Search
Filters
total: 798
filtered: 666
Search results for: cr-doped srtio3
-
Electrical and structural properties of Nb-doped SrTiO3
PublicationNiobium-doped strontium titanate synthesized via conventional solid-state reaction has been studied. Influence of niobium content on the lattice parameters and electrical conductivity has been reported. Various reduction conditions have been investigated. For samples reduced in hydrogen at 1400°C, a transition from thermally activated to metallic behavior has been observed. Maximum electrical conductivity (ca. 55 Scm−1 at 650°C)...
-
Electrical and structural properties of Nb-doped SrTiO3 ceramics
PublicationPrzebadano wpływ zawartości niobu na strukturę i własności elektryczne tytanianu strontu. Zbadany został wpływ warunków redukcji i porowatości na właściwości materiału. Za optymalne uznano domieszkowanie niobem w wysokości 2% molowych.
-
Fabrication and structural properties of Y and Fe co-doped SrTiO3 nanoceramics for SOFC
PublicationYttria and iron co-doped strontium titanate perovskites, (Y0,07Sr0,93Ti1-xFexO3-δx=0,1; 0,2) samples were fabricated by two methods: solid-state synthesis (SS) and the Pechinisol-gel modified method. The morphology of samples were measured by SEM and X-raydiffraction. Results were compared and discussed. The strong relationship between fabricationprocedure and microstructure has been proven. It was also observed, that the nanoceramicsobtained...
-
Structural and electrical properties of Cr-doped SrTiO 3 porous materials
PublicationSeries of single-phase materials with assumed formula SrTi1−xCrxO3 (where x = 0, 1, 4, 6 mol.%) were obtained by sol-gel method. The structure and microstructure of materials were characterised by X-ray diffraction and scanning electron microscopy methods. Moreover, the study of electrical properties and evaluation of chemical stability in CO2/H2O atmosphere was performed by electrochemical impedance spectroscopy and thermogravimery...
-
Characterization methods of nickel nano-particles obtained by the ex-solution process on the surface of Pr, Ni-doped SrTiO3 perovskite ceramics
PublicationIn this paper, a novel electrode material based on Pr, Ni co-doped strontium titanate ( Sr0.7Pr0.3)xTi1−yNiyO3 with constant amount of 30% praseodymium dopant, different amount of nickel (y = 0.06 and y = 0.10) and additional nonstoichiometry in Sr-site (x = 1; x = 0.9 and x = 0.8) was investigated as fuel electrode for SOEC devices. A porous ceramics were prepared by solid-state reaction method. X-ray diffraction measurements...
-
Characterization and properties of low-friction, multilayered Cr-doped diamond-like carbon coatings prepared by pulse biased filtered cathodic arc deposition
Publication -
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublicationIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Effect of Cr and Mn doping on ferroelectric and dielectric properties of Li1.72Na0.28Ge4O9 single crystals
PublicationLi1.72Na0.28Ge4O9 single crystals pure and slightly doped with chromium and manganese, obtained by Czochralski growth, were investigated for their ferroelectric and dielectric properties. The change in stoichometry of Li2− x Na x Ge4O9 (x = 0.28) crystals doped with Cr and Mn (0.1 mol.%) had an influence on the value of ferroelectric-to-paraelectric phase transition temperature, T c. The applied doping affects the T c value by...
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublicationThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Microstructural and electrical properties of Y0.07Sr0.93-xTiO3-δ perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontiumtitanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work.It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent.Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry.The defect...
-
Microstructural and electrical properties of Y0.07Sr0.93-xTiO3 perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Microstructural and electrical properties of Y0:07Sr0:93−xTiO3− perovskite ceramics
PublicationIn order to find a relationship between electrical and microstructural properties, yttrium-doped strontium titanate (7 mol%) with various values of strontium nonstoichiometry was investigated and shown in this work. It has been observed that yttrium doping can affect the electrical properties of SrTiO3 to a great extent. Moreover, the microstructural and electrical properties can be influenced by strontium nonstoichiometry. The...
-
Structural and electrical transport properties of Pr-doped SrTi0.93Co0.07O3-δ a novel SOEC fuel electrode materials
PublicationSolid Oxide Electrolyzer Cells (SOECs) are very promising electrochemical devices for the production of syngas (H2/CO) by H2O and CO2 co-electrolysis. The structure, microstructure and electrical properties of the fuel electrode material play a crucial role in the performance of the whole cell and efficiency of electrocatalytic reduction of steam into hydrogen. In the present work, a novel Co and Pr co-doped SrTiO3-δ material attracted...
