Search results for: TEXAS OVERLAY TESTER
-
EGNOS-based GNSS receiver for precise positioning in restricted areas
PublicationPositioning accuracy is very important in many areas, whereas the typical GPS receiver accuracy is often not sufficient. The European Geostationary Navigation Overlay Service (EGNOS), Europe’s first venture into satellite navigation, improves the open public service offered by the Global Positioning System (GPS). As a satellite navigation augmentation system, EGNOS improves the accuracy of GPS by providing a positioning accuracy...
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublicationPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Badania komunikacji pomiędzy urządzeniami automatyki zabezpieczeniowej zgodnie ze standardem IEC 61850
PublicationW artykule opisano badania modelu sieci SN wyposażonego w przekaźniki REF615 Serii Relion firmy ABB oraz tester zabezpieczeń CMC 256-6 firmy OMICRON. Na stanowisku badawczym na Wydziale Elektrotechniki i Automatyki Politechniki Gdańskiej przeprowadzono badania czasu przesyłania komunikatów GOOSE oraz retransmisji danych za pomocą testera zabezpieczeń CMC 256-6. Wyniki potwierdziły niezawodność oraz powtarzalność czasów przesyłu...
-
Zespolone techniki informatyczne w analizie struktury produkcji i wynikówekonomicznych dla korporacji przemysłu elektronicznego. Zamoj. Stud. i Ma-ter.**2003 z. 1 s. 109-116, 6 rys. 2 tab. bibliogr. 11 poz. Seria: Informatyka. Materiały z konferencji '' Informatyka w szkole''.
PublicationW artykule przeanalizowano strukturę produkcji oraz wyniki ekonomiczne czte-rech wiodących korporacji pzremysłu elektronicznego: Analog Devices, Intel,Texas Instruments i Motorola. Przy wykorzystaniu pakietu Microsoft Acces o-pracowana została baza danych zawierająca podstawowe informacje o korporac-jach. Zaproponowano i wykonano analizy porównawcze w zakresie finansowo-eko-nomicznym oraz przedstawiono przewidywania dotyczące...
-
Using an IEEE1149.1 Test Bus for Fault Diagnosis of Analog Parts of Electronic Embedded Systems
PublicationThe new solution of a BIST called the JTAG BIST for self-testing of analog parts of electronic embedded systems is presented in the paper. The JTAG BIST consists of the BCT8244A and SCANSTA476 integrated circuits of Texas Instruments controlled via the IEEE 1149.1 bus. The BCT8244A is a scan test device with octal buffers, and the SCANSTA476 is a 12-bit ADC with 8 analog input channels. Self-testing approach is based on the fault...
-
Pawel Polaczyk dr inż.
PeopleDr. Pawel Polaczyk is a scholar in civil engineering and a civil engineering practitioner in pavement engineering. Dr. Polaczyk is originally from Warsaw, Poland, where he received his B.Sc. degree in Civil Engineering with a concentration in Transportation from Warsaw University of Technology. His Master`s and Doctorate degrees in Civil Engineering with a concentration in Geotechnology and Materials Engineering are from the University...
-
System pomiarowy sygnałów wyjściowych z elektrochemicznych czujników gazów
PublicationW pracy przedstawiono koncepcję systemu służącego do pomiarów zawartości związków lotnych w powietrzu. Proponowany system składa się z kilku identycznych modułów pomiarowych zbierających dane z czujników elektrochemicznych. Pojedynczy moduł wykonany jest na bazie układu LMP91000 firmy Texas Instruments. Dane z modułów, po wstępnej obróbce przy pomocy mikrokontrolera trafiają do komputera PC. Komputer, będący centralnym punktem...
