Filters
total: 194
filtered: 145
Search results for: KOMPOZYT
-
Processing and properties of Al-Si-Fe-Cr in situ composites
PublicationPraca jest kontynuacją badań nad wytwarzaniem tanich kompozytów in situ o osnowie stopu Al-Si wzmocnionego związkami międzymetalicznymi Al-Fe-Si lub Al-Fe-Cr-Si, otrzymanych poprzez reakcję ciekłego stopu Al (Al-Si11, Al-Si25) z proszkiem Fe lub Cr. Żelazo zostało wybrane ze względu na niską cenę, niską temperaturę wytwarzania, wysoką reaktywność z Al i heksagonalną sieć krystalograficzną związku Al-Fe-Si, co sprzyja tworzeniu...
-
Badanie możliwości stosowania kompozytów popiołowo-cementowych z włóknami szklanymi i stalowymi w warunkach zagrożenia korozją chlorkową.
PublicationCelem pracy jest zbadanie wpływu modyfikacji drobnoziarnistych kompozytów popiołowo-cementowych dodatkiem niewielkich ilości włókienszklanych i stalowych na ich właściwości techniczne i odpornoiść na korozję chlorkową. Ograniczenie ilości cementu oraz zastąpienie znacznej części kruszywa popiołem lotnym i dodatek włókien losowo roproszonych stanowi próbe uzyskania ochrony materiałowo-strukturalnej przed korozją.
-
Wpływ budowy złożonych warstw powierzchniowych i nano-warstw na trwałość kompozytów poliestrowo-szklanych w środowisku wodnym
PublicationModyfikacja nanocząstkami warstw laminatów stosowanych na małe jednostki pływające powinno spowodować korzystne zmiany morfologii mikrostruktury, podwyższyć odporność udarową i zwiększyć odporność na działanie wody. Celem naukowym pracy, dotyczącej degradacji kompozytów polimerowych stosowanych w budowie małych jednostek pływających, była charakterystyka porównawcza materiałów warstwowych aktualnie proponowanych przez przemysł...
-
Fabrication and properties of hybrid SiCp-Cf/Al composite for tribological applications
PublicationPrzedstawiono sposób otrzymywania i właściwości kompozytu o osnowie siluminu AlSi7Mg ze wzmocnieniem cząstkami SiC otrzymywanego przez infiltrację pod ciśnieniem preformy z ciągłych włókien węglowych. Otrzymano znaczne zwiększenie koncentracji SiC (do 45%) w stosunku do kompozytów Al/SiC odlewanych grawitacyjnie (ok 15-25%).
-
Fabrication, microstructure and properties of Al-Si -Fe-Cu in situ composites.
PublicationW poszukiwaniu tanich kompozytów na bazie stopów Al powstała koncepcja otrzymywania kompozytów in situ o osnowie stopu Al-Si w reakcji ciekłego stopu Al-Si (Al-Si11, Al-Si25) z proszkiem Fe. Powstałe wydzielenia np. iglastego AlFe4Si w stopie AlSi25 o niezbyt wysokiej twardości (rys.2) stanowią skuteczne wzmocnienie stopu pod względem twardości, sztywności i wytrzymałości na ściskanie jak też obniżonej ścieralności. Jednak znaczny...
-
PORÓWNANIE ZASTOSOWANIA ZAAWANSOWANEJ TECHNOLOGII WYTWARZANIA KOMPOZYTÓW Z WŁÓKNA WĘGLOWEGO PREPREG I TECHNOLOGII INFUZJI NA MASĘ ELEMENTÓW ORAZ MOŻLIWOŚCI PRODUKCYJNE
PublicationKompozyty z włókna węglowego odgrywają kluczową rolę w wielu gałęziach przemysłu, w tym w motorsporcie, gdzie często stanowią podstawowy element konstrukcji pojazdów. Pozwalają one na osiągnięcie unikalnych właściwości, które są niemożliwe do uzyskania przy użyciu innych materiałów, dzięki możliwości dostosowania wytrzymałości w każdej osi do przewidywanych naprężeń. Technologia wytwarzania kompozytów jest kluczowym czynnikiem...