-
In-situ Cu-doped MnCo-spinel coatings for solid oxide cell interconnects processed by electrophoretic deposition
PublicationThe Cu doping of the Mn–Co spinel is obtained “in-situ” by electrophoretic co-deposition of CuO and Mn1.5Co1.5O4 powders and subsequent two-step reactive sintering. Cu-doped Mn1.5Co1.5O4 coatings on Crofer22APU processed by electrophoretic co-deposition method are tested in terms of long term oxidation resistance and area specific resistance tests up to 3600 h. The introduction of Cu in the spinel lead to higher level of densification...
-
Corrosion behaviour of Cr coatings deposited from Cr(III) formate - urea electrolytes
PublicationPowłoki chromowe były otrzymane z elektrolitów Cr(III) zawierających odpowiednie ligandy, zapewniające ich dobry wygląd. Zbadano wpływ hydrazyny oraz hydrohylo aminofosfatu na właściwości korozyjne Cr otrzymanego z kąpieli mocznikowo-formaldehydowych Cr(III). Właściwości warstw testowano przy pomocy metody EIS rejestrując widma impedancyjne dla próbek o różnych czasach ekspozycji w zakwaszonym roztworze siarczanowym ( pH 2,6) stosując...
-
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublicationThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Environmental degradation of the Cr-Mo steels in liquid hydrocarbons
PublicationPrzedstawiono podatność stali stopwych 26H2MF i 34HNM do naprężeniowego pękania korozyjnego. Środowiskiem do badań było paliwo ciężkie i zużyty olej mineralny.
-
TiO2 /SrTiO3 and SrTiO3 microspheres decorated with Rh, Ru or Pt nanoparticles: Highly UV–vis responsible photoactivity and mechanism
PublicationA series of TiO2/SrTiO3 and SrTiO3 microspheres decorated by Rh, Ru or Pt NPs were prepared by facile hydrothermal method. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) with energy-dispersive Xray (EDX) spectroscopy, scanning electron microscopy (SEM), photoluminescence spectrometry (PL), Fourier transform infrared (FT-IR) and...
-
The effect of imidazolium ionic liquid on the morphology of Pt nanoparticles deposited on the surface of SrTiO3 and photoactivity of Pt–SrTiO3 composite in the H2 generation reaction
PublicationPhotocatalytic water splitting has great potential in solar-hydrogen production as a low-cost and environmentally friendly method. Different unique techniques used to obtain photocatalysts with various modifications to improve H2 generation have been introduced. In the present work, SrTiO3 was successfully synthesized via the solvothermal method in the presence of ionic liquid (IL) - 1-butyl-3-methylimidazolium bromide ([BMIM][Br])...
-
Corrosion and hydrogen intake for some Cr-Mn steels in liquid hydrocarbons
PublicationStal 34HNM i 26H2MF, poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej przy pomiarach ze stałą szybkością rozciągania (10-6s-1) i pomiarach niskocyklowego zmęczenia, wykonanych w paliwie kotłowym. Mechanizm korozji naprężeniowej określono jako kruchość wodorowa, co zostało potwierdzone w pomiarach pochłaniania wodoru z tych środowisk. Jako możliwe źródła wnikania wodoru do stali omówiono procesy korozyjne,...
-
Studies on novel BiyXz-TiO2/SrTiO3 composites: Surface properties and visible light-driven photoactivity
PublicationA series of novel BiyXz-TiO2/SrTiO3 composites were prepared by multistep synthesis route. The asprepared photocatalysts were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), diffuse reflectance spectroscopy (DRS), Fourier transform infrared (FT-IR), Raman spectra and BET analysis. The photocatalytic activity test was performed in aqueous solution of phenol under...
-
Catalysts for advanced oxidation processes: Deep eutectic solvents-assisted synthesis – A review
PublicationNew catalyst synthesis techniques, including green materials, are extensively studied for heterogeneous photocatalytic advanced oxidation processes (AOPs) on spotlight of sustainable development. Deep eutectic solvents (DESs) started to be used in this field as environmentally friendly alternative to ionic liquids (ILs). During the catalyst synthesis, DESs can act as stabilizers, capping agents, structure directing agents, templates,...
