Filters
total: 11557
filtered: 10292
-
Catalog
- Publications 10292 available results
- Journals 23 available results
- Conferences 21 available results
- People 175 available results
- Inventions 2 available results
- Projects 50 available results
- Laboratories 5 available results
- Research Teams 13 available results
- Research Equipment 9 available results
- e-Learning Courses 369 available results
- Events 25 available results
- Offers 1 available results
- Open Research Data 572 available results
Chosen catalog filters
displaying 1000 best results Help
Search results for: SGS MODEL
-
Badania eksperymentalne modelu zbiornika stalowego na stole sejsmicznym = Experimental study on steel tank model using shaking table
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is really crucial because any failure may have serious consequences. Earthquakes are the most dangerous and also the most unpredictable dynamic loads acting on such structures. On the other hand, rockburst-induced ground motions are usually considered to be less severe due to lower...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
3D Model Preparing Patterns for Interactive Urban Visualization - Guidelines for Graphic Designers Preparing 3D Models for Virtual Reality Applications
PublicationWhile working on architectural visualizations, the software developer often has to work with graphic designers who create models in a different environment what can cause many complications. For this reason, it is very important to have some guidelines which can protect both the developer and the designer from commixing mistakes. The paper presents a list of such guidelines based on the authors’ experience. The reader can treat...
-
Model-free and Model-based Reinforcement Learning, the Intersection of Learning and Planning
PublicationMy doctoral dissertation is intended as the compound of four publications considering: structure and randomness in planning and reinforcement learning, continuous control with ensemble deep deterministic policy gradients, toddler-inspired active representation learning, and large-scale deep reinforcement learning costs.
-
Model negocjacji internetowych
PublicationArtykuł prezentuje wyniki badań dotyczących przebiegu i skuteczności negocjacji prowadzonych za pośredictwem internetu. Przedstawione wnioski, opare o przeprowadzony eksperyment, wskazują na wpływ nowoczesnych technologii na osłabienie znaczenia kontekstu społecznego negocjacji, co skutkuje wysoką rywalizacyjnością stylu rokowań, znacznym przedłużaniem się czasu spotkania oraz obniżeniem się satysfakcji z prowadzonych rozmów.
-
Core-Periphery Model
Publication -
Etyczny model decyzyjny
PublicationW artykule usiłowałem przedstawić E. Sternberg koncepcję etycznego modelu decyzyjnego w korespondencji do zagadnienia ochrony środowiska naturalnego. Jest on (jako EMD) charakteryzowany wedle czterech kroków zaproponowanych przez E. Sternberg. Otóż w pierwszym kroku, "przedsiębiorstwo powinno odpowiedzieć sobie na pytanie" jakie zostały przedsiębrane działania w sprawie ochrony środowiska naturalnego. Następnie,...
-
Aproksymacyjny model tarcia
PublicationW pracy przedstawiono problem aproksymacji danych pomiarowych z eksperymentu tribologicznego. W celu uzyskania opisu zależności współczynnika tarcia od liniowej prędkości ślizgania i nacisków zastosowano dwa podejścia: aproksymacja wielomianowa i wykorzystanie sztucznej sieci neuronowej. W rezultacie prowadzonych prac ustalono, podejście neuronowe jest korzystniejsze.
-
Model systemu kształcenia
PublicationRozdział zawiera opis modelusystemu kształcenia ustawicznego, który jest trwałym rezultatem projektu Mayday.
-
A Quality Model for UML tools
PublicationJakość narzędzi UML wpływa na efektywność wykonywania zadań związanych z modelowaniem systemów w procesie wytwarzania oprogramowania. Celem badań prezentowanych w tym referacie jest wyodrębnienie kryteriów jakości narzędzi UML. Omówiono rolę narzędzi UML w projekcie informatycznym, a następnie zaprezentowano szereg kryteriów jakości narzędzi UML wraz z aspektami oceny oraz opisem ankiety, która służy do oceny narzędzi względem...
