Search
Search results for: propulsion shaft fatigue
-
THE MODELLING OF ACCUMULATION AND DISSIPATION OF ENERGY IN MECHANICAL DRIVE SYSTEM
PublicationThis paper presents a modelling of accumulation and dissipation energy in simple drive system. The simple drive system is presented by laboratory stand designed for calculate fatigue life of material for bending and rotation tests pieces. The laboratory stand was prepared to diagnosis of fatigue life of material by use energetic methods. This idea was submitted as utility model to Polish Patent Office. This laboratory stand gives...
-
EVALUATION OF EFFECTIVENESS OF WATERJET PROPULSOR FOR A SMALL UNDERWATER VEHICLE
PublicationT he goal of the project described is to replace the existing propulsion system of a small underwater vehicle with a solution less prone to mechanical damage and ensuring a lower risk of the entanglement of fibrous objects suspended in the body of water. Four typical marine screws are utilised in the current design of the vehicle. One possible solution of the problem is the application of waterjet propulsors located...
-
ENERGY EFFICIENT AND ENVIRONMENTALLY FRIENDLY HYBRID CONVERSION OF INLAND PASSENGER VESSEL
PublicationThe development and growing availability of modern technologies, along with more and more severe environment protection standards which frequently take a form of legal regulations, are the reason why attempts are made to find a quiet and economical propulsion system not only for newly built watercraft units, but also for modernised ones. Correct selection of the propulsion and supply system for a given vessel affects significantly...
-
The harmonic distortion of voltage waveforms in the ship's electrical power system
Open Research DataThe dataset is a part of the research results on the quality of supply voltage on bus bars of the ship's electrical power system's main switchboard in different states of ship exploitation. The attached dataset contains the results of a harmonic distortion analysis expressed by the total harmonic distortion (THD) coefficient of voltage waveforms recorded...
-
Calculations of notch stress factor of a thin-walled spreader bracket fillet weld with the use of a local stress approach
PublicationPresence of geometric notches in welded joints causes concentration of strains and stresses, therefore reducing fatigue strength of such joints. This article presents an analysis of stress concentrations in a fillet weld of a spreader mounting bracket on a small sailing yacht. The aim of this article is to direct the attention of designers, manufacturers and regulatory bodies to issues of fatigue cracks that form in brackets fastening...
-
Reducing common mode voltage and bearing currents in quasi - resonant DC - link inverter
PublicationIn the paper, a concept of separation of an inverter-fed induction motor drive from its mains supply by two transistor switches inserted in the dc-link circuit is reexamined based on the proposed parallel quasi-resonant dc-link inverter (PQRDCLI). The objective of the paper is to show an advantage of the proposed topology in limiting high frequency common mode voltage and bearing currents. In the laboratory setup, an induction...
-
Zespół wypalenia zawodowego i zmęczenie w kontekście pracy zmianowej i stresu zawodowego wśród pielęgniarek chirurgicznych
PublicationTwo aspects of work-related consequences among surgery nurses are discussed: burnout syndrome and fatigue, having an impact on the quality of medical care and safety of patients. Siegrist's effort-reward imbalance model has been adopted as a concept of occupational stress. The organization of working time, i.e. the length of shifts and their rotation, was considered. Nurses on twelve-hour shifts worked much harder, were more tired...
-
A model of stealth maritime object having some innovative solutions concerning the object form, structure and materials.
Open Research DataThe aim of the project is to work out a model of the stealth maritime object which will have innovative solutions concerning the object form, structure and materials. These solutions should enable a modification of combinations of the object features defining the object stealth characteristics (difficulty of the object detection in the water). It is...
-
Fracture Areas Quantitative Investigating of Bending-Torsion Fatigued Low-Alloy High-Strength Steel
PublicationIn this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus...
-
REDUNDANCY AS A WAY INCREASING RELIABILITY OF SHIP POWER PLANTS
PublicationOne of key ways of assuring a high level of reliability of a ship power plant is to design redundancy of its structural elements, for example redundancy of prime drivers, drivelines etc. This paper deals with issues related to the redundancy as a way increasing dependability of the ship power and propulsion systems. Especially, fundamental characteristics of dependability, major design strategies influencing the reliability, and...