-
Projektowanie oraz implementacja cyfrowego multiefektu gitarowego z wykorzystaniem procesora sygnałowego
PublicationW artykule został przedstawiony proces projektowania i realizacji cyfrowego multiefektu gitarowego z wykorzystaniem procesora sygnałowegoTMS320C5535 firmy Texas Instruments, dla którego oprogramowanie napisano w języku C. Omówiono zasady działania oraz algorytmy wybranych efektów dźwiękowych, które zostały zaimplementowane w procesorze sygnałowym. Zaprojektowano również uniwersalny moduł wejściowy zawierający wzmacniacz z regulowanym...
-
Performance analysis of power swing blocking feature in ABB 670 series impedance relays
PublicationThis paper presents test results of a distance protection’s PSD power swing detection feature in ABB 670 series relays. A RED670 relay was tested, which is part of the hydroelectric set protection in Żarnowiec Pumped Storage Plant. The power swing blocking feature’s performance was analysed on the basis of the results of object tests made with an Omicron digital tester. Also presented are simulation results that illustrate the...
-
Complex modulus of Cement Bitumen Treated Material Mixture (28 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with 3 combinations of binding agents: 2% cement, 6% emulsion (C2E6), 6% cement, 6% emulsion (C6E6), 6% cement, 2% emulsion (C6E2). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains...
-
Data from 76- to 81-GHz mmWave Sensor located at S7 road
Open Research DataThe set consists data recorded employing IWR1642 mmWave sensor from Texas Instruments. The purpose of the experiment was to detect vehicles and their speed in real conditions – at S7 road, near Dworek village (54°14'40.0"N 18°59'59.0"E).
-
Transformacja tożsamości miejsca jako efekt interwencji artystycznych w przestrzeni publicznej
PublicationThe subject of a paper is connected with art in public space as an element of shaping identity of a place. This issue is related to finding out new and effective urban regeneration’s tools, rebuilding the identity of degraded areas by art. In the article, the idea of an American “creative placemaking” is presented and compared with polish urban regeneration case study. The specific issues discussed in the article are: the role...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 laboratory mixed/laboratory compacted (7-365 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in laboratory conditions on the basis of materials obtained from...
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 field mixed/laboratory compacted (7-365 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in the field conditions and later compacted in laboratory. Mixture...
-
Results of calibration of the piezoelectric scanner using the probe TGQ1
Open Research DataTeaching file. Results of calibration of the piezoelectric scanner using the probe TGQ1. Scanning in contact mode. NTEGRA Prima (NT-MDT) device. CSG probe 10.
-
Monitoring of underdeck corrosion by using acoustic emission method
PublicationThis paper presents first short characteristics of underdeck corrosion process as well as a problem of its monitoring. Next is described an acoustic emission (AE) method elaborated by Department of Ship Technology , Quality Systems and Material Engineering, Gdańsk University of Technology in cooperation with partners of CORFAT project realized within 7th EU Frame Program . Further are presented short characteristics of the emission...
-
Methodology for Processing of 3D Multibeam Sonar Big Data for Comparative Navigation
PublicationAutonomous navigation is an important task for unmanned vehicles operating both on the surface and underwater. A sophisticated solution for autonomous non-global navigational satellite system navigation is comparative (terrain reference) navigation. We present a method for fast processing of 3D multibeam sonar data to make depth area comparable with depth areas from bathymetric electronic navigational charts as source maps during...
-
Procesory sygnałowe - 2022/2023
e-Learning CoursesKurs przeznaczony dla studentów 6 semestru studiów I stopnia, kierunek EiT. Kurs przedstawia architekturę procesorów sygnałowych na kilku wybranych konstrukcjach firmy Texas Instruments oraz Analog Devices. Prezentuje także sposoby ich programowania oraz omawia przykładowe, popularne algorytmy cyfrowego przetwarzania sygnałów, jakie są realizowane przez takie procesory.
-
Procesory sygnałowe 23/24
e-Learning CoursesKurs przeznaczony dla studentów 6 semestru studiów I stopnia, kierunek EiT. Kurs przedstawia architekturę procesorów sygnałowych na kilku wybranych konstrukcjach firmy Texas Instruments oraz Analog Devices. Prezentuje także sposoby ich programowania oraz omawia przykładowe, popularne algorytmy cyfrowego przetwarzania sygnałów, jakie są realizowane przez takie procesory.