-
Reduced model of gyroscopic system
PublicationThe paper presents the method of model reduction for the system with gyroscopic interactions. Two methods were used to obtain the approximate discrete models of the continuous structure: the modal decomposition method and the rigid finite element method. The first approach is used for this part of a system for which it is easy to formulate orthogonality conditions, meanwhile the second one is used for other part. The method enables...
-
The elasto-viscoplstic Chaboche model
PublicationW artykule przedstawiono rozwoj i numeryczną aplikacje sprężysto-lepkoplastycznego modelu Chabocha. Przedstawione są także szczegółowe opisy kilkunastu wariantów modelu Chaboche'a wraz z parametrami materiałowymi.
-
Wykorzystanie modelu silnika indukcyjnego klatkowego do prądowej diagnostyki jego łożysk. Application of induction machine model for current diagnostics of bearings
PublicationW pracy podano widmo prądu stojana dla silnika normalnego oraz wprawianego w drgania o nastawianej częstotliwości. Drgania korpusu wirnika skutkują uginaniem się wirnika, co symuluje bicie wirnika od uszkodzenia łożysk. Podano też model matematyczny silnika, dopuszczający niecentryczność wirnika. Podano widmo prądu stojana przy pracy z wibracjami wirnika odwzorowującymi w pewnym przybliżeniu wibracje od uszkodzonych łożysk.
-
Nieliniowe modelowanie odpowiedzi odłącznika wysokiego napięcia SGF 123 podczas trzęsienia ziemi
PublicationSprawność elementów sieci energetycznej, w tym odłączników wysokiego napięcia, jest istotnym elementem zapewnienia bezpieczeństwa na terenie dotkniętym trzęsieniem ziemi. W niniejszym artykule analizie sejsmicznej poddano model odłącznika dwukolumnowego obrotowego SGF 123 produkowany w Polsce. W pierwszym etapie wykonano analizę modalną celem weryfikacji modelu numerycznego. Następnie przeprowadzono szczegółową analizę dynamiczną...
-
JOINT ANALYSIS OF NATIONAL ECO-EFFICIENCY, ECO-INNOVATION AND SDGS IN EUROPE: DEA APPROACH
Publication -
Joint Analysis of National Eco-Efficiency, Eco-Innovation and SDGs in Europe: DEA Approach
PublicationThe growing complexity and intertwining of different socio-economic issues both in individual countries and internationally mean that single-theme analyses do not consider all the relationships and thus have cognitive limitations. Therefore, studies that combine several research areas are increasingly common in the literature to clarify the connections and relationships. In this study, considering the sequential nature of the...
-
The European Union Development Policy and Achieving Sustainable Development Goals (SDGs) of the United Nations
Publication -
Obliczanie wartości PFD dla funkcji bezpieczeństwa obwodu SIS o różnych konfiguracjach.
PublicationPrzedstawiono sposoby wyznaczania wartości średnich PFD, PFDavg, dla funkcji bezpieczeństwa obwodu SIS o różnych konfiguracjach. Określono podstawowe definicje i cel obliczania wartości prawdopodobieństwa niezadziałania funkcji bezpieczeństwa obwodu SIS. Zaprezentowano podstawy teoretyczne obliczeń wartości PFD, PFDavg dla funkcji bezpieczeństwa o różnych konfiguracjach oraz ich modele probabilistyczne. Przedstawiono także przykłady...
-
SDGs implementation, their synergies, and trade-offs in EU countries – Sensitivity analysis-based approach
PublicationSustainable development is one of the most urgent challenges facing humanity. Its basic principle is to improve people’s well-being and maintain it over time. In 2015, the United Nations approved 17 sustainable development goals (SDGs) to ensure a better and sustainable future for all, balancing economic, social and environmental development. SDGs create an ‘indivisible whole’; thus, examining their interactions is crucial. Our...
