Search
Search results for: LOW TEMPERATURES
-
Reclaiming ground tire rubber at low temperatures: benefits and limitations
PublicationLower extrusion temperatures during rubber reclamation lead to a reduction in toxic degradation products and improve the mechanical properties of vulcanizates, at the expense of reduced processability.
-
Assessment of Tensile Strength Reserve of Asphalt Mixtures at Low Temperatures
PublicationDuring winter conditions, low-temperature cracks develop at the surface of the asphalt pavement when tensile thermal stress induced in the asphalt layer during cooling equals and exceeds the tensile strength of the material. The paper presents the results of tensile strength reserve assessment of asphalt mixtures with neat and SBS-polymer modified bitumen application. The tensile strength reservewas calculated as difference between...
-
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublicationProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
Achieving Efficient and Stable Deammonification at Low Temperatures—Experimental and Modeling Studies
PublicationThe short-term effects of temperature on deammonification sludge were evaluated in a laboratory-scale sequencing batch reactor (SBR). Mathematical modeling was used for further evaluations of different intermittent aeration strategies for achieving high and stable deammonification performance at decreasing temperatures. As for the biomass cultivated at high temperatures (e.g., 30 C), a higher temperature dependency (the adjusted...
-
Asphalt concrete subjected to long-time loading at low temperatures – Deviations from the time-temperature superposition principle
PublicationThe article presents the observed deviations from the time-temperature superposition principle of asphalt concretes, tested in the bending beam creep test at low temperatures for a long time of loading. In almost all tested asphalt concretes, deviations appeared after 500 s of loading at the temperature of -10 C. Some types of bitumen presented deviations at other temperatures – usually the harder the grade of the bitumen, the...
-
Influence of design of hydraulic components on their operation in low ambient temperatures
PublicationW artykule przestawiono wpływ konstrukcji zespołów hydraulicznych na ich działanie w niskich temperaturach otoczenia.
-
Determination of ability of hydrotronic systems to start in low ambient temperatures
PublicationPrzedstawiono wyniki badań symulacji komputerowej zespołów układów hydrotronicznych w warunkach szoku termicznego. Pokazano metodę określania zdatności hydrotronicznych zespołów i układów podczas rozruchu w warunkach szoku termicznego.
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublicationThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
RESEARCH OF HYDRAULIC PISTON PUMPS’ START-UP IN LOW AMBIENT TEMPERATURES
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of increase of resistance of cold oil flow in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublicationThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Determination of ability of machines with hydraulic drive during start-up in low ambient temperatures
PublicationW artykule przedstawiono sposoby określania zdatności maszyn z napędem hydraulicznym podczas rozruchu w niskich temperaturach otoczenia. Przedstawiono wyniki badań eksperymentalnych i symulacji komputerowej nagrzewania się układów maszyny roboczych i zespołów hydraulicznych podczas rozruchu w warunkach szoku termicznego.
-
Chapter 15 : Methods of determination of correct operation area for hydraulic component in low ambient temperatures
PublicationW artykule przedstawiono wyniki badań eksperymentalnych zespołów hydraulicznych: silników satelitowych, silników orbitalnych, pomp i silników zębatych, rozdzielaczy suwakowych w tym proporcjonalnych, pomp tłoczkowych, siłowników w warunkach szoku termicznego w celu określenia obszarów parametrów prawidłowego i nieprawidłowego rozruchu nie tylko tych badanych zespołów. Została stworzona baza danych z wartościami współczynników...
-
Cold Start Emissions of Spark-Ignition Engines at Low Ambient Temperatures as an Air Quality Risk
Publication -
Excess Emissions and Fuel Consumption of Modern Spark Ignition Passenger Cars at Low Ambient Temperatures
Publication -
Problems of the starting and operating of hydraulic components and systems in low ambient temperature. Part III.Methods of determining parameters for correct start-ups of hydraulic components and systems in low ambient temperatures
PublicationW artykule przedstawiono metody: eksperymentalną, analityczną i symulacji komputerowej określania zdatności oziębionych zespołów hydraulicznych do pracy w warunkach zasilania gorącym czynnikiem roboczym powodujących tzw. szok termiczny.
-
PROBLEMS OF THE STARTING AND OPERATING OF HYDRAULIC COMPONENTS AND SYSTEMS IN LOW AMBIENT TEMPERATURE (PART V) METHODS ENSURING CORRECT START-UP OF HYDRAULIC COMPONENTS OF SHIP’S ONBOARD DEVICES IN LOW AMBIENT TEMPERATURES
PublicationA large number of hydraulic devices and systems are started in low ambient temperatures. A good example of such a device is the hoisting winch on the ship. Starting hydraulic drive units in thermal shock conditions (rapid supply of hot oil to the cold unit) may lead to incorrect operation of the actuating system, for instance, due to the loss of clearance between cooperating elements. The article presents methods to prevent the...