-
Jarosław Guziński prof. dr hab. inż.
PeopleJaroslaw Guzinski received M.Sc., Ph.D. and D.Sc. degrees from the Electrical Engineering Department at Technical University of Gdansk, Poland in 1994, 2000 and 2011 respectively. Since 2016 he is Associate Professor at Gdansk University of Technology. Currently he is the head of the Department of Electric Drives and Energy Conversion. From 2006 to 2009 he was involved in European Commission Project PREMAID Marie Curie, ‘Predictive...
-
Service-based Resilience for Embedded IoT Networks
PublicationEmbedded IoT networks are the backbone of safety-critical systems like smart factories, autonomous vehicles, and airplanes. Therefore, resilience against failures and attacks should be a prior concern already in their design stage. In this study, we introduce a service-based network model as an MILP optimization problem for the efficient deployment of a service overlay to the embedded network by meeting QoS and resilience requirements....
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E4 cores obtained from the field section (28-365 days of curing at the field and later in laboratory at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Specimen were obtained from the field at 28, 180, 270 and 365 days after compaction....
-
Complex modulus of Cement Bitumen Treated Material Mixture C3E5.5 (over 28 days of curing at 20C)
Open Research DataDataset presents data of complex modulus determined for cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement and 5.5% emulsion (C3E5.5). Mixture was designed according to Polish requirements for the base course of pavement. Mixture contains 60% of RAP material. Specimen size: f=100 mm, h=130 mm. Specimen...
-
Komunikacja między komputerem a procesorem sygnałowym z zastosowaniem protokołu RTDX. Zastosowanie Komputerów w Nauce i Technice. XIII cykl seminariów zorganizowanych przez PTETiS, Oddział Gdańsk.
PublicationW artykule opisano możliwości realizacji komunikacji między komputerem osobistym a procesorem sygnałowym TMS320C6711 firmy Texas Instruments. Scharakteryzowano własności karty uruchomieniowej ze zmiennoprzecinkowym procesorem sygnałowym TMS320C6711 pod kątem zastosowań dydaktyczno-naukowych. Przedstawiono przykłady praktycznych rozwiązań procedur komunikacyjnych, utworzonych w środowiskach programistycznych Visual C++ oraz LabView,...
-
The Effect of Water and Frost on Fatigue Life of Asphalt Concrete
PublicationThis paper presents testing of fatigue life of asphalt concrete that has been subjected to action of water and frost. Simulation of water and frost action was based on the original AASHTO T283 method and its modification. The original method was modified in such a way that instead of a single freeze-thaw cycle, 50 and 150 cycles were applied. Fatigue life was measured in the indirect tensile fatigue test in the Nottingham asphalt...
-
Built-in Test Scheme for detection, classification and evaluation of nonlinearities
PublicationW artykule przedstawiono koncepcję testera wbudowanego (BIST) przeznaczonego do detekcji nieliniowości, klasyfikacji rodzaju nieliniowości i oceny zniekształceń nieliniowych sygnału testowanego, bez użycia drogiego systemu automatycznego testowania. Tester bazuje na modulatorze sigma-delta umieszczonym na pakiecie testowanym i sztucznej sieci neuronowej zaimplementowanej w komputerze osobistym. Koncepcję testera zweryfikowano poprzerz...
-
Analiza i ocena smarności olejów w ujęciu energetycznym i działania układu tribologicznego = Analysis and evaluation of oil lubricity from the viewpoint of energy apects and of the tribological system action
PublicationBased on measurement results, an interpretation is presented of the tribological system boundary layer action in the form of a four-ball tester friction node. The evaluation was performed of the boundary layer action understood as transfer of energy Ep resulting from loading the tribological system in a determined time t with work Lp, which may lead to breaking the boundary layer. That energy and time are the values unequivocally...