-
A Pilot Study on Machining Difficult-to-Cut Materials with the Use of Tools Fabricated by SLS Technology
PublicationThe growing use of contemporary materials in various industrial sectors, such as aerospace, automotive, as well as the oil and gas industry, requires appropriate machining methods and tools. Currently, apart from the necessity to obtain high-dimensional and shape accuracy, the efficiency and economic aspects of the selected manufacturing process are equally important, especially when difficult-to-cut materials, such as hard and...
-
Navigational decision support system during approach manoeuvre in emergency STS transfer operation
PublicationThe paper is concerned with the problem of safe trajectory planning for approaching during emergency STS (Ship to Ship) transfer operation with oil spill. The safe trajectory means that the way points does not cross in the area of the environment with the static and dynamic obstacles and at the same time satisfies ship's stopping and speed deceleration performance. The evolutionary path planning algorithm is used to determine trajectory...
-
Electrical conductivity of nanostructured acceptor-doped ceria fabricated by spark plasma sintering (SPS)
PublicationHigh purity nanoscale powders (~10–15 nm size) of two different compositions of ceria, doped with Gd3+ and Ca2+, have been consolidated by spark plasma sintering (SPS) at different temperatures. Fully-dense samples were observed only at a sintering temperature of 980 °C. The as-sintered samples showed rather fast grain growth with an average grain size below 300 nm. The electrical properties of the samples were evaluated by impedance...
-
Comparison of continuous and discontinuous constitutive models to simulate concrete behaviour under mixed mode failure conditions
PublicationW artykule porównano modele MES ciągłe i nieciągłe do symulacji zachowania betonu w warunkach mieszanego zniszczenia. W ramach modeli ciągłych zastosowano modele sprężysto-plastyczne oraz modele z redukcją sztywności sprężystej i nielokalnym osłabieniem. W ramach modeli nieciągłych zastosowano XFEM. Przedmiotem obliczeń były strefy lokalizacji i rysy w warunkach mieszanego zniszczenia wg testu doświadczalnego Nooru-Mohameda.
-
FE-modelling of concrete behaviour under mixed mode conditions with non-local and cohesive constitutive models.
PublicationW artykule przedstawiono wyniki symulacji rys zaokrąglonych w elementach betonowych w warunkach mieszanego sposobu obciążenia. Symulacje wykonano przy zastosowaniu modelu rys kohezyjnych i modeli mechaniki ośrodka ciągłego z nielokalnym osłabieniem.. Wyniki symulacji porównano z doświadczeniami.
-
Verification of the Analytical Traffic Model of a Multidomain IMS/NGN Using the Simulation Model
PublicationIn this paper we verify the previously proposed analytical traffic model of a multidomain Next Generation Network (NGN), which is standardized for delivering multimedia services based on the IP Multimedia Subsystem (IMS). For this reason a proper simulation model used, in which not theoretical queuing system models but the operation of real network elements and standardized call scenarios are accurately implemented. Consequently,...
-
Wieloźródłowy model pola elektrycznego okrętu = Multisource model of ship electric field
PublicationW pracy przedstawiono wieloźródłowy model pola elektrycznego okrętu. Wieloźródłowy model stanowi układ źródeł prądowych o określonych położeniach.
-
Experimental Validation of Numerical Model within a Flow Configuration of the Model Kaplan Turbine
PublicationThis paper investigates validation of flow within a model Kaplan turbine. This includes comparison of various turbulence models and their influence on torque and power generated by the turbine. Numerical results were compared with experimental data.
-
The extended model predictive-sliding mode control of three-level AC/DC power converters with output voltage and load resistance variations
Publication -
Wpływ założeń modelu obliczeniowego na wyniki obliczeń hydrodynamicznych łożysk wzdłużnych = The influence of model simplifications on the predicted performance of hydrodynamic thrust bearings
PublicationPrzedstawiono porównanie wyników obliczeń hydrodynamicznych łożysk wzdłużnych otrzymanych z wykorzystaniem dwóch niezależnie opracowanych modeli obliczeniowych TEHD (termoelastohydrodynamicznych). Wykorzystane w obliczeniach programy różnią się głównie założeniami i uproszczeniami przyjętymi, zwłaszcza w odniesieniu do części przepływowej zadania. Symulacje obliczeniowe przeprowadzono stosując w przypadku obu modeli te same warunki...
