a substantial enhancement in the efficiency of energy conversion devices and a reduction in system production costs. Particularly in scenarios where low-temperature energy sources are scarce, this factor can be pivotal in facilitating widespread adoption of such technologies. The Stirling engine emerges as a promising solution capable of...
-
25 kV–50 Hz railway supply modelling for medium frequencies (0–5 kHz)
Publication -
Chapter 1 : Supply system influence on behaviour of an elektromechanical model - four bar/dc motor
PublicationPraca opisuje zagadnienia wspólnego modelowania układu wieloczłonowego i napędu elektrycznego. Analizowanym układem mechanicznym jest płaski czworobok przegubowy. Analizowany mechanizm zamodelowano jako układ wieloczłonowy z zamkniętymi wielobokami ciał. Do wymuszenia ruchu układu wykorzystano model silnika prądu stałego. Zaproponowano kilka alternatywnych sposobów zasilania silnika. Układem referencyjnym jest źródło prądu stałego....
-
Asymmetrical Modes in Polyphase Motors and Drives
PublicationThe effect of power supply and/or motor asymmetry on the phase-load distribution and the ripple of electromagnetic torque in a polyphase drive is studied by the method of symmetrical components. It is shown that the presence of asymmetry causes the mapping of all harmonics in the supply voltage into all planes of symmetrical components and eliminates the possibility of independent control of harmonics. The dynamic model of a five-phase...
-
Interference between Land and Sea Logistics Systems. Multifunctional Building System Design Towards Autonomous Integrated Transport Infrastructure
PublicationThe research is focused on developing design theory towards efficient multifunctional facilities for logistics supply chains in the contemporary urban city structures. The development of modern systems based on autonomous transport creates new conditions for their management and generates an emerging need to define dedicated functional service structures. An important element of consideration also taken into account is the scenario...
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublicationThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
Optimization of hybrid parallel application execution in heterogeneous high performance computing systems considering execution time and power consumption
PublicationMany important computational problems require utilization of high performance computing (HPC) systems that consist of multi-level structures combining higher and higher numbers of devices with various characteristics. Utilizing full power of such systems requires programming parallel applications that are hybrid in two meanings: they can utilize parallelism on multiple levels at the same time and combine together programming interfaces...
-
Remote current measurement with FPGA digital processing
PublicationThe work presents an implementation of a modular measurement and control systemthat controls variants of mains supply of 230V electrical equipment. The system allowsto supervise power consumption in the office electronic equipment. The system detectsthe instant of the reduced power consumption by a device and makes possible itsswitch-off in order to reduce energy cost. The current is measured with integratedcurrent/voltage converters....
-
Static Series and Shunt-series PE Voltage-quality Controllers
PublicationAs presented in the Chap. 7 static shunt power electronics (PE) voltage-quality controllers protect the utility electrical system from the unfavorable impact of customer loads. Shunt controllers, as shown in Chap. 6, are recommended mainly for mitigation of the causes of disturbances, and not their effects in distanced nodes of a power-electronics system. In the case when reduction of disturbances effects is required, which leads...
-
Construction of a simulation model of goods delivery in international road transportation taking into account the functioning efficiency of logistics supply chain
PublicationThe object of this study is the process of goods delivery in international road transport using various types of logistics chains. The problem being solved is due to the need to develop recommendations for exporters of goods to reformat or design new supply chains during wartime. The expediency of organizing foreign trade operations by the cargo owners' own forces or with the involvement of enterprises providing logistics consulting...
-
Space Mission Risk, Sustainability and Supply Chain: Review, Multi-Objective Optimization Model and Practical Approach
Publication