-
Bearing capacity of monotonically installed tapered piles in medium dense Fontainebleau sand
PublicationA series of installation of tapered piles in medium-dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of piles with three different shapes - straight profile (S), and with taper angle of 0.70 degrees (T1), and 1.4 degrees (T2) were used. The piles were instrumented with fiber optic wires on the shaft and load cell at the base. After monotonic installation, the models were...
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublicationThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Strain energy density and entire fracture surface parameters relationship for LCF life prediction of additively manufactured 18Ni300 steel
PublicationIn this study, the connection between total strain energy density and fracture surface topography is investigated in additively manufactured maraging steel exposed to low-cycle fatigue loading. The specimens were fabricated using laser beam powder bed fusion (LB-PBF) and examined under fully-reversed strain-controlled setup at strain amplitudes scale from 0.3% to 1.0%. The post-mortem fracture surfaces were explored using a non-contact...
-
Analiza warunków pracy silnika spalinowego lokomotywy na biegu jałowym
PublicationW trakcie eksploatacji lokomotyw z silnikami spalinowymi obserwowany jest znaczny udział pracy silnika spalinowego w stanie biegu jałowego. Dlatego też średnia wartość strumienia paliwa zużywanego przez silnik spalinowy lokomotywy w tym stanie będzie miała istotny wpływ na efektywność energetyczną układu napędowego. Wyznaczaniu wartości tego parametru musi towarzyszyć jednoznaczna klasyfikacja warunków pracy układu napędowego lokomotywy....
-
The voltage on bus bars of the main switchboard of the ro-ro ship electrical power system during maneuvering
Open Research DataThe dataset is part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. The attached dataset contains the measurement results carried out onboard a ro-ro ship during maneuvering.
-
NEW DESIGNS OF CENTRIFUGAL MAGNETIC FLUID SEALS FOR ROTATING SHAFTS IN MARINE TECHNOLOGY
PublicationThe centrifugal magnetic fluid seals have important advantage over the conventional centrifugal seals. They maintain very good sealing capacity at static, medium and high speeds of shaft rotation, with the increased seal lifetime, and minimum torque and static friction. These seals are particularly useful in cases when the angular shaft velocity varies and sometimes decreases to nearly or exactly zero, such as in flywheel applications,...
-
Team project I (2020/21)
e-Learning CoursesWithin this team project, students will be designing a space mission. Each student will choose a subsystem: mission analysis, propulsion, communication, structure, mechanisms, power, thermal, onboard data handling. Together, by means of concurrent engineering a primary system definition will be completed.
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublicationThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
REPORT Verification expertise of Detroit Diesel engines 16V149TI on the vessel ORP GEN. PUŁASKI
PublicationVerification expertise of propulsion engines for generating sets of the ORP GEN. PUŁASKI - type 16V149TI related to a complaint sent by the shipowner to Shiprepair Yard NAUTA S.A.
-
Redundancja jako sposób zwiększenia niezawodności siłowni okrętowych
PublicationJednym z istotnych sposobów zapewnienia wysokiego poziomu niezawodności siłowni okrętowych jest zaprojektowanie redundancji jego elementów strukturalnych, np.: nadmiarowości strukturalnej systemów generowania energii, układów napędowych itp. W niniejszym artykule omówiono zagadnienia związane z nadmiarem, jako sposobem zwiększenia niezawodności systemów generowania energii i napędu statku. W szczególności zaś zostały zaprezentowane...
-
Structural design and sensitivity analysis of semi-rigid pavement of a motorway
PublicationThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (USA) were applied. For fatigue cracking of cement stabilized bases the Dempsey (USA) and De Beer (South Africa) criteria...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
On the Use of Selected 4th Generation Nuclear Reactors in Marine Power Plants
PublicationThis article provides a review of the possibility of using different types of reactors to power ships. The analyses were carried out for three different large vessels: a container ship, a liquid gas carrier and a bulk carrier. A novelty of this work is the analysis of the proposal to adapt marine power plants to ecological requirements in shipping by replacing the conventional propulsion system based on internal combustion engines...