-
Effects of Ni-NCAL and Ni–Ag electrodes on the cell performances of low-temperature solid oxide fuel cells with Sm0.2Ce0·8O2-δ electrolyte at various temperatures
PublicationThree low-temperature solid oxide fuel cells are built using Sm0.2Ce0·8O2-δ (SDC) as the electrolyte. Cell A is symmetrical and features Ni–LiNi0.8Co0·15Al0·05O2 (Ni–NCAL) electrodes, Cell B comprises a Ni–NCAL anode and a Ni–Ag cathode, and Cell C is fabricated using a Ni–NCAL cathode and a Ni–Ag anode. The ohmic resistance and polarization resistance (Rp) of Cells B and C are significantly higher than those of Cell A. The reduction...
-
Research of hydraulic axial piston pump at low ambient temperatures
Open Research DataPresented data include the results of measurements of oil temperature at the inlet and outlet of the hydraulic pump (theoretical displacement is equal to 16 cm3/rev) , temperature of the heated pump and oil pressure at the inlet and outlet of the pump.
-
Linear impedance of 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated two times measured with impedance spectroscopy method at low temperatures
Open Research DataThe linear electrcial properties of 50(2Bi2O3-V2O5)-50SrB4O7 glass heat treated two times was measured by impedance spectroscopy method.
-
Evaluation of Pavement Temperatures in Poland During Winter Conditions
PublicationThe paper presents the analysis of pavement temperatures from meteorological stations located at the Polish national roads during the impact of low winter temperatures. Presented issue is particularly important in view of the problem of low-temperature cracks that occur in the asphalt pavement under the influence of low temperatures. For each location of meteorological station there were analysed measurements of the temperature...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublicationThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
Jerzy Kowalski dr hab. inż.
People -
Sum of Effective Temperatures in Colorado Beetle Control
Publication -
Characterization of CaWO4 scintillator at room and liquid nitrogen temperatures
Publication -
Study of pure nai at room and liquid nitrogen temperatures
Publication -
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublicationThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel
PublicationThis paper examined the cyclic deformation behaviour of multiphase low-carbon steel that was subjected to austempering heat treatments at four temperatures (190 °C, 230 °C, 275 °C, and 315 °C) below the martensite start temperature (Ms = 353 °C). The tests were conducted at room temperature, under fully reversed strain-controlled conditions, with strain amplitudes in the range 0.5–1.0%. The microstructure was observed by transmission...
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Theoretical prediction of enthalpies and temperatures of sublimation of organochlorine compounds including pesticides
Publication -
Evaluation of porous 430L stainless steel for SOFC operation at intermediate temperatures
PublicationW pracy przedstawiono badania porowatej stali nierdzewnej typu 430L do zastosowań w tlenkowych ogniwach paliwowych jako podłoża. Podłoża były poddawane utlenianiu w powietrzu oraz w wodorze i analizowane z wykorzystaniem mikroskopu elektronowego, dyfrakcji rentgenowskiej i termograwimetrii cyklicznej.
-
Assessment of reformer tubes degradation during longterm service at elevated temperatures
Publication -
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublicationThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Dynamic impedance measurements of the Direct Methanol Fuel Cell cathode at various operating temperatures
PublicationThis article discusses the application of impedance analysis for diagnosing the cathode of a direct methanol fuel cell at various operating temperatures. The Dynamic Electrochemical Impedance Spectroscopy technique coupled with a linear current scan was applied for this purpose. This technique allowed the observation of changes in the cathode's properties in the fuel cell operating under real working conditions. An equivalent model...
-
Low temperature deposition of dense MnCo 2 O 4 protective coatings for steel interconnects of solid oxide cells
PublicationIn this work manganese cobalt spinel (MnCo2O4) coatings were deposited on steel substrates by spray pyrolysis at 390 °C. This is at much lower temperatures than previously reported (typically in excess of 900 °C). It was possible to produce coatings with well controlled thickness (2-5-10 μm). The as-deposited coatings were evaluated for their microstructural changes and electrical conductivity up to 800 °C. Results confirm the...