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublicationThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublicationThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Fatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
Open Research DataFatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
-
The new SDMT-family of servo-drives for CNC systems with AC permanent magnet synchronous motors
PublicationW artykule przedstawiono strategię sterowania podstawowe parametry oraz wyniki badań nowej rodziny serwonapędów typu SDMT. Układ sterowania serwonapędu zbudowano na procesorze sygnałowym TMS320F2812 firmy Texas Instruments. W serwonapędzie zastosowano metodę sterowania tupu FOC (ang. Field Oriented Control). Regulatory położenia, prędkości i momentu zreali-zowano na bazie klasycznego regulatora PID z układem ograniczenie sygnału...
-
Tomasz Wierzbowski mgr inż.
People -
Has EGNOS its own place in maritime navigation?
PublicationGNSS (in fact it usually means GPS) is at the moment the fundamental means of positioning for any variants of navigation. However some attributes of it can be not sufficient for every users or in some tasks, so there are any cases when this system needs support. From the mariner point of view pure GPS properties perfectly fulfils expectations of sailors at the open sea, however there are lot of cases, when accuracy of the system...
-
Grade of service determination methodology in IP networks with SIP protocol
PublicationAlthough Grade of Service is very important in VoIP providers evaluation, We wasn't able to find any paper regarding the topic of measuring GoS variables for IP networks utilizing SIP, which are defined like for PSTN/ISDN/GSM networks (post-selection delay, answering delay, release delay, or probability of end-to-end blocking). Due to the lack of research in this field, it was necessary to start from defining measures and cover...
-
Reliability model of slide bearings with particular attention given to lubricating oil
PublicationThe paper presents the slide bearing with circulating lubrication as a system of series three-element structure, where lubricating oil is the weakest link. In accordance with the Pierce statement that ''strength of chain is the strength of its weakest link'', a bearing reliability model has been developed. It allows to use the lubricating oil to evaluate the probability of correct working of the whole slide bearing, i.e. the reliability....
-
Wpływ smarowności na działania układu tribologicznego (impact of lubricity on the tribological system action)
Publicationthe paper presents analysis and evaluation, based on tests results, of the impact of lubricity of the used lubricating oils (shell argina t 40) on the action of boundary layer of sulzer 6zl40/48 engines aboard the ''włocławek'' sea-going ship. for comparison purposes, the same oils were tested with the ceramizer four-stroke engine (all types of the vidar four-stroke engines) regeneration agent added. so understood boundary layer...
-
Wizyjny system monitoringu stanu nakładek stykowych odbieraków prądu
PublicationEksploatowane do niedawna w Polsce nakładki pantografów kolejowych były wykonywane w postaci styków miedzianych. Na początku 2011 r. przeprowadzono kompleksową zmianę typu nakładek stykowych, stosowanych przez operatorów korzystających z infrastruktury PKP PLK S.A., z miedzianych na metalizowane węglowe. Wraz z wprowadzeniem nakładek węglowych istnieje potrzeba opracowania nowych metod diagnostyki tego istotnego elementu toru zasilania...
-
THE RESEARCH ON EGNOS SYSTEM IN CONTEXT OF THE ABILITY TO DETERMINE THE SHIP’S HULL SPATIAL ORIENTATION
PublicationThe European Geostationary Navigation Overlay Service (EGNOS) thanks to geostationary satellites covers an area of whole Europe, including Baltic and North Sea. It allows to fix the coordinates of object position with typical absolute accuracy of 1,5 m. Previous research have shown that relative accuracy is usually higher than absolute one [Nowak A., 2010, Nowak A., 2011], so probably it could be possible to use EGNOS to determine...
-
Efektywne programowanie procesora TMS320C6711 przy użyciu pakietu SIMULINK.