-
Cyclic behaviour modelling of additively manufactured Ti-6Al-4V lattice structures
PublicationThe present work is concerned with the numerical modelling of the cyclic behaviour of Ti-6Al-4V lattice structures. In the study, diamond structures of titanium alloy produced by the additive laser powder bed fusion (LPBF) method with different degrees of relative density were used. Realistic geometric models of the studied mesostructures were generated using computed microtomography, taking into account the imperfections of the...
-
Assesment of operation of ship main diesel engine using the theory of semi-markovian and markov processes.
PublicationTo precisely determine the task it is necessary to specify also its duration time, apart from conditions in which it will be realized. When considering propulsion engine, i.e. the main element of ship propulsion system, especially important becomes not only the problem which amount of energy could be at one's disposal but also within which time interval it could be delivered. Therefore apart from applying the commonly used reliability...
-
The voltage on bus bars of the main switchboard of the car carrier electrical power system at sea trials during a bow thruster start-up
Open Research DataThe dataset is a part of the research results on the quality of supply voltage on bus bars of the main switchboard of the ship's electrical power system in different states of ship exploitation. In ships' electrical power systems, disturbances occurring in voltage waveforms on bus bars of the main switchboard are connected mainly with the processes...
-
Hertzian Crack Propagation in Ceramic Rolling Elements
PublicationThe properties of ceramics are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such crack are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations are based on a three dimensional model for the ring crack propagation. The stress intensity factors along crack...
-
Microwave Ring Resonator Based Pressure Sensor
PublicationThis paper demonstrates a microwave pressure sensor, which is based on microstrip line-fed ring resonators. The first ring resonator is loaded with the concentric cylindrical shafts, while the same number of the hollow shanks as the shafts are mounted on the second ring resonator. The arrangement of the cylindrical shaft and hollow shank allows for mechanical movement between two substrates while maintaining electrical contact....
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publication -
Quantitative Assessment of Operation of Ship Main Diesel Engine
PublicationOperation of ship propulsion system is associated with realization of definite operational goals. If to elements of the system the operational reliability strategy could be applied, the situation would be very simple as existing conditions would unambiguously determine application of means being on hand. However decision to reject application of the strategy (even if hypothetical) becomes obvious with a view of necessity of ensuring...
-
Wpływ równości nawierzchni i dynamicznego oddziaływania pojazdów ciężkich na trwałość zmęczeniową nawierzchni podatnych
PublicationPodczas ruchu pojazdu obserwuje się odchylenia nacisków osi pojazdów od nacisku statycznego, co jest spowodowane nierównościami nawierzchni. Dynamiczne obciążenia pojazdów w większym stopniu wytężają konstrukcję nawierzchni drogowej. Rozkład obciążeń dynamicznych ma kształt rozkładu normalnego i jest opisywany poprzez obciążenie statyczne oraz wskaźniki dynamiczne DI lub DLC. Wraz z pogorszeniem równości i zwiększeniem prędkości...
-
Crack propoagation in MgO-PSZ ceramic materials
PublicationThe properties of ceramic materials such as elevated hardness, high temperature capability, low coefficient of thermal expansion are of interest for rolling element materials. Widely used ceramic materials in engineering applications are silicon nitride, zirconia and alumina. The paper presents an experimental study of the fatigue life of MgO-PSZ ceramic material in lubricated contact with defined types of cracks. A ceramic angular...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublicationTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Simplified method of water cooled exhaust system design.
PublicationThe water cooled exhaust systems are not often used onboard ships. Prime goal is to lower temperature of exhaust gas from main propulsion and auxiliary engines to the defined limit. The design of such systems require detailed analysis of propulsion system operational parameters to meet designer expectations. The paper outlines the cooled exhaust system design problems in specific application. The simplified method of evaluation...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Analysis of Ceramic Elements with Ring-Crack Defects in Lubricated Rolling Contact
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. Surface ring cracks on lubricating rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculations...