-
Advanced laminate composites of improved impact tolerance.
PublicationPrzedstawiono przegląd sposobów poprawy tolerancji udarów w nowoczesnych laminatach polimerowych. Są to: wytrzymalsze i bardziej ciągliwe materiały osnowy, dobieranie odpowiedniego powiązania osnowy i włókien, stosowanie włókien w postaci tkanin, zszywanie preform z wielu warstw tkanin, łączenie włókien ciągłych w preformy za pomocą kompozytowych szpilek, stosowanie tkanin NCF z włókien ciągłych łączonych na grubości dodatkowym...
-
Composite (La, Sr)MnO3-YSZ cathode for SOFC
PublicationW pracy przedstawiono właściwości elektryczne kompozytów (La,Sr)MnO3-YSZ. Materiały te dzieki swoim włąściwościom mogą staniwć dobry materiał na katody ogniw paliwowych. Przedstawiono też wyniki badań ogniwa paliwowego pracującego z paliwem wodorowym zbudowanego na bazie katody z kompozytu LSM-YSZ i anody Ni-YSZ. Uzyskano gęstośc mocy 0.26 W cm−2 przy temperaturze 850°C.
-
Morfologia, właściwości mechaniczne oraz palność spienionych materiałów poliuretanowo-poliglicerynowych modyfikowanych grafitem ekspandowanym
PublicationSpienione kompozyty poliuretanowo-glicerynowe modyfikowane grafitem ekspandowanymotrzymano metodą jednostopniową z układu dwukomponentowego, gdzie jako składnik poliolowyzastosowano odpadową poliglicerynę. Scharakteryzowano morfologię, właściwościmechaniczne oraz klasę palności otrzymanych materiałów. Uzyskane wyniki wskazują, żewprowadzenie poligliceryny do matrycy poliuretanowej umożliwia otrzymanie materiałówcharakteryzujących...
-
The effect of low energy impact on the tensile strength of coated and uncoated glass particulate composites.
PublicationPrzedstawiono model teoretyczny pozwalający przewidywać poudarową wytrzymałość na rozciąganie w funkcji parametrów materiałowych i budowy kompozytu. Określono eksperymentalnie poudarową wytrzymałość na ściskanie kompozytów zbrojonych ciągłym włóknem szklanym w osnowie żywicy epoksydowej napełnianej mikrokulkami szklanymi w celu obniżenia skłonności do powstawania dużych zniszczeń przy udarze o niskiej energii. Wyniki eksperymentalnie...
-
Ekspertyza nr WOiO/II/78/2015 n.t. własności mechanicznych laminatów epoksydowo-bazaltowych
PublicationWspółczesne konstrukcje jachtów często wykonywane są z materiałów kompozytowych. Najczęściej stosowane są kompozyty (laminaty), których zbrojenie wykonane jest z włókna szklanego bądź węglowego, przesyconego żywicą (poliestrową, epoksydową, winyloestrową). W przemyśle jachtowym, co raz częściej stosuje się zbrojenia wykonane z włókien bazaltowych. Zleceniodawca dostarczył próbki wykonane z różnych materiałów, w tym m.in ze wspomnianych...
-
Materiały dla jednowarstwowych ogniw paliwowych
PublicationWytworzono materiał kompozytowy metodą syntezy w fazie stałej, który można zastosować do produkcji jednowarstwowego ogniwa paliwowego. Kompozyt składał się z dwóch faz. Pierwszą fazą był nanoceramiczny przewodnik protonowy – niobian lantanu domieszkowany akceptorowo wapniem. Składnikiem drugim był nanoceramiczny tlenek półprzewodzący złożony z tlenków litu, niklu i cynku. Otrzymany materiał zbadano pod kątem właściwości strukturalnych...