-
Sliding Wear Performance of AlCrN Coating on TiB2/Ti Composites at High Temperatures
Publication -
Effects of surface texturing and kind of lubricant on the coefficient of friction at ambient and elevated temperatures
Publication -
Crystal structure and low-energy Einstein mode in ErV2Al20 intermetallic cage compound
PublicationSingle crystals of a new ternary aluminide ErV2Al20 were grown using a self-flux method. The crystal structure was determined by powder X-ray diffraction measurements and Rietveld refinement, and physical properties were studied by means of electrical resistivity, magnetic susceptibility and specific heat measurements. These measurements reveal that ErV2Al20 is a Curie-Weiss paramagnet down to 1.95 K with an effective magnetic...
-
Long-Term Stability of Benzodiazepines and Z-Hypnotic Drugs in Blood Samples Stored at Varying Temperatures
PublicationBenzodiazepines (BZDs) and Z-drugs are among the most commonly prescribed pharmaceuticals in the world and are considered standard care for various mental illnesses and for treatment of sleeping and anxiety disorders, alcohol withdrawal, muscle spasms and epilepsy. Some BZDs are not allowed as pharmaceuticals in many countries, and they are used as "designer benzodiazepines" (DBZDs). All these compounds are typically screened in...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublicationBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Highly stable CsFAPbIBr perovskite solar cells with dominant bulk recombination at real operating temperatures
PublicationMixed-cation mixed-halide perovskite solar cells have been characterized in DC at different temperatures (from −20 °C up to 50 °C) and the time evolution of the device efficiency has been assessed using different degradation protocols (indoors and outdoors). The completely planar p–i–n structure is ITO/CuNiOx/PTAA/CsFAPbIBr/PCBM/PEI/Ag. Pristine current–voltage characteristics barely show hysteresis, at any temperature. Open circuit...
-
Energy resolution and non-proportionality of the light yield of pure CsI at liquid nitrogen temperatures
Publication -
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublicationThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Densimetric and ultrasonic characterization of pentaerythritol in water and in aqueous NaCl and MgCl2 solutions at different temperatures
PublicationZmierzono gęstości dla serii roztworów pentaerytritolu w czystej w wodzie jak i w wodnych roztworach NaCl i MgCl2 zawierających stałą ilość soli. Pomiary wykonano dla trzech różnych zawartości NaCl i MgCl2 w sześciu rożnych temperaturch w przedziale od 20oC do 40oC. Ponadto wyznaczono szybkości rozchodzenia się dźwięku w przygotowanych roztworach dla dwóch temperatur (25 i 37oC). W oparciu o uzyskane wielkości obliczono pozorne...
-
Low energy electron attachment to platinum(II) bromide (PtBr2)
PublicationtDissociative electron attachment to PtBr2in the gas phase was studied in the low electron energy rangefrom zero up to 10 eV with an energy resolution of 150 meV. The experiments were carried out using ahemispherical electron monochromator coupled with a quadrupole mass spectrometer and pulse count-ing acquisition system. The only anion observed was Br−. This ion is formed at three resonance electronenergies: 0.4 eV, 1.2 eV and...
-
The effect of long-term service at elevated temperatures on structure and mechanical properties of Cr-Mo-V steel
PublicationPurpose: of this paper is to reveal the microstructural changes in 13HMF steel exposed to long-term service at elevated temperatures. The degradation of bainite structure was determined and carbides morphology has been examined. The influence of carbides evolution was discussed in dependence of creep rupture strength and mechanical properties of the steel.
-
Comparison of calculated and measured thermal stresses in asphalt concrete
PublicationThe paper presents the comparison of calculated and measured thermal stresses induced in restrained asphalt concrete specimens by cooling. Thermal stresses were measured in the Thermal Stress Restrained Specimen Test. The calculations of thermal stresses were performed with the use of a theoretical formula based on the temperature dependent stiffness modulus. The novel approach applied in this paper was that the stiffness modulus...
-
Changes in enzymatic activity of fish and slaughter animals meat after high pressure treatment at subzero temperatures
PublicationThe aim of this study was to determine changes in the activity of proteolytic enzymes and transglutaminase of fish and mammal meat after pressurization at subzero temperatures. The activity was measured at the optimal pHs determined for enzymes from particular types of tested meat. It was found that increasing the pressure in the range of 60–193 MPa, did not change significantly the activity of acidic proteases of cod flesh, while...
-
Tribological synergy between classical ZDDP and innovative MoS2 and MoO3 nanotube additives at elevated temperatures
Publication -
Deviations of treeline Norway spruce radial growth from summer temperatures in East-Central Europe
Publication