-
Processing and properties of Al-Si-Fe-Cr in situ composites
PublicationPraca jest kontynuacją badań nad wytwarzaniem tanich kompozytów in situ o osnowie stopu Al-Si wzmocnionego związkami międzymetalicznymi Al-Fe-Si lub Al-Fe-Cr-Si, otrzymanych poprzez reakcję ciekłego stopu Al (Al-Si11, Al-Si25) z proszkiem Fe lub Cr. Żelazo zostało wybrane ze względu na niską cenę, niską temperaturę wytwarzania, wysoką reaktywność z Al i heksagonalną sieć krystalograficzną związku Al-Fe-Si, co sprzyja tworzeniu...
-
Charakterystyka kawitacyjna laserowo obrabianych napoin Fe-Cr-Mn
PublicationPrzedstawiono badania odporności kawitacyjnej napoin Fe-Cr-Mn w dwóch przypadkach: bez dodatkowej obróbki powierzchniowej oraz po przetapianiu powierzchni napoiny wiązką lasera CO2 o mocy 1000W. Oceniano głębokość i stopień umocnienia warstwy wierzchniej.
-
Effect of laser heating on cavitation behaviour of Fe-Cr-Mn coating.
PublicationW pracy przedstawiono badania odporności kawiracyjnej napoiny Fe-Cr-Mn po obróbce laserowej polegającej na przetapianiu napoiny wiązką lasera CO2 o mocy 1000W oraz jej nagrzewaniu w stanie stałym. Rezultaty badań wskazują,że po każdym rodzaju obróbki występuje inna podatność obrobionej powierzchni do odkształceń plastycznych pod działaniem obciążeń kawitacyjnych.
-
Visible light photocatalysis employing TiO2/SrTiO3-BiOI composites: Surface properties and photoexcitation mechanism
PublicationA series of binary TiO2/SrTiO3 and ternary TiO2/SrTiO3_BiOI composites have been synthesized using multistep preparation method. Characterization of the obtained photocatalysts covered complex analysis including morphology + y (SEM), BET specific surface area, porosity, optical properties (DRS), chemical composition of surface (XPS), crystal structure and crystal size (XRD). UV–vis and Vis ligh induced photocatalytic activity was...
-
Adsorption of Cr(VI) in aqueous solution using sago bark (Metroxylon sagu) as a new potential biosorbent
PublicationThis paper investigated the ability of sago bark (Metroxylon sagu) as a new potential biosorbent in removing Cr(VI) in batch system. The optimum adsorption capacity of sago bark (Metroxylon sagu) was 61.73 mg/g achieved at pH 3, agitation rate of 100 rpm, contact time 60 min, particle size ≤32 μm, and initial concentration of Cr(VI) 1,000 mg/L at room temperature (25°C). The adsorbent regeneration was carried out using 0.01 M HNO3...
-
Influence of laser beam machining on the cavitation resistance of Fe-Cr-Co clad.
PublicationW pracy przedstawiono wpływ laserowego nagrzewania bezzmiany stanu skupienia i laserowego przetapiania napoin ze stopu Fe-Cr-Co na ich odporność kawitacyjną. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Plastyczne odkształcenia powierzchni określano za pomocą analizy obrazów erodowanych powierzchni. Uzyskane rezultaty wskazują, że laserowo obrabiane powierzchnie miały różną podatność do plastycznego odkształcania...
-
Effects of Sr/Ti stoichiometry in SrTiO3-based SOFC anodes
PublicationScharakteryzowano wpływ stechiometrii Sr/Ti na właściwości strukturalne, elektryczne i mechaniczne anod na bazie tytanianu strontu. Wyjaśniono genezę niektórych zjawisk w oparciu o chemię defektów związków niestechiometrycznych na bazie istniejących pozycji literaturowych.
-
Synthesis and properties of HoT2Al20 (T = Ti, V, Cr) intermetallic cage compounds
PublicationPolycrystalline samples of HoT2Al20 (T = Ti, V, Cr) intermetallics were synthesized using a step-wise arc-melting technique. All three compounds adopt the CeCr2Al20-type crystal structure with Ho atoms positioned inside oversized icosahedral cages formed by Al atoms. The structure of HoV2Al20 compound is reported. The materials properties were studied by means of electrical resistivity, magnetic susceptibility, and specific heat...
-
Intensity Ratio of Kβ/Kα in Selected Elements from Mg to Cu, and the Chemical Effects of Cr Kα1,2 Diagram Lines and Cr Kβ/Kα Intensity Ratio in Cr Compounds
Publication -
PROPERTIES OF DOPED ALKALINE-EARTH STANNATES
PublicationThe lanthanum doped barium stannate properties are investigated in this work. Including electrical and microstructural properties.