-
Badania pękania udarowego w konstrukcjach przekładkowych poliestrowo-szklanych z rdzeniem z pianki PVC
PublicationPorównano podatność do pękania udarowego trzech konstrukcji przekładkowych z okładkami z laminatu poliestrowo-szklanego i rdzeniem z pianki PVC, za pomocą dynamicznych charakterystyk obciążeń/odkształceń oraz badań mikrostrukturalnych. Zastosowano trzy rodzaje spoiwa (Scott Bader) do połączenia okładek z rdzeniem: spoiwo dwufazowe z twardym napełniaczem, spoiwo lekkie z napełniaczem w postaci mikrosfer oraz żywicę poliestrową (przyklejanie...
-
Wpływ obróbki plastycznej powłok kompozytowych Ni-Al-Al2O3 oraz z faz międzymetalicznych Ni3Al i NiAl na parametry krzywej udziału materiałowego
PublicationOkreślono wpływ obróbki plastycznej przez spęczanie na parametry stereometryczne powłok stopowych, kompozytowych oraz z faz międzymetalicznych. Materiał powłokowy został nałożony na podłoże stalowe (C45) za pomocą poddźwiękowego płomieniowego natryskiwania plazmowego.
-
Wpływ obróbki plastycznej powłok MMC na umocnienie i zmniejszenie chropowatości powierzchni
PublicationOkreślono wpływ obróbki plastycznej na wybrane właściwości powłok kompozytowych o osnowie niklowej przy różnym udziale procentowym fazy dyspersyjnej Al2O3. Powłoki Ni-Al-Al2O3 zostały nałożone na próbki ze stali niestopowej C45 z użyciem technologio poddźwiękowego płomieniowego natryskiwania cieplnego. Następnie poddane zostały obróbce plastycznej na zimno i prasowanie na prasie hydraulicznej. W pracy przedstawiono analize wyników...
-
Obróbka wykańczająca powłok MMC w aspekcie umocnienia i zmniejszenia chropowatości powierzchni
PublicationPowłoki natryskiwane cieplnie nakładane są z uwzględnieniem naddatku na obróbkę wykańczającą. Obróbka wykańczająca powinna zapewnić nie tylko odpowiednią grubość powłok związaną z wymiarem nominalnym przedmiotu ale również uzyskanie wymaganej chropowatości i falistości powierzchni. Najczęściej w tym celu stosuje się obróbkę wiórową, rzadziej szlifowanie. Ze względu na dużą chropowatość powłok kompozytowych o osnowie metalowej...
-
Environmental stress cracking in e-glass and aramid/glass epoxy composites
PublicationKompozyty epoksydowe wzmocnione włóknami szklanymi są dość odporne na wpływy środowiskowe w stanie nieobciążonym, jednak po przyłożeniu obciążeń łatwo pękają w środowisku wody i rozcieńczonych kwasów. Charakterystyki propagacji pęknięć środowiskowych w laminatach szklano/epoksydowych były przedmiotem szeregu prac, jednak brak jest danych na temat zachowania laminatów o wzmocnieniu hybrydowym aramidowo-szklanym stosowanych w budowie...
-
Wpływ absorpcji wody na własności laminatów winyloestrowych wzmocnionych włóknem aramidowym i szklanym
PublicationZbadano zachowanie dwóch laminatów o osnowie winyloestrowej, zbrojonych włóknami aramidowymi i szklanymi w stanie suchym i po zanurzeniu w wodzie. Materiały poddawane są badaniom ze względu na potencjalne zastosowanie w okrętownictwie i brak podobnych danych w literaturze. Zbrojenie laminatów miało postać tkaniny hybrydowej aramidowo szklanej (1) lub składało się z na przemian ułożonych jednorodnych warstw włókien aramidowych i...
-
Wpływ rodzaju zbrojenia i kolejności ułożenia warstw na tolerancję zniszczeń wywołanych udarami o małej prędkości z laminatów epoksydowych zbrojonych włóknem węglowym, szklanym, Kevlarowym i hybrydowych
PublicationPorównano zachowanie pod obciążeniem statycznym i udarowym laminatów epoksydowych zbrojonych tkaniną węglową lub szklaną z właściwościami laminatów hybrydowych zawierających zarówno zbrojenia szklane jak i węglowe w różnej ilości i układzie geometrycznym.