-
Extension of the force-matching method to coarse-grained models with axially symmetric sites to produce transferable force fields: Application to the UNRES model of proteins
Publication -
Model prędkości radialnej w separatorze wirowym = Radial velocity model in rotational separator
PublicationOmówiono rodzaje separatorów wirowych i wskazano na problemy pojawiające się przy ich wymiarowaniu. Zaproponowano model prędkości radialnej, bazujący na bilansie masy oraz na przeprowadzonych pomiarach czasu przepływu cieczy przez obiekt, stanowiący podstawę dalszych oprac nad metodą wymiarowania separatorów.
-
Comparison of properties of the new electro-mechanical model and circumferential model of the inductive-dynamic drive
PublicationThe article presents a new electromechanical model of inductive-dynamic drive. The model is implemented in two environments: Maxwell for analyzing electrodynamic phenomena including moving of the disc and Ansys which allows for stress analysis on the basis of the volume forces imported from Maxwell. Additionally, a model validation by comparing with the existing circumferential model was carried out.
-
Analiza numeryczna zachowania się odłącznika wysokiego napięcia SGF 245 poddanego obciążeniom sejsmicznym
PublicationPrzedstawiono wyniki analizy numerycznej zachowania się odłącznika wysokiego napięcia SGF 245 podczas trzęsienia ziemi. W analizie zastosowano model odłącznika zaimplementowany w programie MES. W pierwszym etapie wykonano analizę modalną w celu weryfikacji dokładności modelu numerycznego. Następnie przeprowadzono dokładną nieliniową analizę dynamiczną przy wystąpieniu wymuszenia opisanego składową NS trzęsienia ziemi El Centro...
-
Spectroscopic properties of high-temperature sintered SrS:0.05%Ce3+ under high hydrostatic pressure
Publication -
Ocena właściwości niskotemperaturowych mieszanek mineralno-asfaltowych z asfaltem modyfikowanym SBS i gumą
PublicationW artykule przedstawiono wyniki badań przeprowadzonych w niskich temperaturach dla mieszanek mineralno-asfaltowych zaprojektowanych z użyciem asfaltów modyfikowanych miałem gumowym oraz polimerem SBS. Badania laboratoryjne zostały przeprowadzone dla dwóch rodzajów mieszanek mineralno-asfaltowych do warstwy ścieralnej – mastyksu grysowego (SMA 8) i asfaltu porowatego (PA 8). W niniejszym artykule przedstawiono wyniki następujących...
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublicationFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublicationFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
EVALUATION OF THE NO2CONCENTRATION PREDICTION POSSIBILITYBASED ON STATIC AND DYNAMIC RESPONSES OF TGS SENSORSAT CHANGING HUMIDITY LEVELS
PublicationThe commercially available metal-oxide TGS sensors are widely used in many applications due to thefact that they are inexpensive and considered to be reliable. However, they are partially selective and theirresponses are influenced by various factors,e.g. temperature or humidity level. Therefore, it is importanttodesign a proper analysis system of the sensor responses. In this paper, the results of examinations of eightcommercial...
-
Reliability model of the crankshaft-piston assembly
PublicationThe laws that govern the durability of crankshaft-piston assembly friction nodes can be proved or at least derived or justified in an intuitive way. Operation of all the friction nodes is disturbed by external factors occurring with randomly changing intensity and also appearing at random. As the crankshaft-piston assembly friction nodes have a series structure and effects of those disturbances accumulate, their fitness for use...
-
A simple model of circular hydraulic pump
PublicationRozpatrzono warunki powstawania osiowosymetrycznego uskoku hydraulicznego. Przedstawiono model, w którym rozpatrzono obecność dodatkowych strat w równaniu Bernoulliego. Przyczyniają się one do powstawania dodatkowego wiru w miejscu uskoku. Porównanie z wynikami badań eksperymentalnych potwierdza słuszność przyjętych tez.