-
Equivalent standard manoeuvres for pod-driven ships
PublicationProcedures for carrying out the manoeuvring tests presented in International Maritime Organisation (IMO) resolution MSC.137(76) are based on the capabilities of ships with conventional steering-propulsion systems. Therefore they do not correspond to ships with other steering-propulsion devices, like pod drives. IMO is aware of this shortcoming and for ships with non-conventional steering and propulsion system may permit the use...
-
LCF behavior of 2024AA under uni- and biaxial loading taking into account creep pre-deformation
PublicationThis study presents the results of experimental low-cycle fatigue (LCF) tests of aluminum 2024 alloy T3511 temper in uni- and biaxial loading states. Tests were carried out on both the as-received material (hardened extruded rods) and material with different pre-deformation histories. These deformations were carried out in the creep process at 200 °C and 300 °C for two different levels of at each temperature. The pre-deformed material’s...
-
Durability of Asphalt Concrete Subjected to Deteriorating Effects of Water and Frost
PublicationThe paper presents testing of the detrimental effects of water and frost on asphalt pavements. It included laboratory testing of 5 fatigue life of asphalt concrete that was subjected to action of water and frost and field testing of damages caused by water and frost on 6 existing asphalt pavements, such as stripping, raveling, and potholes. Laboratory simulation of water and frost action was based on the 7 original AASHTO T283...
-
Marek Dzida dr hab. inż.
PeopleHe was born on 6 August 1953 in Bielsko-Biała. He is a graduate of the Institute of Shipbuilding at Gdańsk University of Technology. Since 1978 he has been working at Faculty of Ocean Engineering and Ship Technology at GUT. In 1983 he received the title of Doctor of Technical Sciences, and in 2001 – the title of Doctor with habilitation. He is currently employed as Associate Professor at GUT. He worked as vice-dean for Education...
-
Numerical analysis of crack propagation in silicone nitride
PublicationThe properties of ceramics, specifically low density, high hardness, high temperature capability and low coefficient of thermal expansion are of most interest to rolling element manufacturers. The influence of ring crack size on rolling contact fatigue failure has been studied using numerical fracture analysis. Such cracks are very often found on ceramic bearing balls and decrease fatigue life rapidly. The numerical calculation...
-
APPLICATION OF REDUNDANCY IN SHIP POWER PLANTS OF OFFSHORE VESSEL
PublicationPower and propulsion systems of offshore units must be of a very high level of reliability. The loss of ability to perform functions of their components causes generally to very high economic losses, which may be increased by unused the weather window resulting to postponing the planned offshore operations. To ensure carrying out so expensive offshore operations in the most reliable way, various types of redundancies are built-in...
-
Structural Design and Sensitivity Analysis of Semi-Rigid Pavement of a Motorway
PublicationThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (1981) were applied. For fatigue cracking of cement stabilized bases the Dempsey (1984) and De Beer (1992) criteria were...
-
Doktorant PG – Jutronauta w NASA
PublicationMgr inż. Adam Dąbrowski, doktorant i asystent na Wydziale Mechanicznym, został laureatem konkursu Gazety Wyborczej „Jutronauci. Bilet za horyzont”, w ramach którego odbył staż w Jet Propulsion Laboratory (JPL), laboratorium NASA w Pasadenie w Kalifornii.
-
Możliwości redukcji przebiegowego zużycia paliwa przy zastosowaniu elektronicznych systemów wspomagających kierowców
PublicationElektroniczne systemy wspomagające kierowcę pomagają kierującym kontrolować sytuację na drodze, przekazują sygnały do układu hamulcowego i napędowego, rozpoznają znaki drogowe, pozwalają utrzymać odpowiedni dystans w czasie jazdy w kolumnie, a także kontrolują położenie pojazdu na pasie ruchu. Elek-troniczne systemy wspomagające kierowcę pomagają również zmniejszyć przebiegowe zużycie paliwa, poprzez odpowiednie sterowanie układem...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Identification of residual force in static load tests on instrumented screw displacement piles
PublicationOccurrence of the so-called residual force of an unknown value significantly disturbs interpretation of static load tests performed on piles equipped with additional measuring instruments. Screw displacement piles are the piling technology in which the residual force phenomenon is very common. Its formation mechanism is closely related to the installation method of this type of piles, which initiates generation of negative pile...