-
Badanie wpływu parametrów technologii wtryskiwania na wybrane właściwości mechaniczne kompozytu poliamidowego napełnionego cząstkami niejednorodnego recyklatu.**2003, 200 s. 68 rys. 18 tab. bibliogr. 74 poz. maszyn. Rozprawa doktorska /03.12.2003/. PG, Wydz. Mechaniczny. Promotor: prof. dr inż. W. Przybylski.
Publication.
-
Modification of cement-ash composites with steel fibre addition
PublicationPraca zawiera wyniki badań kompozytów cementowo-popiołowych, w których popiół zastosowano jako częściowy zamiennik cementu. Do kompozytów dodano niewielkie ilości dwóch rodzajów włókien stalowych. Zbadano właściwości techniczne kompozytów. Wytrzymałości kompozytów cementowo-popiołowych z włóknami stalowymi w stosunku do wytrzymałości kompozytów bez włókien po wszystkich okresach wiązania i twardnienia były wyższe od kilku do kilkudziesięciu...
-
Analiza eksperymentalna i numeryczna kompozytowych płyt warstwowych
PublicationPłyta warstwowa jest kompozytem o bardzo atrakcyjnych właściwościach - dzięki swojej budowie jest elementem jednocześnie wytrzymałym i lekkim. Idea pozwalająca na osiągnięcie tych własności bazuje na współpracy materiałów o różnych parametrach wytrzymałościowych, co prowadzi jednocześnie do pewnych trudności w analizie i projektowaniu. Celem niniejszej pracy jest lepsze poznanie zachowania płyty warstwowej z okładzinami z płyty...
-
Low-temperature processed anode for Solid Oxide Fuel Cells
PublicationPrzygotowano i przebadano kompozytową anode Ni/YSZ, która została przygotowana z wykorzystaniem technologii net shape. Wyniki potwierdziły, że kompozyt może być wykorzystany jako potencjalna anoda w tlenkowych ogniwach paliwowych.
-
Projektowanie, synteza i charakterystyka fotokatalizatorów nowej generacji na bazie związku Ti3C2Tx do usuwania aktywnych substancji farmaceutycznych
PublicationCelem niniejszej pracy było zastosowanie materiałów nowej generacji na bazie związku Ti3C2Tx w procesach fotokatalitycznej degradacji aktywnych substancji farmaceutycznych: karbamazepiny, acetaminofenu i ibuprofenu. Zakres prac badawczych obejmował syntezę fotokatalizatorów, charakterystykę ich właściwości fizykochemicznych, oraz ocenę aktywności fotokatalitycznej. Przedstawiono możliwość zastosowania węglika tytanu jako kokatalizatora...
-
Role of reciprocating sliding testing in tribological materials engineering
PublicationPrzedstawiono wyniki badań oporu ruchu i zużycia skojarzeń o styku rozłożonym przy posuwisto-zwrotnym ślizganiu. Badano skojarzenia: żeliwo-stop aluminium przetapiany laserowo w warunkach kriogenicznych oraz żeliwo-kompozyt aluminium-żelazo otrzymany ''in situ''.
-
Właściwości elektryczne szkło-ceramiki zawierającej ferroelektryczną fazę BiV
PublicationKompozyty szklano - ceramiczne zawierające nanokryształy posiadają właściwości fizyczne, które nie są możliwe do uzyskania w innych materiałach. Dzięki możliwości wytworzenia szkło - ceramik posiadających kryształy o różnej wielkości (nano, mikro...) i różnorodnego typu, można w istotny sposób kontrolować właściwości elektryczne takich materiałów. Stała dielektryczna faz ferroelektrycznych jest bardzo wrażliwa na zmiany rozmiarów...
-
Ziarna i mikroziarna diamentowe. Rodzaje ścierniw i przykłady zastosowania
PublicationW książce zawarto podstawowe informacje technologiczne i wyniki prac nad ziarnami i mikroziarnami diamentowymi. Przedstawiono właściwości mechaniczne, termiczne, chemiczne, magnetyczne, elektryczne i optyczne diamentu. Omówiono pochodzenie diamentów, charakteryzując diamenty naturalne oraz wytwarzane w statycznych warunkach wysokiego ciśnienia i temperatury oraz w warunkach dynamicznych. Scharakteryzowano diamentowe kompozyty polikrystaliczne,...