-
Update a simple hypoplastic constitutive model
PublicationW artykule omówiono uproszczona formę hipoplastycznego konstytutywnego prawa materiałowego do opisu zachowania się materiałów granulowanych. Wykonano symulacje testów elementów i porównano wyniki z doświadczeniami.
-
Numerical Model of Femur Part
PublicationThe aim of the study is to create a new more accurate method of femur part modelling by using the finite element method. According to this new method, a femur part is treated as a complex structure composed of trabecular bone (internal part) and cortical bone (external part). The internal part is modelled as a scaffold, thus the external part is modelled as a coat (i.e. covering). Applying the programme ABAQUS, there were created...
-
Ideological and Practical Model of Metaontology
PublicationRozwój inicjatywy Semantic Web spowodował rozwój różnych języków definiowania wiedzy i manipulowania nią. W ramach tych języków istotnym elementem jest zaprojektowanie rozkazów terminologicznych. W artykule przedstawiono sposób realizacji zapytań terminologicznych w języku KQL (Knowledge Query Language), służącym do dostępu do systemu zarządzania wiedzą RKaSeA.
-
Model szpitalnego oddziału ratunkowego
PublicationArtykuł omawia prawne podstawy tworzenia i funkcjonowania szpitalnego oddziału ratunkowego w świetle Ustawy o "Państwowym Ratownictwie Medycznym" z 2006 roku oraz rozporządzeń wykonawczych. Analizuje rozwiązania przestrzenne na tle franko-niemieckiego oraz anglo-amerykańskiego modelu oddziału ratunkowego. Opisuje przykład rozwiązań modernizacyjnych szpitala powiatowego w Kwidzynie.
-
Model of Volunteer Based Systems.
PublicationThere are two main approaches to processing tasks requiring high amounts of computational power. One approach is using clusters of mostly identical hardware, placed in dedicated locations. The other approach is outsourcing computing resources from large numbers of volunteers connected to the Internet. This chapter attempts to formulate a mathematical model of the volunteer based approach to distributed computations and apply it...
-
Model of Rules for IT Organization Evolution
PublicationThe aim of this paper is to introduce the Model of Rules for IT Organization Evolution which shall be in compliance with the Generic IT Organization Evolution Model. Due to its general nature, a set of practical adjustments is proposed in order to adapt the Generic Model to the IT Service Management domain. Further, two sets of rules describing the evolution of the IT Service Management area are defined based on two types of rules...
-
HYBRID REDUCED MODEL OF ROTOR
PublicationIn the paper, the authors describe the method of model reduction of a rotor system. The proposed approach enables to obtain a low order model including e.g. nonproportional damping or the gyroscopic effect. This method is illustrated using the example of a rotor system. First, a model of the system was built without gyroscopic and damping effects by using the rigid finite element method. Next, this model was reduced. Finally, two...
-
Correlation Effects in the Moshinsky Model
Publication -
Looking for a model of the contemporary university
PublicationPunktem wyjścia jest dokument Manifesto Empower European Universities dignozujący najważniejsze zadania czekające współczesne uczelnie europejskie. Są nimi: dywersyfikacja, umiędzynarodowienie i doskonalenie zarządzania. W tym kontekście autor artykułu zastanawia się na tym: gdzie jesteśmy?, dokąd zmierzamy? oraz jak tam dojść?, odnosząc pytania do polskich uniwersytetów. W konkluzji proponuje model uniwersytetu społecznie odpowiedzialnego.
-
Model of emotions for game players
PublicationAffect-aware video games can respond to a game player's emotions. Such games seem to be more attractive for users. Therefore for that kind of games it is necessary to create a model of the player's emotions to know to which emotions the application should react. The paper describes different models of emotions. The questionnaire and experiment for video game players is presented. Some results of the tests are shown. Then the model...