PublicationW artykule opisano alternatywny, w stosunku do standardowych metod kodowania, sposób programowania procesora TMS320C6711 z wykorzystaniem bibliotek pakietu SIMULINK. Scharakteryzowano własności karty uruchomieniowej ze zmiennoprzecinkowym procesorem sygnałowym TMS320C6711 firmy Texas Instruments, pod kątem tworzenia programów do układów prototypowych. Opisano także cechy pakietu SIMULINK jako wydajnego narzędzia pozwalającego na...
-
Paweł Robert Surowiec mgr lic.
PeoplePhD student at The John Paul II Catholic University of Lublin (Poland), STL degree (specialisation: Ecumenism) awarded in 2022. Roman Catholic priest ordained in 2017. He is interested in the works and theology of saint John Henry Newman (1801-1890). A graduate of catholic Higher Theological Seminary of the Diocese of Sandomierz (Poland) and the John Paul II Catholic University of Lublin. He likes to spend time actively - in prayer,...
-
Contactless hearing aid designed for infants
PublicationIt is a well known fact that language development through home intervention for a hearing-impaired infant should start in the early months of a newborn baby's life. The aim of this paper is to present a concept of a contactless digital hearing aid designed especially for infants. In contrast to all typical wearable hearing aid solutions (ITC, ITE, BTE), the proposed device is mounted in the infant's bed with any parts of its set-up...
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublicationThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
Durability of Asphalt Concrete Subjected to Deteriorating Effects of Water and Frost
PublicationThe paper presents testing of the detrimental effects of water and frost on asphalt pavements. It included laboratory testing of 5 fatigue life of asphalt concrete that was subjected to action of water and frost and field testing of damages caused by water and frost on 6 existing asphalt pavements, such as stripping, raveling, and potholes. Laboratory simulation of water and frost action was based on the 7 original AASHTO T283...
-
Demonstrator testera wbudowanego BIST dla układów w pełni różnicowych
PublicationPrzedstawiono demonstrator testera wbudowanego, przeznaczony do pracy na stanowisku dydaktycznym w laboratorium z przedmiotu Zaawansowane Metody Pomiarowe i Diagnostyczne. Na stanowisku studenci zapoznają się z technologią BIST (ang. Built-In Self-Test), która jest przykładem wdrożenia strategii projektowania dla testowania.
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublicationThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
Study of Nanohydroxyapatite Coatings Prepared by the Electrophoretic Deposition Method at Various Voltage and Time Parameters
PublicationThe aim of the work is to compare the properties of nanohydroxyapatite coatings obtained using the electrophoretic deposition method (EDP) at 10 V, 20 V, and 30 V, and with deposit times of 2 and 5 min. The primary sedimentation was used to minimize the risk of the formation of particle agglomerates on the sample surface. Evaluation of the coating was performed by using a Scanning Electron Microscope (SEM), Energy-Dispersive Spectroscopy...
-
Research of chitosan coatings deposited by electrophoretic deposition method at various voltage and time parameters
PublicationThe aim of this research is to estimate the electrophoretic deposition main parameters, such as voltage and time duration, that will provide optimal characteristics of the surface layer. Chitosan coatings were synthesized on biomedical Ti13Zr13Nb alloys at 20 V and 30 V and with deposit times of 2min, 5 min, 10 min, and 15 min. Evaluation of the coating was performed by using Scanning Electron Microscope (SEM), Energy-Dispersive...
-
Nanocrystalline diamond microelectrode on fused silica optical fibers for electrochemical and optical sensing
PublicationFabrication process of thin boron-doped nanocrystalline diamond (B-NCD) microelectrode on fused silica single mode optical fiber has been investigated. The B-NCD films were deposited on the fibers using Microwave Plasma Assisted Chemical Vapor Deposition (MW PA CVD) at glass substrate temperature of 475 ºC. We have obtained homogenous, continuous and polycrystalline surface morphology with the mean grain size in the range of 100-250...