-
Łożyska ślizgowe smarowane wodą
PublicationŁożyska ślizgowe smarowane wodą wykonywane są obecnie z kompozytów polimerowych, kompozytów gumowych, kompozytów metalowych i ceramiki. Najczęściej z kompozytów polimerowych, przy czym znacznie rośnie udział materiałów ceramicznych. Przedstawiono przegląd konstrukcji łożysk ślizgowych smarowanych wodą i rodzajów stosowanych przez światowe firmy materiałów na łożyska. Opisano unikatowe rozwiązanie konstrukcyjne poprzecznego, klockowego...
-
The investigation of polyester composites filled by modified bentonite
PublicationPraca dotyczy zagospodarowania odpadów poliestrowo-szklanych przez wytworzenie kompozytów z ich użyciem oraz żywicy poliestrowej, mączki dolomitowej i nanonapełniacza. Wykazano, ze dodatek 2% nanonapełniacza do do kompozytów poliestrowych zawierających 15% masowych odpadów pozwala na uzyskanie materiału wykazującego korzystne właściwości wytrzymałościowe. Proponowany sposób modyfikacji kompozytów poliestrowych jest nowym rozwiązaniem...
-
Estimation of the expected effects of different surface modifications on mechanical, chemical and biological behaviour of endoprostheses
PublicationPrzedstawiono koncepcję nowej endoprotezy o szczególnie wysokiej odporności na zużycie i pękanie. Koncepcja zakada wytwarzanie wieloetapową obróbkę powierzchniową kompozytu metalowo-ceramicznego.
-
Detekcja uszkodzeń w kratownicy kompozytowej z zastosowaniem sprzężonych fal gietno-ścinających.
PublicationPrzedstawiono model spektralny belki kompozytowej z pęknięciem. Zbadano wpływ wymiarów uszkodzenia i parametrów materiałowych kompozytu na zmiany w propagujacej sie fali gietno-ścinającej.
-
Identyfikacja parametrów wytrzymałościowych gruntu.
PublicationW pracy przedstawiono wyniki badań deformacji objętościowych gruntów antropogenicznych (kompozytów iłowo - popiołowych) w wyniku wzrostu wilgotności. Zastosowano metodę obciążania po nasyceniu oraz metodę obciążenie - nasycenie - obciążenie, Stwierdzono wyraźną zależność rodzaju i wartości deformacji od składu kompozytów oraz wskazano na istotny wpływ metody badania.
-
Wpływ absorpcji wody na obrazy zniszczeń udarowych w wybranych warstwowych kompozytach polimerowych
PublicationPrzedstawiono obrazy zniszczeń udarowych (zewnętrznych i wewnętrznych) w płytkach kompozytu epoksydowego o zbrojeniu hybrydowym aramidowo-szklanym w stanie suchym i po nasyceniu wodą. Przy małej energii udaru (ok. 5 J/mm) zniszczenia sprowadzają się do lekkich uszkodzeń powierzchni w miejscu uderzenia bijaka oraz delaminacji i pęknięć na granicy włókien i osnowy spowodowanych oddzielaniem składników kompozytu na skutek absorpcji...
-
Synteza i właściwości jonowoprzewodzących materiałów poliuretanowych
PublicationPrzewodzące kompozyty poliuretanowe otrzymywano w syntezie dwuetapowej. W pierwszym etapie syntetyzowano prepolimer uretanowy. W tym celu poddawano reakcji 4,4'-diizocyjanianu difenylometanu (MDI) oraz oligoeterol ( PTMG 1000, PTMG 2000 lub Rokopol D-2002). W drugim etapie jako przedłużacz łańcuchów stosowano 1,4-butanodiol (BDO). Elastomery te były domieszkowane solami LiClO4 lub LiCl oraz modyfikowane montmorylonitem. Domieszkowanie...