-
Transformation of polyvinyl chloride (PVC) into a versatile and efficient adsorbent of Cu(II) cations and Cr(VI) anions through hydrothermal treatment and sulfonation
PublicationThe reuse of waste polyvinyl chloride (PVC) has drawn much attention as it can reduce plastic waste and associated pollution, and provide valuable raw materials and products. In this study, sulfonated PVC-derived hydrochar (HS-PVC) was synthesized by two-stage hydrothermal treatment (HT) and sulfonation, and shown to be a versatile adsorbent. The reoval of Cu(II) cations and Cr(VI) anions using HS-PVC reached 81.2 ± 1.6% and 60.3...
-
Wpływ długotrwałej eksploatacji na strukturę i własności mechaniczne stali Cr-Mo-V,
PublicationW artykule omówiono zagadnienie oceny stopnia degradacji stali Cr-Mo-V pracujących w warunkach pełzania. Przedstawiono wyniki badań diagnostycznych rury 273x32,0 mm głównego rurociągu parowego po eksploatacji w temperaturze 540C przez 168 000 godzin. Przeprowadzono badania metalograficzne za pomocą mikroskopu świetlnego oraz skaningowego i transmisyjnego mikroskopu elektronowego, a także badania własności mechanicznych materiału...
-
Comparison of the paracetamol electrochemical determination using boron-doped diamond electrode and boron-doped carbon nanowalls
PublicationTwo different type of electrodes, boron-doped diamond electrode (BDD) and boron-doped carbon nanowalls (B:CNW) electrode, were used for the electrochemical determination of paracetamol using the cyclic voltammetry and the differential pulse voltammetry in phosphate buffered saline, pH = 7.0. The main advantage of these electrodes is their utilization without any additional modification of the electrode surface. The peak current...
-
Structural and electrochemical heterogeneities of boron-doped diamond surfaces
PublicationThis brief review is focussed on the recent progress in studies of the heterogeneous electrochemical behaviour of various boron-doped materials extending from zero-dimensional particles through polycrystalline or nanostructured three-dimensional surfaces. A boron-doped diamond reveals large heterogeneities induced by numerous factors, inter alia multi-faceted crystallinity, inhomogeneous boron concentration, sp2/sp3-carbon ratio,...
-
Rapid development of the photoresponse and oxygen evolution of TiO2 nanotubes sputtered with Cr thin films realized via laser annealing
PublicationRecently, earth abundant transition metal oxides have gained particular attention as potential catalyst candidates due to their availability and low-cost comparing to substrates containing precious Pt or Au species. Herein, we present characterization of morphology, structure and electrochemical properties of pulsed 532 nm laser treated TiO2 nanotubes (NT) sputtered by the thin film of chromium. Scanning electron microscopy enables...
-
Fabrication and characterization of boron-doped nanocrystalline diamond-coated MEMS probes
PublicationFabrication processes of thin boron-doped nanocrystalline diamond (B-NCD) films on silicon-based micro- and nano-electromechanical structures have been investigated. Nanocrystalline boron doped -diamond (B-NCD) films were deposited using Microwave Plasma Assisted Chemical Vapour Deposition (MW PA CVD) method. The variation of B-NCD morphology, structure and optical parameters were particularly investigated. The use of truncated...
-
Superconductivity and ferromagnetism in Pd doped Y9Co7
PublicationThe ferromagnetic superconductor Y9Co7 was chemically doped to yield the solid solution Y9Co7-xPdx for 0 < x < 0.4. The lattice parameter a does not depend on x, whereas c increases with increasing Pd content up to x ¼ 0.2, the palladium solubility limit. The transition from ferromagnetism (TC ¼ 4.25 K) to superconductivity (Tsc ¼ 2.4 K) was observed only for the parent Y9Co7 compound. For the lowest tested Pd doping level (x ¼...
-
In-situ optical diagnostics of boron-doped diamond films growth
PublicationInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Enhanced photoelectrochemical and photocatalytic performance of iodine-doped titania nanotube arrays
PublicationThe paper discusses the synthesis and performance of iodine doped titania nanotube arrays exhibited under irradiation. The doping procedure was performed as an additional, electrochemical process carried out after formation of nanotube arrays via anodization of Ti substrate. The optical and structural properties were characterized using Raman, UV-vis, photoluminescence and X-ray photoelectron spectroscopy. The surface morphology...