-
Characteristics of the conductivity of polyurethane nanocomposite
PublicationW opracowaniu tym przedstawiono właściwości mechaniczne oraz przewodnictwo jonowe otrzymanych nanokompozytów poliuretanowych. KOmpozyty te były otrzymane przy wykorzystaniu wytłaczarki dwuślimakowej. POddano je badaniom wytrzymałościowym, spektroskopii impedancyjnej, spektroskopii w podczerwieni oraz badaniom dynamiczno - mechanicznym (DMA)
-
New ceramic and composite tools for smoothing burnishing process
PublicationW pracy przedstawiono nowe konstrukcje narzędzi ceramicznych i z kompozytu karbonado do nagniatania twardych hartowanych stali. Zamieszczono wyniki badań wpływu parametrów technologicznych nagniatania walcowych próbek ze stali 45 o różnej twardości 23-56HRC na chropowatość powierzchni próbek.
-
Badania wpływu nieorganicznych napełniaczy proszkowych na właściwości polipropylenu
PublicationOmówiono sposób wytwarzania tworzyw polimerowych zawierających nieorganiczne napełniacze proszkowe. Podczas badań jako matrycę polimerową zastosowano polipropylen, który napełniano talkiem, kredą oraz ich mieszaniną. Próbki kompozytów na bazie polipropylenu otrzymywano stosując wytłaczarkę dwuślimakową współbieżną. Temperatura stref grzewczo-chłodzących cylindra wytłaczarki oraz temperatura głowicy wynosiła 195°C. Scharakteryzowano...
-
Application of ceramic and composite tools in smoothing burnishing process.
PublicationArtykuł zawiera oryginalne konstrukcje narzędzi nagniatających. Elementy nagniatające zostały wykonane z ceramiki i kompozytu ''Karbonado''. Narzędzia te mogą być stosowane na obrabiarkach CNC i centrach obróbkowych, zwłaszcza do obróbki stali hartowanych. Artykuł przedstawia również wyniki badań i przykłady zastosowań tych narzędzi w przemyśle.
-
Structural studies and melting of bismuth nanocrystals in reduced bismuthgermanate and bismuth silicate glasses.
PublicationOtrzymano nanostruktury krystalicznego bizmutu w matrycy XO2 (X=Si,Ge) oraz warstwę nanostruktur krystalicznego bizmutu na powierzchni redukowanych w atmosferze wodoru szkieł Bi0.33Ge0.67O1.84 i Bi0.57Si0.43O1.72. Kompozyt Bi-szkło badano metodą DSC, XRD oraz AFM. Zaobserwowano zmniejszenie temperatury topnienia nanokrystalicznego bizmutu znajdującego się w matrycy szkła z 544 K do 387 K oraz do 502 K w przypadku powierzchniowej...
-
Conducting composites as cable anodes in cathodic protection
PublicationOpisano zasadę działania oraz podstawowe parametry charakteryzujące układ anodowy z wykorzystaniem anod kablowych w systemie ochrony katodowej podziemnych konstrukcji. W tej metodzie ochrony jako materiał anodowy wykorzystywany jest kompozyt przewodzący, którego właściwości mechaniczne umożliwiają budowę anody w formie kabla biegnącego wzdłuż trasy konstrukcji podziemnej. Wykazano, że zawartość grafitu w elektrodzie kompozytowej...
-
The effect of water immersion ageing on low-velocity impact behaviour of woven aramid-glass fibre/epoxy composites.
PublicationPorównano dynamiczne przebiegi obciążeń i odkształceń w próbie udarowej ze spadajacą masą dla płytek z kompozytu epoksydowego zbrojonego tkaniną hybrydową aramidowo szklaną lub warstwami tkanin aramidowej i szklanej w stanie suchym i po ekspozycji w wodzie. Wyniki eksperymentalne porównano z przewidywniami teoretycznymi. Uzyskano dobrą zgodność.
-
Conducting composites as cable anodes in cathodic protection: a literature summary
PublicationPrzedstawiono podstawową charakterystykę systemu ochrony katodowej z wykorzystaniem anod kablowych. Anody kablowe różnią się od klasycznych systemów anodowych sposobem instalacji anod. System anodowy oparty na anodach kablowych nie jest instalowany punktowo; anoda umieszczana jest w niewielkiej odległości od chronionej konstrukcji i biegnie wzdłuż trasy konstrukcji. Materiałem anodowym proponowanego rozwiązania jest elastyczny...
-
Modyfikacja właściwości trybologicznych poliuretanów
PublicationPrzedstawiono metody modyfikacji właściwości trybologicznych poliuretanów i kompozytów poliuretanowych oraz metody badań tych właściwości. Porównano materiały pod względem odporności na zużycie i ścieranie.
-
Silicatization of fly ashes a harmless way of the wastes utilization.
PublicationArtykuł przedstawia osiągnięcia w pracach nad wykorzystaniem popiołów lotnych do formowania nowego materiału budowlanego, nazwanego kompozytem krzemianowo-popiołowym. Przedstawiono charakterystykę fizyko-mechaniczną omawianego materiału.
-
Microstructure and electrical properties of SrTi0.98Nb0.02O3-δ-based composites applied as porous layers for SOFCs
PublicationPrzebadano właściwości elektryczne oraz strukturalne kompozytów Sr(Ti,Nb)O3-YSZ i Sr(Ti,Nb)O3-CeO2 naniesionych w postaci warstw porowatych na podłoża YSZ
-
The comparison of SrTi0.98Nb0.02O3-δ-CeO2 and SrTi0.98Nb0.02O3-δ-YSZ composites for use in SOFC anodes
PublicationWytworzono i przebadano właściwości strukturalne i elektryczne kompozytów SrTi0.98Nb0.02O3-δ-CeO2 i SrTi0.98Nb0.02O3-δ-YSZ. Przeprowadzono testy materiałów zastosowanych jako anody w tlenkowych ogniwach paliwowych.
-
Wpływ rozcieńczalnika reaktywnego na reologiczne i mechaniczne właściwości żywic epoksydowych
PublicationW pracy przedstawiono wyniki badań nad wpływem reaktywnych rozcieńczalników na reologiczne i mechaniczne właściwości żywic epoksydowych. Przeprowadzono badania udarności, odporności na zginanie, twardości oraz oznaczono temperaturę zeszklenia otrzymanych kompozytów w zależności od rozcieńczalnika.
-
Geosynthetics tests in hydrotechnical structures design
PublicationW celu właściwego stosowania w konstrukcjach budowlanych (w tym również hydrotechnicznych)geosyntetyków - zarówno przepuszczalnych (geotekstylia i wyroby pokrewne) jak i nieprzepuszaczalnych (geomembrany i kompozyty uszczelniające), bardzo ważne jest wcześniejsze poddawanie go odpowiednim badaniom, których procedura musi być ściśle powiązana z późniejszym przeznaczeniem geomateriału i uwzględniać warunki, w jakich materiał będzie...
-
Materiały stosowane do wytwarzania implantów kości
PublicationMateriały stosowane do wytwarzania implantów kostnych muszą być biokompatybilne, nietoksyczne, bioaktywne oraz wykazywać odpowiednie właściwości mechaniczne, takie jak wytrzymałość na ściskanie, na zginanie oraz sztywność i twardość. Gama stosowanych materiałów jest bardzo szeroka, obejmuje metale, polimery, ceramikę oraz ich kompozyty. Każdy z tych materiałów ma swoje mocne i słabe strony. Praca stanowi przegląd materiałów stosowanych...
-
The influence of preparing conditions on the properties of SrTi0.98Nb0.02O3-YSZ composite
PublicationZbadano wpływ warunków przygotowania na właściwości kompozytów SrTi0.98Nb0.02O3-YSZ jako potencjalnych warstw przejściowych między anodą a elektrolitem w tlenkowych ogniwach paliwowych SOFC. Udowodniono, że proces wstępnej obróbki temperaturowej substratów oraz sposób ich mielenia znacznie wpływa na przewodnictwo elektryczne badanych materiałów.