-
Structure and thermoelectric properties of nickel-doped copper selenide synthesised in a hydrogen atmosphere
PublicationNickel-doped copper selenide—Cu2-xNixSe (x = 0; 0.01; 0.02; 0.03)—materials with high thermoelectric properties were synthesised through reduction of reagents in hydrogen. The impact of the nickel content on both the microstructure and thermoelectric properties was examined. The nickel-doped samples’ microstructure differed significantly from pristine copper selenide. Besides Cu2Se, copper precipitations were present in the materials....
-
Pr-doped TiO2: The effect of metal content on photocatalytic activity
PublicationThe Pr-TiO2 nanoparticles were prepared by using the sol-gel method. As-prepared samples were characterized by BET measurements, X-ray powder diffraction analysis (XRD) and UV-Vis spectra. Visible and ultraviolet light photocatalytic activity of the sample was studied by photodegradation of phenol while considering the influence of the dopant concentration. TiO2 doped with 0.25 mol% of praseodymium showed the highest photocatalytic...
-
Electrical characterization of diamond/boron doped diamond nanostructures for use in harsh environment applications
PublicationThe polycrystalline boron doped diamond (BDD) shows stable electrical properties and high tolerance for harsh environments (e.g. high temperature or aggressive chemical compounds) comparing to other materials used in semiconductor devices. In this study authors have designed electronic devices fabricated from non-intentionally (NiD) films and highly boron doped diamond structures. Presented semiconductor devices consist of highly...
-
Fabrication of La-Doped Bi4Ti3O12 Ceramics
PublicationLa-modified Bi4Ti3O12 is a typical ferroelectric, piezoelectric and electro-optic material, having relatively low coercive field, low dielectric constant, high Curie temperature and high breakdown strength. Goal of the present research was to apply mixed oxide method for fabrication of BiTLax ceramics, study its chemical composition, crystalline structure and microstructure. The compound BiTLax for x=0, 0.25, 0.5, 0.75 ceramic...
-
Luminescent properties of Ln3+ doped tellurite glasses containing AlF3
PublicationThe low-phonon energy tellurite glasses TeO2-BaO-Bi2O3 and TeO2-BaO-Bi2O3-AlF3 triply doped with Eu3+, Tb3+, Tm3+ ions in two different molar ratios were synthesized using melt-quenching technique. Their structure and luminescence properties were widely investigated by X-ray Diffraction (XRD), Differential Scanning Calorimetry (DSC), Fourier Transform Infrared Spectroscopy (FTIR) and Photoluminescence Spectroscopy (PL). The luminescence...
-
DFT studies of the refractive index of boron-doped diamond
PublicationThe density functional theory is one of the optimal solutions in calculation of optical properties of materials on the quantum scale. In this paper, we have investigated the refractive index of a boron-doped diamond structure with the usage of Atomistic Toolkit software from Synopsys. During this study, various methods and pseudopotentials were checked to obtain an optimal performanceaccuracy method for calculation of such materials....
-
Susceptibility of Cr-Ni-Mn steel to the hydrogen degradation in boiler fuel = Podatnośc stali Cr-Mn-Ni na niszczenie wodorowe w paliwie kotłowym
PublicationStal 34HNM poddana różnym obróbkom cieplnym wykazała skłonność do korozji naprężeniowej w pomiarach ze stałą niską szybkością rozciągania i do zmęczenia korozyjnego niskocyklowego. Mechanizmem zniszczenia była degradacja wodorowa. Możliwe źródła pochłaniania wodoru to: korozja, degradacja węglowodorów z tworzeniem się kwasów organicznych i promotorów wnikania wodoru.
-
Water uptake analysis of acceptor-doped lanthanum orthoniobates
PublicationIn this work, lanthanum orthoniobates doped with either antimony, calcium, or both have been synthesized and studied. The water uptake of the investigated materials has been analyzed by means of thermogravimetric studies. The results show the difference between the thermodynamics of hydration between the lanthanum orthoniobate system and other proton conducting ceramics. The relation between the water uptake and effective acceptor...
-
Facile preparation of extremely photoactive boron-doped TiO2 nanotubes arrays
PublicationDoping of TiO2 nanotube arrays with boron was realized via electrochemical treatment of as-anodized titania immersed in electrolyte containing boric acid. The photoactivity of doped and pure titania was examined by means of photoelectrochemical and photocatalytic response under UV-vis irradiation. The results showed that photocurrent density of B-TNTs is remarkably higher (7.5 times) than density of pure TiO2 nanotube arrays. Furthermore,...